- 22
- 325 353
JnC445
เข้าร่วมเมื่อ 7 มี.ค. 2006
3rd gen 2010 Toyota Prius with a new fully rebuilt motor, first start.
3rd Gen 2010 Toyota prius with 290k miles, motor finally blew a head gasket. The old motor was replaced with a fully rebuilt 3rd gen motor with new updated pistons, rings, crankshaft bearings, rod bearings, all new OE gaskets and o-rings, FEL-PRO head gasket, cleaned/lapped valves and finally head was cleaned and skimmed by machine shop.
More details and build can be found in the link below.
priuschat.com/threads/its-time-for-a-rebuild.239141/
More details and build can be found in the link below.
priuschat.com/threads/its-time-for-a-rebuild.239141/
มุมมอง: 89
วีดีโอ
Irresponsive Garage door remote keypad fix
มุมมอง 30ปีที่แล้ว
Short video showing how to fix a garage door Keypad that is irresponsive to keypad inputs, hope it helps.
Idiot driver almost caused an accident
มุมมอง 999ปีที่แล้ว
Ran into this fellow massh0le the other day in Cambridge, MA. He drove through traffic behind me as if he was driving an ambulance and had to make it to the hospital in a hurry. Like a train I saw this coming from a mile, needless to say some choice words were exchanged. Location: Cambridge, MA
Aggressive cut-off almost causes accident.
มุมมอง 56ปีที่แล้ว
My car must be invisible; this lady had plenty of space to merge and take her exit safely if she had just crossed over behind me yet she chose to cut me off aggressively. Just take the next exit and turn around, why do you have to put everyone's life at risk by pulling this cr*p. I realized her stupidity even more so when I pulled up next to her at the intersection, she had three kids in the ca...
2007 Mazda RX-8 no start, engine is getting fuel
มุมมอง 1912 ปีที่แล้ว
2007 Mazda RX-8 refuses to start, I checked the fuel relay, fuel supply and the engine is getting fuel and line is pressurized. The motor doesn’t sound like it has bad seals and the car stopped working all of a sudden rather than a steady lead-in to no compression. I am trying to confirm everything else before buying the special compression tester to check compression, next step = check ignitio...
Almost T-boned this driver
มุมมอง 1172 ปีที่แล้ว
They must be giving out licenses in cereal boxes these days, this idiot failed to look both ways before pulling out in front of me. I am doing 35~40 coming down hill and turning at the same time, we missed by a few inches. Location: Nashua, NH.
HS724 issue
มุมมอง 3072 ปีที่แล้ว
Guy gets almost T-boned due to wake and bake.
มุมมอง 672 ปีที่แล้ว
I am heading to work at 4 AM in the morning and almost ran into this knucklehead. I was doing about 35~40 MPH, my light had been green for a few seconds as shown in the video before he decided to pull in front of me and then like an idiot stops in the middle of the intersection. We both had to turn onto the on ramp to route 3 South, usually you accelerate on the on ramp to merge easily yet this...
2012 Prius V engine swap
มุมมอง 1.6K2 ปีที่แล้ว
Just finished installing a 4th gen (2017) Prius engine in my 2012 Prius V. Just a short video of the motor in maintenance mode. Big thanks to youtuber "Fix that prius" for the in depth videos. The old motor had a blown gasket and was going through a quart of oil every 5~800 miles due to the pesky oil ring issues common with most 3rd gens.
Rear end accident off of the 95 S off ramp, Lexington, MA.
มุมมอง 1363 ปีที่แล้ว
Dashcam captured this rear ending accident off of the 95S off ramp in Lexington, MA. Excuse the woahs.
Close rear end call
มุมมอง 603 ปีที่แล้ว
I was the idiot this time, this is why you don’t text and drive , kids. I looked down for two seconds to brief reply a text, the car in front started slowing down and I didn’t. Thank God for pre collision warning system (the beeping that you hear in the video) as if it wasn’t for the beeping I would have surely smashed into the car in front. Even with brakes applied fully I wouldn’t have been a...
Yamaha YS624W
มุมมอง 1.2K3 ปีที่แล้ว
1988 Yamaha YS624W snowblower against hard packed snowplow snow pile. Dont mind the background noise or the videobomber :)
Toro timemaster 30” with Honda GCV190 motor
มุมมอง 12K3 ปีที่แล้ว
Transplanted a Honda GCV190 motor from ryobi pressure washer onto Toro timemaster that has a blown Briggs & Stratton motor. At the same time the factory jet in the Honda carb was replaced to a less restrictive jet.
Common cause of Sony tv T-con board failure
มุมมอง 15K3 ปีที่แล้ว
This is the third Sony I am working on with a bad tcon board, all three had the same tape that has been used, all three had oil residue on the back side that makes contact with the tape, I am no electrical engineer but oil/fluid on live circuits = no good.
Modified Honda HS1332TAS snowblower
มุมมอง 3124 ปีที่แล้ว
Honda HS1332TAS snowblower - Upgraded 50W/3A charge coil. - Drainzit easy oil change attachment. - 42W Cree LED light. - Ariens OEM hand warmers - Upgraded rear and side skid shoes now shown in the video but the machine currently also has Gripo bucket extension
still have it? running?
Yes.
Well I found a relatively cheap GCV200 on a dewalt powerwasher on Marketplace, the pumps on those have a design flaw and apparently break often. Adapted a new OEM toro pulley with a 7/8"-1" engine shaft shim (had to be heavily sanded down in a makeshift drill lathe). Then put some washers in the bottom of the pulley to space the shim up, welded it and a longer 1/4" key in (GCV200 uses 1/4" keyway). Then I welded some pipe over the thin part of the exposed shim so it would bolt on tight to the engine shaft. The gcv200 works awesome so far, super easy to integrate the key to killswitch and a throttle setup shouldn't be hard to add (personal preference). It does seem to go thru gas quick, but a throttle setup would help that a little.
I also drilled and tapped the gcv200 shaft 3/8"-24 I believe (standard mower shaft size) and ran a longer, grade 8 bolt.
Also make sure you use an OEM blade engagement cable. I had an aftermarket for testing when I first got the mower in bad shape and it was junk - the upper plastic part would just warp/bend and the PTO belt would slip.
Picked up another timemaster today from an old acquaintance that bought it brand new, non runner but he says that all it might need is a carb clean. I'll try that first, if that fixes it then great otherwise I have been researching putting a GXV340 or GXV390 on this machine, lets see.
Would be pretty funny to see how it does through long grass, 12" or more.
I just completed the swap to agcv190 today. It would be cool to see another one of these swaps with more detail. All said, it was a fun and easy job. Thanks for the great idea!
Sweet, I have the thirty inch
Got a GCV200 from FB Marketplace, came on a Craftsman pressure washer. Came back to this video to listen to what adapter you used for the pulley / output shaft. Will be running commercially
If you can find a GCV200 or 190 from a honda mower than you might not need an adapter as the output shaft is long enough. The powerwasher engine shaft is very short hence is why I needed to drill and tap the output shaft and use a 2.5" spacer (if I can recall correctly). Believe it or not I just used a deep socket from an old socket set and it worked perfectly, cant recall the exact size but OD is different for each set so you'd have to probably go through a few sockets to find the perfect one. The socket just has to slide into the stock toro pulley, you may have to cut it to get the right length.
only issue with the pressure washer is the shaft is shorter, but if you see my comment I just made, I explain in detail how I adapted a OEM timemaster pulley to fit properly. So far its been great, I need to run it more to check belt wear is all, but I think I got the spacing better than my last engine swap.
you might be able to get away with the slightly less complicated method JnC describes though, but already having a 120v mig welder (hobart 140), I chose to go a little further to ensure the pulley wouldn't slip or something in the future. I like to do overkill lol
I completed my engine swap from Briggs and Stratton to Honda gvc 190. It took some mods to ensure the shaft was aligned prefect with the belts & pulleys. The engine is running smooth. It was a great upgrade.
I still have the Briggs on mine but I tuned it up to 3700 rpm and it's a lot better... I just seem to go through a lot of PTO belts on it they are cheap and don't last.
hey there im gonna ask you a question about the Honda gx=340 motor linkage you had on here some years ago when you where adjusting it did u have it all hooked up to the carburetor when doing it ???
Cant recall if I had it linked to the carb at that point, it doesnt matter if it is linked or not, you are just trying to adjust/set the governor link arm in conjunction with the governor linkage protruding out of the motor, I hope this helps.
thanks buddy@@JnC445
Sounds beautiful. My 2012 Prius just failed the "white paper" head gasket test (no surprise there), with 259,000 miles it would be pointless to replace just the head gasket. Where is that shop located?
Hey ! May I use your clip in my video with credit and link ? What happened before-after this ? Where did this happen ?.
Hi,what cause my sony tv if i plugged in it show static white lamp at indicator.already check no power to tcon board.
Hey ! Can I use your clip in my video with credit and link ? What happened before-after this ?
Hi, we're working on a new project and we think your video would be a great addition. Can we include it? We'll make sure to give you full credit.
Thatt is the way to do it.
Peace JnC445 may i feature your driving clip "Idiot driver almost caused an accident"? fully credited! Thanks and where did happened? Stay safe!
Hey JnC445, do you have an email address at which we could contact you regarding this video? We would be interested to discuss a license to use this video if this is generally possible? (i.e. via email) :) Cheers, Felix
That's awesome. Wonder how he drilled and tapped the shaft. A lathe?
you can do it with a cordless, just have to be decent with it.
How you conect the Bealls yo u got a video how you conect everything
Nice1!! Do not waste another day - P r o m o S M .
NOBODY SELLING NEW TCON. IF YOU BUY IN EBAY IS COMING IN BAD CONDITION AND THE SAME CHINA. (TO CHINA AND HERE YOU NEED TO PAY FOR RETURN. IS BETTER TO BUY NEW TELEVISION. THE TEACHER ON TH-cam TAKING ABOUT TV 10 AND 15 YEARS OLD.
wrong
Hey man, may I feature it for a video? Full credits will be given to you, of course, thank you so much!
Your carb is dirty and you need to remove the main jet an nozzle tube and clean them with carb cleaner and a wire. Nozzle tube has over a dozen holes and they gel clogged up and when you put load on the engine it dies out. You can use a twist tie with covering removed or a pin with compressed air.
Thank you, the carb was cleaned using an ultrasonic cleaner so it was fine, the machine just had low compression. I honed out the cylinder, put new rings and it was back in service.
Hi! Can I include this video in my new compilation? In the description I will put the link to Your channel, while the name of your channel will be put in the compilation. Thanks.
any videos with this in action?
Peace mate May i feature your driving clip on my channel? Full credit for sure. Thanks and stay safe.
Hey ! Can I use this clip in my video with credit and link ? What happened before-after this ?.
Hello! Good to feature this clip for my video edit? I'll credit you with watermark on screen of course.
Hi ! Can I use your clip in my video with credit and link ? What happened after this ?
Hello how are you? Can I put this video of yours in my next compilation? With your channel credits in the video description and in the video itself. I await your reply
hi can i use your video in my new collection and also in youtube shorts ? Credit Ofc!!
hi can i use your video in my new collection and also in youtube shorts ? Credit Ofc!!
hi can i use your video in my new collection and also in youtube shorts ? Credit Ofc!!
Sure
@@JnC445 Thanks!! video uploaded
hi can i use your video in my new collection and also in youtube shorts ? Credit Ofc!!
Sure
@@JnC445 Thanks!! video uploaded
Horrible, horrible, horrible idea to text and drive. You can easily kill someone while you are distracted. I know of someone who decided that it was ok for him to text and drive. He crossed the center line and hit someone head on and killed them. He went to prison NOT jail. He is still there. You can not undo killing someone. Those texts can wait. Capisce? This message was brought to you by angry, fed up motorcyclists.
alter Schrott, Daumen runter
Hi there, could I feature this clip? Credit will be provided!
Sure.
@@JnC445 Thanks.
Hello buddy, how are you doing lately? May I feature your clip for my upcoming youtube episode? I'll credit you with watermark on screen of course. Thanks in advance!
Sure.
Hey, this is Revit up. can i use your dashcam videos in next compilation video? Linked and credited on screen. Thank You !
Sure,
@@JnC445 thank you!
hi can i use your video in my new collection and also in youtube shorts ? Credit Ofc!
Sure
@@JnC445 Thanks You
Hello, would it be alright if I feature this video for my next ep? Full credit will be guaranteed!
Sure
Hey bud, is it ok if I feature it? Credited.
Sure.
Hi, can I feature it? Credited on screen and with a link back to you!
Sure.
@@JnC445 Thank you!
You have a video of your RX-8 cranking but not starting. No diagnosis or troubleshooting.
Just got the car when I made the video. I was able to get diagnostic report from the mazda dealer the previous owner took the car to, it needs new coolant and apex seals. I am mulling over the idea of k24 swap or LS swap; I will update here once the project has a direction lol.
Hello, is it okay if I feature it too? Credit will be provided!
sure.
Hi there bud, can I feature it on my channel? Credited.
Sure
Holy shit. That thing sounds just fine.any idea as to which carb from Honda has that bigger jet?
Not enough horsepower, that engine doesn’t belong on there
Hello, may i use this video on my compilation? I will also put this video link on my description as credit
Would you have or be able to show photos of the setup on the crank shaft that you did? I have a dead Briggs that I need to replace and have a 30$ less than 2hr 190 I can grab. Thanks in advance
Hey ! May I use your clip in my video with credit and link ?
Sure.
Hi there, ok if I feature it? Credited like always!
Sure
@@JnC445 Thank You.