วีดีโอ

It looks like the new trans cooler sheds heat towards the radiator - does that affect engine temps?

Where did you order that newer alternator??

This was helpful, as my softener was showing the same symptoms. So I ordered a new switch from Amazon, and the problem was still there. I was almost certain that I was going to have to replace the water softener, BUT THEN I took a closer look at the cam wheel that actuates the switch. It had a pretty good crust of salt and corrosion on it, especially in the recesses. So I scraped it all clean with a little screwdriver, and reset the machine again. It went into regen mode, so I will monitor and see if this truly solve the issue. So: make sure you look at the cam wheel and be sure it's clean enough for the switch to operate through its full stroke.

LMFAO! Next time read the manual.

Great job. Thank you.

When you put your Carburetor on did you use a spacer? If so what size?

Best tutorial I found! Thank you!!

Take the deck off, clean it to the metal… 3 to 4 coats of primer… 3 to 4 coats of paint… done

Take the cross member off on the bottom and install from the bottom. 3 bolts on each side and remove. Cooler goes in from the bottom. Mine came with rubber bushings for the bottom mounts so it sits higher.

Simple look at the munchy crunchy rust or do something this is way better than doing nothing if you can't weld it in

Thank you Dan. Mine was doing the exact same thing. It was nice to see the same problem with a pretty easy fix.

Great video man thanks so much easy money

Awesome, just did my daughters a week ago to realize today its upsidedown. First video I watched the first common sense that they crack their windshield. This worked perfectly

A repair at reasonable costs. A little more work, and it will be done. Without r,ust treatment of the very rusty parts and the also rusted floor panels, it will last from 12 o'clock til noon, as we say in Germany. Good work in vain.😊

I had that problem when I installed cork, didn't bother to read the instructions torqued it down installed the carb the works, only to find out the rear cork was completely off and dangling! Didn't bother to start it, only this time I removed it bought a Edelbrock not that cheap made in China (intake) crap which by the way didn't align at all and I had to grind it-I just gave up on it wasn't sealing correctly, the Edelbrock aligned correctly, I am very cautious now about what I am doing. My first rebuild!

Put it in from the bottom and you don’t have to empty your AC system

Rockin the 61 husky. Has the symptoms

Oil injection is the dumbest shit ever lol pumps fail and blow ur engines like the one I just got lol smfh stupid design

How well would semi batteries fit in the tray. I bought mine a year ago. It’s got a getto set up right now. Wanna do a proper one probably not much performance gains sucking hot air from the engine bay lol.

Do you need to have 5 wires for Nest ?

just what i needed Thanks

If you rotate the head to get the piston in is there a chance you are moving the piston ring to cancel the hole opening on the piston?

Use a Good Quality New Razor Blade. Old Blade edge can leave Scratch Marks on Glass. I know happen to me long time ago.

If it ticks do you have to replace them or just clean them?

That's wild that you got the lifters apart without using vise grips. I tried banging them on wood like this and all I did was succeed in driving the lifter 1/8" deep into the wood. It was not coming apart without pliers, very stubborn.

Thanks for the video I don’t have my dad around sadly he passed away 5 months ago and he would show me what to do so I am going to fix up my skidoo tomorrow by my self

You are advising people to use petroleum jelly on rubber O-rings! I suggest you do a little bit of research about that. You will find that it eats away at the rubber. Viewers, this is why you should thoroughly review the repair manual for your machine first and foremost before searching TH-cam because TH-camrs are not necessarily experienced mechanics

There's a big myth about not mixing the lifters up, Ideally yes try and not too, But I rebuilt an M54 top end on my 330ci with Ebay scraps, Different lifters in different trays with different cams😂 It's the quietest M54 you will ever hear😊

Excellent video on changing gas filter and gas line.

Thank you, Thank you for this video. I put the button on the wrong way and didn't know how to get it off. I really thought I had to buy another mirror but I didn't .This video really help me instead of using what you had on the video. I use a lighter and yes it came off. In the year of September 2023 thank you Jesus.

Can you just unplug the throttle cable ? Job done? Or you have to disconnect the hose from the tank , loop hose to the carb and loop hose to the pump ?

Is It easier to rebuild the top end with the motor still in the sled? I’ve got a 2003 Firecat 500 and I’m trying to decide whether to pull the motor or not for top end rebuild

Oh man thanks for this. I thought I was screwed. I am a little embarrassed to admit it, but when I was replacing the button after the mirror fell off, I put the dang thing on upside down. Even after telling myself to be sure it was in the right orientation. I noticed it pretty quick, but it was too late to change position at that point. Anyway, you saved my bacon brother.

Will this fit a 2002 f250 5.4 triton super duty?

You did an amazing job! Thanks for recording this tutorial.

💯🔥🔥

Thanks for using our products!

Great repair video, exactly what weekend warriors like myself look for. I have a rusted out 2002 F150 that’s about to receive the same treatment. Ignore all negative comments. We all know that there’s a better way but we all don’t have the time or money!

Just saved 300mbucks thanks man

You are a life saver. Thanks for being to the point without music and a long story for an introduction

Where did you purchase the tray to soak the lifters in? Which cleaner are you using?

Hey Dan could you post an update on how these look two years later? Im about to do the same operation on my Expedition and thank you so much for the step by step install. Also, what brand slip on rockers did you use?

Best video i have found for this!!

Damn. Thanks for this video man. Ive tried to paint the filler on before but i used a powder not a lspeckle wood filler stuff u used. I been using a rattle can hi build primer 2 in 1s This is going to help me so much thank you for this

Nice job! Take ur like buddy

"PIP Mark" for the top of the ring. It is usually a dot. Make SURE that the spiral circlip is all the way seated. Oh so the second cylinder has to be done properly?😂 The 1st one doesn't matter.

Dude, I have watched dozens of videos, and yours is the best, most well thought out one, straight to the point. Liked.

Thank you that was very helpful. I saw another video and they used JB Weld. He said it was way cheaper than the autobody stuff you used.

great job guys.....u explained everything good....

Dan, Thank you. I had suspected that this was the problem and you just confirmed it. Do you happen to know the part numbers for the fuel line and filter for a Husky Rancher 455? This is exactly what I was reaching for. THANK YOU SO MUCH BROTHER!-Paul