วีดีโอ

what is firmware

Is the orange one on esp32?

idiots at samsung, why there is no option to disable sound? If I attach smart tag in my car or on e-scooter or bike, I dont want thief to find it and throw away into ditch, before I can track him, tag must be quiet !!! Idiots at samsung absolute idiots...

Which Display do u have used?

What awg the cables is

I have a spare pi zero sitting around.. Cant wait to give it try with a boosted antenna

1:36 the motorbike made booting your Cardputer sound extremely impressive lol😂

How did you get that firmware on flipper zero where it’s sorted out

Hello, thank you for your video and 3d model for a spacer. I dont know if it is possible, i just wonder are there any ways to connect nRF24L01 module to a cardputer, i've tried to find any information about that but unfortunateley couldnt find any. There are ton of information how to connect this module to m5 stick but nothing about cardputer, because they are both using the same chip i assume that there should be some way to do this. That wold be really nice if you have any iffo to share. Thank you

Thank you !

Gosh darn reset button plastic!

Do you mind sharing which are the pins inside the gear knob that activates the P button? Id like to add a momentary button to put it to Park. In retrofitting a F80 gear selector, thanks.

It looks like the new brass bushings are shorter and result it a bit more non-parallel 'slop' at the jaws. Maybe a trade-off to increase the maximum jaw opening size? Oh, and very cool little RGB underlighting mod you have there.

Do you sell this ? I don't know how to build your module case. It is the best so far I've seen .

Looks great! I have everything on the workbench to try it

Thanks for the video (Bjorn Guy )

Plz do a vid on how to install this

Would love to see a build guide with the external antennas

These all look like props for an awesome hacker movie 👍😁

Looks like a great project, eInk is expensive, but perfect for so many applications 👍

Great looking! keep going brother!!!

I don't have a 3D printer can some one make me a case for the 5000mAh battery. 😅

Glad to have started joining the community this is some cool stuff

Tip/when using super glue. If you sprinkle baking soda onto the wet glue it dries instantly and 10x more durable. The government does it all the time so we should to.

Hi, great video. You make difficult things easy. I have the Momentum firmware on my flipper, is it necessary to flash it??... thanks a lot.

t1000e have a serious bug not receving messages 1 hop away - also when its turned on there is packet loss from nodes arounds .. too bad ..

Is there a trick to getting the satellite to snap into place on the board? I can’t seem to find the right angle unless I’m doing something wrong and I don’t want to force it. I’ve tried coming at from different angles and jiggling it in but it’s just not getting in there. Thanks

Im not circuit guy. But it just my dump idea. Instead of switch for G1 and G2 why not switch only for the volt only? Without power other 2 cannot power on right?

Can you provide flric pwnagotchi display , 3d print case stl file?

Is it possible to run Android Auto on this setup?

Did the antenna upgrade improve the signal?

Bro had beef with the antenna 😂😂

why we need a switch for those i2c device，due to the less power supply？

Which hdmi-port do i need?

What booths did you use for the coils?

You really need to start your videos with WHAT THIS IS before you HOW TO MAKE.

You really need to start your videos with WHAT THIS IS before you HOW TO MAKE.

Well done

Unfortunately I can't get the firmware flashed. I tried it several times by bridging the two pins and pressing reset. I also tried it by bridging them while plugging in as shown in the video on the website but no luck.

Is this one 433 mhz only?

What is this thing like what does it do

This will be good for gaming buttons

Any luck with small form factor project. I tried but unable to detect tag over cloud. Only if in same room or close by

Thanks for this. I was going to do this to my plus and the video is super helpful. How well does the stubby antenna perform for you?

Great video, how about a video how to use it

Hey mate, i love the videos, just wondering if you would ever make a tutorial for a Flipper Zero IR blaster?

Excellent!

Hey what gauge wires did you use on these?

My right ear enjoyed this video

This is awesome, will you be sharing the stl for the case?