Wonderful video. I normally upon battery changes in watches always mark the inside of the case back to record the expiration of our warranty for the battery life. Certainly helps when the customer returns saying they "just" had their battery changed. Upon examination of their watch I find it was something like 3 years since their watch was here for the battery change. Recording the installation date or the expiration date sure does help.
@express375 Thanks for your comment. The first rule is to not let dirt get in the watch and the second rule is to not touch anything inside the watch with your fingers - if any of this happens then to make sure to remove the finger prints or dirt with Rodico. And of course, it is so important not to use cheap batteries which can leak in the watch.
Everything you provided in this video is correct with the explanation of the existing battery in this Omega. You may want to provide your audience admirers how to test the quartz movement for ability to run just how low the voltage can be before the movement stops completely. This, as you know, with a movement testing device. Just the statement 1.38 volts was too low is overlooking what the movement's circuit is performing on battery drain. I have had cleaned movement's go down as low as 1.00 volts before completely stopping. Just a suggestion, no criticism at all. Your videos are wonderfully educational for us.
Thanks for taking the time to make the vid.I know it takes ten times as long to do a job when you are making a video of the process.I used to change watch batteries when I had a shop,and although I did a much better job than the shoe repairer down the road(used to get the ones he could get the back back on),this is far superior than I ever did.
In the US: Otto Frei - In the UK: Cousins - In Germany: Beco Technic - Or you can get them on eBay. The one I use is Calypso but is works in the same principle as the Bergeon version.
could you make one with a watch case you know will leak, because when I do it to show its safe for a watch I always end up having a droplet of water inside so I guess it still goes in no matter the pressurization
I have the same omega but it has a problem. Whenever it reaches a certain time like 10:53 it stops operating or it gets stuck. Can you tell me anything i could do?
Mark thank you so much for a detailed video, I was able to replace my watch battery no problem. I'm wondering what size screwdriver you used to loosen the screw to release the crown? I don't seem to have the right one in the kit I bought.
@TOPHER142 - Not a good idea to de-magnetise any electronic watch at all. Hold it to your ear - if you hear a whine then the electronics are OK but there will be a block in the wheels. If there is no sound (whine) then check that the battery is in the correct way: On Accutrons the POSITIVE (+) is down and the NEGATIVE (-) is up. There should be no short between the positive and negative either. It sounds like your automatic watch needs to be serviced - service interval should be 3 - 5 years :)
I watched this to see if there was a particular step taken to reduce the humidity level of the air when closing the watch. I didn't see such a step. Just curious if that's a concern. Otherwise I would think you might get condensation when you're out in real cold weather. To be safe, I might heat the watch first if I changed a battery at home guess. But I thought the pros might use nitrogen or something.
Hello Mark, what sort of a brand is that watch press/vice that you are using in this video if you wouldn't mind sharing? Do you still use it? Or have you changed to a new one. Thanks.
The tester pressurizes the compartment with the watch inside, and if there's a leak, the watch gets pressurized inside, and if it's subsequently dunked in the water with the pressure released, the air will start bubbling out of the watch, indicating it's leaking. Because the watch would have high pressure air inside if it's leaking, it keeps the water from getting in. The statement about it's safe as bubbles are coming OUT of the case is being compared with if water is going IN the case, if it were done by simply dunking it in water without using this method, because then it could allow water into the watch, ruining it. Plus there's no visible indication it's leaking if it's just dunked in water, you'd only know after you find it got waterlogged. The flaw in testing might be if the watch is entirely leaking, which would result in the high pressure air immediately escaping, and when dunked, allow it to to get flooded. This test has to assume the watch is at least moderately water resistant, and not open to the air. The video seems to jump past the actual part of the test where the pressure is released and the watch dunked, for some reason. It would have been interesting to see the full sequence there.
Yes, it should NOT show any bubbles; he was just saying that if it did leak, it's safe because it results in the air moving out of the watch, and not water going into the watch.
You have to pay more atention to the videos. Before he inserts it in water he pressurizes it. So watch has air pressure inside in case of leak, and when gets in the water part of it bubble, of course pressure inside the watch avoid water getting in.
After you have plunged the watch in, and start slowly releasing pressure - am I correct in thinking you need to either stop releasing pressure or remove the watch before you have completely released all pressure to ensure water is not able to enter any possible passages (if you discover the watch has leaks)?
Renata battery will also leak if leave in the watch too long. I find Maxell made in Japan is the best of the best from my 40+ years of experience in this business.
+EastLakeWatch yes, renata leaks 90% of the time if left to long in the watch, i would say it is the worst battery of all, maxell, seizakein(made by seiko) sony, or energizer is much better choice...and the battery popt out from the movement on the vid when you instaled it...:) btw, love your tutorials...
Mark, have you ever dismantled your calypso tester? I've purchased one that needs a service, I know where to get the new parts, but what I don't know, is how to dismantle the manual pump?
Nice! Thanks Mark I resonantly come across 2 Bulova's, one is a 1967 Accutron and replaced the batt and Nothing? It had been sitting in a box for many years. I think may need to be demagnetized..? The other I have is a automatic 30 Jewel Self Winding also from the 60s and in hibernation for some time, tried winding it but no go. Ive been having trouble getting the back off..? Probable a good thing at this point considering I don't know what the hell I'm doing.. ;) Thanks!
Thanks for the video... I just paid a jeweler to replace my watch battery, because I need it to stay waterproof, however it no longer is. Don't know weather I should take it back to him, or if it's my fault I didn't ask enough questions? I appreciate the detail that goes into doing this correctly and am willing to pay.
I have the very same watch and the cost of sending it for a service is insanely high. Would you still recommend having the watch professionally serviced periodically or is it safe to assume that unless there is a specific fault then a DIY service is a legitimate option for me? My Seamaster has a problem and has been sent away but no work carried out yet. Moisture had got inside and corroded the battery contacts from what I understand. The battery had developed rust as a result. My quote for the repair, which I hope includes a new battery is £250. Does this sound like something that can be repaired at home?
Great video. My question is, you can clearly see some form of black powder around the gasket when first taken off. This stuff fell into the inside of the watch. If this was a mechanical watch this would be really bad. Regardless, the black powdery dirt should had been cleaned before proceeding. Also, if the black powder was present on the gasket perhaps a new gasket should had been used just in case.
I see later on he cleaned some of the debris but by then it would be too late. A few more comments: 1. I would NOTjust flip the watch over to remove the magnetic shield. In the video you can see all kinds of stuff fell over (battery, battery shield), I would also keep the entire watch inside a holder. 2. The battery compartment is such that the battery fits snug inside. In the video it is shown as being placed loosely inside! It is supposed to fit in a locked position by two side connectors. 3. I would leave the crown untouched. There should be no need to lube the crown on every battery replacement. 4. What is the torque used to close the back cover? 5. The PSI pressure in the calipso pressure tester should had been set to 435 PSI (300 meters i.e. 1 meter sea water [msw] = 1.4503773773 psi [psi])
@@pitsiriki933 what about using gloves to do this? Some of the body natural lubricants can be present while he is touching everything with bare fingers
@@pitsiriki933 that pressure tester only goes to 10 bar, and you have to take the stem out to service the orings if you're planning to have a waterproof watch. If you want to certify a dive watch back to its advertised depth rating you'll need a much more expensive pressure testing chamber.
Great video. Professional and informative in every way. Thank you! BTW, are there any special issues or concerns to be aware of when changing batteries in RipCurl ATS Ocean Search Tide watches?
question... if the watch failed the waterproof test, wouldn't the watch be ruined? Seems you would not want water to leak into the watch as it would ruin it.
dsonyay for what I understand he first expose the watch to pressurized air wile been in the chamber. so if there is any leak air will go inside the watch.. he then puts it in the water to see if there any air bubbles coming out. if air comes out it means water can come in.. this is just what I understood I hope it helped you!
I've Watched Tons of Your Videos and love your Complete Coverage Of Your Wonderful Workmanship....I Have A Seiko Diver Pepsi Skx With With A Bad Balance (I Tried To Get A Little Faster Movement By Pushing to The Positive And Slipped Damaging The Hairspring) Foolish Of Me I Know...( And I Cant Find Anyone In My Area Who Would Fix it For Me....Always Excuses Like Hard to Find Parts To Not Interested For What Ever Reason So It Sits....I Wish You Was Around Meadville PA Area...So that It Could Be Fixed Properly... Once and for all.....Help Tell Me Who Best To Send It out To..please..I'm Clueless!!!!
You Tube good noon with the best wishes You are performing y our's best duties you are every where in th is World with the best programme God glad e all of you.Thanks.
Bergeon 'Rodico' - It's almost like a putty/blu-tac. It's used for ALL kinds of watch related things, like holding pieces, picking up tiny hands or screws, cleaning grease and oils etc.. it's only cheap too.
Is duracel a good brand of batterie s because other wise i need to pay a watchmaker 25 €!!! For "swiss" quality batteries and he doesn't even reseal the watch for that price. so my dad/amateur watchmaker just reseals them for free : new gaskets and if needed he even services watches for an extra 10€ (free for me though) he is very onest when it comes to his watch hobby and offering repairs for friends only since he is not a Professional
just to say renata batterys are leaking more then maxell, seizeken, sony or energizer...i would say renata is the worst battery among those for replacing in watches, and also most expensive...on and the battery didnt sit well in the movement...;)
so to do a battery change on a waterproof/dive watch, you either need this equipment or you get it done professionally.. makes all those "let's mod a watch cheaply and easily", pretty much null and void.. amazing the amount of crap on TH-cam..
Wonderful video. I normally upon battery changes in watches always mark the inside of the case back to record the expiration of our warranty for the battery life. Certainly helps when the customer returns saying they "just" had their battery changed. Upon examination of their watch I find it was something like 3 years since their watch was here for the battery change. Recording the installation date or the expiration date sure does help.
@express375 Thanks for your comment. The first rule is to not let dirt get in the watch and the second rule is to not touch anything inside the watch with your fingers - if any of this happens then to make sure to remove the finger prints or dirt with Rodico. And of course, it is so important not to use cheap batteries which can leak in the watch.
It's clear and informative videos like this one that makes youtube actually useful! Thank you very much for posting!
Its...."Thanks" for watching....Not "Fanks" for watching.
Just perfect!...This is the best instructional video I've seen yet on battery replacement.
Everything you provided in this video is correct with the explanation of the existing battery in this Omega. You may want to provide your audience admirers how to test the quartz movement for ability to run just how low the voltage can be before the movement stops completely. This, as you know, with a movement testing device. Just the statement 1.38 volts was too low is overlooking what the movement's circuit is performing on battery drain. I have had cleaned movement's go down as low as 1.00 volts before completely stopping. Just a suggestion, no criticism at all. Your videos are wonderfully educational for us.
my respect to you sir! Your dedication when seeing you work it's inspiring
Thanks for taking the time to make the vid.I know it takes ten times as long to do a job when you are making a video of the process.I used to change watch batteries when I had a shop,and although I did a much better job than the shoe repairer down the road(used to get the ones he could get the back back on),this is far superior than I ever did.
In the US: Otto Frei - In the UK: Cousins - In Germany: Beco Technic - Or you can get them on eBay. The one I use is Calypso but is works in the same principle as the Bergeon version.
could you make one with a watch case you know will leak, because when I do it to show its safe for a watch I always end up having a droplet of water inside so I guess it still goes in no matter the pressurization
I have the same omega but it has a problem. Whenever it reaches a certain time like 10:53 it stops operating or it gets stuck. Can you tell me anything i could do?
Mark thank you so much for a detailed video, I was able to replace my watch battery no problem. I'm wondering what size screwdriver you used to loosen the screw to release the crown? I don't seem to have the right one in the kit I bought.
@TOPHER142 - Not a good idea to de-magnetise any electronic watch at all. Hold it to your ear - if you hear a whine then the electronics are OK but there will be a block in the wheels. If there is no sound (whine) then check that the battery is in the correct way: On Accutrons the POSITIVE (+) is down and the NEGATIVE (-) is up. There should be no short between the positive and negative either. It sounds like your automatic watch needs to be serviced - service interval should be 3 - 5 years :)
Just splashed out and bought one of these Calipso testers. All good - thanks for the fine video Mark.
I watched this to see if there was a particular step taken to reduce the humidity level of the air when closing the watch. I didn't see such a step. Just curious if that's a concern. Otherwise I would think you might get condensation when you're out in real cold weather. To be safe, I might heat the watch first if I changed a battery at home guess. But I thought the pros might use nitrogen or something.
Hello Mark, what sort of a brand is that watch press/vice that you are using in this video if you wouldn't mind sharing? Do you still use it? Or have you changed to a new one. Thanks.
Excellent Presentation, So How do I send my two watches to you ?? Thank You
7:56 did he say "as bubbles ARE coming out of the case, it is safe"?
The tester pressurizes the compartment with the watch inside, and if there's a leak, the watch gets pressurized inside, and if it's subsequently dunked in the water with the pressure released, the air will start bubbling out of the watch, indicating it's leaking.
Because the watch would have high pressure air inside if it's leaking, it keeps the water from getting in.
The statement about it's safe as bubbles are coming OUT of the case is being compared with if water is going IN the case, if it were done by simply dunking it in water without using this method, because then it could allow water into the watch, ruining it. Plus there's no visible indication it's leaking if it's just dunked in water, you'd only know after you find it got waterlogged.
The flaw in testing might be if the watch is entirely leaking, which would result in the high pressure air immediately escaping, and when dunked, allow it to to get flooded.
This test has to assume the watch is at least moderately water resistant, and not open to the air.
The video seems to jump past the actual part of the test where the pressure is released and the watch dunked, for some reason. It would have been interesting to see the full sequence there.
*****
I expected bubbles coming out to indicate a leak? I expect a properly sealed watch to not allow water or air in, even under pressure.
Yes, it should NOT show any bubbles; he was just saying that if it did leak, it's safe because it results in the air moving out of the watch, and not water going into the watch.
+ H WMD thanks for taking the time to explain this i too was a bit confused as to how this worked! nicely explained, thanks again.
You have to pay more atention to the videos.
Before he inserts it in water he pressurizes it.
So watch has air pressure inside in case of leak, and when gets in the water part of it bubble, of course pressure inside the watch avoid water getting in.
loved your video sir. how much would it cost to do this for a G shock G-3011? would love you to do this sir .
Excellent video. Thank you. I had to work my way through many less informative videos before finding this one. I need search no further.
Learning a lot from you and Robert perrett
Tested with movement installed !! Very brave man Mark !. I know you are the expert and have full confidence in your work. Well Done Sir.
After you have plunged the watch in, and start slowly releasing pressure - am I correct in thinking you need to either stop releasing pressure or remove the watch before you have completely released all pressure to ensure water is not able to enter any possible passages (if you discover the watch has leaks)?
Hi! Is it necessary to remove the crown and stem before replace the battery in every watch? tahnks
Renata battery will also leak if leave in the watch too long. I find Maxell made in Japan is the best of the best from my 40+ years of experience in this business.
+EastLakeWatch
yes, renata leaks 90% of the time if left to long in the watch, i would say it is the worst battery of all, maxell, seizakein(made by seiko) sony, or energizer is much better choice...and the battery popt out from the movement on the vid when you instaled it...:)
btw, love your tutorials...
I use Sony and Renata. It will be Sony and Maxell from now on for sure. . Thank you very much for your long time experience.
Toshiba is much better than maxell
No disrespect but if Renata batteries are the best then why do Maxwell batteries cost more.
Personally I've being using maxell batteries for 26 years
I work for the biggest watch repair watch company we use Sony batteries I've been doing watches for 20 years and always used Sony
Great video . I was able to do my watch at home . It is waterproof again. Tested it and it's good upto a few meters at least 😅
Mark, have you ever dismantled your calypso tester? I've purchased one that needs a service, I know where to get the new parts, but what I don't know, is how to dismantle the manual pump?
At 4:39 what is that rubber thing you used called. Rubico?
Rodico
I have the black version of this Omega great watch, and just so happens I need the battery replaced
Does your Calypso tester have any problems holding steady pressure? Just bought one, and it won't hold constant pressure.
Aloha from Maui
Nice! Thanks Mark
I resonantly come across 2 Bulova's, one is a 1967 Accutron and replaced the batt and Nothing? It had been sitting in a box for many years. I think may need to be demagnetized..?
The other I have is a automatic 30 Jewel Self Winding also from the 60s and in hibernation for some time, tried winding it but no go. Ive been having trouble getting the back off..? Probable a good thing at this point considering I don't know what the hell I'm doing.. ;)
Thanks!
I love your channel! What is that cleaning putty that you use?
hi , does the Calypso hold pressure ?
Hi, can i spray silicone on the rubber cap before I close?
I lost the battery "Isolator"! ugh! where you can you find replacements?? great videos.. thanks
Thanks for the video... I just paid a jeweler to replace my watch battery, because I need it to stay waterproof, however it no longer is. Don't know weather I should take it back to him, or if it's my fault I didn't ask enough questions? I appreciate the detail that goes into doing this correctly and am willing to pay.
Gallivanting Val go to someone else
Can these practices of opening and closing the watch be applied to regulation of a mechanical water resistant watch as well?
Hi, do you recommend the Calypso tester or should I go for the Bergeon? Thank you for good videos.
There a complete ecosystem inside the waterproof testing machine!
Hi where are you located, and will you repair watches if they were sent to you by mail for repair..?
What type of cleaning brush do you recommend?
I have the very same watch and the cost of sending it for a service is insanely high. Would you still recommend having the watch professionally serviced periodically or is it safe to assume that unless there is a specific fault then a DIY service is a legitimate option for me? My Seamaster has a problem and has been sent away but no work carried out yet. Moisture had got inside and corroded the battery contacts from what I understand. The battery had developed rust as a result. My quote for the repair, which I hope includes a new battery is £250. Does this sound like something that can be repaired at home?
Thank you for producing quality contents!
where can i get the waterproof machine
Great site, Mark. Thank you.
Has the crystal ever blown off?
Great video. My question is, you can clearly see some form of black powder around the gasket when first taken off. This stuff fell into the inside of the watch. If this was a mechanical watch this would be really bad. Regardless, the black powdery dirt should had been cleaned before proceeding. Also, if the black powder was present on the gasket perhaps a new gasket should had been used just in case.
I see later on he cleaned some of the debris but by then it would be too late.
A few more comments:
1. I would NOTjust flip the watch over to remove the magnetic shield. In the video you can see all kinds of stuff fell over (battery, battery shield), I would also keep the entire watch inside a holder.
2. The battery compartment is such that the battery fits snug inside. In the video it is shown as being placed loosely inside! It is supposed to fit in a locked position by two side connectors.
3. I would leave the crown untouched. There should be no need to lube the crown on every battery replacement.
4. What is the torque used to close the back cover?
5. The PSI pressure in the calipso pressure tester should had been set to 435 PSI (300 meters i.e. 1 meter sea water [msw] = 1.4503773773 psi [psi])
@@pitsiriki933 what about using gloves to do this? Some of the body natural lubricants can be present while he is touching everything with bare fingers
@@pitsiriki933 that pressure tester only goes to 10 bar, and you have to take the stem out to service the orings if you're planning to have a waterproof watch.
If you want to certify a dive watch back to its advertised depth rating you'll need a much more expensive pressure testing chamber.
Great video. Professional and informative in every way. Thank you!
BTW, are there any special issues or concerns to be aware of when changing batteries in RipCurl ATS Ocean Search Tide watches?
Nice video and very informative. Thank you.
hello I'm a watch smith as well y did u say tag and omega use renta battries when they knw use Sony ones
Sir Please upload video How to set the time in Casio wave captor World time watch
Excellent work sir thank you 👍🏼👍🏼👍🏼👍🏼👍🏼
Thanks for posting the video. Very informative.
Do you get headaches from working on watches ?
I'm sorry for the dumb question, but I'm curious. If the watch does fails the water pressure test and takes on water what do you do?
Go back and replace the rubber gasket....start over.
Why would a quartz watch need an iron shield? Aren't they significantly more resistant to magnetization than mechanical movements?
ION shield not iron. It deflects electric interference. That's why James Bond always wears Omega watches :)
@@dgoettel13 But everyone knows q branch had to remove the ion shield to fit the 10kw laser and explosive for those everyday emergencies
Quero parabenizar a todos os artistas esquecidos por estes conteúdos tão expressivos da nossa profissão
good viddeo. where can i geta new gasket for my tag heuer formula 1 watch mid-sized mans watch.
Damn, I wish you were my watch repair guy.... nice job, great video :) thanks :)
Extremely helpful, Thank you!!!
Thanks for posting the video.
You are welcome.
Cool Thanks Mark.. Looking forward to more videos.
TOPHER142 Cu penseta ai luat de doua ori bateria,si de doua ori ai pus bateria electrica in scurtcircuit!!!💀
HOW DO I OPEN THE BACK ????
In a new town so know what to ask, thanks great video;s
question... if the watch failed the waterproof test, wouldn't the watch be ruined? Seems you would not want water to leak into the watch as it would ruin it.
dsonyay for what I understand he first expose the watch to pressurized air wile been in the chamber. so if there is any leak air will go inside the watch.. he then puts it in the water to see if there any air bubbles coming out. if air comes out it means water can come in.. this is just what I understood I hope it helped you!
Ali Mubarak makes sense. i must have missed that part. thanks :)
fantastic video thank you
What happen if in that watch water get in?
I've Watched Tons of Your Videos and love your Complete Coverage Of Your Wonderful Workmanship....I Have A Seiko Diver Pepsi Skx With With A Bad Balance (I Tried To Get A Little Faster Movement By Pushing to The Positive And Slipped Damaging The Hairspring) Foolish Of Me I Know...( And I Cant Find Anyone In My Area Who Would Fix it For Me....Always Excuses Like Hard to Find Parts To Not Interested For What Ever Reason So It Sits....I Wish You Was Around Meadville PA Area...So that It Could Be Fixed Properly... Once and for all.....Help Tell Me Who Best To Send It out To..please..I'm Clueless!!!!
do not you do a dry waterproof test?
sehr schönes Video , so eine seamaster hab ich auch , ist mir nützlich das Video , danke
why dont water testing without a moment in the watch?
very informative !
Excellent!
What would happen if you left finger prints inside the watch
Fingerprints will corrode or stain any metal parts in the watch.
The last time I went to a shop to get a new battery in my Seamaster, they wanted over $500 for 10 minutes work.
$500 for a battery and pressure test?! That’s nuts
You touched the battery with your left index finger instead wearing finger or latex gloves😎
The best!!!
You Tube good noon with the best wishes
You are performing y
our's best duties you
are every where in th
is World with the best
programme God glad
e all of you.Thanks.
Good video
unfamiliar terminology: "radico" (bluish cleaning material)?
Bergeon 'Rodico' - It's almost like a putty/blu-tac. It's used for ALL kinds of watch related things, like holding pieces, picking up tiny hands or screws, cleaning grease and oils etc.. it's only cheap too.
Why did u not use a dry pressure test machine so much easier and tag and omega now use Sony batteries
Interesting, thank you.
So that tiny piece of rubber gasket is what keeps it 100M+ of water resistance?!
Sure is! Plus the crystal which most have a gasket
Is duracel a good brand of batterie s because other wise i need to pay a watchmaker 25 €!!! For "swiss" quality batteries and he doesn't even reseal the watch for that price.
so my dad/amateur watchmaker just reseals them for free : new gaskets and if needed he even services watches for an extra 10€ (free for me though) he is very onest when it comes to his watch hobby and offering repairs for friends only since he is not a Professional
AV Cuber If I need to get a watch resealed it will cost me $200! From the only watch shop in my area.
That’s what I need to find in Indonesia.
So "best practice" is to clean the main gasket and not the crown gasket ? Are they is good shape ? It looks not...
Exelliant
If that were a aircraft component we would have replaced all those O rings.
just to say renata batterys are leaking more then maxell, seizeken, sony or energizer...i would say renata is the worst battery among those for replacing in watches, and also most expensive...on and the battery didnt sit well in the movement...;)
I thought Omegas were mechanical watches??
There are many quartz ones too, they're very well-made and reliable, just like their automatic counterparts
mai bhi kam kar sak ta hu koi badi bat na hi h
Nice video but please stop breathing into the mic
mah nat ki koi valu na hi h du sarai mai kai nik ki valu hi
watch ka kam ki koi valu na hi ha ji
Sorry I disagree that Renata batteries are the best 30 years I've been using Maxwell batteries always outlast Renata plus Maxwell cost more
Could the quart movt in to mechc.movt?
so to do a battery change on a waterproof/dive watch, you either need this equipment or you get it done professionally.. makes all those "let's mod a watch cheaply and easily", pretty much null and void.. amazing the amount of crap on TH-cam..