Agree with you on your cooling challenges and planned solutions 100% ! Every re-engineering design concept has it's challenges ! Without any challenges, there would be no reward !!! Great job with the project so far ! Merry Christmas !
A lot of modifying to be done. Is a neat idea. Definitely a better engine than the flat 6 that your Corvair originally came with. Wish you all the best!
I have been fascinated with the Corvair since a kid and the rear mounted V6 is always been an idea I tossed around. I thought side quarter panel scoops made sense and an aluminum V6.
I used to have a 64 Spyder although that doesn't mean I am an expert but I would put the radiator up front with louvers and exhaust the air down to leave trunk space. I would also up grade to a 1966 axle and transmission assembly as the 1966 transmissions were Saginaw using some the same gearing as front engine cars. I have worked on many Saginaws and they are a tough cheap transmission.
What a unique project car. Maybe a good inlet source of air is from the Right Hand Rear wheelhouse. Cut a square out of it. Build a Duct Funnel ? The 5.0 Mustang Renegade racers used to draw fresh air in from the Right front wheelhouse, no inner fenderwell like GM Cars have. Drilled cut out a 3 - 4 inch hole into the inner wheel area through thick Fenderwell Unibody, ran the aluminum tubing to and attached a K&N air filter. Disadvantage was filter got Road dirt on it driving but cool ambient High pressure air there driving. No hoodscoops or custom Ram Air design expense required. Still done that way 20 years later here Turbocharged LS GM Cars.
The original Brittish Mini which was front engine transversly mounted had a similar radiator arrangement with i mounted longitudly next to the engine. They got it to work, i am sure you can.
On a Chieftain tank the radiators sit above the engine under the top cover grill blows the heat out the top fans on the back/underside of the rads . They can be rotated to the vertical position with the cover off. Fit the rad under the hood.
they make cooler and fan on the corvairs that had ac you could get a ac condensor and t off the water going though that also and have a fan mounted on it where it would bring the air in from the hood without cutting the hood then you could run some duck work on the rad side and mount a small fan to bring more air in on that side with cutting anything this sure has been great to see you put that in there
Cool build I was thinking to do the same with 3.8 l67 in regards to your idea about the rad you need free air delivery for that to work well I would do like the fiero ans Mont in the front on a angle
If I could share a picture with you, I’d love to show you my neighbors, Hayabusa powered Corvair. It is ridiculous and very fast to transmissions the bike training and the car all in one.
The latest Electric fans are Brushless ball bearings equipped motors. Still pricey. That old Ford Crown Victoria Cop Car Electric Fan is a good one. C4 Corvette guys used for a while. Stock was crap on C4 Corvette. Some Dodge Intrepid electric fan guys used to talk about using also small and moved alot of CFM Air
I vaguely remember someone in the 60s adding a scoop just before the fender to bring cool air into the engine bay, like Ford did for the brakes on the mustang except these were the "NASA" style
After reading thru the comments, I'd think the shroud combined with your idea of walling off both ends of radiator 'should' work. IS it worth trying before cutting the decklid, possibly losing your sleeper edge??
I looked at this and did a little head scratching. Couldn't you leave the louvers the way they are and simply reverse the fans? Just blow the hot air out. Anyway, it's been fun watching the process.
por favor cuando ud adacto el motos v6 en el corvair , lo acoplo al tren de traccion original del corvair, quiero decir acoplo el motor v6 a la transmicion y a la caja original del corvair
Why not mount radiator under spare tire in trunk,hard pipe supply/ return back to engine . Electric fan blow down w/ air duct under front bumper ,out of sight
@@Raycr What $ range do you think a decent driver condition later 2 door might fetch? Wanting one of these! Dont want a major project nor a car thats too nice. Reliable, sorted. SoCal thanks!
@@gordocarbo Thank you. As for a price? I really don't have a good idea. Location often makes a big difference. Checking back yards will probably get you a better price than any advertised car
That's a really cool build/ project!!!👍Please check out my 1968 Barracuda fastback powered by a rowdy 512 stroker backed by an A833 4 speed manual. I think you'll approve. 👌
Pure antifreeze is way less efficient for cooling than antifreeze mixed with water. If you run pure antifreeze your engine will run warmer, not cooler.
@@nojunkwork5735 believe what you want, I tried in vain mixing it , it kept running hot until I went with straight antifreeze, doesn't antifreeze have a higher boiling point than water
Former radiator man here: 50/50 mix of water to antifreeze gives optimum cooling. Yes, antifreeze has a higher boiling point, but you don't want a coolant that absorbs more heat. It also loses heat slower than water. Can't say about your motorcycle, but it is not likely that it's running cooler no matter what your gauge says. For best results in any water cooled motor use distilled water. Captured rain water will do.
@@johnchandler1687 like I said I tried it like you pros said and it kept running hot so I did what I did and the light hasn't come on and the coolant hasn't come out your saying the very same thing the Suzuki people told me but it didn't work for my bike, my saying is whatever works as a matter of fact the fan hardly ever comes on, it's got to b really hot for it to Evan come on.
@@RaycrI have some questions about the Corvair the original engine in mine went out and was wondering if you would recommend the v6 swap and if you used the original transmission
@Isaac -sv7xt. It all depends on what you want out of your car. Do you want to just have a solid dayly driver? Do you want to increase proformance? You should evaluate what you want to end up with. The stock engine can be a good little power plant.
Nice job! You should make a similar dam on the driver's side. Then you could have a cold air intake on that side.
Lakewood side louvers would allow more air e try...
And yes a perimeter to radiator , and a fan shroud to help cooling...
Good work..!
Agree with you on your cooling challenges and planned solutions 100% !
Every re-engineering design concept has it's challenges !
Without any challenges, there would be no reward !!!
Great job with the project so far !
Merry Christmas !
Thank you hope your Christmas is merry. We hope to get back to the Corvair this spring
A lot of modifying to be done. Is a neat idea. Definitely a better engine than the flat 6 that your Corvair originally came with. Wish you all the best!
There was a lot of brain work on this one for sure! Thanks for watching
I like what you did with this. Very unique and creative. Made me wonder why I hadn’t seen one before?
There's a few around. There's a ramp side with a fuel injected 4.3, that install is very clean.
I have been fascinated with the Corvair since a kid and the rear mounted V6 is always been an idea I tossed around.
I thought side quarter panel scoops made sense and an aluminum V6.
imagine if gm kept the Corvair around and put the lf4 twin turbo v6 out of the Cadillac ATS in it. Turbo charged all aluminum v6 pushing like 450 hp.
Awesome 😎 you got this....If that is your farm you were cruising...Great place.... I like this project...
Thank you for watching! Yup, this is our place. I kinda have to live in the sticks with my habits. Lol
I would think matching air scoops or lovers in the rear quarter panels would go along way to giving more air
I used to have a 64 Spyder although that doesn't mean I am an expert but I would put the radiator up front with louvers and exhaust the air down to leave trunk space. I would also up grade to a 1966 axle and transmission assembly as the 1966 transmissions were Saginaw using some the same gearing as front engine cars. I have worked on many Saginaws and they are a tough cheap transmission.
What a neat challenge! Congratulations on the amazing engine swap. Liked, subbed and shared!
@@Journeyman-Fixit thank you. Now, let's see if I can finish it?
Congratulations that's so cool to see an old car back on the road again 🎉
Thanks I've already been in to the older cars
Well, the idea of opening the decklid/hood slightly was used with great success by FIAT on their ABARTH editions of the 500/600...
@@janfswedane Thanks, The problem with having the hood gaped in the front (hinged end) is that we need to get the air out of under the hood
interesting project for sure!
Thanks it's been an experience for sure
What a unique project car.
Maybe a good inlet source of air is from the Right Hand Rear wheelhouse. Cut a square out of it.
Build a Duct Funnel ?
The 5.0 Mustang Renegade racers used to draw fresh air in from the Right front wheelhouse, no inner fenderwell like GM Cars have. Drilled cut out a 3 - 4 inch hole into the inner wheel area through thick Fenderwell Unibody, ran the aluminum tubing to and attached a K&N air filter. Disadvantage was filter got Road dirt on it driving but cool ambient High pressure air there driving.
No hoodscoops or custom Ram Air design expense required.
Still done that way 20 years later here Turbocharged LS GM Cars.
Thanks, getting the intake air from the fender well wouldn't be a good idea since we live on a gravel road
@@Raycr Could maybe fit the present air filter in a box, like an Igloo. Run a fresh air pipe to it, from the tail pan of the Corvair?
@@brracing7861 that's a possibility, the battery will be relocated to the front and we'd have that space to do something with
The original Brittish Mini which was front engine transversly mounted had a similar radiator arrangement with i mounted longitudly next to the engine. They got it to work, i am sure you can.
On a Chieftain tank the radiators sit above the engine under the top cover grill blows the heat out the top fans on the back/underside of the rads . They can be rotated to the vertical position with the cover off.
Fit the rad under the hood.
they make cooler and fan on the corvairs that had ac you could get a ac condensor and t off the water going though that also and have a fan mounted on it where it would bring the air in from the hood without cutting the hood then you could run some duck work on the rad side and mount a small fan to bring more air in on that side with cutting anything this sure has been great to see you put that in there
Grreat installation ,im sure you'll work out the air flow issues. Shout out from the boyz in montreal
Thank you. I hope to get back to this project soon
Cool build I was thinking to do the same with 3.8 l67 in regards to your idea about the rad you need free air delivery for that to work well I would do like the fiero ans Mont in the front on a angle
Radiator in front venting under bumper no problem cooling
This is just too cool! (No pun intended).
Thanks, we kinda like it too. lol
If I could share a picture with you, I’d love to show you my neighbors, Hayabusa powered Corvair. It is ridiculous and very fast to transmissions the bike training and the car all in one.
Thanks! There is an email in the channel description if you'd like to send some pix
Oh I want this machine!
The latest Electric fans are Brushless ball bearings equipped motors. Still pricey. That old Ford Crown Victoria Cop Car Electric Fan is a good one. C4 Corvette guys used for a while. Stock was crap on C4 Corvette.
Some Dodge Intrepid electric fan guys used to talk about using also small and moved alot of CFM Air
We have to watch out for the depth of the fan assembly. There isn't much room
Looks good crammed in there. Maybe you can adjust your hinges to raise up the end of the lid and get a kind of a ram air effect in there
Thank you , we need to go the opposite way need to draw air out. I did think about propping the lid open some
Put a one inch deep shroud on the radiator and mount the fan on the shroud so you pull air through the whole surface of the radiator.
We're looking at a dual fan full shroud unit, a little trim to fit and it might be golden! Just need to watch out for the depth
I vaguely remember someone in the 60s adding a scoop just before the fender to bring cool air into the engine bay, like Ford did for the brakes on the mustang except these were the "NASA" style
NACA
Yenko Stinger
The American Porch Dinosaur! Lol😅
After reading thru the comments, I'd think the shroud combined with your idea of walling off both ends of radiator 'should' work.
IS it worth trying before cutting the decklid, possibly losing your sleeper edge??
I'm thinking that most wouldn't know the difference with more louvers. Corvair guys, on the other hand, would spot it across the parking lot! lol
Why not move the battery to the front so you can then have a fender well intake?
@@craigrendahl3718 that is the plan. Move a little weight around and build a cold air box
I looked at this and did a little head scratching. Couldn't you leave the louvers the way they are and simply reverse the fans? Just blow the hot air out. Anyway, it's been fun watching the process.
My thoughts were that we didn't want to draw the hot engine air across the radiator. Might not be a big deal but that's the reasoning for it
I would expect better than 70 mph easily!!!!
Sounds alot Like the original motor ...
Thank you for watching. It does keep the sleeper image going
Air is circulating around the radiator. Fix that and place a scoop or air inlet on the right side, as well.
Thanks, we are going to seal around the radiator to prevent the recirculation of the heated air. It's in the works
Rear lights look odd with there being 3 instead of 2. No 'Vair came with 3 LOL
Awesome!
@@johnsayles4316 thank you
por favor cuando ud adacto el motos v6 en el corvair , lo acoplo al tren de traccion original del corvair, quiero decir acoplo el motor v6 a la transmicion y a la caja original del corvair
We are using the original transmission and rear axle from the Corvair. We used an adaptor belhousing to do this
Love it.
i would try it with hood off and see what ir needs exactly
Awesome Man!
Thanks. Just about close to done
Stay cool 😎
Thanks BUCK, tryin' to!
GM vortec 4.3 ???
Thanks for watching. I think this 4.3 would not be considered a vortec. It's from an 85 pickup
Anyone can confirm this is boxer 6 cyl. 4300 cc engine?
Please.
This is NOT a boxer air cooled engine anymore. This is now a water cooled V6. Thanks for checking out the video
Why not mount radiator under spare tire in trunk,hard pipe supply/ return back to engine . Electric fan blow down w/ air duct under front bumper ,out of sight
@@WilliamLager-m1u for some reason we were trying not to alter the looks of the car. A front mount radiator would definitely have worked better
Nice … how about disc brakes ?
Thanks for watching. I'm pretty sure that disk brakes aren't necessary with the weight of the car and the balance
Car is light enough drums are plenty good
@@Raycr Agree....plus drums have more pad material and are lighter than disc setups
Keep the updates coming on this, love oddball builds!
Keep it original
It's a little late for that! We have others that are still the way GM built them
@@Raycr What $ range do you think a decent driver condition later 2 door might fetch?
Wanting one of these! Dont want a major project nor a car thats too nice. Reliable, sorted.
SoCal thanks!
@@gordocarbo Thank you. As for a price? I really don't have a good idea. Location often makes a big difference. Checking back yards will probably get you a better price than any advertised car
That's a really cool build/ project!!!👍Please check out my 1968 Barracuda fastback powered by a rowdy 512 stroker backed by an A833 4 speed manual. I think you'll approve. 👌
That Cuda looks good and sounds great!
@@Raycr Thanks a lot. It's an absolute pleasure to drive. 👍
Weight difference between the v and flat 6?
“What is the weight difference between the V6 and the Flat 6 engines?” There, I fixed it for you.
Without proper airflow from the outside it will never run cool
We're working on airflow control now, and a fan setup with more CFM and shrouding. Hopefully that will get us where we need to be
When I had a heating problem with a motorcycle I went with 100 percent antifreeze, 30 years later it hasn't overheated again, just saying
I'm going to start with air flow management, I'm sure with this configuration that there's room for improvement!
Pure antifreeze is way less efficient for cooling than antifreeze mixed with water. If you run pure antifreeze your engine will run warmer, not cooler.
@@nojunkwork5735 believe what you want, I tried in vain mixing it , it kept running hot until I went with straight antifreeze, doesn't antifreeze have a higher boiling point than water
Former radiator man here: 50/50 mix of water to antifreeze gives optimum cooling. Yes, antifreeze has a higher boiling point, but you don't want a coolant that absorbs more heat. It also loses heat slower than water. Can't say about your motorcycle, but it is not likely that it's running cooler no matter what your gauge says. For best results in any water cooled motor use distilled water. Captured rain water will do.
@@johnchandler1687 like I said I tried it like you pros said and it kept running hot so I did what I did and the light hasn't come on and the coolant hasn't come out your saying the very same thing the Suzuki people told me but it didn't work for my bike, my saying is whatever works as a matter of fact the fan hardly ever comes on, it's got to b really hot for it to Evan come on.
Plowed like a JohnDeere.
Not a problem, I'm in farm country
@@RaycrI have some questions about the Corvair the original engine in mine went out and was wondering if you would recommend the v6 swap and if you used the original transmission
@Isaac -sv7xt. It all depends on what you want out of your car. Do you want to just have a solid dayly driver? Do you want to increase proformance? You should evaluate what you want to end up with. The stock engine can be a good little power plant.