วีดีโอ

Traducción en español

You guys are great. Thank you !

Hello! I've installed my joke on my Quadrajet but I'm noticing that my fast idle cam isn't engaging when the engine is cold. As a result, my car idles very low (say 600rpm) when it should be higher. If I engage the cam manually by pushing it up while opening the throttle, it sits in place properly and the engine will idle at the proper ~1600rpm or so. Once warm, I can kick it down to proper idle at ~750rpm. I'm wondering if maybe I either installed something incorrectly or maybe my thermostat spring is on its way out. Have you ever seen this before? Thanks in advance.

Glad I found this video, I have a '78 Chevy c10 /350 sb and a quadrajet 4bbl carb, likely in need of a rebuild. I'll pull the stamped code and hopefully you can point me in the right direction for a rebuild kit.

Is the rod always in that higher hole in the actuator? What is the 2nd hole below it for?

Does the small step go up or down? This video wasn't very clear...

wish i watched this this before i tried to remove throttle blades..broke 2 screws..one primary one secondary..would they be ok with just one screw on reassembly..i know its not right but will it work

where can i find complete power piston assembly...mine was rusted in and destroyed..13:30 these are not reproduced..does that mean i am SOL...I hope not..I cant be first guy needing one.

my Q-jet is in rough shape.Secondary doors rusted shut.power piston rusted and totally destroyed removing and two screws broke off on primary and secondary shaft door flaps..Question ..would it be ok to reinstall with only one screw in a base plate door.one missing on a primary one missing on secondary..the other two are ok..I would like to drill out but they are so small..Thank you for the videos.I took so many photos but you cant beat live action..So very thankful..I took carb apart 3 hours ago and already forgot how to reassemble..LOL...carb in now soaking..Cheers.

No wonder my truck won't idle below 1600.. my fucking screw is missing

another great helpful video, thank you!

What if the curb idle screw is so far back, that it's not touching the lever? I am able to adjust the fast idle speed with no issues. My problem is my curb idle speed. I cannot seem to get it below 1000 RPMs. At times when the car is in park it moves up to around 1050-1100 RPMs. To me that seems kind of high, I am trying to get it down to 850-900 at idle, in park. Once I shift to drive it drops down and seems normal. Do I need to screw it all the way back in until it's touching the lever, and the make adjustments from there? Also, do I adjust the curb idle speed with the car running or off? I make my fast idle adjustments with the car on to listen to the rise or fall of the RPMs during warm-up. Thanks for the video and any advice!

Got everything you need for Qjets? How about a '65-'66 vac break? 😉 Great video! Very helpful!

Thanks - I've been trying to find those retaining clips!

What happens if my apt screw is missing ? I recently went to rebuild a quadrajet that has this system and wasnt sure what was missing from there now i know and now im worried i purchased junk do i need it ?

Thanks for the video, is it ok to adjust the main idle screw for a little more speed,does it matter that the throttle blades are open slightly on idle?

I’m a total greenhorn when it comes to Rochester Quadrajets, but I learned Holley 4150’s and the like just because it’s what I always had, Holley is very easy to maintain if you don’t disturb the throttle shaft, I would rather not try and repair a bad Holley base an opt for a new one, or whole unit. I need to build my Rochester to accommodate the new 402 Chevy BBC 9.5 to 1 comp. Dual plane L78 type mid rise , solid flat tapper Lunati 515 intake 525 exhaust 108 lobe sep. 104 intake center, 224 intake and 236 exhaust duration @ .050 , Hooker Comp headers, 3 inch exhaust and big block Flowmasters, electronic ingnition. I have a new 1901r candidate. Price please?

Ordered a kit from yall last week received it yesterday. Rebuilt carb today with quick overview of video. Now my 1970 cadillac 472 runs fantastic! Need to finish fixing choke operations. Otherwise its great! Thanks for making kits available.

When the choke is activated on the fast idle cam and runs at higher rpm is it possible to make it run smoother at that high idle speed? Thanks.

I honestly had no idea you could do this and I’ve had them apart a million times. I think I’m going to tare one sort and try this

I built one last weekend and forgot to put the spring back in for the power pump 💩 oh well it’s not that hard to take apart

Thanks for sharing. I like these carbs. Easy to work on and easy to teach

Haha you sound like ned Jarrett

Awesome

Working on an all original 1970 Chevelle SS with a 396/402. It has the short filter housing and filter but uses the plastic gasket at the end of the threads not the paper gasket up by the head. Have you ever seen that before?

Thanks for the intell you saved me on a promise i made and almost couldnt back up. ive built these before but it was like 27 years ago and i was stuck trying to set the floats . I appreciate it keep up the good work

How do I know if I should replace my float during rebuild?

I have a 7045583 and after installing the base throttle plate I can see some light after tightening with a new gasket. Any tips on what I should do to correct it? I can see light on the choke side near the secondary shaft. Iused a straight edge on the main body near that area and measured it with a feeler gauge and it is out about .012

Don't break your nails

Awesome video been super helpful

Like the video for sure, love to learn more….

Great video, had someone out to tune my quadrajet and messed it up, after watching this was able to re tune it and drives awesome

Appreciate you

If you didn't have those long ass nails it would have been a little easier for you just wouldn't have looked pretty

Thanks for the video. Always wondered why choke would never work properly. Finally got my 1972 Corvette starting and running great from a cold start like it did new. Thanks again.

My problem is that the choke door wont close all the way to start my choke adjustments. What to do to fix this

Have bought some of your kits and tools, good stuff!!

I live at 6,000 feet. Do i need to reduce my jet size (one size for each 2,000') similar to Holley? Carb on Chevy 305. Great video!

Was there a spring with the power piston

I have a stock 1986 Chevy pu with a Quadrajet carb. It doesn’t want to idle after it warms up or if I turn the a/c on. The idle speed solenoid does move out when the key is energized. Any ideas? After turning the “bolt” that comes out of the solenoid about half a turn it does idle better but when I go to turn off the vehicle it “diesels”, wants to keep running. I’ve also changed the EGR valve, pcv, plugs/wires, rotor/cap and checked for vacuum leaks. Still not sure why it won’t idle. Any help would be great. Thank you.

I’ve spent the last several searching for help with my carb… not only have you helped me identify my carb but also fix..I appreciate your channel

Super helpful thanks

I just need an air horn gasket for a truck quadrajet 1983. Do you have one?

Don’t have a hole for choke housing seal can you please help

Hello hey reach out to you a couple of days ago I was wondering what you would charge me for a new carburetor kit for my quadrajet the # is 17058213 the numbers below are 68 JBR I bought a new kit here in Wichita and I paid 37 dollars for it but I don't want to use it if it's the wrong one. Thanks again

Hello I just put a new carburetor kit in my quadrajet and for some reason I lost vacuum on the tube that pulls vacuum for the timing? What if I used the wrong gasket on the top side would that cause it to happen? Thanks Sir

Tolerance for a warped quadrajet, I have semi straightened it out but still have a 1-2mm gap from the centre to the secondary side where the 2 big screws go into the body. Base plate is also flat. I was thinking about making a set of gaskets to replicate and give myself another half a mm of tolerance or so on top of my new gaskets? Thoughts from anyone who sees this

Buy yourself a pair of flush nip cutters from dorman, Titan or Klein and you'll love them for stuff like this

Great video! Love it, always wondered about this APT thing

Does the APT system also affect the idle mixture screws? Could it be that if my idle is too rich (AFR of 12) that I would also need to turn down the APT screw in order to get the Idle Mixture screws effective?