วีดีโอ

Hey from the South Carolina Coast. Great vid sir. Really came out great. Just ordered a Marine Mat set for my Chaparral 256 SSX Waiting for it to come in the mail. Great tips. Thankfully I have snap in carpets so no removal headaches for me, just have to fill the snap holes. How's it holding up a year later ?

Nice quality video...I would recommend replacing the disc at the same time as the pads. The amount of rust shown on your discs makes me wonder if your brakes were even working properly in the first place.

Great video, thank you! one tip- put a couple lug nuts on to hold the rotor when putting the caliper back on. And My buddy turned me onto his find: the Kodiak 225 SS Stainless Steel kit! All stainless caplipers, rotors, bracket and pad backs. Pricey but worth it. Going to install next week.

Hey, have twins and one is running even in neutral. No fast but still spinning . What to do? How to solve this. They are brand new since finding use boat often.

WHAT a PRODUCTION!! Atza nice-ah gravy! 👌

Merci beaucoup ❤❤❤❤❤❤❤❤❤

I ❤ this video

How are the speakers and amps holding up ?

Good job

FYI. You must bend over the tabs on the outer pads. If you do not, then that pad will not stay in the proper position on the rotor. It will fall and wear the pads and rotors in the wrong place. Best way to bend is to put a wrench under the pad and pry up on the pad to hold it in place against the rotor at the hub. Then hammer them over. Doesn't take much.

How did it sound before upgrading your radio? Love all your content btw.

How did it sound before upgrading your radio?

Thank you for the explanations.

What materials did you use ??

Hey Mike, is possible to grease up the actual levers themselves? I put some on the outside, can see a rubber gasket but it looks like it should be on the inside of that. Just wondering if you ever explored that. Thanks.

Jet boats specially Yamaha are extremely bad. Stay away. Our engines 2024 busted after 2.5 hours. They told us that our warranty - 5 years warranty- one week old. It doesn’t work. So the warranty is useless

Jet boats specially Yamaha are extremely bad. Stay away from

Do they not make sea decking that snaps in to the existing snap in points

Thanks brother!!!,I have a vector system 2015 Yamaha 212x…

Great video! I wondering if you have time to diagnostic a problem of latly a yamaha sx192 2014 I have. TIA

What does this do?

Perfect video, Boating Propless! We've even put on our webpage under 'Support' it's so clear and easy to follow. Great work!

Great video Captain Mike! That was intense. Reminds me of the days when I used to install audio systems in cars. lol. Wires galore😊

Great video! Install seems straight forward and if a person had any doubts, your video makes its crystal clear. Would love to see what this device actual does and what the difficulties are driving the boat without it.

This was the best mod to my Yamaha hands down! Holds speed perfectly! Synchs the engines! So easy anyone can tow a boarder. Worth the cost and the install is simple.

Another great video, thanks for sharing. So all you have to do is put it on forward drive and gets to the desired speed? Just the fact that the RPMs are synched is good enough for me. Actually my port side gauge is not working atm so it is not bothering me 😂 Thanks again mate, these are so helpful.

Great video - Thanks !!

Clean install brother👌

I might have missed it but what size amps are you running?

Hey Mike, do those cables sometimes get bent back down under there. My throttle is stiff due to my boat sucking a wakeboard rope got sucked under. I think the rope pulled the cable rod or bent the rod to the bucket.

Awesome video. Almost what I’m going to have to do on my jet boat. I need to remove the rack from the boat itself 😩

Nice job. Also liked your video on lubricating your kicker shifter cable. I will try that on my Ranger Tug, and give you credit if I make a video.

I believe I have a fuse blown. Can you help with troubleshooting

Thanks for the video. I noticed at the end you had what looked like a pool nodle in the jet, what does that do?

Great video! Thanks for the plug bro.

Thank you BP for this. I just installed the Fins/Fangs on my 2011 AR240. Have you staggered the fins at all or have you left them both in the down position? Thanks again.

Thanks for sharing. A little intimidating but I think I can do it. Do you have a video on lubricating the intermediate bearing? Thanks again!

so my rotor looks like that...not shaving it?

Yeah but how do they "sound?" Also, why are the screw that you replaced them with better than the factory ones?

Will that spray work on wood as well? My carpet is glued to wood on my boat

Thank you!!!!! Thank you for sharing in depth the specifics of items used. Couldn’t find a video where people shared what size hose they used.

How much foam did you use?

Merci beaucoup ❤❤❤❤❤❤❤❤❤

ur background audio is way too loud compared to you.

Thanks good video! Although I may just replace both throttle and reverse bucket cable on my 2016 AR190.

Have you considered the one-man bleeding trick with a bottle filled with brake fluid? I saw a few videos on TH-cam and even the etrailer people said that it would work.

Can you help me, my brother, with this work? My father had this craft and I did not learn much from it. I am from Morocco and I am 31 years old.❤❤❤❤❤❤❤

Awesome!!

I bought a 2023 275 sdx. Twin supercharged and it was loud as hell. I did the killmat in the engine bay within a couple of weeks after delivery last year. And it was so cheap I had enough to do under the seats. That Helped make the 10” stock sub stop vibrating the heck out of the fiberglass too. I still Have left over killmat. I’ll Be doing more soon.