Good lord screw GE. Had to replace my motor but the board wouldn't reset the error code to let the machine operate, GE wouldnt tell me how to do it. Thank God for your video
I have an older model of the GE stacking washer / dryer and the wash light blinks and im hearing a clicking... it wont go into rinse at all .....could it be the lock sensor and how would i go about fixing it ?
Thank you so much for your video! One question, my stackable ge, does not spin strong enough, if you do heavy cycles or extra Heavy, and now it does on normal, if the cycle finishes, clothes end up damp, and i get an error code. It helps if i set a fan next to the motor to cool it down but not much. What can I do? Thanks in advance!
My GE is a bit newer but my on light stays the wash light blinks the rinse doesn’t the spin blinks and the lid lock doesn’t. Can it be the lid lock sensor/switch that goes to the board I replaced the lid lock thinking that was the issue.
I have a FRIGIDAIRE washer and dryer, yesterday I had power off from our house and I can’t make the washer to start!!! It has 11-red lights and 1-green light what should I do? Please I need your help, thank you
Just bought a ge stackable leds will light up for a few seconds then power will shut off again after we let go of start button it’s unable to go into troubleshoot mode atm (won’t stay on long enough) voltage looks great please Help!
I'm having an issue when running any wash cycle where the machine will begin to fill for about ~5 minutes, and then it pauses itself and the wash LED flashes. When pressing start again after, it then proceeds to finish filling and completes its wash cycle successfully. It is the SAME behavior every time. any ideas what could be causing this?
Just replaced the board because last one died ( no power at leds). It worked for a bit but I interrupted the cycle now it's stuck on a flashing spin led. Won't respond to diagnostic entry. Any ideas?
Anywho I put it back together but there were all sorts of bunji cords and I took most of them off it started working Anywho I need the schematics for this laundry center do you know where I can get that please
Your video made me look like a hero to my wife. I quoted you the whole time. It was our exact problem. And she found a missing sock. Thanks
Good lord screw GE. Had to replace my motor but the board wouldn't reset the error code to let the machine operate, GE wouldnt tell me how to do it. Thank God for your video
I've watched this video like 4 times already for the different fixes. Thanks a lot for posting!
Glad it helped!
You the man for this. Paused a rinse cycle and it refused to run again until I did the error code reset. Thanks a million
Thanks for watching Nicholas!!
Actual life saver! This is the monster useful vid I've seen so far!
Totally worked for me. I just had to wiggle some connections to get them tight again and boom! Good to go. Thanks for the video.
Nice Mike!
Bro! Thank you so much! Maintenance was taking forever to respond but using your vid, I fixed it myself. Thank you!
Right on!! 👍
Just had this issue and this video saved me! Thanks so much!
I have this problem every 3 loads so i watch this video all the time!!! Thanks!!😅😂
Best video about lights blinking . Thanks
Awesome man, had the same problem and the fix worth perfectly. Thanks!
I have an older model of the GE stacking washer / dryer and the wash light blinks and im hearing a clicking... it wont go into rinse at all .....could it be the lock sensor and how would i go about fixing it ?
Worked immediately what a game changer
Thank you so much for your video!
One question, my stackable ge, does not spin strong enough, if you do heavy cycles or extra Heavy, and now it does on normal, if the cycle finishes, clothes end up damp, and i get an error code.
It helps if i set a fan next to the motor to cool it down but not much.
What can I do?
Thanks in advance!
You are a God among men. 💪👌👍
Thank you so much! This help me reset my washer.
Thanks for watching Bri!!
Thanks so much, there was a quarter stuck in the locking mechanism.
My GE is a bit newer but my on light stays the wash light blinks the rinse doesn’t the spin blinks and the lid lock doesn’t.
Can it be the lid lock sensor/switch that goes to the board I replaced the lid lock thinking that was the issue.
Mine just started staying in the rinse cycle, not progressing to spin. It drains and spins fine. Not sure it’s the timer as the dryer works fine.
I have a FRIGIDAIRE washer and dryer, yesterday I had power off from our house and I can’t make the washer to start!!! It has 11-red lights and 1-green light what should I do?
Please I need your help, thank you
So helpful. Had to use the reset again.
Can u just fix the wire and reset? Or do you need to get a new one
It depends where it splits, or if you are skilled enough to solder the wire back to the part but I don’t have any experience with that
You just saved my life.
What about one that drains but no spin
After wash, the rinse and spin lights both flash and the load doesn't drain properly. What could be the cause? Thanks
Check drain pump for blockage 👍
Just bought a ge stackable leds will light up for a few seconds then power will shut off again after we let go of start button it’s unable to go into troubleshoot mode atm (won’t stay on long enough) voltage looks great please Help!
My lid locked in flashing red and has every single piece of my clothing stuck in water In the washer. What do I do
You can try turning off the breaker, taking off the front panel and manually opening the lid lock if it doesn’t deenergize
@@ApartmentMaintenancePro our maintenance is bringing us a new one and they got my lid open but thank you
Thank you so much for sharing!
I have same model washer but there is no power/ lights coming up.. dryer is working fine.. what could be the reason? Is it lid switch or board? Thanks
Currently trying to solve that issue for myself. Did you ever have luck solving it?
how much would this repair cost?
Can't answer this too broad of a question.
my lid switch blinking what it means?
I'm having an issue when running any wash cycle where the machine will begin to fill for about ~5 minutes, and then it pauses itself and the wash LED flashes. When pressing start again after, it then proceeds to finish filling and completes its wash cycle successfully. It is the SAME behavior every time. any ideas what could be causing this?
Did you find any solution. I have the same issue
Just replaced the board because last one died ( no power at leds). It worked for a bit but I interrupted the cycle now it's stuck on a flashing spin led. Won't respond to diagnostic entry. Any ideas?
low voltage short somewhere? USUALLY, when boards don't dish out error codes anymore it means they are toast. Generally work on last decades models :)
Please help someone my LG stackable washer dryer will not fill all the way it only fills too small loads no matter what setting I put it on..
‘Might’ be a pressure switch
Thank you so much 😊
My lights keep blinking after a couple washes .
Check the error code via the tech sheet and see what the error code is, it’s probably non critical
Great video, thanks'
Thanks Magno!!
OK i need some help some tweaker came by and tore the washer apart if didn't work
Anywho I put it back together but there were all sorts of bunji cords and I took most of them off it started working Anywho I need the schematics for this laundry center do you know where I can get that please
I would search your model number online or contact the manufacturer
The lid light keeps blinking and will not cut off even if it's in the off mode. What do you suggest?
Life saver thanks !!
Thanks for the video
Mine has a crack in the same spot 🤣