Fully Built Nissan SR20 Engine Assembly With Mazworx | 600HP
ฝัง
- เผยแพร่เมื่อ 7 มิ.ย. 2024
- As seen on @ThatRacingChannel
Jay Meagher and long time Nissan guru Mark Mazurowski dive deep into the world of Nissan 4 cylinder engine building in this detailed SR20 DET assembly video. Throughout this video you'll find tips and tricks that can help you along the way in your build, as well as some insight into the aftermarket support on these engines from two industry veterans.
In part one of this SR20 series, we tore down this engines core, and found some areas that needed attention: • Fully Built Nissan SR2... .
Teaming up with Mark from Mazworx Racing Engines, we were able to put together a new longblock capable of reliably reaching the customer's horsepower goal of 600hp. Interested in seeing more Nissan engine content? Let us know in the comments below in the video, and we'll work your ideas into our video schedule!
Build List and links.
- Long Block Package similar to this build.
www.mazworx.com/sr20det-rwd-l...
- Short block Package similar to this build.
www.mazworx.com/store/p/408-M...
- Head package similar to this build.
www.mazworx.com/sr20det-stage...
SR20DET S13 Head, Stage 0.5 (Machine work at Mazworx)
- Disassemble Head
- Hot Tank/Clean
- Remove/Drill/Tap/Replace Oil Port
- Plugs, SR Head
- Machine for Threaded Freeze Plugs
- Remove, Reinstall, Ream Valve Guides
- Valve Job, Multi Angle
- Set Rocker Level
- Resurface Head
- Assemble Head
Parts:
- Brian Crower Stage 2 Camshafts - Street/Drift Spec #BC0205
- Supertech Valve Stem Seals
- Supertech Titanium Retainers
- Supertech Single Valve Springs, 68lbs
- Supertech Bronze Valve Guides
- Supertech Intake Valves, Std
- Supertech Incondel Exhaust Valves, Std
- Mazworx Threaded/Oringed Freeze Plug Kit
- Misc Plugs
SR20 Block, Stage 2.2
- Disassemble Short Block
- Hot Tank/Clean
- Sand Blast Block
- Remove/Retap/Replace Oil Port Plugs
- Machine for Threaded Freeze Plugs
- Sleeve Install
- Resize Cylinders
- Use Torque Plate During Honing
- Step Deck
- Resize Line Bore
- Oil Groove Machining, SR20
Parts:
- Darton Dry Sleeves
- Wiseco 86mm 9.0:1 Pistons
- Wiseco .866x2.500" .1969" Wall 5115 Material Pin Upgrade (Chamfered)
- Brian Crower ProH2K Connecting Rods w/ ARP2000 Fasteners (17mm width bearing)
- Nissan SR20 Crankshaft OEM 86mm
- Oil Pump, SR20DET S14/S15
- Mazworx SR20 Main Stud Kit
- King Bearings Rod Bearings STD 17mm rod
- King Bearings Main Bearings STD
- King Bearings Thrust Washer
- ACL Thrust Washer
- ACL Race Main Bearings STD
- Tomei Head Gasket 87.0mm Bore 1.5mm
- Mazworx Threaded/O-ringed Freeze Plug Kit
- Mazworx Front Oil Squirter, SR20
- Mazworx Billet Breather Adapter
- Mazworx -10AN/Plug Water Pipe
- Misc Plugs
Links:
- Mazworx SR20 60-2 Crank Only Sensor Kit For RWD ATI
www.mazworx.com/mazworx-sr20-...
- Timing Chain Tensioner (Comes in Timing Chain Kit)
www.mazworx.com/store/p/98-Ma...
- Mazworx Front Oil Squirter (Comes in Timing Chain Kit)
www.mazworx.com/store/p/347-M...
- Timing Chain Kit
www.mazworx.com/store/p/313-M...
- Valve Cover Washers
www.mazworx.com/mazworx-sr20-...
- Head Studs
www.mazworx.com/store/p/141-M...
- Engine Bolt Kit
www.mazworx.com/store/p/133-M...
- OIl Pump Pickup
www.mazworx.com/sr20det-rwd-o...
- Extended Oil Pump Drive
www.mazworx.com/oil-pump-cran...
- Crank Bolt
www.mazworx.com/mazworx-sr20-...
- Main Studs
www.mazworx.com/store/p/132-M...
- Water Fittings
www.mazworx.com/sr20-rwd-wate...
www.mazworx.com/sr20-rwd-wate...
- Breather Adapter
www.mazworx.com/sr20-breather...
Thank you for watching! Don’t forget to Click SUBSCRIBE & turn on post notifications, click the bell 🔔 icon
👉 www.realstreetperformance.com 👈
sales@realstreetperformance.com
Phone: 407-695-7223
Text / Whatsapp: 407-724-2484
•Follow us•
Instagram: / realstreetperformance
Parts Instagram: / realstreetperformancep...
Powersports Instagram: / realstreetpowersports
Facebook: / real.street
Twitter: / realstreetrsp
TikTok: www.tiktok.com/@realstreetper... - ยานยนต์และพาหนะ
![+700HP SR20DET Engine Build - Full Start to Finish [4K]](http://i.ytimg.com/vi/TvqgprMMn8g/mqdefault.jpg)
![+700HP SR20DET Engine Build - Full Start to Finish [4K]](/img/tr.png)
Finally, someone in the US who knows the potential of this platform. The US is the only place where no one knows how to build an SR20 properly; I remember 10+ years ago seeing a Datsun with an SR20DET in Puerto Rico running 6 seconds when NOBODY was anywhere near those numbers. I'm talking no Honda, no Mitsubishi; some 2JZ were in the 6 secs, but those had 2 more cylinders.
Ahhh. Youve been paying attention. Well done. The Aussies also build some monster SR20s as well. Infact Micks Motorsport in Australia did 6 second passes with the oem cast block SR20 back in 2013. A 6.91 at 206mph. I think.
@@conradsealy9603Yes, some of those car's videos are still up and you can see the upload date 😂 10-12 years old.. Doing mid 7s and low 7s until they finally cracked into the 6s...
😂
building my 280z with a sr20det now :D
As seen on That Racing Channel. You can now view it on our channel. We save these videos on our playlist so you can stay up to date with build videos. Thanks for watching!
Where can I get a high torque electric motor from?
would love to hear "jays" thought about this: "can engine be damaged internaly with adding oil while the engine is hot?"
Im suprised they didnt use the dual guide shim mod on the rockers. Really cool engines those SR20s. Lots of power potential. The Aussies also build some really powerful SR20s as well.
because its debatable if it even makes any difference when you ensure everything else is correctly setup.
Two of the best here, pay attention everyone.
You ain't wrong about that if you want an SR20 done right these two are the goats
Thank you @noclassic
damn its crazy cause back then it was such a cheap engine to obtain. now its more convenient to ls swap or k24
Indeed, you are a wonderful man who never stops using the SR20 engine and we are impressed with your explanation and clean work 👌😮💨⚙️
I always enjoy your videos, Jay, but especially enjoy them when it involves the SR20 and the masterminds behind Mazworx.
Going to re-sleeve my SR20 next year and going the HKS 2.2L route. Going to also use a lot of the Mazworx parts that you guys used on this engine, and cannot wait!
I have a spare SR20 in my S14 at the moment, completely unopened lol, but the one I am about to rebuild has detonation marks around the upper edge on the factory sleeves, and the pistons are damaged from going too hot. Bad tuning and chipped OEM ECU before my ownership.
Looking forward to it though, gonna assemble it myself.
That's awesome to hear Sebastian! Good luck on the build, Feel free to reach out to us if you need any help with your project.
Mark has really put everything into developing the sr20 platform, through all these years.
I met mark back in the 90's when he had his teal green S13 Silvia coupe with the CA18DE-T and he was roomates with that short Jewish guy with the 200sx ....
All of Mr Jay " s .... Videos are very helpful ....
One of the best engine builds for innovation I've seen on TH-cam. Thanks for sharing.
I feel like im in a dream watching Jays Videos with that music in these videos .... Absolutely Amazing man 😴 😴
Glad to have seen this video, as I’m soon to have one to work on. Keep up the great work!
Wow what a treat !! 🙏🏽
What a great informative video! Absolutely love it Thanks Jay! ❤
Glad you enjoyed it!
Would LOVE to see this turn into a series!!! Have Mike from MotoIQ on next to do a honda engine! Then the HPA guys on to do a Burra engine!
Amazing content! Thank you
You guys rock kid
Hey Guys. Thanks for the knowledge.
We are happy to deliver these! Thanks for watching.
Buen trabajo muy bien.
wow! very imformational. Great to learn from peoples like J and Marchk
Glad you enjoyed it!
I like the torque in the ka24de motor ....
I recently had an SR built by Mark and the Mazworx team, the whole process was amazing, highly suggest them for anybody trying to have their SR built properly.
How much was it ?
How much did it cost ?
@MsXfusion I did the 0.8 longblock package. It's about 10k on their website
I might be getting a 2015 Hyundai Veloster Turbo .... Towards the end of this year So ive got to listen to Jay ! Their known to break alot of connecting Rods & i need 2 know Why & a few other problems
🔥🔥
5 hole bearing is also 19mm wide opposed to 17mm for the single hole, much better part
would love to hear "jays" thought about this: "can engine be damaged internaly with adding oil while the engine is hot?"
question on dual shims, has mazwork develop or found a way or any research on dual shims guide
Curious as to the reasoning behind using OEM main-caps but going all the way to sleeving the block. would have expected to see some kind of aftermarket main cap and/or main-cap brace/girdle. Great video informative video with some handy tips!
Less prone to detonationm and replaceable, with aftermarket sleeves.
When Nissan made those engines, they sprayed in the material for the OEM sleeves and machined them to spec afterwards, leaving an edge just above the first piston ring towards the cylinder head, making them more prone to detonation and can easily get damaged.
I doubt the owner will make a lot of power with it, and it's always good to re-sleeve, IMO. I have damaged OEM sleeves because of detonation in my S14's SR and will replace the sleeves next year before I assemble it.
no dualshim guides? curious
Jay What is you favourite 4cly engine platform and if so why
Awesome video, curious to why maz chose to use standard rocker shim and did not do dual guide?
I'm sure it was all planned for the owners liking and decided to do it this route.
@@realstreetperformanceor there is no proof to confirm dual actually makes 1 shred of difference.
If shimmed correctly, the rocker will be perfectly horizontal to the cam lobe. Having 1 or 2 guides really wont make any difference as both would be the same height. There should be no large side to side movement.
People dont setup, measure and shim correctly then wonder why rockers get spat out. Or they have aggressive anti lag or cut and it blows the rocker off.
Any feedback on the 3sge platform ?
You know i dont know what size turbine or what size fuel injectors.... Or how many pounds of boost this thing is capable of having & ..... Thats why i listen 2 Jay .....
Does Jay believe in Pre filling the oil filter .... And i think your only supposed 2 fill the entry holes of the oil filter .... But i havnt heard Jay .... Or the Power Nation .... Or Papadaskis in California say it so .......
Hey Cool 😎 Dood !
Aww man. Still waiting on another +1200hp b58 build
Sr20det S14 vct head gasket can use in s13 sr20det?
When are you guys gonna build another engine ?
Is there more scene?
any discount code for cc stage 3 honda b sereis??
What's the rough estimate of this build?
If anyone reading this has a cool Toyota AE86 that they plan on building with a mighty 4AGE 20 Valve Blacktop engine swap, please send said engine to Jay for a detailed build video 😃
Why no Dual Shim Guide?
when priming the engine, is sprak plug removed???
There are no spark plugs in the engine while performing the priming steps.
500hp in a small light car is going to feel like 1000hp in some of the heavier v8 cars that you normally see 1000hp in.
I'm thinking about building a sr with my son. I found one with a spun bearing, owner says it started knocking and pulled the engine. It's just 20 minutes from me, they are asking 1,500 for the long block. Think it's worth it?
Machining isn't an issue we have plenty of automotive machinist local. We would completely rebuild any motor we buy for this project even if it was considered a good running sr.
If it spun a rod bearing which is common, it probably be worth it but be ready to buy a crank shaft. Those are about $1000 and available still from Nissan.
anyone know a coupon code for the site?
In like 2000-2002 the junk yards near me used to have dozens of really nice looking S13's all over the place. Most of them just needed motors, and got parted out/crushed. At that time you were just like meh S13 who cares, a running one was $2k~$3k. Now today people want 7k for a pile of crap rusted out one.
My ford focus 😆 has flat tappets 😆 ....... That the camshafts lobes push down the titanium valve springs & valve stems 😂😂😂😂
Can anyone explain why a rod bearing with 5 holes in it is any good?
they explained it on last video
Jays says it it won’t be
A Super powerful motor at 4 or 5 hundred ponies…
I’d have to say 4 or 5 hundred hp is PLENTY for bout any motor of any size let alone for a tiny motor!😂
Jays says it it won’t be
A Super powerful motor at 4 or 5 hundred ponies…
I’d have to say 4 or 5 hundred hp is PLENTY for bout any motor of any size let alone for a tiny motor!😂
Whats Jay Doesn ' ?
why the reupload?
Video was released on That Racing Channel. We save these videos on our playlist so anyone can keep track of our engine build videos.
Can anyone give me a price on the build please
You know when Blake talks about modifications & upgrades .... I talk about upgrading pistons , Rods , Fuel injectors ... Properly tune .... The combustion process ..... NOT putting a k & n air filter kit on it .... Because their no one to trust to ... Tune my car .... If you ask me the factory.... Has failed me in .... This engine application ... So .... Anywho ....
You Need to send a bulletproof Coyote to Cleetus, it may not stand up to Cleetus because he breaks everthing, not need to send him a tune just an unbreakable Coyote.
Running 600hp no dual guide shim, standard rockers and hydraulic lifters you are asking for problems in the higher rev ranges. I understand this car will probably not be beat on but for the money you put in for such a head set up by mazworks anyone looking to rebuild the engine and has money get a VVL head you won’t look back!
Yet to see Jay use a screw gun…
Hyuandai aint worth a ... BEEP ! ..... Blake ... Likes ... Fords ... Focus st & Rs ..... Their legit !
Had a question! I’m working on a 2.3 turbo engine from the 80’s turbo coupe thunder birds and svo mustangs… the hot side of the turbo lets a slight white smoke from it, nothing from the exhaust tips just right at the turbo. And it only smokes after raising the rpm’s and engine being warm.
I’m thinking it’s the valve cover breather that’s clogged up causing excessive pressure to build. Your video from just about 6 years ago (jays tech tips) helped us understand more of what the probable causes are and we are going to get a new breather/separator and see if that helps.
Do you have any advice as to what could cause this??