So what is the benefit of a “race plug”. Other than constant rail pressure? What is the the biggest problem with a consistent high pressure? It’s not a water heater or boiler that will shoot like a rocket. Will it harm the motor?
Please exercise caution if purchasing from this store, as it is part of an AI generated network of stores selling drop-shipped products. The products may be priced higher than normal, be unfit for purpose and/or may not be shipped at all
We've been selling race plugs for all types of HP levels and have NEVER had an issue or call back regarding pressure spikes. If a component in your fuel system can't handle that spike of pressure, it was going to fail any ways.
@@DieselPowerProducts 😆 A "pressure relief valve" - used to relieve pressure. Block off a pressure relief valve - pressure has no where to go. Somethings gotta give. Would you block off a pressure relief valve on a boiler or hot water heater? What could/would happen if you did? Blocking off relief on a hugh pressure fuel system that has ~30,000psi of rail pressure = stupid.
I agree, you understand pressure dynamics. However, there is a difference to what happens on paper, and what happens in practice of such. On paper, should it cause a huge problem all the time? Yes. In practice, does it? No, not even a little.
@@DieselPowerProducts That is just untrue. Not trying to be a dick. I'd just suggest maybe putting a disclaimer in the video, warning people about the risk of using block off plugs in a hugh pressure fuel system. This is not something you just want to throw on your motor, not realizing what you are actually doing, and the potential risks. The video comes off as just a "hey, buy this!"
We've sold them to people who have installed them on stock trucks, higher horsepower trucks, and between. In my 10 years with this company and multiple thousands sold, not a single customer called back with an over pressurization issue. I am not disagreeing with the principals of the fluid dynamics. I am however agreeing with real world experience. This video is not a "HEY BUY THIS." It is a comparison between the two with visual aids. We sell both and believe in both. If you don't want to put the plug on, then go with a high-quality Bosch replacement. Want as much rail pressure as possible and to remove a common failure point, get the plug.
I have a 2002 lb7. Lost fuel delivery one day, died, prime from tank to filter prime pump, pump it up, it starts quick , runs then after a bit dies,runs out of fuel. Install fass titanium 165 gph lift pump, runs now but at half throttle power falls off. No codes. Any thoughts...
So what is the benefit of a “race plug”. Other than constant rail pressure? What is the the biggest problem with a consistent high pressure? It’s not a water heater or boiler that will shoot like a rocket. Will it harm the motor?
My Common rail around pressure relief valve is very hot during engine works.
What's the cause and the solutions?
Suction line cracked in sender assembly, thank you brother,
Ive called 2 different auto parts store and they told me it was 300-400 dollars
Second 👊🏻💪🏻
Please exercise caution if purchasing from this store, as it is part of an AI generated network of stores selling drop-shipped products. The products may be priced higher than normal, be unfit for purpose and/or may not be shipped at all
Shouldn't be promoting these block off plugs. You know they aren't good for the fuel system.....
We've been selling race plugs for all types of HP levels and have NEVER had an issue or call back regarding pressure spikes. If a component in your fuel system can't handle that spike of pressure, it was going to fail any ways.
@@DieselPowerProducts 😆
A "pressure relief valve" - used to relieve pressure. Block off a pressure relief valve - pressure has no where to go. Somethings gotta give.
Would you block off a pressure relief valve on a boiler or hot water heater? What could/would happen if you did?
Blocking off relief on a hugh pressure fuel system that has ~30,000psi of rail pressure = stupid.
I agree, you understand pressure dynamics. However, there is a difference to what happens on paper, and what happens in practice of such.
On paper, should it cause a huge problem all the time? Yes.
In practice, does it? No, not even a little.
@@DieselPowerProducts That is just untrue.
Not trying to be a dick. I'd just suggest maybe putting a disclaimer in the video, warning people about the risk of using block off plugs in a hugh pressure fuel system. This is not something you just want to throw on your motor, not realizing what you are actually doing, and the potential risks. The video comes off as just a "hey, buy this!"
We've sold them to people who have installed them on stock trucks, higher horsepower trucks, and between. In my 10 years with this company and multiple thousands sold, not a single customer called back with an over pressurization issue.
I am not disagreeing with the principals of the fluid dynamics. I am however agreeing with real world experience.
This video is not a "HEY BUY THIS." It is a comparison between the two with visual aids. We sell both and believe in both. If you don't want to put the plug on, then go with a high-quality Bosch replacement. Want as much rail pressure as possible and to remove a common failure point, get the plug.
I have a 2002 lb7.
Lost fuel delivery one day, died, prime from tank to filter prime pump, pump it up, it starts quick , runs then after a bit dies,runs out of fuel. Install fass titanium 165 gph lift pump, runs now but at half throttle power falls off. No codes. Any thoughts...
Maybe a cracked or clogged fuel line bud . Sucking air somewhere or Clogged up line maybe . Did you ever figure it out ?