วีดีโอ

How to get this diagnosis

Im having the same issue on a 2015 c300l. CPA module wont complete calibration because of those exact same 4 DTCs. Replaced the front sam cuz i was getting odd voltage readings and getting an odd ECM short circuit that im having trouble tracking down. When i tested that connection you have in the vid, it all checked out, but im gonna look at it again the way you did. Thanks for the video man. 12:26

Please help me sir. I am from Trinidad and Tobago. There is no support from the company here. I have a 2014 VW amarok with CSHA 2.0 tdi biturbo. It could not start due to bad electronic switch on the back of the ignition switch. It was replaced now vehicle says key not in range and it just cranks but no start. I have an error code in the instrument cluster (U111100 function restriction due to missing message.) I had someone look at the ecu and they tried an immo delete and it will start and drive fine. However there's no window control and the ac hardly blows cold even though the switch is on. Now when i switch off it will start back if not on the first then on the second try when the ecu light comes on. However if i leave it off for more than 5 minutes it goes back to the crank no start issue. Then i will have to get the ecu rewritten again. I am exhausted. Please help me...

Does this also work if the car was sitting for a while and changed transmission and the PCM code came on so the car won’t start ?

Hi, What diagnostic tool did you use to coding radar?

Great job, thank you so much for sharing

Sir thank you for this update, but sir my GMC TERRAIN has similar problem and I have check all what you just done now car start but my scan tool can't enter ecm and tcm not equipped

Hello, sir can this cause a transmission problems? I have some of this codes, and after 1 hour driving the car takes a lot of effort to move and the transmission kicks

Thank you for this wonderful video, did you have to reprogram the control module with updated software vis the Official Mercedes Benz server ? or were you able to do that with an aftermarket scan tool ?

Thanks for your video, you have helped me save a lot of time.

Good information big boss🎉🎉

That was a great video, keep up the vibe sir

Do you have wiring diagram for that connector? What does each wire do

Tengo mi radio bloqueado

De donde eres amigo

Can someone sum this up for me

Umm, not helpful if you do not have that $3k device :P

Big salute to you bro I clear my car with the help of your video thanks for this information

Would just replacing the seat with a used one with working sensors resolve the issue?

Hello bro, thanks for sharing. Please we have similar problem here in Japan. I will highly appreciate if you can help buy the GM tech2. I will send the money as soon as you tell me its available. Please reply.

Please try to keep your videos to around 20 minutes, the standard of most other high-level technicians on TH-cam. In these 2 videos we were looking at the scanner TOPOLOGY way too many times Brother, thank you for all your videos, wish you had time for more, cheers.

I watched that video when it was your TH-cam number, then saved it in my private library from your channel, #11, some time ago with the PROXIMITY ALIGNMENT PROCEDURE. Thanks for all your videos as almost 100% are handy to an experienced Tech. Cheers th-cam.com/video/AIwmKVgdIUs/w-d-xo.html

After you did your radio work?

I need technician

How much for the part?

This happens to the G35 too.Would you know if the M35 Yaw sensor fit the G35 ,as in capability wise!

Very useful video, thank you

I saw the same in my 2017 nissan Sentra today and i came over ur video, i guess i will have to go to nissan but the car still start 😢

We all drop stuff as mechanics. I was in the Air Force and the U-2 pilot had a bad altimeter. He was strapped in I reached over him to unscrew 4 screws and I dropped a screw. That scrubbed the mission and we had to pull the ejection seat out and part of the floor board to find the screw. So chit happens

Great job ❤❤❤❤❤ can you give me your link l want learn more

but any diagnosis tool do that

am so appreciative for your lecture. thank you so much

GREAT MAN... THANKS BRO... 😎😎😎

just did this and luckily I had already ordered a new PCV Hose for this car months earlier. Lucky I did because the valve in the bottom part.( near the turbo) eas completely gone. When you take that hose off if you can blow air from that bottom part then the valve is missing. On the new one when you look in that bottom part of that hose connector, you can clearly see the orange valve. You can actually suck through but you shouldn’t be able to blow through it. I simply took the new PCV hose. I got and cut the ends of it off to use instead of the old one. Not expensive at all on eBay or wherever anyways, I think this is something important people should know. If you did it without replacing the bottom part of that hose then you are probably missing that valve also. Should be easily remedied and replaced.

Niice video. Thx to you I had no problems. Made sure that jb weld was on too… thx

I have a issue with a 02 nissan sentra se r spec v it sometimes loses throttle response while driving i quickly shut it off and then start it back up and works fine wat can that be

Penso que no meu caso não seja essa a solução, pois o meu comando só deixou de funcionar após a substituição da bateria. E o segundo comando funciona perfeitamente, no entanto o comando principal nem sequer abre as portas. Isto só aconteceu após a substituição da bateria.

Tenho o mesmo problema, mas o meu comando só deu erro após a substituição da bateria do comando. Após a substituição da pilha, o comando nem sequer fecha e abre as portas. No entanto dentro do carro, após várias tentativas ele acaba por trabalhar, mas dá sempre o mesmo erro.

is work in opel meriva b 1.4 turbo 120hp year 2012 engine code b14nel ? ? ?

good video. thanks for sharing.

Were did you buy the original iprog.

Hi thanks for the video I have the same problem but after a few times it will start Is any way I can connect with you thanks I’m in manitoba to thank you

ITS 2021

Thank you. I am facing the same problem now. Do you mean that you took the connector out? Just wonder how did you connected the two ends of each wire. By the way, I ever measured the resistance between green wire and yellow/green wire. The reading was 57 ohms. It indicates some continuity between the two lines. Is it normal or not? Your response will be appreciated.

THANK U SUR IHAVE SAME FAULT ON QASHQAI J12 BUT I DONT HAVE WIRIN DIAGRAME FOR STARTER RELEAY CAN U PLEASE GIVE IT TO ME ILL BE THANKFUL

💐 "Promosm"

Smh sooooo if we don't have program we out of luck. What a waste of time

Thank you for your video

De donde saco la válvula pcv que instalo cual le puso

Hey thanks for the video i got a 2022 VW Polo automatic but when i start not crank or start but is showing key not detected hold key next to intended surface. vehicle wallet where is that???