วีดีโอ

Brian, thanks for your comment. The 28MHz transceiver can drive any VHF UHF transverter. If you can find a 28 to 220MHz transverter, it would work just fine. I built the 28MHz receiver/exciter and connected in a transverter from a Ukrainian supplier. You could attempt to build the transverter part but its not a beginner or intermediate project. Good luck.

Thats a super interesting homebrew project and very modern! The 20w PA should be achievable with all the switching FETs to choose from, although you will need faster ones at 14Mhz. What MCU will you use ? Will you write your own software ?

Yes for sure, going back to when these jingles and signature tunes were in use, shortwave was a competitive place where nations tried to 'catch' listeners. All swept away by internet and social media.

It's not merda

Thanks for visiting

Thanks!

I didn't try it on short indoor antennas but I don't think it would work well. Ferrite rod front end might work better on LW and MW. Yes, almost any dual gate mosfet should work.

Sure, TL598 is an updated TL494 which should work fine in this circuit. They are probably not pin compatible so you might have to make some minor changes.

@@Paul_VK3HN thanks alot i like your videos an the projects you do would you please design this with t494 since tl 494 is most available my request

​@kittony71 Time is limited at the moment, I suggest you study some TL494 SMPS circuits, read the datasheet, watch some videos and try it yourself. Doing it yourself is the best way to learn.

@@Paul_VK3HN thanks am working on it right now

Thank you 🤗

Hi Jeff. I live in Melbourne but have spent time in NE Victoria for walking and portable radio fun over the past 7 or 8 years. I've been to Walwa, on the Murray, lovely spot. Re clubs not sure there are some very active radio clubs in Victoria suggest you search online , you could email Amateur Radio Victoria, very nice people, they might know. Also, find out the contact person for your local VHF repeater, probably Albury. Good luck 👍

What is confusing you about this project?

Thanks for your comment. The Arduino and display etc are mounted vertically on three pieces of aluminium angle, a horizontal piece and two vertical pieces either side. The big LCD is mounted against these verticals. The whole assembly is self contained and the base is M3 bolted to the chassis floor. You can see this in the video at 0:40 to 0:45 seconds in. Is that clear? To be clear, there are no bolts thru the front panel as you can see.

@@Paul_VK3HN ok Bro, i saw aluminium chassis which is Lcd mounted to , it is really genius action, your rig is really looks awesome, im your close follower. Thanks for your fast reply . Regards from Istanbul Turkey TA1TRX 73 👌👌👌

Good on you bro! The MST from OzQrp? I've built two of those a good design and well kitted by Leon VK2DOB. Good luck! Have fun. 🤓

@@Paul_VK3HN Exactly OZqrp, your countryman from Australia. I know VK2DOB and also i'm following him tube too. Thanks Paul for your support. Regards 73🙏🙏🙏

Your si5351 library is not being found by the Arduino compiler. 1. install the lib by jason NT7S; 2. Upload and run his test script or alignment script to your Arduino with si5351 wired up and verify all is working. 3. If your compiler still cannot see library .h files check you paths in Arduino IDE settings; 4. Then reload my sketch and try again. Let me know if you continue to have problems. All the Arduino help is online from mutiple reputable sources. Good luck! SK . .

Hola, gracias por comentar. Cada gran proyecto son muchos proyectos pequeños conectados entre sí. Comience con algunos módulos receptores simples, como VFO analógico, amplificadores y filtros IF, mezcladores, amplificadores de audio y el conocimiento práctico se obtendrá poco a poco. ¡Buena suerte! ¡Es un pasatiempo maravilloso!

KISS (keeping it simple). And I don't mind the sound of AM signal fading, it is a nice sound complete with amplitude variations and phase distortion which I expect a working AGC wold smooth out. And yes the RF preamp stage adds 12-15dB or so which can be useful, it depends on your antenna.

Yes that's right. The receiver VFO is signal_freq + 455, when you go to transmit the VFO is on the signal frequency for AM. This is very easy to do with si5351 PLL clock generator and a microcontroller.

Thanks very much Simon. About 18 months later I came bamk to this project and did some more work on it, mostly adding the remaining bands, bolting everhthing down, and I added a proper AM detector, video here: th-cam.com/video/uasUCzHxIcg/w-d-xo.html

Thanks for commenting Dave. You are right about simple receivers and transmitters demonstrating the 80/20 principle. Another way that I think this is true is that the last 20% of a radio project in terms of features, sometimes takes 80% of the total effort. Which is all to say, as far as HF QRP radio is concerned, simplicity has a lot going for it. My Tentec DC Receiver is safe in its box, it did enough to hold off part stripping or an eBay listing, so it will come out again someday, sooner or later, for another evaluation. Maybe it will be a collectible next time. 73 Paul.

Good tip! Thanks. Actually my tools are quite basic, a proper workshop would produce improvements. BTW I used methylated spirits as a lubricant coolant when tapping M3 holes in aluminium heatshrink material.

Thanks

Thanks, it's just pure old fashioned linear circuitry from antenna to speaker.

@@Paul_VK3HN cant beat that. I am getting ready to build an airpal radio kit. Not at your level but should be fun

Thanks Michel, there's another video made a few years later which shows it more completed. th-cam.com/video/uasUCzHxIcg/w-d-xo.html

Thanks, I agree with your comments! Persistence is rewarded!

There's still a lot of 160m AM activity here in VK3. Thanks for commenting!

Microcontrollers and PLLs are amazing.

The Lcd library I used takes the number of rows, columns as arguments to the constructor. It's easy to do!

@@Paul_VK3HN but on the display is two bar .?

​@@syarifudin8941I'm sorry, I don't understand your question. 😢

Sorry sir. What use I2C the board arduino to lcd is 20x4 ?

@@syarifudin8941 I did not use I2C to connect the 20x4 LCD to the Arduino. It is wired direct, in the usual way, just the same as you would wire a 16x2 display.

Good luck, there are lots of designs for si5351 and ATMega328 microcontrollers.

You could do the board layout with kicad or similar. At the time I'd not learned everything you need to do board layout. I've subsequently made a number of boards using EasyEDA from JLCPCB. I will still do handmade boards for small pieces.

Yes, you can create a board in EasyEDA print it on glossy inkjet photo paper using Laser Printer, and copy mask from paper to PSB using hot iron or laminator.

​@@sergeykizilov38That would work. I haven't tried it. Lots of makers have. I'll do more off shore fabricated PCBs in the future, using JLC or similar.

Mate, look at the date!!

@@Paul_VK3HN my bad :)

I made all of these cases by hand, just using hand tools. All using aluminium sheet bases and tops, angle sides, front and rears, fastened with pop rivets, and nuts & bolts ranging from M2 to M4, but mostly M2 and M3.

You can do it! Take your time, one board at a time, and you will learn more than you know! Good luck 👍

@@Paul_VK3HN 👍

Tnx Trevor!

Tnx Peter.

Glad you like them! Thanks for commenting.

Thanks John. MW and LW are remarkable bands. We hams have 472khz, 630m, and 137khz, 2200m. I've never transmitted on LW but have listened to a VK3 who was a regular, and he used to say 630m was better than 80m and 160m for reliability. WSPR attains it's remarkable range because of the slow data rate and digital decoding in SDRs. 20m band has improved since this video was made and Au to US and EU propagation on very low power WSPR occurs routinely now. It will never cease to amaze me what radio and the ionosphere can do. 73 Paul VK3HN.

You do need to keep your pens fresh. But I used the same pens for over a year, with no issues.

Thanks Daya. There are a few errors on the boards . I intended to do a second run to fix these, but life got in the way. So I prefer not to release this project, as people would need ti.e consuming email support. I hope to get back to this so.eday. 73 Paul VK3HN.

Tnx!

Thanks Matt. It was a fun project. Haven't used it much on 10m, must get it out now that the band is working!

Thanks for the nice comments Frank. It's a cute little analog rig and fun to use. All the best to you.

Tnx.

Thanks Keith, happy building.

Thankyou, I hope your project goes well. I invite you to leave comments below my blog pages for this Controller if you have any questions. Best 73.

🤓