Superb! You do such a great job explaining things. Though my Escape is a 2006, it is also manual transmission. Thanks for sharing additional information about clutch safety that I have not seen elsewhere.
Following your path, I found my issue was that the clutch pedal switch fell off of its mount. Now I have a spare starter. Big thanks for your help solving my problem.
THANK YOU!! I replaced the Damm starter before I saw this video 😢 Now all bruised and feeling let down because the truck still won't turn over... I checked all fuses. They were fine. Swapped the relay with its neighbor, like you said and IT STARTED!! YAY🎉😂 Again! Thank you!!
My man! Very good video. Truly very informative and clear. Much appreciated. I'm trying to help my friend get his 2006 started. Good battery, but just does nothing when you try to start. This will help me follow the whole system and check each component. Liked and subscribed! Pro tip - other people trying to make similar videos need to learn from this guy.
Just fixed my no start no crank battery works by replacing the 2amp fuse - pcm. Holy cow that feels good. It's fuse #5. All other fuses were fine. Dang 🎉
Thank you. I do have a question, which fuse is for the car alarm on a 2005 Ford Escape Limited?? And can a Car parts store test it?? My car alarm keeps going off and I suspect a bad fuse, at the very least I want to check it. My car battery is only a couple of months old. I thought that might be the problem since it was near it's lifes end, and it did seem to help for a little while but then it started going off again.
Hello, on the side of the fusebox I see two wires with a boldt. What are they? Looking at them, I see a lot of corrosion in the wire. Let me explain this to you. I parked the car at 4 pm and went into the house. The next day I went to start the car, I put the key into the Ignition and as usual, all the lights on the dash came on. But when I continued to try to start it, I heard no sound. Nothing clicking from the starter. Or anything. I got out, raised the hood, and put jumper cables on the battery from another car. Got in the escape, turned the key, and still the lights came on, But nothing happened. I heard no sound, no clicking or anything. Out of frustration, I let the hood slam back to the locked and closed position. I got into the car to get the keys, and something said try to start at 1 last time. I turned the key and the car started. What do you think the problem could have been? Thanks for reading my note. Love your wire diagram
If I've lost the ignition key and have a key without the one chip that unlocks the door and will turn the ignition switch will the car start by turning the key on and manually engaging the starter
Good to hear your understanding of the fuses and diodes. I have a strange issue with the BCM. Everything functions, power windows, lighting, door locks with my key in the 3rd position (run?), but when I start the Escape which runs great, I lose power for the windows and door locks. Aftermarket radio works, headlights, cruise, etc all work. Just no power locks or power windows after the car is running. Thinking a ground because in 3rd position isn't my starter energized ? Then not just after crank? Thanks for any hints. It's automatic, 3.0.
@@LehewTech 1FMCU04143KE14780 GDEX2R@GMAIL.COM This car recently carried me, 2 adults, 2 dogs, a loaded trailer across the country. No problems except locks and windows. Next step was to tear into the BCM but perplexed when I discovered I could control both just before starting car. Can even stop car, again turn key to accessory (3rd position) to roll any window up. Unbelievable you responded so quickly. Impressed and thankful, glenn
HI I'm having an interesting I cannot get the escape to I don't have a wiring diagram can you send e one 2005 ford escape my email is karl.borgen@live.com one thing I notice is that there is a white ling on the transmission shift indiacator and when they match the cars is in drive? I though that this would be in neutral and not drive could this be the problem I do not get power to the start relay? Thank You
I am looking at 2005 Escape the battery light on the dash. I replaced the original one a month ago and last night it came on again last night. Car running engine on idle with multi-meter less than 12v clean battery terminals, try again still only 11.77V. Replaced original removing passenger front axle etc. reassembled and light went out good to drive. Three weeks later same light comes on and voltage has dropped again?? Have to pull it apart again to have the rebuilt bench tested. But just wanted to see if there is something I’m missing! Thanks in advance any help would be great I know the parts store found my old one on the core shelf. Luckily it was still there but I will end up paying the mechanic to remove the rebuilt, and charge me again to reinstall it. He is quite good at the R&R but still 4hrs. I have to pay for but would really like not pulling the 1 month old rebuilt out if I don’t have to.
Aye bro so my husband's Ford explorer 2005 isn't starting. It worked COMPLETELY fine before my dad switched some fuses around and now it wont start. What can we do to fix it
I hope you might be able to help me my 2005 mercy mariner was running fine I had to get the fuel out of the tank so I watched a video on how to bridge the starter relay so I was trying to bridge it over I was on the wrong relay I guess it got a ground it was the relay first one past the fuel pump relay toward the starter relay now it won't crank over and the fuel pump has no power please if you could help me your video did help me so much I have check all fuses they have power on both sides thank you.
IN my daughters 2006 escape, auto trans, 3.0 V6, the 25 amp fuse is missing. The fuse that you pointed out that sends power to the inside fuse box.. should there be a fuse in that position and if it isn't there could that be why the balking starter. FYI, pushing in on the inition key in the run position, then while holding in turn to the start position seems to help balky start. new battery, alternator charging 14.2.
What if it will not start, dash lights come on, starter does not even engage or click or do anything, then sometimes 2 min later, it starts right up normal? Where should I look for issues first?
Awesome, thank you. My car rolls over a couple cranks only. Sounds like dead battery but new, charged and charger on it. When I pull out my key, the gauges fissed and went nuts for a couple seconds. So will check this all out, terrific job.
I have a 2005 automatic escape. All fuses are good, switched diode, changed out relay, brand new battery. Still no crank. I bi-passed relay and starter does turn but engine still wont start. Tried it in both park and neutral. any ideas?
hello i have problem i have remove all relay and next starter not working also fuel pump can u help me for relay ampers? what amper where want to install?
Thanks for this my friends escape had a dead battery I checked it and had a draw on fuse 11 which was ignition fuse could it be a bad relay drawing 2.6 amps
Having a no start no crank issue. Been chasing it for months. Only thing it will do is click at the inside fuse panel. I have checked all fuses. Checked starter. Everything. Only started this after I replaced the battery
My escape engine turns over it just dont run on D drive. Or R... A/C blows all sounds good. It just shows a 🔐 w 🚗 red light..? Any idea whats going on???
Hello, ford escape 2006... when i switch on to start , the car doesn't start, doesn't make any sound, battery is good...after several tries it starts, it happens each time that i try to start the car.
I have a 2006 ford scape 4cilynders 2.3 automatic the problem is that when I drive it like 10 miles and it reaches the normal temperature of the car after I try to turn it back on it won't start but when is cold always start it doesn't get over heat just reaching the normal temperature of the car what could be the problem
Superb! You do such a great job explaining things. Though my Escape is a 2006, it is also manual transmission. Thanks for sharing additional information about clutch safety that I have not seen elsewhere.
Following your path, I found my issue was that the clutch pedal switch fell off of its mount. Now I have a spare starter. Big thanks for your help solving my problem.
THANK YOU!! I replaced the Damm starter before I saw this video 😢
Now all bruised and feeling let down because the truck still won't turn over... I checked all fuses. They were fine. Swapped the relay with its neighbor, like you said and IT STARTED!! YAY🎉😂 Again! Thank you!!
My man! Very good video. Truly very informative and clear. Much appreciated. I'm trying to help my friend get his 2006 started. Good battery, but just does nothing when you try to start. This will help me follow the whole system and check each component. Liked and subscribed!
Pro tip - other people trying to make similar videos need to learn from this guy.
AWESOME THANK YOU FOR THE TIPS ON FUSE RELAYS AND TROUBLESHOOTING !! great tutorial !!
Good luck!
This is an excellent video! Thank you for sharing the information!
Wow! Great video man! Well spoken and competent. Good job.
Thank you sir!
Thank you you probably saved me from losing my mind. I thought I may have popped the ECM. What a great help this video was. You rock!!
Really helped! Thanks, you're a pro!
Thank you brilliant info
Just fixed my no start no crank battery works by replacing the 2amp fuse - pcm. Holy cow that feels good. It's fuse #5. All other fuses were fine. Dang 🎉
Good looks brother very helpful 👍🏾
Sounds great this should help, I'm helping a friend on theres so I'd do some research first. These things have sure changed from the old ones
Thank you. I do have a question, which fuse is for the car alarm on a 2005 Ford Escape Limited?? And can a Car parts store test it?? My car alarm keeps going off and I suspect a bad fuse, at the very least I want to check it. My car battery is only a couple of months old. I thought that might be the problem since it was near it's lifes end, and it did seem to help for a little while but then it started going off again.
Hello, on the side of the fusebox I see two wires with a boldt. What are they? Looking at them, I see a lot of corrosion in the wire. Let me explain this to you. I parked the car at 4 pm and went into the house. The next day I went to start the car, I put the key into the Ignition and as usual, all the lights on the dash came on. But when I continued to try to start it, I heard no sound. Nothing clicking from the starter. Or anything. I got out, raised the hood, and put jumper cables on the battery from another car. Got in the escape, turned the key, and still the lights came on, But nothing happened. I heard no sound, no clicking or anything. Out of frustration, I let the hood slam back to the locked and closed position. I got into the car to get the keys, and something said try to start at 1 last time. I turned the key and the car started. What do you think the problem could have been? Thanks for reading my note. Love your wire diagram
Thanks from Heart
What’s the problem when I have jump the starter diode , what causes that to not start the car, , I hear the starter fuse click and even swaped it out
What was the fix brother? Same issue Im having , what fixed it for you?? Cheers
If I've lost the ignition key and have a key without the one chip that unlocks the door and will turn the ignition switch will the car start by turning the key on and manually engaging the starter
Good to hear your understanding of the fuses and diodes. I have a strange issue with the BCM. Everything functions, power windows, lighting, door locks with my key in the 3rd position (run?), but when I start the Escape which runs great, I lose power for the windows and door locks. Aftermarket radio works, headlights, cruise, etc all work. Just no power locks or power windows after the car is running. Thinking a ground because in 3rd position isn't my starter energized ? Then not just after crank? Thanks for any hints. It's automatic, 3.0.
If you drop your VIN and email I can send you the wiring diagram for those circuits
@@LehewTech
1FMCU04143KE14780
GDEX2R@GMAIL.COM
This car recently carried me, 2 adults, 2 dogs, a loaded trailer across the country. No problems except locks and windows.
Next step was to tear into the BCM but perplexed when I discovered I could control both just before starting car. Can even stop car, again turn key to accessory (3rd position) to roll any window up.
Unbelievable you responded so quickly. Impressed and thankful,
glenn
hey just sent you an email.
HI I'm having an interesting I cannot get the escape to I don't have a wiring diagram can you send e one 2005 ford escape my email is karl.borgen@live.com one thing I notice is that there is a white ling on the transmission shift indiacator and when they match the cars is in drive? I though that this would be in neutral and not drive could this be the problem I do not get power to the start relay? Thank You
Thank you sooooo much for this video. It was a gigantic help!!!
I am looking at 2005 Escape the battery light on the dash. I replaced the original one a month ago and last night it came on again last night. Car running engine on idle with multi-meter less than 12v clean battery terminals, try again still only 11.77V.
Replaced original removing passenger front axle etc. reassembled and light went out good to drive.
Three weeks later same light comes on and voltage has dropped again?? Have to pull it apart again to have the rebuilt bench tested. But just wanted to see if there is something I’m missing! Thanks in advance any help would be great I know the parts store found my old one on the core shelf. Luckily it was still there but I will end up paying the mechanic to remove the rebuilt, and charge me again to reinstall it. He is quite good at the R&R but still 4hrs. I have to pay for but would really like not pulling the 1 month old rebuilt out if I don’t have to.
Thanks a million it was really helpful.
Aye bro so my husband's Ford explorer 2005 isn't starting. It worked COMPLETELY fine before my dad switched some fuses around and now it wont start. What can we do to fix it
I hope you might be able to help me my 2005 mercy mariner was running fine I had to get the fuel out of the tank so I watched a video on how to bridge the starter relay so I was trying to bridge it over I was on the wrong relay I guess it got a ground it was the relay first one past the fuel pump relay toward the starter relay now it won't crank over and the fuel pump has no power please if you could help me your video did help me so much I have check all fuses they have power on both sides thank you.
IN my daughters 2006 escape, auto trans, 3.0 V6, the 25 amp fuse is missing. The fuse that you pointed out that sends power to the inside fuse box.. should there be a fuse in that position and if it isn't there could that be why the balking starter. FYI, pushing in on the inition key in the run position, then while holding in turn to the start position seems to help balky start. new battery, alternator charging 14.2.
What if it will not start, dash lights come on, starter does not even engage or click or do anything, then sometimes 2 min later, it starts right up normal? Where should I look for issues first?
Awesome, thank you. My car rolls over a couple cranks only. Sounds like dead battery but new, charged and charger on it. When I pull out my key, the gauges fissed and went nuts for a couple seconds. So will check this all out, terrific job.
Shiut out my friend
Have a 2005 mercury mariner same as Ford Escape it cranks but won’t start it sound like it wants to start but won’t could it be that diode?
Thanks! Engine is blown, wont roll over by hand,bumping starte to get at flywheel bolts.
Hey buddy...my 2006 escape won't start mostly in the morning unless I move around the relays which is the starter relay then it starts..why?
Thank you! Jesus bless!
I have a 2005 automatic escape. All fuses are good, switched diode, changed out relay, brand new battery. Still no crank. I bi-passed relay and starter does turn but engine still wont start. Tried it in both park and neutral. any ideas?
I also put in a new ignition switch with no luck.
I dont even have that car lol but that was a great video
Is the fuses set up the same way in the '04 as it is in the '05?
hello i have problem i have remove all relay and next starter not working also fuel pump can u help me for relay ampers? what amper where want to install?
Are these locations the same for a 2006 4cylinder?
what about the transmission system. Engine on a 4 cyl ford escape 2006 is running smooth. but does not shift until revs up real high.
Thanks for this my friends escape had a dead battery I checked it and had a draw on fuse 11 which was ignition fuse could it be a bad relay drawing 2.6 amps
Having a no start no crank issue. Been chasing it for months. Only thing it will do is click at the inside fuse panel. I have checked all fuses. Checked starter. Everything. Only started this after I replaced the battery
I would check the battery connections, make sure they are tight!
Ok
Hey man my window won’t go up on passenger side which fuse is it I don’t have manual
Hi. I need to disable my horn fuse on my 05 Escape Hybrid. Which one is it? Thanks in advance.
My escape engine turns over it just dont run on D drive. Or R... A/C blows all sounds good. It just shows a 🔐 w 🚗 red light..? Any idea whats going on???
My V6 Auto Escape is starting the motor on its own when in the run position and after it starts starter stays engaged...any ideas?
Hello, ford escape 2006... when i switch on to start , the car doesn't start, doesn't make any sound, battery is good...after several tries it starts, it happens each time that i try to start the car.
My escape 2005 will not get the Radio
Windows and headlights can you please Help?
Thank you
i have my own ford escape no power in ignition switch what is the problem
Slammed the shit out the door😂
Where does it go from the relay? I have everything aforementioned at the relay, but no signal going to the starter.
How do I test the starters signal?
And when you say start you mean run on drive (D)?
What about fuses to the transmission
I have a 2006 ford scape 4cilynders 2.3 automatic the problem is that when I drive it like 10 miles and it reaches the normal temperature of the car after I try to turn it back on it won't start but when is cold always start it doesn't get over heat just reaching the normal temperature of the car what could be the problem
Did you look into crankshaft position sensor?
No didn't check into the crankshaft position sensor
Witch one its the relay for the front wipers for Ford escape 2001v6
Relay for front wipers for Ford escape 2001 v6 i dont know wich one is
Looks a bit complicated, but after checking several times, you will get used to it.
I added a new battery but doesnt start, or turn over.
What do I do to disable the theft system on a 2006 Ford Escape
Is it locked? Cuz i think i need too.. My engine turns it just dont drive on D or R. Reverse..
Is the layout the same on the 2007 Hybrid?