วีดีโอ

Is there an easy way to repair the water pump? My Ena 5 doesn't pull suction at all when turned on. I'm assuming a bad gasket or ball but I can't find repair for them anywhere.

Thank you, you helped me repair my Siemens eq 500, which was not giving espresso. Thank you again !

Can I use any kind of silicone grease? Or is there a special one for food machines?

I have descaled it four time and still asking to add descaler ???i am using citric acid for cleaning( 10 gm in 100 ml water then added 900 ml water, i have also used the official Delonghi descaler

What is a silver plate?? Glinder?

At 6:48 you twist and turn that part (I don't know what its called). I have the EC685.R model and I cannot twist and turn. How do I get it lose? I see that your model is the EC685.M, is there a difference? I thought the letter might be the color (mine is red).

💩💩💩

Hello I have a Jura Impressa F50 when activated in the machine (remove Coffee) the Magnet drainage Valve IEC 230V sometimes makes a noise like ununuuu makes for a few seconds it seems that it is like activated and deactivated it is in the middle ground what may be happening it does not get stuck because I see the operation in the discharge valve below I removed the tray and saw the plastic valve makes the correct movement

Film dodany 3 lata temu, a przydaje się do dzisiaj. Mam Dinamic'ę od 1,5 roku, po 5 miesiącach była w serwisie (zatkany przepływomierz mimo wody z dzbanka filtracyjnego i filtra w zbiorniku). Pakowanie ekspresu i wysyłanie na serwis na 2 tygodnie to mordęga. Nie mówiąc już, w jakim stanie wrócił mimo potrójnego kartonu i wypełnienia. Ostatnio mikroswitch się zblokował i nie widział tacki, miesiąc później puścił oring w zaparzaczu. 3 lata gwarancji, ale chyba musiałbym mieć drugi ekspres na podmianę, żeby normalnie korzystać z serwisu. Zamówiłem uszczelki, switche, smar i ogarniam serwis w 30 minut przy okazji utrzymując czystość w środku. Twoje filmiki bardzo pomagają! Szczególnie przy pierwszej ingerencji, kiedy człowiek się jeszcze trochę cyka.

Hi I have question about temperature in this model, for me is about 70-80 C and coofee or water is not too hot, can be problem with termostat? Is possible that grinder? Thanks nice video

I'm pulling my machine to pieces just to give it a really good clean. This was very helpful. The only bit that stumped me a bit was when screwing down the black bracket for the piston at 12:00. When I screwed down completely, the piston was pulled too tight to the mount. I had to get a close look at 0:25 to see the proper extended position, and only tighten that far. Fortunately you have such clear shots!

Спасибо за ваш труд! Получаю огромное удовольствие от вашего контента. Сам ремонтирую кофейные аппараты и часто в сложных моментах пересматриваю ваши видео. Всё очень грамотно и чётко. Дай Бог вам сил и энергии. Продолжайте. Мы вас смотрим. Ваш труд помогает людям. Пускай и не все подписаны и ставят лайки. С уважением из Латвии

@yt.myworks mam pytanko - też kupiłem zapasowy ekspres w celu naprawy obecnego. I teraz problem jaki mam jest taki, że jak przekładam ekran z kupionego do mojego to ekran nie działa. Oba ekrany działają w każdym przypadku - w swoim oryginalnym miejscu i po przełożeniu - poza tym, który mnie akurat interesuje czyli po przełożeniu z kupionego do mojego obecnego ekspresu. :D To co zauważyłem to to, że wizualnie są trochę inaczej te ikonki namalowane na panelu dotykowym ale tak to wszystko jest dokładnie takie samo. Masz może na to jakiś pomysł? Albo byłaby opcja chwilę z Tobą pogadać na jakimś komunikatorze albo mailem? Generalnie to widzę, że mnie hobbystycznie interesuje dokładnie to co Ty robisz czyli czyszczenie i naprawa takich rzeczy. :)

Brilliant thank you. No coffee, no workee. But now workee again

Did you "find" the part, from some other stocks you've had, or made it yourself?

Very good video, Thank You ! ! !

hi ,my units desale ligt is permanently on and did not disappear even after 3 decaling processes, I used original delonghi liquid for desaling. any suggestions?

Hi i dont know the size and type of screws which you replace at the end of video.whould you mind sharing information about size and type of screws? And I should say that you did it so professionally. Tnx.

Hi, I disassembled and cleaned the Lattissima perfectly. Now when I put the pod in it doesn't drip anymore. But if I run the water without any pod inside, after a few seconds it leaks water into the tray. I tried everything but nothing. Is it normal for it to do this? Do you have an idea about it? I have some videos if you want

Could you please do a strip down video on a Delonghi Dinamica.

Merci beaucoup, j'ai fais exactement comme sur la vidéo, je n'ai plus de fuite. 😊

Question. If the machine starts giving less amount of coffee, what is the most likely reasons? There is no leak.

Mmh I understand the mechanical idea behind greasing the cylinder but won’t this come in touch with the ground coffee when making my next cup?

The coffee seems underextracted to me….I would grind finer, and adjust watervolume to fit the relativle small dose of beans: 5g beans should yield about 15 g espresso-drink….

Lubricate all orings before they are mounted….their seal is obtained by small movement in the groove….lubrication prevents wear and secure their primary function….

Excellent video - thanks for sharing! I need to do this to my Jura Impressa XF50. Where do you get the seals and valves from? And what types of grease do you use? Thanks!

What was that in Minuten 20:30 as Hose cleaner?

Супер, молодець, профи!.

I disassembled and cleaned the entire brewer unit. Put it back together and turned the machine back on. Now, when brewing coffee the water just falls into the drip tray behind the unit, not touching the coffee grinds. The coffee grinds then fall, dry, into the drip tray. Any ideas on what went wrong? Any help would be greatly appreciated. I have a Jura Ena 8.

I disassembled and cleaned the entire brewer unit. Put it back together and turned the machine back on. Now, when brewing coffee the water just falls into the drip tray behind the unit, not touching the coffee grinds. The coffee grinds then fall, dry, into the drip tray. Any ideas on what went wrong? Any help would be greatly appreciated. I have a Jura Ena 8.

Incredible… but I guess a repair like that would cost atleast double the price of the original 😅 or even more

Thank you for your video! I was able to fully service my unit. I also removed the bottom part of the coffee grinder including the drive gear. It is just enough to pull it up but could be stuck with coffee so have to be careful.

Hello guys, thank you for the video and the dimensions of o-rings used. I am looking for the diameter of o-rings used to seal the connections between the transparent hoses and connections to the mechanical valve, if someone has them, I'd be so glad

What is the purpose of the hose and white container thing is at 2:46 to 2:56?

Real impressed. You went above and beyond by polishing the plastics. Keep up the great qork

Great video! Love the detail and camera work. I am getting coffee out of the right milk coffee side, but no coffee from the left coffee only side. I can sometimes get water coming out if I rinse or if I grind a minimal amount of beans. Any idea about which part has failed? I will be replacing all the o-rings in the cleaning and rebuild but was curious.

Time to replace infuserO-rings?

Hello what product do you use to clean the pieces when they are in the water

thank you so mush .. i want to ask u if there any solution to get more finer grain coffee in the grinder to get more aroma

? What grease is edible? Ur putting it on the surfaces with will get liquid on them

Ja, anschaulich, aber das Gleitmittel ist dann im Kaffee, da es an der Wand des Zylinders und im Stempel klebt. Reste sind dann immer im Kaffee. Yes, clearly, but the lubricant is then in the coffee because it sticks to the wall of the cylinder and in the stamp. There are always leftovers in the coffee.

Our second and third attempts were unsuccessful. Due to the general problem with this issue, I think an explanatory video is necessary. Ground coffees are wet and coarse. Please make a new explanatory video instead of copying duplicate answers.

Hallo l have one machine and always go on and after few seconds go off l try everything can you help me with some tips 🎉

Hello how are you. I would like to know if you have the link where you bought this marker to paint the chrome letters Delonghi thank you and good job.

No idea what I did wrong as I have had Delonghi for years but the brewing unit broke leaver from the back. The one in the middle, little hidden. It was in peaces and of course made a loud sound, just like that something went through something. Never ever have had any problems with the cleaning before. Now have to find a maintenance for it. Sad day. I think I did everything like in this video. Thanks for the video :)

How to clean the grinder? I didn't see it covered in your video. Thanks.

good job!! i'm your big fan~ ^^

Smoothly done - worked for me as well … including the Tee of course, too ! Thank you very much

Danke für das detaillierte Video!

Mine had the exact same problem. Thanks so much for the video