Wow, almost everything is dissambled. These engines are great tho , have an audi a3 2008 with the same one. Never had any issues. Did the timing belt and waterpump recently. Clutch is starting to feel soft , so i got to your video. Seems a BIG JOB wow !
No, unfortunately... In order to dismount the transmission you need to unscrew the passenger's side output shaft "cup" (the thing at 6:08), thus oil would leak.
Hi, thank you. Back then I was using 24L Nuair 1,5kW single piston compressor - basically the smallest and the cheapest compressor. It worked great for impact wrench, die grinder, air hammer, and even for hvlp spray gun. Now I've got 100L Agre twin piston, because I wanted to do sandblasting.
@@benjaminmarcinek thanks for the reply, im in the search for a compressor currently, based in your comment i think 200l is just overkill, as im not going to use it extensively, i actually bought an air hammer first 😂 so does your current 100l compressor works flawlessly with that sandblaster? I know those consume plenty of air.
Very good video - thanks! The only thing that goes a bit fast is how you lifted the engine with bridge and supported the gear box with a chain when you were under it. I would have found it even more helpful if this was clearer in the video - for those of us with less experience like me, this is a challenge or at least makes me quite cautious. You seem to have undone only one engine mount (the gearbox side)...?
Hi, thank you, yes I removed only one engine mount. I supported the engine with the bridge and the bottle jack (just to be sure). I chained the gearbox to the bridge just so it wouldn't fall on me, because I didn't know how heavy it was. After I realised it's quite light, I grabbed it by hand while another person removed the chain from the bridge.
After watching your video and seeing how much work, messing about and all of the intricacy I have decided to sell my van and buy another new car. Now, who wants parts? I will drive it to the Auto-wreckers this afternoon rather than do all of this work.
Neviem presne, ale ja si myslim ze vazi okolo 30kg. Ak som to zvladol ja, tak to zvladne kazdy :D Retaz tam bola iba pre istotu, zaviazal som ju o stojan na odvesenie motora. Vdaka za zhladnutie, vela stastia.
Das Getriebe ist nicht in Waage verbaut, so das der richtige Ölstand über der Einfüllschraube liegt. VW schreibt vor das Getriebe von oben (Durch den Rückwertsgangschalter) mit der passenden Menge zu befüllen. Dafür muss eigentlich auch unten noch die Welle für den Schalthebel gezogen werden um das Öl vollständig abzulasen. Dieser muss oben fixiert werden da er sonst nicht in Position bleibt. Normal muss das Öl aber nicht abgelassen werden um das Getriebe auszubauen. Ich hatte den Antriebswelenflansch allerdings ausgebaut damit es besser rausgeht, dann kommt leider das Öl raus :-)
Hi, I was following the "VW Caddy (2K) - 5-speed manual gearbox 0A4" workshop manual, there are all of the torque specs, you can find the manual online for free.
Passat cc 2008....mi servirebbe la stretta dei bulloni in Nm....parlo di tutti bulloni de la macchina...non riesco a trovare....grazie per le risposte anteriore
Maschine💪🏼 muss bei mir jetzt auch ran, hab jedoch großen Respekt das Getriebe da allein rauszuheben auf dem Boden😃
Thank you ❤ but it wasn't that bad, the gearbox isn't very heavy
Wow, almost everything is dissambled. These engines are great tho , have an audi a3 2008 with the same one. Never had any issues. Did the timing belt and waterpump recently. Clutch is starting to feel soft , so i got to your video. Seems a BIG JOB wow !
Before start this job,ideal îs to wash gearbox and engine very good😉 Good bles You!
Yeah you're right, lesson learned. Thanks for the tip 👍
Köszönöm ezt a videót!
Good video. Why you dont change the crankshaft seal?
The clutch cannot be changed without drain the gearbox oil?
No, unfortunately... In order to dismount the transmission you need to unscrew the passenger's side output shaft "cup" (the thing at 6:08), thus oil would leak.
Clean and professional work. Hey man, one question, what air compressor do you use? Is it enough for every air tool do you use?
Hi, thank you. Back then I was using 24L Nuair 1,5kW single piston compressor - basically the smallest and the cheapest compressor. It worked great for impact wrench, die grinder, air hammer, and even for hvlp spray gun. Now I've got 100L Agre twin piston, because I wanted to do sandblasting.
@@benjaminmarcinek thanks for the reply, im in the search for a compressor currently, based in your comment i think 200l is just overkill, as im not going to use it extensively, i actually bought an air hammer first 😂 so does your current 100l compressor works flawlessly with that sandblaster? I know those consume plenty of air.
@@RGV2300 yeah it works well with my handheld gun.
Mit hebebühne hättest du das mit einer hand gemacht, super arbeit👍
Danke Mann. 👍
Respekt, grossartige Arbeit! Kann ich meinen Caddy vorbeibringen, da ist das Ausrücklager defekt?
Toto je predsa jednohmotny zotrvak nemal by byt 2hmotny ?? Alebo je nahodena prestavba
Vsetko stock, montovali sa aj aj, je to v technickych manualoch. Je to totiz najslabsia 55kw verzia, tak je tam jednohmota.
Very good video - thanks! The only thing that goes a bit fast is how you lifted the engine with bridge and supported the gear box with a chain when you were under it. I would have found it even more helpful if this was clearer in the video - for those of us with less experience like me, this is a challenge or at least makes me quite cautious. You seem to have undone only one engine mount (the gearbox side)...?
Hi, thank you, yes I removed only one engine mount. I supported the engine with the bridge and the bottle jack (just to be sure). I chained the gearbox to the bridge just so it wouldn't fall on me, because I didn't know how heavy it was. After I realised it's quite light, I grabbed it by hand while another person removed the chain from the bridge.
Combien de temps pour changement kit embrayage toran ??
Why replace the crank sensor? Was it faulty or just renew it while your there?
Thanks for the comment. It was in fact faulty, intermittent loss of signal. More info is in the description.
After watching your video and seeing how much work, messing about and all of the intricacy I have decided to sell my van and buy another new car. Now, who wants parts? I will drive it to the Auto-wreckers this afternoon rather than do all of this work.
How long did it take you to do in total?
Good job :)
Dude your a beast
Thank you
What is the engine code? I need info for BXE clutch
Single mass flywheel?
Yeah, you're right
Please tell me, what is madel and year of van please?? As you have solid flywheel, I would like this in my van…. Thanks
It's Volkswagen Caddy Life, 2007 with 1.9TDI 55kW "BSU" engine
I switched from auto to manual do u use back plat and shims ?
There was a factory supplied backplate it stayed on the engine block side, I didn't even remove it.
EL DISCO NO ESTABA AL REVES???
El lado plano siempre enfrenta al volante de inercia. De todas formas, si lo fueses a poner al revés no encajaría bien.
Koľko váži táto prevodovka? Dokáže to jeden stredne silný človek bezpečne? Držala túto reťaz iná osoba na podporu? Pozdrav z Poľska.
Neviem presne, ale ja si myslim ze vazi okolo 30kg. Ak som to zvladol ja, tak to zvladne kazdy :D Retaz tam bola iba pre istotu, zaviazal som ju o stojan na odvesenie motora. Vdaka za zhladnutie, vela stastia.
Das Getriebe ist nicht in Waage verbaut, so das der richtige Ölstand über der Einfüllschraube liegt. VW schreibt vor das Getriebe von oben (Durch den Rückwertsgangschalter) mit der passenden Menge zu befüllen. Dafür muss eigentlich auch unten noch die Welle für den Schalthebel gezogen werden um das Öl vollständig abzulasen. Dieser muss oben fixiert werden da er sonst nicht in Position bleibt. Normal muss das Öl aber nicht abgelassen werden um das Getriebe auszubauen. Ich hatte den Antriebswelenflansch allerdings ausgebaut damit es besser rausgeht, dann kommt leider das Öl raus :-)
You actually made it look too easy
Thanks, but it was actually my first time doing it
Też ostatnio robili sam w audi a3 8L 1.9 130km
Good
👏👏👏❤
👍
Nm?????
Hi, I was following the "VW Caddy (2K) - 5-speed manual gearbox 0A4" workshop manual, there are all of the torque specs, you can find the manual online for free.
Where find manual????
@@florinmunteanu1670 I found mine here: cardiagn.com/vw-caddy-2k-5-speed-manual-gearbox-0a4/
Passat cc 2008....mi servirebbe la stretta dei bulloni in Nm....parlo di tutti bulloni de la macchina...non riesco a trovare....grazie per le risposte anteriore
Passat cc 2008 cbab 103kw 140cp 357
🎖️🎖️🎖️🎖️🎖️🎖️🎖️🎖️🎖️🎖️🎖️