1ch - aileron1, 2ch - elevator, 3ch - esc with motor and battery, 4ch - ruder, 5ch - aileron2. but in transmitter setting you need to setup flaperons for aileron2 working, or use a Y servo lead
@Ixtocaltro I consider the best value on the market today. It's a good radio with a great price. ($ 60 for a 9-channel radio). It is the best radio in the world? No, but radio is a lot better than the price might make you think. I have two.
Great video. Thanks for clearing that up. Next question: Which channel is set to Rudder, Throttle, Ailerons and Elevator on the receiver, after it is binded?
@tompuch49 You dont really need this battery. Just plug in your ESC to channel 3, your bind plug on channel 9 and connect your battery to your ESC, does the same thing.
I have received this earlier this week and it was working fine until the throttle just stopped working. After I turn off the receiver, I have to re-bind it every time. Is there a fix to this? or do you think it is just a bad receiver.
@tompuch49 Battery packs from 5V to 6V with the appropriate connector to the receiver and with great attention to polarity. What would you use battery pack to power a receiver in a model airplane powered combustion engine? It is the same. Check on your favorite hobby shop.
I just received mine. I don't recall seeing a channel 9 or 10 on the receiver. I believe mine just had 8 channels plus the battery. Hey is that the Hobbyking cutting mat?
OK...got two receivers 'bound'. The elevator, aileron and rudder channels respond to the Transmitter, but the throttle does nothing. I am able to run the same motor when I connect another known to be working ESC as long as I use my old Dynam receiver and TX. Is there some trick to getting the throttle to work with the T9X??
I bought one of these also came with ELEV and channel problem, a great sensitivity in stik. Still not sure how to solve, including the programming and I tried did not work, I think it might be the potentiometer, you have idea how to solve this? Thank you.
Thanks for the video! Noticed that on the V2, Bind is printed above Channel 10 and Bat is on Channel 9. Is this just really bad usability/design? how did you discover that Channel 9 was Bind and Channel 10 was batt?
im so confused...the sticker on your receiver says that the bind should be in channel 10 and the battery should be connected to channel 9...but you put the bind chord in 9 and the battery in 10.....why do you do that?
I bound the receiver to the remote as said/shown and it responded just as in the video. Once i plug the servo in the first channel and turn both receiver and remote the servo acts weird and is moving the axis back and forth. A person i know plugged it into his receiver and it worked normally. No idea what I'm doing wrong.
I'd never had guessed it worked that way. Great vid, great soundtrack, too.
muito bom!dindei o meu seguindo suas orientações.muito prático.obrigado!
1ch - aileron1, 2ch - elevator, 3ch - esc with motor and battery, 4ch - ruder,
5ch - aileron2. but in transmitter setting you need to setup flaperons for aileron2 working, or use a Y servo lead
Danke für das gut verständliche Video!...hat mir sehr geholfen.
@Ixtocaltro I consider the best value on the market today. It's a good radio with a great price. ($ 60 for a 9-channel radio). It is the best radio in the world? No, but radio is a lot better than the price might make you think. I have two.
Great video. Thanks for clearing that up. Next question: Which channel is set to Rudder, Throttle, Ailerons and Elevator on the receiver, after it is binded?
@tompuch49 You dont really need this battery. Just plug in your ESC to channel 3, your bind plug on channel 9 and connect your battery to your ESC, does the same thing.
I received mine today! very satisfied
Thanks so much. It worked. I was so desperate for help.
Sweet music and great video! Thanks.
I have received this earlier this week and it was working fine until the throttle just stopped working. After I turn off the receiver, I have to re-bind it every time. Is there a fix to this? or do you think it is just a bad receiver.
@Athensbashing Good news!
@yumaokamoto Hard to say, it can even be electrical power problem
Great JOB, simple and easy
@tompuch49 Battery packs from 5V to 6V with the appropriate connector to the receiver and with great attention to polarity. What would you use battery pack to power a receiver in a model airplane powered combustion engine? It is the same.
Check on your favorite hobby shop.
Does the plug bind come in the turnigy 9x kit from hobby king? can i use a bind plug from a hobby king 6channel v2?
muito bom.me ajudou muito.
@TheJulianobatera
Welcome.
I just received mine. I don't recall seeing a channel 9 or 10 on the receiver. I believe mine just had 8 channels plus the battery.
Hey is that the Hobbyking cutting mat?
How good is that Tx and Rx, do you recommend it? Thanks for your comments.
OK...got two receivers 'bound'. The elevator, aileron and rudder channels respond to the Transmitter, but the throttle does nothing. I am able to run the same motor when I connect another known to be working ESC as long as I use my old Dynam receiver and TX. Is there some trick to getting the throttle to work with the T9X??
I bought one of these also came with ELEV and channel problem, a great sensitivity in stik. Still not sure how to solve, including the programming and I tried did not work, I think it might be the potentiometer, you have idea how to solve this? Thank you.
Will the receiver pack be included or is it needed to be bought?
Very helpfull, thanks a lot for sharing...
@pustagrilla
Welcome, disponha.
Thanks for the video!
Noticed that on the V2, Bind is printed above Channel 10 and Bat is on Channel 9.
Is this just really bad usability/design?
how did you discover that Channel 9 was Bind and Channel 10 was batt?
@frankynathanael Thank you.
I want to use two receivers simultaneously. Can I bind the Turnigy 9x to two receivers?
I'd like to use two receivers simultaneously. Can I bind one Turnigy 9X transmitter to the two receivers?
is it a Tag Heuer F1 ?
Usefull vid by the way !!
only works with this receiver or work also with some FBL systems? like 3gx?!
Thanks for help!
thank you it was realy helpful.
thx
@mupsilaama It restarts the cycle of channels.
Cheers for the video, it helped me out thanks! :)
Thanks bud. Works perfect.
im so confused...the sticker on your receiver says that the bind should be in channel 10 and the battery should be connected to channel 9...but you put the bind chord in 9 and the battery in 10.....why do you do that?
good video
thanks, you help me
@frozentrone31 Disponha.
I bound the receiver to the remote as said/shown and it responded just as in the video. Once i plug the servo in the first channel and turn both receiver and remote the servo acts weird and is moving the axis back and forth. A person i know plugged it into his receiver and it worked normally. No idea what I'm doing wrong.
they are labeled