Thank you, I was actually counting the turns as you went to a 12-inch dept cut, now this video is to my favorite and watch later, I'm going to wear it out.
Seems rather odd that the horizontal sizing dial couldn't be made larger so it wouldn't have to go around twice to get your 8" or 10" desired cut. I get that you usually only cutting 2 to 4 inches thick at a time. What is the kerf of the saw blades? It looks huge when you see the offset amount on the sizing dial.
Yeah, I dont mind the dial being only 4 inches per rotation, I think it has to do with the gearing, runs with sprockets and heavy chain. Kerf is .322 inches I believe, I forget the exact number on the teeth. I tried narrower teeth once but the blade ends up getting hot and cutting really bad.
I think it's better this way; if they made the dial register twice as much distance, you'd either have to make it physically bigger, or you'd lose some of your precision...
I haven't needed any repairs so far, but yes I talk to them lots and there's no problem getting parts or support. I saw a mill they were doing a repair on, installing a new sawdust chute after 6000 hours. The drive train was still in really great condition.
That's great to hear! 6000 hours, wow! What a testament of the build quality of Mahoe mills! Hope one day to purchase one. Do you think it is worth paying extra for the Supermill, with hydraulics, compared to the Minimax? Not much horsepower increase and seems the hydraulics are minimal, though helpful. @@SharpeTimber
Thank you, I was actually counting the turns as you went to a 12-inch dept cut, now this video is to my favorite and watch later, I'm going to wear it out.
Glad you enjoying it!
Does one need to check blade overheating on deep cuts? Fantastic video!
Not usually, I run water on the blade which keeps it cool. It can overheat possibly if you get pinched bad.
Pretty sweet machine!
Thanks!
I like how that saw goes&brings back a board-seems efficient compared to bandsaw/edger setup-who is bald head guy?
Yes its really easy on the operator and efficient with my time. Thats my dad.
What are the largest cuts you can make? I'm sure it's just less than half the diameter of the blades, but I don't know that either.
I can cut 8x12s, 8 inches on the horizontal blade and 12 deep on the vertical.
Do you do anything with the sawdust? Like make wood pellets for stoves?
Not really, I have thought about making a pellet maker before. Would be a good use for it.
🎉🎉🎉🎉
😁👍
This mill, what is the longest piece you can saw in it?
Total is 7m long, so about 23 ft.
Olá bom dia! Da pra levar essa máquina para o floresta e monta
Seems rather odd that the horizontal sizing dial couldn't be made larger so it wouldn't have to go around twice to get your 8" or 10" desired cut. I get that you usually only cutting 2 to 4 inches thick at a time. What is the kerf of the saw blades? It looks huge when you see the offset amount on the sizing dial.
Yeah, I dont mind the dial being only 4 inches per rotation, I think it has to do with the gearing, runs with sprockets and heavy chain. Kerf is .322 inches I believe, I forget the exact number on the teeth. I tried narrower teeth once but the blade ends up getting hot and cutting really bad.
I think it's better this way; if they made the dial register twice as much distance, you'd either have to make it physically bigger, or you'd lose some of your precision...
Good question and information. How often do you change out blades? @@Tasarran
What do you do if you need repairs? Will NZ Mahoe take your call and give support, sent parts?
I haven't needed any repairs so far, but yes I talk to them lots and there's no problem getting parts or support. I saw a mill they were doing a repair on, installing a new sawdust chute after 6000 hours. The drive train was still in really great condition.
That's great to hear! 6000 hours, wow! What a testament of the build quality of Mahoe mills! Hope one day to purchase one. Do you think it is worth paying extra for the Supermill, with hydraulics, compared to the Minimax? Not much horsepower increase and seems the hydraulics are minimal, though helpful. @@SharpeTimber
My new LT 40 has broken down 4 times in 68 hours . Last time 4 weeks waiting for parts. I’ve ordered a super mill now.
How much is this mill
Exactly. I also wonder what the list price is on those.
I paid around $45k Canadian after it was shipped here and import tax.
Bom qual valor dessa serraria
Looks like you. have the easy part of the job while your wife is busting her butt (I have run a mill for years and know there is no easy part.
Yes it is more work to unload the mill. This is my sister helping me out. She's a very good worker👍