How I Taught Myself to Plastic Weld

แชร์
ฝัง
  • เผยแพร่เมื่อ 24 พ.ย. 2024

ความคิดเห็น • 124

  • @ClaytonBridges
    @ClaytonBridges  5 ปีที่แล้ว +8

    Check out the new description. I know there are alot of things that arent proper here, and I was in the process of learning.
    I mainly keep it around because it shows that I really wanted to make youtube videos.

  • @deankay4434
    @deankay4434 4 ปีที่แล้ว +9

    I think as several serious comments left below are actual experienced welders. I started with a stick or ark welder in the late 60’s, but got a MIG in 1984. The common or best practice is heat control. Since the parent plastic is thick but more of it, it will absorb more heat. Concentrate on the spot where these two meet, as you see changes in plasticity, introduce the rod. Now you are heating 3 items. Companies that make hot air welders and consumables tell you to push the filler rod into the joint of the pieces to be joined. Leading heat in front of the rod to soften the parent plastics allow you to melt in and mechanical joint the 3 together. Working on metal with a torch is closer to doing this work. As it melts at the joint, add the filler and move your heat onto it again while twisting the rod. Grinding a “VEE” shaped cavity helps it welding flush. Also, pre clean the area with isopropyl and lint free rag to remove dirt and other contaminants. But remember, to get good penetration at the joint, heat should be added first, then filler rod. Once some practice, it will come natural. Just keep the heat in front, even if you have to change hands. Right handed? Hold the heater in that hand, lead the filler, add and melts as slowly or quickly as able.
    ASE Master Tech since 1978 - Retired

  • @josephvance8900
    @josephvance8900 4 ปีที่แล้ว +10

    Thank you for the video..ignore the negative comments bro. You said flat out that you were new at it. You provided me with plenty of info and I appreciate you taking the time to do so. Thanks again sir

  • @avid0g
    @avid0g 5 ปีที่แล้ว +30

    >> The Correct Way

    • @simclardy1
      @simclardy1 4 ปีที่แล้ว +1

      Where do you buy your rods? I have had bad luck with pp rods. No matter how hot or clean they don't seem to bond properly

  • @chrisbraid2907
    @chrisbraid2907 3 ปีที่แล้ว +2

    Good plastic welding iron, that’s what I remember learning to plastic weld with back in my apprenticeship years …. Plastic items usually have a recycle logo with a number or name inside the triangle. Having a fan draw away fumes from your welding is a good idea, don’t blow across your repair while trying to weld but you can when your weld is finished …

  • @danielc.3725
    @danielc.3725 4 ปีที่แล้ว +1

    Great VID 👍.
    I just bought the, 80 watt, plastic welder, from H. F., & I am sooooooo ready, yee - haw!!!!

  • @robertmorris9998
    @robertmorris9998 3 ปีที่แล้ว +2

    Nice video, shows the learning process. Hilarious bit about safety and gloves, but they come off for the actual work lmao!

  • @teamrino5493
    @teamrino5493 6 ปีที่แล้ว +3

    I enjoyed learning about how to use a plastic welder, the many uses, different types of plastic rods and good safety practices. Nice work!

  • @kyle23011
    @kyle23011 7 ปีที่แล้ว +7

    Thanks for the video! I'm in the middle of prepping my dashboard for paint after cracking it. And as you said, PP is very common around the house. I've been practicing by mending laundry baskets and hampers aha

    • @ClaytonBridges
      @ClaytonBridges  7 ปีที่แล้ว +1

      nice! yeah I was surprised with how well I could repair my console on my car. Its such a great tool

  • @danr.graham9331
    @danr.graham9331 6 ปีที่แล้ว +8

    One good thing about the video is that is shows us another option for repairing something that we may normally toss in the trash.

  • @JS-xi5nk
    @JS-xi5nk 2 ปีที่แล้ว +2

    You should always keep the welder in front of the rod. Never on top or behind the rod. Keep the rod perpendicular to the weld ans push the rod into the heated material. You will get a stronger/cleaner weld with less distortion and ripple. Done correctly, you won't get any ripple.

  • @rollandelliott
    @rollandelliott 6 ปีที่แล้ว +10

    hook it up to a nitrogen or argon gas supply, helps prevent burning/oxidization of plastic.

  • @isaacritenburg2057
    @isaacritenburg2057 4 ปีที่แล้ว +1

    They make different tips for it that make it alot easier

  • @TheAnonymousartist00
    @TheAnonymousartist00 4 ปีที่แล้ว +2

    I would forget walmart, or target for bins.I would go to Goodwill, if they have a Good Cents Goodwill they sell everything by the pound so it would be way cheaper to use used items if your learning anyway...Just food for thought!

    • @peterford9369
      @peterford9369 2 ปีที่แล้ว

      You can also use old plastic fender wells or any plastic auto body parts.

  • @WindChill2011
    @WindChill2011 6 ปีที่แล้ว +8

    Nothin' wrong with this demo. Good job.

  • @zhengliu7194
    @zhengliu7194 5 ปีที่แล้ว +2

    excellent work, very helpful! thank you!

  • @MrTrescojones
    @MrTrescojones 7 ปีที่แล้ว +1

    thanks very useful. People's comments can overlook the background information that gives the keys to a technology or process,but this is pretty thorough.

    • @ClaytonBridges
      @ClaytonBridges  7 ปีที่แล้ว

      Thanks I appreciate that. I just wanted to go slightly in depth, the kind of stuff you might want to see before you get into such a thing

  • @peterford9369
    @peterford9369 2 ปีที่แล้ว

    Seem s redundant to have to ruff up something your going to melt together. When you're basically mixing the two surfaces. You're not adherring two surfaces face to face.
    It sounds cool but seems practice is definitely necessary. I've tried so many times over the years to weld plastic but heat is definitely the trick. Too hot and u change the molecular structure and your project is too brittle. To cold and they stick together at the surface but don't meld together. I'm attempting some radiator repair and if you screw up, a bigger hole or thin fix. That's why I was curious about this hot air type. Never seen that before. Interesting. Thanks

  • @twistedtuned4273
    @twistedtuned4273 3 ปีที่แล้ว

    gotta have everything to do it

  • @chicken133221
    @chicken133221 4 ปีที่แล้ว +1

    I want to learn about this plastic weld. Thinking making toggle switch brackets

    • @ClaytonBridges
      @ClaytonBridges  4 ปีที่แล้ว +1

      Its fun, find a better tutorial though 🤣🤣

    • @chicken133221
      @chicken133221 4 ปีที่แล้ว +1

      @@ClaytonBridges don't know what one to buy

  • @Subfightr
    @Subfightr 4 ปีที่แล้ว +6

    "we're going to be using, the pp" te he he

  • @travisguy6044
    @travisguy6044 4 ปีที่แล้ว +2

    Hey same music as tiny off grid house guy lol anyway good video very informative...

  • @SP-mp9yi
    @SP-mp9yi 3 ปีที่แล้ว

    Awesome video thanks

  • @herbertstolz1097
    @herbertstolz1097 2 ปีที่แล้ว +1

    Could you tell me where you bought your plastic welder from and the Rods too.

    • @ClaytonBridges
      @ClaytonBridges  2 ปีที่แล้ว

      I purchased it at harbor freight. Chances are you can find them online. The rods were from HF too, Im sure you can find them online as well

  •  6 ปีที่แล้ว +6

    Nice try dude but people can be pretty harsh so if your new to something you need to lay it out letting folks know. Most will cut you some slack. I've never used a plastic welder but I've been a professional welder for 40 years and if that weld is normal for a plastic weld, I'll stick with glue. There isn't any fusing of the three surfaces to make one continuous piece. All it did was melt enough to stick the surface of everything together and just a little bit at that. Plastic welding is good but like metal welding because of the heat used it's limited to where it should be used. Even if it doesn't sound like it, I'm trying to help. Take it for what it's worth .

  • @georgeman948
    @georgeman948 3 ปีที่แล้ว

    Nice work

  • @andrewpendleton726
    @andrewpendleton726 ปีที่แล้ว

    You said to use a high grit sandpaper. Just commenting to those that do not know the higher the number the finer the grit.

  • @EstebanMenchacaGamboa
    @EstebanMenchacaGamboa 6 ปีที่แล้ว +1

    Helpful, thanks m8!

  • @LostInAce
    @LostInAce 5 ปีที่แล้ว +2

    Dude. After 8 minutes of talk talk, the welding process begins. This was your 1st weld, wasn't it. Hah! Cool video, man. They'll get better. I got the information I was looking for thru this video. Thanks.

  • @soulmpowered
    @soulmpowered 4 ปีที่แล้ว +1

    i think this is a great way to weld plastic . Any thoughts on what type of PPE that you would use? Im pretty sure plastic is toxic . Stay safe.

  • @DrDaab
    @DrDaab 6 ปีที่แล้ว

    Terrifically informational. Thanks !

    • @sailingreco4909
      @sailingreco4909 5 ปีที่แล้ว

      Very sorry to tell you but he's doing it all wrong. Dont follow his instructions AT ALL

  • @robertk925
    @robertk925 6 ปีที่แล้ว

    The label shown at minute 2:40 is incorrect. PP is used in blow-molded products like bottles and other containers, is very chemical resistant, and is typically slightly transparent (milky) white. ABS is probably the most common plastic in the world and is used in telephones, keyboards, and household "hard" plastics and comes in every color imaginable. PVC is correct, but keep in mind that burning it (melting is ok, burning is not) produces chlorine gas, and when it combines with moisture in the air can create hydrochloric acid.

  • @derJackistweg
    @derJackistweg 4 ปีที่แล้ว +2

    Wrong way, if other professionals do it right:
    Do not follow the rod with the hot iron - follow the hot iron with the welding rod, heating both: The material and the welding rod, while pushing the rod into the material.

  • @charleslane2735
    @charleslane2735 ปีที่แล้ว

    I cant seem to find the air compressor style plastic welders.

    • @ClaytonBridges
      @ClaytonBridges  ปีที่แล้ว

      Hmm at harbor freight? They may be available online. I know at harbor freight theyre tucked away a little bit. Like bottom shelf on the floor in the welding section. Im not sure where else

  • @rodjos5463
    @rodjos5463 2 ปีที่แล้ว +1

    Wear gloves ➡️ No gloves while working

  • @PaulA-ky6bv
    @PaulA-ky6bv 2 ปีที่แล้ว +1

    What about polymer pistol frames?

    • @ClaytonBridges
      @ClaytonBridges  2 ปีที่แล้ว

      Well you can most certainly use it to get that texture. Surely it gets hot enough.
      HOWEVER I don't know anything about stipling pistols. You want to make sure you're doing it properly (however that is) especially considering its a weapon that could make or break situations.
      But im sure it could get hot enough to stiple plastic like that. But I would think you'd be better off just getting a soldering iron

    • @PaulA-ky6bv
      @PaulA-ky6bv 2 ปีที่แล้ว

      I was more referring to adding material rather than stippling

  • @johnjeff3849
    @johnjeff3849 5 ปีที่แล้ว +1

    Hey Clayton, now you have taught yourself to weld plastic, how about a short course in shooting video?

    • @ClaytonBridges
      @ClaytonBridges  5 ปีที่แล้ว +1

      Well you can check out my new content if you like! I think It's improved in quality quite a bit. Not to mention its more accurate. I still don't have a fancy camera or microphone however

  • @hatsunemikussnzbmindcontro4444
    @hatsunemikussnzbmindcontro4444 5 ปีที่แล้ว

    Only Limited by my imagination 😱🌈🦙🦄
    Need to have That thing and alot of plastic 😛 thx !

  • @kildaz91
    @kildaz91 2 ปีที่แล้ว

    Just wondering,why my plastic abs rods doesn't melt?

    • @ClaytonBridges
      @ClaytonBridges  2 ปีที่แล้ว

      Hmmm I think ABS is a pretty high melting point, about 400 degrees, is it possible you arent getting it hot enough?

  • @DannyRossa
    @DannyRossa 4 ปีที่แล้ว +1

    175,000 views not bad...

  • @dreamingrightnow1174
    @dreamingrightnow1174 6 ปีที่แล้ว +5

    Wow, tough crowd. I learned a couple things, but I'm just another grateful dummy, lol.

  • @shoegod2311
    @shoegod2311 7 ปีที่แล้ว

    Which Rod would I use for welding Automotive plastic intakes

    • @obfuscated3090
      @obfuscated3090 7 ปีที่แล้ว

      You need to find the identification symbol for what it's made of on the intake if that was included, or practice with different fillers on scrap intakes.
      TH-cam videos are nice but for that application professional info is needed and there's no substitute for doing your homework. Google "resin identification codes" and "plastic recycling codes".
      en.wikipedia.org/wiki/Recycling_codes
      Once you know the material you can order the correct filler rod. Plastic welding is very much like other welding. You should clean your weld area to remove all oil or grease and on an intake I'd use a Dremel to groove the joint before welding for greater strength.
      My wife used to do custom sportbike fairings and add air scoops, blend tail lights etc. It's easy and of course you can do automobile body parts. Their symbols are on the inboard side of the part.

  • @alikasim9627
    @alikasim9627 5 ปีที่แล้ว +1

    Hi i solder plastic repair with soldering iron. What filter type should i use that can store the dangerous fumes from going out in the environment?

  • @manzam01
    @manzam01 7 ปีที่แล้ว +2

    Hey Darth Vader, those blue cheap bins do not last long under UV light,I would recommend using some kind of UV paint protection if sunlight reaches the plastics

    • @ClaytonBridges
      @ClaytonBridges  7 ปีที่แล้ว +1

      the piece I used it for is under a hood its entire life

  • @localgamerz2961
    @localgamerz2961 7 ปีที่แล้ว +2

    ive done this with a old flat head screw driver and a torch lmao

    • @ClaytonBridges
      @ClaytonBridges  7 ปีที่แล้ว

      melting plastic isnt the hardest task man has been challenged with. your torch requires fuel, this doesnt really

    • @ClaytonBridges
      @ClaytonBridges  7 ปีที่แล้ว

      a torch will burn the plastic as well

    • @sailingreco4909
      @sailingreco4909 5 ปีที่แล้ว

      @Weaver Cattle Company You actually can do it dude. I am welding plastics for 20 years (not like this guy, obviously) and I hv repaired hundreds of gasoline tanks. But I am not going to tell you how......use your imagination.... And one more thing. If you wanna do it properly, use a LEISTER gun. They are the expensive but the best from far.

  • @dandahermitseals5582
    @dandahermitseals5582 4 ปีที่แล้ว +1

    So it's just another fusion method like brazing, just different material.

    • @Nick-rz4zj
      @Nick-rz4zj 4 ปีที่แล้ว +1

      Yes but no where near as good lol

  • @thecowconspiracy1587
    @thecowconspiracy1587 6 ปีที่แล้ว +2

    Tin snips for straight even cuts, regular sander with 80 grit paper then 120 so surface is rough but flat and quality plastics are always recommended dead when fixing water tanks or gas cans, wash and dry all bits off roughened plastic first and TRY TO USE SAME TYPE OF PLASTIC! The blue plastic on the headlight fix was a poor match. Hard plastic to hard plastic, don’t patch over but match edges and seam....my survival instructor in the Army always said, “practice does NOT make perfect! But PERFECT PRACTICE makes perfect!”

    • @donaldellis9004
      @donaldellis9004 6 ปีที่แล้ว

      The Cow Conspiracy like spelling lol, I had to sorry, but I am about to post that comment I like that.

    • @manp1039
      @manp1039 6 ปีที่แล้ว

      what kind of plastic do you think was being repaired on the light cover? And i am wondering how to identify that.. I wonder if that too had a recycle label molded into and hidden somewhere on it.

    • @avid0g
      @avid0g 5 ปีที่แล้ว

      @@manp1039
      Even when there is no recycling symbol on a part, the plastic code letters are usually somewhere on it. The code letters are also just outside the recycling symbol, if present.
      Additional letters indicate composite filler material like glass fibre or glass ball (micro-sized).

    • @SanjayYadav-ft7xs
      @SanjayYadav-ft7xs 3 ปีที่แล้ว

      Sir what is the name of this machine

  • @AvocaSingleTrack
    @AvocaSingleTrack 4 ปีที่แล้ว +1

    you gotta get it lubricated, then shove the tip in .....

  • @jacquesjones5570
    @jacquesjones5570 4 ปีที่แล้ว

    sorry harbor freigt dose not sell this any more i wase thereon jan 24 2020

  • @18magicMARKer
    @18magicMARKer 4 ปีที่แล้ว +1

    2017... looks like it was shot with a 2007 camera phone

  • @fredflintstone2077
    @fredflintstone2077 6 ปีที่แล้ว +5

    Hey mate, you need some practice!

  • @reviewerman9786
    @reviewerman9786 7 ปีที่แล้ว +2

    Buying plastic to practice on? Just walk/drive around on trash day. Or if you live by a college campus go by during move in/move out.

    • @ClaytonBridges
      @ClaytonBridges  7 ปีที่แล้ว

      I have a bucket full of plastic scrap, I just needed specific shapes to do a few things.

    • @putster47
      @putster47 6 ปีที่แล้ว

      My thought exactly! You can't go down the street without seeing something plastic along the side of the road. I thought the whole purpose of fixing something was to save money lol

  • @mikesolarz1561
    @mikesolarz1561 6 ปีที่แล้ว +1

    Or you could have put a drop of automotive black silicone into the hole. 3 second fix.

  • @robertbutler8004
    @robertbutler8004 6 ปีที่แล้ว +6

    Not even close to being welded.

  • @D.anielZzz
    @D.anielZzz 4 ปีที่แล้ว +1

    Are you gonna do it by yourself?

  • @geezer4444
    @geezer4444 3 ปีที่แล้ว

    Expensive glue gun

  • @TheBrentfleming
    @TheBrentfleming 6 ปีที่แล้ว +1

    hot knife works better and cheaper

  • @you-tubejunkie2926
    @you-tubejunkie2926 6 ปีที่แล้ว +2

    Keep shaking it. So I can't read it Beaver.

    • @rockymontana1
      @rockymontana1 6 ปีที่แล้ว

      I wonder why Wally wasn't their,Ohhh maybe he was doing the camera....

  • @TRX450RVlogger
    @TRX450RVlogger 6 ปีที่แล้ว +1

    I like the PP

    • @rockymontana1
      @rockymontana1 6 ปีที่แล้ว

      I like the PP TOO.....lmfao......

  • @davidhunt5699
    @davidhunt5699 3 ปีที่แล้ว +1

    hold the damn camera still!!!!!!!

  • @rockymontana1
    @rockymontana1 6 ปีที่แล้ว +1

    What about GLUE? Did people forget GLUE? plastic welding is nice but what about GLUE?

    • @rockymontana1
      @rockymontana1 6 ปีที่แล้ว

      Do you know what a J O k E is ??????????It sure don't seem that you do...I can't believe their are so many of you that have no clue what a joke is,the only reason for that is you are more than likely just a kid and don't know ....

    • @drizler
      @drizler 6 ปีที่แล้ว +2

      Ahhhh but that’s the nature of the internet....... some of what you say can be easily taken wrong. Always proof read......always!

    • @ellinasmarios6165
      @ellinasmarios6165 2 ปีที่แล้ว

      Although glue seems obvious choice most plastics don't form strong bonds with glues

  • @danpettis1675
    @danpettis1675 7 ปีที่แล้ว

    Looks like blue bear from American hot rod

  • @johnmcadden3404
    @johnmcadden3404 7 ปีที่แล้ว

    This guy reminds me of a young Jeremy Renner

    • @ClaytonBridges
      @ClaytonBridges  7 ปีที่แล้ว

      Thats alot better than Blue Bear from American Hot Rod hahaha.

  • @lmandsons
    @lmandsons 6 ปีที่แล้ว +2

    totally wrong

  • @MrLibbyloulou
    @MrLibbyloulou 6 ปีที่แล้ว +8

    what a very poor show...that's how not to weld plastic

    • @rockymontana1
      @rockymontana1 6 ปีที่แล้ว

      like I said what about GLUE? lmfao....

  • @clyde8759
    @clyde8759 7 ปีที่แล้ว

    I'll stick to metal

    • @chooowie
      @chooowie 6 ปีที่แล้ว

      Nice sx at the end😀

  • @simonlang2001
    @simonlang2001 6 ปีที่แล้ว

    you did not go through cool down process, of startup, This being Harbor Frought, it would run like this bring air on line, then turn up heat, then for cool off turn of heat, keep air on, but good enough.

  • @paulcarter2907
    @paulcarter2907 6 ปีที่แล้ว

    GOOD INFO, BUT TOO MUCH, MOST WHO WOULD WATCH THIS KNOW MOST, SO TEACHING US TO SUCK EGGS..BUT..GREAT EFFORT AND THANK YOU...

  • @RogerBFC
    @RogerBFC 6 ปีที่แล้ว +2

    Simply useless

  • @headsup65
    @headsup65 4 ปีที่แล้ว +1

    you're getting there Matey you really need more practice before you try to show how to plastic weld Really dude PRACTICE MORE!!!!

  • @dellam04
    @dellam04 4 ปีที่แล้ว

    I bet that your welds don't bond well if you test it. You cannot weld plastic without nitrogen...

  • @makingbakersfieldgreatagai9203
    @makingbakersfieldgreatagai9203 7 ปีที่แล้ว

    🤔 how about don't drill holes in you car...

  • @freddyo2k10
    @freddyo2k10 6 ปีที่แล้ว +1

    That's crooked ass welding..pffft👎

  • @georgeschmid1862
    @georgeschmid1862 6 ปีที่แล้ว +2

    yea, you talk too much

  • @jimbob6048
    @jimbob6048 4 ปีที่แล้ว

    Terrible....wasted my time

    • @ClaytonBridges
      @ClaytonBridges  4 ปีที่แล้ว

      Im sorry, I made this a long time ago, and I agree, not very quality.

  • @beczkalo7
    @beczkalo7 4 ปีที่แล้ว

    Stick to the video games bro

  • @Kane-ib5sn
    @Kane-ib5sn 2 ปีที่แล้ว

    you know, this is a total f'k up video?...just try doing it, see what happens...

    • @ClaytonBridges
      @ClaytonBridges  2 ปีที่แล้ว

      Ive made that abundantly clear in the pinned comment and my description.
      The dislike button used to reflect that, but guess what, youtube removed it.