Man I can’t thank you enough for the clarity of this video in the explanations of the jobs of each wire and explaining some of the wiring diagram info. Thank you brother!! I can’t wait till I get one in the shop to diagnose! 😬💪🏾
Thank you for mentioning the Wakeup signal, a lot of tech forget about this input that might only be a flash voltage, and then it's gone. Thank you for using the component ground for testing, no separate ground load test is needed, knock it out in one go. If there is an issue then do a voltage drop test on the circuit. You are saying there is no COMM from the pump back to the DME, most folks won't know the difference with and without COMM. I do not know if a water pump was changed with a wrong part number or a cheap Chinese component, is it possible that the wrong pump will have the wrong LIN Header signature similar to a wrong part number Alternator with the wrong LIN Header which will be a no COMM also?? Nice collection of DONOR parts that I notice that you have on some jobs. When a Chinese scanner shows a test, it does not mean that it can be performed, I have been told that when a Snap-On lists a test, it will happen??? You and I can see the difference in the LIN waveform but if a viewer had a simple scope, would they know the bad signal as it looks fine to to untrained eye? I wish you would have shown a close-up of the 2 different LIN Signals on the same time scale as well with some explanation, cheers.
Hello really awesome diagnostic , I have a question In negotiations to by a 2011 535i get it is havening water pump issues ..it has 4 codes 20A909 BSD WATER PUMP MISSING 20A902 reduced power cooling system voltage too low 20AB08 COOLING SYSEM NO EMERGENCY SIGNAL AT WATER PUMP ..AND 20A701 COOLANT MOTOR SPEED OUTSIDE OF TOLERANCE ..I used launch x431 to pull codes ..i i didn't do actuation test however the pump was running and operating ..all the codes say intermittent except 20ABO8..does this sound like more than the pump in your opinion
through the coolant bleed procedure, key on engine off, heat to highest temp output, fan lowest speed setting, press gas pedal down as soon as key on and hold pedal for 10 seconds then let go.... that should get the pump going and it will run for 12 minutes. Thats how you perform the bleed on the ones with electric pumps, make sure to have battery charger hooked up.
D tech I appreciate your video.. I jus bought a 2011 535i Gran Turismo with missing water pump code out of tolerance coolant pump supply voltage too low and no emergency signal .. I use a launch scanner x431.. u said something I was wondering .. does the pump suppose to run on cold start or after thermostat opens
Am I correct to say it’s because the water pump do not need to run at key on engine off that’s the reason you can’t carry out a bidirectional control using the aftermarket scan tools
That could be a possibility, but one would think that activating key on engine off would be a good way of testing for its operation, but not sure why the scanners won't work.
Can you please help... I have a BMW 2014 X3 F25 the Electric Water Pump Bleeding was working fine twice. Then, it stop after I used the Blue Devil Head Gasket Sealer. The Engine getting hot. So, I changed the Thermostat and clean out the Reservoir Tank. Same issue. Should I change the Water Pump? Is there fuse that I should check? I got 3 Codes: 1) CD9010 LIN, Message: Electric Coolant Pump: Missing. DTC Status: Current 2) 1A2004 Electric Fan, Actuating Wire: Line Disconnection DTC Status: Current 3) 1A2002 Electric Fan, Actuating Wire: Short Circuit to Ground DTC Status: Current Please help :) Thank you & God Bless
you can start by changing the water pump to see if the code for it goes away then concentrate also on fixing the fan codes as that can cause it to overheat as well
You have any experience with micsig oscilloscope? I’m needing to update my 2 channel snap on to a 4 channel but want something that’s not to hatefully expensive
I do not have experience with micsigs, but I always recommend people to get the autel 4 channel scope, it is able to be used on a pc and is VERY close and comparable to the pico. Even the software on the pc has the ability to set up markers with degree marks to take measurements, and the price is very affordable for it being pretty much like a pico.
Pretty stupid video since most people don't have actual good known water pumps to do this! In fact all you did was parts change since you had a second and third pump! This really was not a diag!!
does it make you feel better now that you got on here and ran your mouth all negatively??? I hope so, and thank you for watching and criticizing with your expertise ❤️!
Man I can’t thank you enough for the clarity of this video in the explanations of the jobs of each wire and explaining some of the wiring diagram info. Thank you brother!! I can’t wait till I get one in the shop to diagnose! 😬💪🏾
Great to hear!
Awesome. I don't work work on European cars but watching your channel i learn a lot. Thanks for sharing.
Thanks for watching!
Thank you for the information really appreciated cheers from Scotland 👍
Glad it was helpful and thank you for watching
Wow I didn't know that one Sadel. Thanks a lot. God bless.
Happy to help and thank you for watching
Thank you for mentioning the Wakeup signal, a lot of tech forget about this input that might only be a flash voltage, and then it's gone. Thank you for using the component ground for testing, no separate ground load test is needed, knock it out in one go. If there is an issue then do a voltage drop test on the circuit.
You are saying there is no COMM from the pump back to the DME, most folks won't know the difference with and without COMM. I do not know if a water pump was changed with a wrong part number or a cheap Chinese component, is it possible that the wrong pump will have the wrong LIN Header signature similar to a wrong part number Alternator with the wrong LIN Header which will be a no COMM also??
Nice collection of DONOR parts that I notice that you have on some jobs.
When a Chinese scanner shows a test, it does not mean that it can be performed, I have been told that when a Snap-On lists a test, it will happen???
You and I can see the difference in the LIN waveform but if a viewer had a simple scope, would they know the bad signal as it looks fine to to untrained eye? I wish you would have shown a close-up of the 2 different LIN Signals on the same time scale as well with some explanation, cheers.
Another excellent video, Sadel. 👍🏼
Thanks again!
Hello really awesome diagnostic , I have a question In negotiations to by a 2011 535i get it is havening water pump issues ..it has 4 codes
20A909 BSD WATER PUMP MISSING 20A902 reduced power cooling system voltage too low
20AB08 COOLING SYSEM NO EMERGENCY SIGNAL AT WATER PUMP ..AND 20A701 COOLANT MOTOR SPEED OUTSIDE OF TOLERANCE ..I used launch x431 to pull codes ..i i didn't do actuation test however the pump was running and operating ..all the codes say intermittent except 20ABO8..does this sound like more than the pump in your opinion
Isn't one the wire for dme feedback ,if pump is spinning or not.?? . Just wondering
I believe it would be through the lin communication line.
Thanks for the video , some those wster pump are controled by Lin networks ans others by Bsd or some think like that
Yes, you are right, the older ones were on bsd network that tied into other modules, this one is direct lin from dme only.
Good information, thank you. How did you trigger the wale up signal without staring the car?
through the coolant bleed procedure, key on engine off, heat to highest temp output, fan lowest speed setting, press gas pedal down as soon as key on and hold pedal for 10 seconds then let go.... that should get the pump going and it will run for 12 minutes. Thats how you perform the bleed on the ones with electric pumps, make sure to have battery charger hooked up.
Good stuff!
Have you tested if those do run with only a wakeup signal but no comms? Like a limp mode
I believe they can but obviously on this one I didn't test, but good question
So would it have woke up if u started it from cold
I would assume so
D tech I appreciate your video.. I jus bought a 2011 535i Gran Turismo with missing water pump code out of tolerance coolant pump supply voltage too low and no emergency signal .. I use a launch scanner x431.. u said something I was wondering .. does the pump suppose to run on cold start or after thermostat opens
Hey. I have the same 4 codes after installing a new pump from fcp. Did you figure out what was causing your issue. ??
@@kevinphothisen5559 hey Kevin did you receive my reply I jus text a long response
@@kevinphothisen5559 I jus tried two times to send message to you ... Not sure if you're receiving cause I don't see them after typed
@@RoadHeros610 I can see your comment here. But not a private message.
@@kevinphothisen5559 ok so you saw the original reply
Am I correct to say it’s because the water pump do not need to run at key on engine off that’s the reason you can’t carry out a bidirectional control using the aftermarket scan tools
That could be a possibility, but one would think that activating key on engine off would be a good way of testing for its operation, but not sure why the scanners won't work.
@@DTEAuto would the BMW icom software activate it
Seen you are in Fairfield ohio. Atleast if I have a foreign car issue I know where I can take it I’m In Dayton
Yeah that's not far at all, I have some that come from there
Can you please help... I have a BMW 2014 X3 F25 the Electric Water Pump Bleeding was working fine twice. Then, it stop after I used the Blue Devil Head Gasket Sealer. The Engine getting hot. So, I changed the Thermostat and clean out the Reservoir Tank. Same issue. Should I change the Water Pump? Is there fuse that I should check?
I got 3 Codes:
1) CD9010 LIN, Message: Electric Coolant Pump: Missing. DTC Status: Current
2) 1A2004 Electric Fan, Actuating Wire: Line Disconnection DTC Status: Current
3) 1A2002 Electric Fan, Actuating Wire: Short Circuit to Ground DTC Status: Current
Please help :) Thank you & God Bless
you can start by changing the water pump to see if the code for it goes away then concentrate also on fixing the fan codes as that can cause it to overheat as well
You have any experience with micsig oscilloscope? I’m needing to update my 2 channel snap on to a 4 channel but want something that’s not to hatefully expensive
I do not have experience with micsigs, but I always recommend people to get the autel 4 channel scope, it is able to be used on a pc and is VERY close and comparable to the pico. Even the software on the pc has the ability to set up markers with degree marks to take measurements, and the price is very affordable for it being pretty much like a pico.
Pretty stupid video since most people don't have actual good known water pumps to do this! In fact all you did was parts change since you had a second and third pump! This really was not a diag!!
does it make you feel better now that you got on here and ran your mouth all negatively??? I hope so, and thank you for watching and criticizing with your expertise ❤️!