![DTech Engineering](/img/default-banner.jpg)
- 219
- 1 493 604
DTech Engineering
เข้าร่วมเมื่อ 24 ส.ค. 2016
Hello, my name is Sadel. I graduated from WyoTech in 2003 and from there went on to work for BMW for about a decade. After that I spent some time in the independent shop field before deciding to open up Dtech Engineering in 2014. Along the way I noticed that I was getting a lot of trouble cars that were the hard to fix type. And so with that, I decided to start filming some of these crazy diags. My hopes with it is to help show and display diagnostic techniques and mindset thinking process along with tool usage of how to accurately diagnose automotive repairs. I hope to provide some good info along the way and hopefully teach some positive things as well. Thank you for checking out the channel and I hope you enjoy!
For any questions or inquiries, see the email address below in the detail section
For any questions or inquiries, see the email address below in the detail section
2009 Mercedes C300 No Turn Signals: Front SAM Replacement
In this video I show how to go about replacing the front SAM module on a Mercedes by cloning, and then show how to fix a no starter control issue with new SAM
มุมมอง: 870
วีดีโอ
2012 Toyota Camry Noise While Braking Diag & Fix
มุมมอง 35414 วันที่ผ่านมา
In this video I show how I found the cause of the noise while braking.
2011 BMW 535 Low Boost Code/Drivetrain Malfunction Error
มุมมอง 1.1K21 วันที่ผ่านมา
In this video I show how to diagnose the low boost condition without throwing the wrong parts at this BMW.
2013 Ram Parasitic Draw Diagnosis Part 2
มุมมอง 1.5Kหลายเดือนก่อน
In this video I show the final cause of the battery drain issue.
Dodge Ram Battery Drain Diagnosis
มุมมอง 1.3Kหลายเดือนก่อน
In this video I show my struggles of trying to figure out the intermittent battery draw
2015 BMW 750 Seat Calibration
มุมมอง 357หลายเดือนก่อน
In this video I show hot to perform the seat calibration procedure using the Lauch x431 Elite V2.0 BBA Scanner. This is a Diy based type scanner that is one of the best out there for the European market. I will handle a lot of factory scanner capabilities at an affordable price for many of European makes. Link to the tool: www.amazon.com/dp/B0CQSD48T3 Discount code: 30% Off Discount Code: HHVUGGJN
Cloning GM E69 ECM Bosch MED9.6.1 with OBDSTAR MP001
มุมมอง 717หลายเดือนก่อน
In this video I show how to clone a gm e69 engine computer with OBDSTAR DC706 and MP001.
2018 RAM Promaster P06DA Engine Oil Pressure Control Circuit Fix
มุมมอง 1.4Kหลายเดือนก่อน
In this video I show how to properly check the system for this trouble code
New Launch X431 Elite V2.0 BBA Affordable Euro Scan Tool
มุมมอง 713หลายเดือนก่อน
In this video I show some of the features of the new Launch X431 Elite V2.0 BBA. It is the best scan tool for BMW Mercedes benz VW audi DIY guys. Interested in the tool: www.amazon.com/dp/B0CQSD48T3 Discount Code: 5I5X8H46
2017 Honda Accord Push Start Button Always Blinking When Shutting Off
มุมมอง 606หลายเดือนก่อน
Just a quick video describing the cause of the 2017 Honda Accord never powering down when trying to turn off the vehicle. The light would be continuously blinking on the push start button and the center screens would stay on and so would the instrument cluster. No codes present at all.
2015 Kia Optima Crank No Start Easy Fix
มุมมอง 1.3K2 หลายเดือนก่อน
In this video I show what it took to get this kia Optima to start and run, it was my first of its kind.
WorldPac STX2024 Training & Expo Event
มุมมอง 4132 หลายเดือนก่อน
In this video we show our great experience we had during our first STX event that was put on by WorldPac down in Nashville ,TN.
2016 Audi Q5 All Keys Lost BCM2 Read w/ Autel
มุมมอง 2.2K2 หลายเดือนก่อน
In this video I show the process of how to get an Audi with a locked BCM2 started by learning a key to it when you don't have any.
Scanning 1992 BMW 325 E30 Check Engine Light w/ Launch
มุมมอง 5582 หลายเดือนก่อน
Scanning 1992 BMW 325 E30 Check Engine Light w/ Launch
2017 Infiniti Q60 Intermittent No Start Diag & Fix
มุมมอง 1.8K2 หลายเดือนก่อน
2017 Infiniti Q60 Intermittent No Start Diag & Fix
2010 Ford F150 PCM Code P060A No Start Diag & Fix
มุมมอง 1.4K2 หลายเดือนก่อน
2010 Ford F150 PCM Code P060A No Start Diag & Fix
2013 Ford F150 No Start No PCM Communication Diag & Fix!
มุมมอง 2.5K2 หลายเดือนก่อน
2013 Ford F150 No Start No PCM Communication Diag & Fix!
2016 BMW Manual Shift Mode Activates on its Own
มุมมอง 7453 หลายเดือนก่อน
2016 BMW Manual Shift Mode Activates on its Own
Scope Lesson on How to Identify a Misfiring Cylinder
มุมมอง 2K3 หลายเดือนก่อน
Scope Lesson on How to Identify a Misfiring Cylinder
Chevy/GM Impala P0325 Knock Sensor Circuit Code Fix
มุมมอง 1.2K3 หลายเดือนก่อน
Chevy/GM Impala P0325 Knock Sensor Circuit Code Fix
How to Test For Clogged Catalytic Converters
มุมมอง 1.6K3 หลายเดือนก่อน
How to Test For Clogged Catalytic Converters
GM BCM CLONE WORK W/ OBDSTAR DC706 & AUTEL IM608
มุมมอง 3.2K3 หลายเดือนก่อน
GM BCM CLONE WORK W/ OBDSTAR DC706 & AUTEL IM608
2017 Volvo XC90 Crank No Start Diagnosis
มุมมอง 2.4K3 หลายเดือนก่อน
2017 Volvo XC90 Crank No Start Diagnosis
2016 Jeep Cherokee Misfire 2.4 Multiair
มุมมอง 1.9K4 หลายเดือนก่อน
2016 Jeep Cherokee Misfire 2.4 Multiair
Launch X431 Pro TT Features, Options & Capabilities
มุมมอง 8K4 หลายเดือนก่อน
Launch X431 Pro TT Features, Options & Capabilities
2013 Land Rover Evoque Hesitation on Acceleration
มุมมอง 2K4 หลายเดือนก่อน
2013 Land Rover Evoque Hesitation on Acceleration
2012 Honda Accord ODS/Airbag Codes Fix 85-64 & 81-64
มุมมอง 2K4 หลายเดือนก่อน
2012 Honda Accord ODS/Airbag Codes Fix 85-64 & 81-64
2013 BMW 528 N20 Misfire ComeBack Diagnosis
มุมมอง 3.2K4 หลายเดือนก่อน
2013 BMW 528 N20 Misfire ComeBack Diagnosis
I just have the valve replaced, but the AC still doesn't work. Now I'm wondering if they bent the pins?😕 2013 VW Passat. Do I have to replace the compressor it self?
Do you have contact for who remote into your laptop to program the car?
Was the tool DC706?
Thank you for making this video! I have the exact same issue. Ordered a new BCM and it will need ODIS programming as well. When you scanned the car for codes while it was in SAFE mode, did you get trouble codes from the BCM?
Nice video. I programmed an identical key for my E46 2 weeks ago. The key interferes with my bluetooth adapter that was just to the left of the radio and i decided to replace the oem radio with an android one. During the procedure my battery drained because stupid me worked with the interior lights on. Had to recharge the battery and everything worked ok for another week. Today, after driving 250 kms, the key didn't start the car. Fortunately i had my wallet key with me (glad i saw your video 2 weeks ago and decided to be cautious). So, my question is, did the problems get solved definitely with that car/key? I can remove the ews and force the key to sync again like you did, bit i am afraid the problem will appear again. I do not notice any battery problems after recharging but i didn't measure the voltage. Thank you.
Every year, 100,000 Mercedes owners are blind-sided with a $4-$5000 repair and swear off Mercedes forever. It is hard to imagine how many more lifelong Mercedes fans there would be if MB simply spot-welded the triggers on 2 million sets of camshafts every year. What's worse is the fact that they are well-aware of this persistent problem and would rather save $2 per car while setting the owner up for a complete screw-job.
Saved me from almost paying $500 in parts. Was about to buy a new PCM, a new alternator, a new starter, new battery 😂. It’s running, but I still have the codes, I’ll look into it more.
am working on a particular bmw in my shop presently the problem with the car is when you pack it over night it will hardly wake up the next day, I mean when you insert the smart key nothing will pop on the dash no ignition no crank but I have checked ur previous video on same issue when I checked the 2 wires on earth therminal no wire only, but I found 2 wire on positive therminal been removed already any help please I will appreciate tnx.
Does the DME code reset also apply/work on N52s? Thx
On many vehicles (e.g. V-6) the rear bank is located near firewall, under the cowl, and under the intake manifold. Too much work to remove all of that just to install spark plug. How do you deal with 'dat?
HI, thanks for your excellent videos, with this launch you can reset the counter after changing the Cerina additive (also called Eolis or Pat) for Citroen/Peugeot cars, thanks for any replies. 
I am assuming you get a fault light if the fuel injectors are not programmed correctly? Will this also work on the BMW N57 diesel engine?
Obdstar customer service is the worse in the industry. I emailed obdstar about a year ago with a problem on the p50 and here I am almost a year later and no response from them yet.
Same issue here with autel on reading eeproms and failing to verify read/write unless I remove eeprom.
Can you please help... I have a BMW 2014 X3 F25 the Electric Water Pump Bleeding was working fine twice. Then, it stop after I used the Blue Devil Head Gasket Sealer. The Engine getting hot. So, I changed the Thermostat and clean out the Reservoir Tank. Same issue. Should I change the Water Pump? Is there fuse that I should check? I got 3 Codes: 1) CD9010 LIN, Message: Electric Coolant Pump: Missing. DTC Status: Current 2) 1A2004 Electric Fan, Actuating Wire: Line Disconnection DTC Status: Current 3) 1A2002 Electric Fan, Actuating Wire: Short Circuit to Ground DTC Status: Current Please help :) Thank you & God Bless
My fob won't open or close my tailgate on my 2009 Mercedes GL 450?
Hey boss man I have been watching your videos with the vanos system and I have this car that is throwing a 113e01 same code you have. I have re flashed the DME to the latest program I could find on my autel 908. My part number is F001-23-07-530.I beleive I need to replace the valve tronic servo motors. Please let me know if you have the time.\
Nice job man
Thanks!
Smh
By the way I was able to fix my problem My battery voltage dropped to 9 volts while starting and I didn't have to buy a fuel pump I just needed a new battery 2013 ML550
Bro I got the same issue but I'm not getting codes for the fan? Is it the relay ? Or is it still the fan? I am pissed I can't figure this out
It looks like since compressors with solenoid vale always working summer and winter and only the flow of gas is controlled not the rotation and rotation never stops they break down and get damaged more than the compressors with clutch why they make this type of compressors.
Thanks for sharing
Thanks for watching!
They replaced an expensive car for a vacuum leak?? Ouch
How much Should A Locksmith charge for a Job like that?
Hi, I have a 2006 range rover sport diesel that is not engaging reverse, I took the valve body out and yellow and green soleniods are reading 6.7ohms while the black one is reading 10.7ohms. Are these normal values?
what diag tool are you using for the coding,
Autel scanner, any of the higher end autel with a current subscription should be able to do it, possibly launch scanners also.
What are these scopes/tools called?
the scope I use is from the company Pico, and the scanner is Autel
Geesh terrible delivery
says who
So, lesson to us, mere mortals: 1. Pretend I am just a dumb user / driver. Get in the car, look around, I might see some evidence of prior "work": relays lying around, Huge Colossal Parts Cannon lying on the floor, etc. 2. Do the basics first: check voltage DROP on fuses (takes a minute or two). Note: pulling fuses and relays is a 10000 year old profession, never dies. 3. Using the two previous Rules of Life, there will be no need for gizmos, expensive trinkets, etc.
if you can do this without gizmos and expensive trinkets to verify what isn't the problem, and what is...... than you are the most amazing diagnostician ever that no one has ever heard of, I suggest you start a channel to show us immortals how to do things right.
Hi friend. Question. I got a 2011 BMW 550i xdrive n63 engine. I put a new engine in 2 new catalytic. converter. But the car is shaking. And hot. Misfire 2/4 from the passenger side only. Do you know what cost that please??
what codes doe it have? do some basic testing for misfires to try and find the issue to start with
WOW, great video Sadel, anybody else (including me 😂) would probably go down a rabbit hole with this one.
😂 Yes, I almost did too !
Impressive!!
So if i have a u0100 missing communication with ecm would this fix work as a bypass?
no, the computer has to be able to communicate.
@@DTEAuto thanks for the reply. I used a jumper wire on the start/run relay which doesnt have 12v coming i to it, truck starts. Is that relay controlled by the pcm?
Nicely done Sadel! Interesting job with a twist. Loving the new channel music also. Favorite so far
Glad you like it!
Great job! Thanks for sharing!
Thanks for watching!
Impressive Sadel. Regards.
Thanks!
This isn't just a fix it video. This is a masterclass tutorial. Thanks for sharing. 👍
Thanks! Glad you enjoyed!
I completely agree 👍
Супер!Хорошая работа!
Fantastic job with finding out about the differences between the two modules (and the fix for it)! You didn’t panic, did the research and resolved the issue. A++!
I did start to question it lol
Perfect job💯 No scope today😅
Thank you, and yep no scope on this one
Thank u
Welcome, thank you for watching
I really like the thorough way you perform the tests. It would be even better to mount your camera on a tripod. The constant moving camera made me kind of seasick.
Thanks, Singh
MINI had a TSB for this issue. Their solution? Reprogram the DME 🤣
what's the tsb number?
Thanks, very informative
Surprised the other shops couldn't diagnose this.
same here
Nice finding 👌
thank you