วีดีโอ

Video is inaccurate

I live in Lansing, IL and just bought a new car last week with these tires on them. I am not sure what to expect, when there is ice or snow on the ground. I am assume they will work out for the better.

What about engine relay? My car heats up and the fans don’t turn on when the temperature gets high. But the fans actually work

I just drilled a hole and it worked 😊

You may need to edit the video and show the continuity test on the new unit, does it have signal on the middle connector? I think the answer is "NO".

Had mine cloned moved it over on radiator brace ,simple job ,so far no problem

Thanks sir, my problem is same in this December 2024😢 (my Saab status: not run, can't start the engine). I already try use jump starter and jumper with the other car, but still don't work. So now I will try buy ECU in eBay, any advice?

My 2009 Acura tl no open no close the doors only panic working

My 2009 Acura tl no abre o siera las puertas con el viper trabaja solamente panic..

Will Prestone Max Pink be compatible as well? I own a 07 Saab 9-5

Were these the HT51s?

So how did you get the black part out?? I’m in this situation

He’s using aftermarket key fob that’s why. Keep with OEM ppl and you won’t have to deal with this. My key has never got stuck

im going thru this now. im sad

Until it tells you to enter key in slot

Hey my 2010 Saab cooling fans are not working

Tons of bollocks. It starts working in the morning not because you moved it manually a hundred times but because of lower temperatures. The problem gets worse in warmer weather. The case of the problem is a cold solder joint inside the lock itself. The only way to fix it properly is by soldering it again.

Thanks

Upgrade ur panel,seen at least 3 breakers that are double tap

WD40👍

Beware of where you put your hose clamps. If you tighten the exhaust to the frame, the car will shake.

The internal components that are on the printed circuit board inside the ECU can handle heat way higher than the engine is capable of outputting. However the life expectancy of those parts is limited and there is also a standby voltage present in the ECU so when the car is off it's kind of still on. All this hype about putting a shield under it is nonsense. The chip that fails in which you replace can take twice the heat so explain that... I've proven this with 4 sensors in the engine compartment in which one was inside the ECU one was attached to the bottom of the ECU and one was attached to the top of the ECU and let me tell you the interior temperature of ECU was not even close to being a problem. I'll need to make a video on this just so people actually know the truth.

I havent had any issues with mine, my brother in law put my fob in and it didn't get stuck but we was in park and came right out. I usually just set it in the cupholder

Over the last several years I have had 3 sets of these tires and I am planning to have them installed on my 2021 Dodge Durango Gt. These tires have exceeded my expectations and are a good value.

How to open the driver's door when the lock is broken Saab 93 2009

For anyone watching, you can prevent this by just relocating the ECU. highly recommended as just replacing the broken one won't fix it for good, the new ECU will fail as well at some point if you don't relocate it. you can thank GM for this.

What to you mean "drive the car two or three key cycles"???

Huge black eye for Saabs.

As an appliance repairman, theres always going to be water in there unless the unit hasnt been used in awhile. What happens is you put in detergent and then you close the lid, it fills up with water and then it makes it over flow down the straw looking piece and so the water pushes out the detergent. The only hole is the one down the tube so theyll never be dry. Unless like you did, bought the new part's or you can drill in a small hole

All common sense

My heat shield was completely loose and rattling… but it was on the top. The bottom is hard steel with no shield… does this mean it’s already fallen off? Mine didn’t have any screw holes. Looks like they tack welded it or something. Also, Harbor Freight has stainless steel zip ties. Probably even easier to use than the hose clamps.

your video seems to just slander a parts company's name. my coolant cap was original and did the same thing parts fail big whoop same car

We have two of these cars. My friends and I performed the timing-belt job for both. The reason being is that the tensioner was making a racket at cold starts.

Good to know

I remember when I first got the car and played with the slot. Never gave me an issue. Just make sure the car is in Park.

He is using an aftermarket fob, they are slightly bigger than a oem.

Don't use pods detergent in your LG washer. I had the same issue took the blue dispenser out and surely the skins from the pods were added up and clogged the whole!!! Thanks for the video.

Helpful video, thank you for that 🙏. But that ,,aaaaa " and ,,you know " , kills me :)) i mean ,i dont know , that's why I'm watching it . :)😅

I will try this but I have a different issue where my some of my doors unlock by themselves if i leave the car locked for more than a day.

If gou open up the module you will see many cold solder joints on the connector pins at pcb. It literally a $1.00 fix folks.

Very helpful! Thanks for the detail troubleshooting guide

Is this the Red/Pink colour when poured?

Thanks!

Excellent video thanks!

Thank you for your quick detailed video and also for the suggestion of Hella brand of bulbs. I really love my 2000 Acura TL3.2 the journalists Car of the Year for 2,000. I bought my in 2013 with only 125,000 KM for only $5,000 Canadian in mint condition. It now only has 185,000 KM. I just get a dealer to change this bulb and quote the dealer and a dependable after market shop with a quality name brand bulb. I'll ask for Hella brand you suggested in the video if it's available.

This isn't suppose to have continuity on the middle terminal.

you should show people the noise before you fixed it. So it is much better to understand it.

Update?

Sort of misleading. It's incredibly difficult to change Acura TL bulbs without removing the bumper. You can get a the HB's, barely and with great difficulty, but not the lows. Acura really dropped the ball here. All the reason I would ever need never to buy an Acura.

A lot of waffling for nothing. There are already cutouts in place where you can re-locate the end of the spring in order to increase tension. Obviously you need to adjust both sides.