วีดีโอ

That's one of the downsides. It takes about 10-15min depending on what I want to fly next. I usually fly an aircraft at least a week or two before changing. Here's a time lapse of me switching from an FA18 to an F16. th-cam.com/video/gSWrYgEBO0w/w-d-xo.htmlsi=I_DssQxtGXdn-nkW Thanks for watching!

th-cam.com/video/SOD6J4Up7qE/w-d-xo.htmlsi=reFEpyOkaQ0cmhj8 This is the updated version of my F18 Setup. The video has all the components and companies listed in the description. Yes, I have instagram. instagram.com/mrbrianag/profilecard/?igsh=MTcyenEya2FnbzhhMw== Or Mrbrianag

@ thank you man💪

Down on the deck, the lowest was 68 fps and 90fps in the skies. With Graphics settings pretty high. I can give you setting if you need them. Thanks for stopping by!

@@KarmasGhosts no all good. im planning to get a 3080 and checking the difference in fps. ty so much. im also only guessing what fps im going to get. not playing any moment but i just try to look for any type of benchmark for reverb g2

The base center stick mount is by Foxxmounts, but the MIP mount is custom-made by me that attaches to the Foxxmount.

@ thanks for your replies

60inch L Shaped Desk by Monarch. Thanks for watching.

😆 My bad, RTX Voice wasn't active.

May I ask you PC specifications? Because VR alone takes alot of processing power. Some streamers will have one very high end PC or some have a secondary PC to stream the footage. I've tried both and opted to use a High End PC. Best way to see if you're PC CPU bottle neck is monitor when you're in VR and streaming. If it's close 100% all the time then lower your settings as low as you can. If it's still high then you might need upgrade your PC. RAM, CPU, etc. Thank you for stopping by.

@@KarmasGhosts hello, thanks for your help. I’ll check that but I have a decent rig. I7 14700 64gb ram Rtx 4090

I can't speak on OS engines. I haven't flown them. YS91 SR -3DS engine is very reliable. Never had a hard time to start. I never did 3D flying with my 700. So I didn't see the lack of power. YS have 120s that mount on to 91 pattern. You should look into the 120s. Is there a reason you're looking into the older YS91 SR engines?

Thank you for stopping by!

Combination of Winwing, Virpil, Thrustmaster, and TekCreations. Thank you for stopping by! Here's a link for the full video with list of components in the description.

th-cam.com/video/7ailtuz-hMI/w-d-xo.htmlsi=2KOCrmEqDC8scbQs

😆 Thanks for the laugh and thanks for watching!

Thanks for watching! Here's a link to the full video and thr companies and components are listed in the description. th-cam.com/video/LLZQFtTssAs/w-d-xo.htmlsi=STe5ElHwVYykqjVC

The components are also listed in the description of this short.

Thanks, why did you change your name, J? To troll ED and Razbam. Hahah

It was pretty awesome to catch them here in the States. Thanks for watching.

Yeah, I wish Eagle Dynamics would make this for real. Thanks for stopping by!

@@KarmasGhosts no problem

I wish! 😆 Thanks for watching!

No, I'm not finding the buttons/switches with muscle memory alone. I try to acquire the hardware to match the specific cockpit that I'm flying. Then, I align the panels/controls with the VR image by adjusting the mounts. So when I reach out for a switch/button that I see VR, I will feel it in real life. Thanks for watching!

Yeah, I wish they did also. That's why I don't use the hook lever on the left side and installed a separate lever on the right for the hook. That way, work flow is good to go for carrier landings. It keeps the immersion. Thanks for watching!

@@KarmasGhosts any time man. Yeah i sent an email to them inquiring about them making Left and Right Vertical panels. We will see what happens.

I use a combination of a powered J5 create 7-Port USB 3.0 Hub and (2) Sabrent 4-Port USB 3.0 Hub. Thanks for stopping by!

I take all my hobbies to this extreme.

Lol...I know I know. The music I originally posted wasn't available on TH-cam. I just picked a the semi popular from the time.

Thank you and yes it is! Thanks for watching.

It's very immersive when what you see in VR aligns with the physical controls and switches. Also, workflow is more efficient when you don't have to use a mouse or motion controllers. Basically it's like flying. It's so immersive that I have multiple setups for specific aircraft. I won't fly another way. Thanks for watching.

For question 1. I use the Winwing Super Taurus ‐ I bound the Left and Right throttle over the hump (which Winwing designates as "buttons" 31 and 30) with Left and Right throttle to idle in the F/A-18C in DCS. 2. I have the Phoenix Version (No screens) of the MIP because I fly in VR. Thank you for watching and stopping by to ask questions.

Thanks for watching!

@@KarmasGhosts AND YOU REPLYED TOO OMG 😱

Thanks for watching! If you're interested in this setup all the companies and components are listed in the video description. Thanks, again for stopping by!

I try and have a cockpit that's almost 1:1 with the plane that I'm flying. Also I have a mounting system that I can adjust/align the physical control with what I see in VR. The downside is that it's expensive, and the setup is around 10-15 mins to switch out cockpit components when I want to fly a different aircraft. But the immersion is worth it by not using a keyboard or mouse. Thanks for watching and stopping by!

@@KarmasGhosts curious… what mounting system do you have?

@diegomatiz1214 I use a combination of manufacturers with the F/A-18. The Super Taurus throttle, I use the extended desk mount from Monstertech. The center stick mount, I use the desk mount from Foxxmounts. The Winwing MIP is attached to a custom mount I made. Thanks for watching!

I have only seen the mod for the UH/MH-60. Unfortunately. Thanks for stopping by!

I'm using the Phoenix MIP without the screens for VR users. I'm not sure how the Top Gun MIP interfaces with a VR headset. Thanks for watching!

Lol...that would have been a more interesting short!

@@KarmasGhosts Lol

Which two panels were you asking about? The Winwing PTO and PCR or the tekcreations UFC and Hud control panel?

@@KarmasGhosts the PTO and PCR, i would like to have mine mounted in a similar way to yours but I’m not sure how. Are you using monster tech mounts?

@tomwills9058 Yes, I'm using the Monstertech Table Mounts Long Version. I just used the stock winwing mounts, and I ordered thumb screws to use with the T slot nuts to attach it to the mounts. Thanks for watching!

⁠​⁠​⁠@@KarmasGhostswould it be possible for you to link the products you used to mount your PTO and PCR panel? Because i’m not certain how many thumb screws, T bolts etc; to order. Thanks

T slot nuts*

Thanks! I appreciate you watching the short and stopping by!

I use Thrustmaster F18 stick because it covers all the controls of the Apache until Virpil's Apache Flight Stick comes out. Thanks for watching!

Nah...I'm cheating. This older setup for the Hornet is nearly 1 to 1 and the mounting setup allows me to align the controls in VR. So if I reach out in VR, the physical controls will be there at my fingertips! Thanks for watching!

If you're interested in this setup, all the companies and components are listed in the description. Here's a link to my full video listing all the components. th-cam.com/video/7ailtuz-hMI/w-d-xo.htmlsi=oXPgk5TkysfqZC1j Thanks for watching.

Total Controls makes the AH-64 MFDs they are 8.4x8.4 inches. Here's the link. totalcontrols.eu/product/apache-mpd-frames-with-desk-mounts/ Thanks for stopping by!

Thanks for watching!

All the buttons were included when I bought the ACM panel from TekCreations. They only thing I installed were the ACM Button and Master Arm covers and reed switches, so the covers would activate the covers in DCS. Thanks for watching.

For control panels for the blackshark, Virpil. It's difficult to find a used Winwing Combat Ready Panel for a general purpose panel. I think a collective is very immersive, especially with the specific grip for the helo! Thanks for stopping by!

You're not a fan of the Super Taurus? Thanks for watching!

@@KarmasGhosts Sure I am ! Of course I love it, I just wish I had the time to buy one. I'm looking forward to the future throttle

On the F16 the chaff and flares are controlled on the flight stick. 4 way switch on the left side of the stick. It's called the Countermeasures Management Switch. Thanks for watching.

@@KarmasGhosts Thanks

Thanks, please standby for Episode 7 of my DCS setups! Thanks for watching.

Where can I get this mission / mod?

you have a hornet set up to.....Bob Saget

This is VR with a RTX4090. Thanks for watching!

It was hauling ass! Thanks for stopping by again!

T-45C Goshawk. Thanks for watching.

Thanks, Frank!