--Disable and Re-Enable the Internal Battery via program logic-- Hold the JBL CONNECT button beside the power button, and volume up, until the fifth light flashes red. Then plug in the JBL if not already and power it on and do the key combo again to enable the internal battery again. -->This totally fixed my BT Connection issues and where the unit would Abruptly power down when connected via Bluetooth. Also it sound better too like it kinda sounded blown before idk maybe that like my placebo ears. I also did a reset though Bluetooth button and Volume + buttons together for 10 seconds
Jbl Xtreme is bass boosted so if you want to listen to like guitar and drums playing and you dont want to hear crazy boom (xd almost) every bass drum hit. I like to reduce bass sometimes
Don't put your JBL speakers in "Low Frequency" or "Bass Reduction" as some call it! It's a mode JBL uses to diagnose problems with the drivers of your speakers when you send them in for repair. Using this mode for general usage will almost always end up with permanent damage to the speaker.
I bought a f...JBL in Brazil the surprise was when l open the Xtreme 2 battery has a 1200 ma hx . I believe it's not the real one where can find the battery spec the same as1200 or can l replaced for another of 2600? Thanks very much can you help me to this replacement .p.wilson .😮
PieniuATV I hear this argument very often. What it does it that it disables the DSP processing, which indeed gets rid of the low-cut, making it go lower (Not 5 Hz, that isn’t even close to hearable with the human ear, let alone that a 3” driver can produce it. It only moves at 5Hz, but doesn’t produce sound), but it reduces bass a lot, because the bass boost that the Xtreme is known for has been programmed into the DSP. Which is what gets disabled when turning on that mode. Clavinetjunkie made some frequency response measurements of this, and there is a great loss in the bass, just that it reaches slightly deeper. There we go, cleared that up for you.
Just thought i’d add my 2 cents. the mode you mentioned, is called low frequency mode, and makes the speaker hit the low low notes instead of the standard bass notes in songs. if you play in that mode for too long, and go back into the original mode, the speakers will over time sound distorted and “crackled” if you will. it’s happened to both my jbl xtremes :D good video man!
This is bullshit ,its no "low frequency mode" this mode just turns off the limiter and eq ajusted in the speaker,but its true if you listen music with this mode on for too long the speaker may start to make cracking noise
That does not lower the bass, that activated the low pass frequency mode where it puts more emphasis on the lower frequencies (That can severely damage a speaker driver) I have a solid black XTREME and have also realized that it will make the high end just sound muddy and gross... When I got my speaker, I thought it was a fake because it was set to low pass frequency mode. This meant that it had no bass, didn't get as loud overall, and had crappy, muddy highs (It sounded like a beats pill lol, don't get triggered) I got so mad until i researched and learned what happend, that is when I turned the low pass off and got a real taste of this beasts bass and volume, love it!
I can't get any of these "tricks" to work on my extreme 2. Maybe some newer firmware stopped this stuff? Mine is only like 10 months old now from mid 2022.
1:20 it really doesn't limit the bass it's a low frequency mode which goes to the lowest range like 1 hz. I tried it on my flip 4 and gets from 20000 hz to 0 hz, but middle range bass (about 100hz) sound lower so maybe that's why you'll need more volume and a low range song to really appreciate the change
No it’s just a power safeguard to prevent damage to the speaker. It doesn’t change the frequency range but the lower frequencies are more audible because any safeguards (it also safeguards distortion so it’s not just a rattle or buzz down the low end) and actually reduces bass quality because of its buzzy quality and you could literally blow the speaker.
Hi on the box back sirde number will be there of jbl customer support call them they will further assist you or elsee email jbl support at india_csupport@harman.com
@dhuhhh what happened is that he turned on low frequency mode or low bass mode as some call it and this is a feature JBL uses to check what is wrong to the speakers. drivers Don't turn it on or use over 60% volume. If you use this mode in general it will damage your speaker permanently.
@@josephmacias2062 i had same issue with Charge 3. Bass mode destroyed speakers. Sounded like garbage. No sound quality at all. Speakers were blowed out. I took mesurments of speakers size and dimensions and ordered new ones from ebay. Cant tell the difference in base or higher tones comparing before.
When you do LFM (Low Frequency Mode is when you hold bluetooth and minus) the bass is quiet but when u turn it up! Ooo shit it gets out of control. Some times the speaker wven moves around.
Did you know that. You dont limit the bass. You make it wilder. You just dont notice until you max the volume on the speaker. Then the things will go crazy!
Nur Deutsche regen sich darüber auf wenn ein Deutscher Englisch spricht. Warum ist das so? Wo ist das Problem? Mit Deutschland geht es zu ende. Es sprechen halt viel mehr Menschen Englisch als Deutsch. Da muss man sich langsam mal global anpassen, die Kommunikation mit anderen Völkern einfacher machen. Vergesst Deutsch einfach und lernt Englisch.
@@mygiguser Thanks man! I discovered this yesterday and it's been playing on this setting since then, and i was wondering if there's any chance it could be affected
lol... And on the Jbl Boombox, the better db mode makes the bass even better and more dangerous. By meaning Dangerous. It just makes the Radiators go CRAZY and might break the speaker...
There is also a locking feature in it u have to press pause and volume plus button and then it will lock.. for unlock you have to plugin the charger and then press it again then it will unlock
Hi I have just purchased a new JBL Xtreme -- After un-boxing it had an initial factory charge that lasted for about 3 hrs - I drained the battery completely till the red light was blinking and then switched off the unit and connected the charger - the first 4 lights got solid bright within the first 45 min of charge and the 5th light kept on blinking - is this normal -- its now about 2 hours and the 5th light is still blinking - should i leave it to charge for more time - Please advise...
this can be a problem with the battery this happens sometimes with the models that they dont fully charge the battery is broken then you can fix it at jbl or the store you bought it
I've got a problem with my jbl xtreme speaker when its off turn on button is working but after that any of the buttons aren't working. Exept play/stop button which is working as turn off button giving kind of "boom" sound after pressing. Plz help i tried to discharge it completly and charge it again fully, even restet combination doesnt work...
does one of the usbs have the ability to stream music while charging? I really wish there was an aux / jack / line in of some sort... edit: nvm I have found a guy who shows there is an aux in :D is there any latency if I used this as my laptop speaker? this speaker seems perfect other than the issues with latency I know occur with bluetooth and lack of a jack...
The Bluetooth button end vollume down is setting the u turn the equalizer off of the speaker when u push the Bluetooth button end vollume up u have 3 modes( low bass high vocals, normal bass normal vocals, end as last pure bass low vocals.
@@matrihamiltonjr2230 hi. Thankz for answer. The volume is loud.volume is ok. But the bass decrease when charge 4 is at volume maximum. I have 2xcharge 4. How is the bass with the xtreme at maximum volume?
@@carlosvarela5367 I got my extreme 2 around 3 days ago but so far it's about the same as my flip 4 inside at home, but I can tell outside or a bigger the extreme will carry the sound further than the flip
I'm kinda a speaker nut. To be safe, I wouldn't use the "low frequency mode" to often, and DO NOT go above 60% volume. I have blown my fair share of speakers in my lifetime. I have never blown or cracked a speaker accidentally, without trying. From all my testing and fooling around, the bass actually cools the voice coil of certain drivers, but is extremely hard on the spider and cone. Depending on the design of the speaker (is it a full range, tweeter, mid range or woofer), some are designed for a very specific frequency range. For instance, if you input mid to high of a frequency through a subwoofer, you can damage the voice coil, as the subwoofer is not designed for those frequency's and heats up the voice coil very fast. This is why its essential to have what is known as a "crossover" or (high/low)pass filtration. Same goes for tweeters. Input to much low frequency through a tweeter, and its gone within seconds! Why? Because the tweeter can not physically react to low frequency, and so will over heat. Tweeters are designed to to produce high frequency that vibrate the driver millions of times a second, but only within a very specific range. Tweeters are cooled in a number of unique ways, but physically moving air is not one of them. Woofers move a lot of air, but its that movement that cools the voice coil. Now why is using "low frequency mode" dangerous? Simple fact, the unit was never designed to be used in this fashion. The drivers in the extreme 1/2/3 can handle way more amplification then what JBL offers, but its not the limitations of the drivers, its the amplifier/crossover. When you exceed the power limits of of any amplifier (distortion or clipping), the drivers will get double or triple the power (watts), as the input signal becomes unstable. This unstable signal will heat up the drivers voice coils via a soup of messy uncontrolled frequency, and will eventually either crack the driver (burnt voice coil) or completely blow it (toasted voice coil). It's always better to have to much amplified power (watts) than not enough! Distortion will kill speakers "faster" than having to much power. The cleaner the signal, the better. With that said, never exceed the amplified power rating (RMS) of any speaker.
Can someone please tell me how to turn back on the power save mode on my jbl charge 3. I somehow inadvertently turned it off and idk how to get it back on.
@mygiguser when do you recommend recharge jbl xtreme ?! so my battery don't die after 5 months or something , should i drain the whole battery first , then charge it from 0 to 100% ?
Am1rExpert i looked it up, and it is 40% charge at 15°C or 59°F that means if you look at the power LEDs, 2 of 5 on should be the best bet on storing the Xtreme or Xtreme2
Do you know how to remove the sounds of the flip 5 when power off/on and when connect? Or at least how to lower them because i can"t turn it on or off without waking up all my house when i want to listen music at the lowest level possible. I search how to do it on internet but there is nothing working. I cant' find the jbl connect app on the play store, i don't know if it's because i'm in France. This sound is really annoying. One thing is sure, jbl engineers are not using their product in everyday life or they had seen quickly that this sound is more annoying than useful. :(
@@luke4800 You can get rid of it. unfortunately i didn't remember how i did it and didn't find where is the answer of Harman support which tell me how to do it. As far as i remember it was pressing 2 button for 10 sec but i don't remember which one it was. Or you have an other option which is to download JBL CONNECT on app store and update the Flip 5 with it, then you will have an option to remove the startup sound. But at that moment my smartphone wasn't smart enough to use the app so i asked to the support and manage to turn off this sound. I should have reply to my own question here to keep a track of how to do it. :/ One thing is sure is that it's not bluetooth + vol down (low bass mode) or the volume up + play/ pause (hard reset). ^^
@@jblbasstester6198 What is the DSP ? what does it mean ? is it safe to use is it designed to be used ? Its not in the manual so I am assuming it is suppose to be some kind of like I dunno fixing making sure it works mode or something.
DSP stands for digital signal processing. Almost every big BT Speaker uses a DSP chip in order to modify sound signals. It counts to general hardware, which is the reason why it is not mentioned in the manual. JBL enabled a function for us to disable DSP, so that the speaker doesn't modify or limit sound signals. There are some speculations as to why JBL did this, but i think this is the reason: -Encourage market share simply by the fact that people make videos with this mode (same reason i started my channel) People are buying these speakers to mess around with them on YT Whether it is safe to use or not - depends on the speaker. From the Flip-Xtreme series you notice massive distortion when using this mode. The speakers can also bottom out. Powerful Amplifiers like on the Charge 4 are actually able to burn its OWN coil when playing a fixed low frequency and cutting cutting the cone out from the basket (so it doesn't cool by moving) This shows that it can be dangerous when using it at an extreme level. Don't be worried though: This can't happen if you don't cut out the paper of the speaker, because i've never actually seen it. Then we have the Boombox and Partybox It pretty much totally safe to use the DSP off mode on these. They have almost no distortion on maximum volume, which leads me to believe that they use the cheapest amplifiers possible, as they're not really powerful. Of course, again, you shouldn't directly play low frequencies (like a 50hz tone) at maximum volume, otherwise your amplifier can get really hot on these speakers. Small advice: These modes are pretty much useless if you want to purely listen to music. It reduces bass at lower volumes, makes all speakers sound kind of bad and undefined and makes some speakers distort on higher volumes. Of course there are people like me who use these modes for loudness purposes. The JBL Xtreme can get extremely loud when using this mode, but it distorts like crazy on higher volumes. I have to use an EQ to reduce bass to such a level that it won't distort, but there are downsides. -Worse sound quality (Bass is undefined, lower bass notes distort while mid bass is pretty muted; treble response is artifacty, and so on.) -Extreme Battery Drain -Possible damage to Tweeters when boosting treble in DSP off mode (one of the tweeters on my JBL Xtreme is broken, don't know whether it comes from using this method or not) In conclusion, just don't use DSP off mode if you normally want to listen to music.
Hi, thx for the useful vid! I have a bettery fail on exactly the same item/model. After watching your video, I have restarted the battery. Now its working more stable/doesnt turn off constantly. But the Leds have eventually stopped showing anything at all (lights are just off) Any advice on this failure? p.s. the failure has been since the moment I bought it, the leds weren’t working properly, but unfortunately I haven’t paid much attention to that by then.
mygiguser , thanks for the reply! unfortunately not, that seems a software bug or smth...actually its now showing 4 out of 5 lights shining, but it keeps turning off constantly. Any chance to reboot the systme for instance?
Why can't I get ANY of my Bluetooth devices to pair? I have deleted them, reset my phone, etc... And no matter what instructions I follow, the JBL Flip 3 is the most difficult to pair.
did anybody know how to go back to the previews firmware? because after I updated the bass go crazy and if u reduce it it sounds not good...I can't get around this problem!
You’re totally wrong. Pressing the Bluetooth and Volume Down buttons disables the DSP limiter which turns on Low Frequency Mode which makes it play more lower bass.
HuntieMC - Minecraft & more! Okay yeah right. I use this mode if im in the garden in the evening so the neighbors won’t get too mad because of the bass the xtreme produces. So the bass will reduce
God, thank you very much! I somehow f*cked up my JBL that the Bass was too extreme... I just wanted to know how I reset my JBL but than I saw how l can low the Bass in the video. Thank you!
Yes, Xtreme has Connect and therefore it can connect to a second device. That means you can play your music via two devices. Only the Xtreme2 or other devices with Connect+ can connect with more than 1 other Connect+ device.
Alright mygiguser So thats what i wanted to know about it so thx man real talk I have a cousin of mine he is in USA he bought 1 for me on Amazon so im in HAITI just waiting an occasion i meant some1 who can get down here and bring it for me this summer i will vibe out
I have it too Man gotta say best purchase ever At max volume got out of it around 7 hours or even more Plus its loud and clear Just dont activate bass mode and turn the volume loud ,keep it low if you want bass boost Best speaker around I dunno about the new xtreme tho... Maybe its better.
Toll... jetzt hast du mich auf die blöde idee gebracht tastenkombinationen auszuprobieren... habe ausversehen "Lautstärke -" und die "JBL connect" Taste gedrückt, und jetzt leuchtet beim laden das weiße licht auf dem On button... kann sie aber sobald sie weg vom Kabel ist nicht einschalten und nicht koppeln, wenn sie am Kabel hängt :/ irgendwelche Ideen dieses Problemm zu beheben? Edit: Problem gelöst:)
--Disable and Re-Enable the Internal Battery via program logic--
Hold the JBL CONNECT button beside the power button, and volume up, until the fifth light flashes red. Then plug in the JBL if not already and power it on and do the key combo again to enable the internal battery again.
-->This totally fixed my BT Connection issues and where the unit would Abruptly power down when connected via Bluetooth. Also it sound better too like it kinda sounded blown before idk maybe that like my placebo ears.
I also did a reset though Bluetooth button and Volume + buttons together for 10 seconds
What kind of human being wants to limit the bass?
Jbl Xtreme is bass boosted so if you want to listen to like guitar and drums playing and you dont want to hear crazy boom (xd almost) every bass drum hit. I like to reduce bass sometimes
GreenPawWolf furries are everywhere.
I‘m one too :D
GreenPawWolf my neighbor.
neighbors arent humans
GreenPawWolf Furries literally are cancer cells y'know
Don't put your JBL speakers in "Low Frequency" or "Bass Reduction" as some call it! It's a mode JBL uses to diagnose problems with the drivers of your speakers when you send them in for repair. Using this mode for general usage will almost always end up with permanent damage to the speaker.
So just play in normal mode ?
Bass reduction is not the same as low frequency
🥺.... to late🥺
@@rebeckaeriksson8583F
@@nurholik8949 yes
Please how do I increase my JBL Xtreme 3 Bass the Bass go off from 60% volume I have to put it against wall please any help
Secrets cause who reads manuals these days
Lucky-boy 128 hah thats true :D
@@japeehhi5457 I love this comment, Lucky-boy! I write software and user manuals. I'm wasting my time on the manuals. No one reads them!
Hahaha 😂
@@davidlincoln78240 i read them i like to read manuals
These are not on the manual, the manual only lists obvious things that are not useful for the average user.
I bought a f...JBL in Brazil the surprise was when l open the Xtreme 2 battery has a 1200 ma hx . I believe it's not the real one where can find the battery spec the same as1200 or can l replaced for another of 2600? Thanks very much can you help me to this replacement .p.wilson .😮
That's not true, the bluetooth and volume down button turns on low bass mode (where the speaker can go down to 5hz) but does not reduce the bass.
PieniuATV thats true ...
There are 4 modes with the bt and - buttons
PieniuATV I hear this argument very often. What it does it that it disables the DSP processing, which indeed gets rid of the low-cut, making it go lower (Not 5 Hz, that isn’t even close to hearable with the human ear, let alone that a 3” driver can produce it. It only moves at 5Hz, but doesn’t produce sound), but it reduces bass a lot, because the bass boost that the Xtreme is known for has been programmed into the DSP. Which is what gets disabled when turning on that mode. Clavinetjunkie made some frequency response measurements of this, and there is a great loss in the bass, just that it reaches slightly deeper. There we go, cleared that up for you.
PieniuATV it is true. On my charge 2+ it limites the bass too.
PieniuATV It Turns off DSP, Reducing bass in the mid 60hz and allows down too 5hz in the process because it removes frequency protection
Bass reduction hack doesn't work on my xtreme 2. My son tried to show it to me to no avail. Does the 2 have different secrets??
Just thought i’d add my 2 cents. the mode you mentioned, is called low frequency mode, and makes the speaker hit the low low notes instead of the standard bass notes in songs. if you play in that mode for too long, and go back into the original mode, the speakers will over time sound distorted and “crackled” if you will. it’s happened to both my jbl xtremes :D good video man!
This is bullshit ,its no "low frequency mode" this mode just turns off the limiter and eq ajusted in the speaker,but its true if you listen music with this mode on for too long the speaker may start to make cracking noise
*BEST CHANNEL ON TH-cam! Please Next Video How to Charge Phone! Please!!!*
BassCheff 😂
TRUE af
There are still secrets.
You need to collect 2 notebooks before you can charge your phone
Just use Google
What do you think the best battery replacement for the JBL Xtreme ?
That does not lower the bass, that activated the low pass frequency mode where it puts more emphasis on the lower frequencies (That can severely damage a speaker driver) I have a solid black XTREME and have also realized that it will make the high end just sound muddy and gross... When I got my speaker, I thought it was a fake because it was set to low pass frequency mode. This meant that it had no bass, didn't get as loud overall, and had crappy, muddy highs (It sounded like a beats pill lol, don't get triggered) I got so mad until i researched and learned what happend, that is when I turned the low pass off and got a real taste of this beasts bass and volume, love it!
So it's better only to modificate the bass with an equilizer on the mobile phone?
Will using an equalizer app damage the speaker at all?
@@SpeciaListMK Yes, the best app is poweramp
@@Penelope416 Should be fine t tweak the EQ on app
I can't get any of these "tricks" to work on my extreme 2. Maybe some newer firmware stopped this stuff? Mine is only like 10 months old now from mid 2022.
great!!
q. i try to connect a usb disk with mp3 and i cant hear nothing.what can i do?
the USB is only for internal updates and service, it cannot play mp3 via USB. you need a smartphone
1:20 it really doesn't limit the bass it's a low frequency mode which goes to the lowest range like 1 hz. I tried it on my flip 4 and gets from 20000 hz to 0 hz, but middle range bass (about 100hz) sound lower so maybe that's why you'll need more volume and a low range song to really appreciate the change
No it’s just a power safeguard to prevent damage to the speaker. It doesn’t change the frequency range but the lower frequencies are more audible because any safeguards (it also safeguards distortion so it’s not just a rattle or buzz down the low end) and actually reduces bass quality because of its buzzy quality and you could literally blow the speaker.
Rubbish
Hi
I have JBL Xtreme one year old and now days it getting off after 4-5 min while playing in Bluetooth mode.
How can I resolve this issue.
Prakash Acharya probably needs a new battery
Hi on the box back sirde number will be there of jbl customer support call them they will further assist you or elsee email jbl support at india_csupport@harman.com
i have the same problem did you find a solution ?
I have the same problem
People be carefull doing this. I did it and this was the end of my JBL extreme!!!!
😢
@dhuhhh what happened is that he turned on low frequency mode or low bass mode as some call it and this is a feature JBL uses to check what is wrong to the speakers. drivers Don't turn it on or use over 60% volume. If you use this mode in general it will damage your speaker permanently.
So what if I do that how do I uh do it
@@josephmacias2062 i had same issue with Charge 3. Bass mode destroyed speakers. Sounded like garbage. No sound quality at all. Speakers were blowed out. I took mesurments of speakers size and dimensions and ordered new ones from ebay. Cant tell the difference in base or higher tones comparing before.
What the deal with speakers no being able to replay tracks? Its like a future car that cant drive in reverse
What do you mean with that lmao????
Does this not work on the xtreme 2 or something? It’s not making a difference on mine
Can this work for JBL Charge 3?
When you do LFM (Low Frequency Mode is when you hold bluetooth and minus) the bass is quiet but when u turn it up!
Ooo shit it gets out of control.
Some times the speaker wven moves around.
Please help I puch the connect button and volume up and my JBL charge 3 is shutdown and it is not ON again.
hey, i have an issue, a "bluetooth' button on my jbl xtreme is broken, how can i make a
membranes turn on?
Best Xtreme 1 & 2 Video
When you press bluetooth button and volume down button, it activates low frequency mode.
Does anyone know what type of charger this speaker uses since I have lost my one and cannot find it on the internet.
Yes, someone will surely know
Did you know that. You dont limit the bass. You make it wilder. You just dont notice until you max the volume on the speaker. Then the things will go crazy!
What size drives are inside. I need to replace the speaker
Sometimes i dont have connect...Suddenly no music....Can somebody help me ?
1:10 that mode enables dsp processing
Martin Lavrič disables+
Disables*
Alter schon wieder so ein deutscher der Englisch spricht
Für nen deutschten hat der aber ganzschön amerikanische steckdosen 🧐
Es kann ja sein dass ein deutscher in Amerika wohnt oder nicht?
Auf jedenfall MUSS DAS EIN DEUTSCHER SEIN
Gerrit Harteveld fuck off
Ja hab ich mir auch gedacht xD
Nur Deutsche regen sich darüber auf wenn ein Deutscher Englisch spricht. Warum ist das so? Wo ist das Problem? Mit Deutschland geht es zu ende. Es sprechen halt viel mehr Menschen Englisch als Deutsch. Da muss man sich langsam mal global anpassen, die Kommunikation mit anderen Völkern einfacher machen. Vergesst Deutsch einfach und lernt Englisch.
is it possible to damage the bass areas while having them full powered?
Oh yes it is possible with any speaker. Depending on the music you can damage them.
@@mygiguser Thanks man! I discovered this yesterday and it's been playing on this setting since then, and i was wondering if there's any chance it could be affected
why it is al about BASS
Do you have any idea how to fix if jbl extreme shuts down everytime I turn the volume up more than half. Thank you.
Have you tried with the charger connected? Does it still do that? If not i would guess it's a weak battery.
mygiguser yes i tried it. Thank you. I need to replace the battery.
Ace Winfield Loyola th-cam.com/video/ppmBDg8pd7E/w-d-xo.html
Ace Winfield Loyola yes please, mine doing the same
I can help u tru my facebook
My power button broken out...
Plz say if any alternative is there.
Yes
I have an old model of jbl speaker it won't turn off. How do I reset it.
It power. Volume, connect and call button.
What model?
@@mygiguser charge 2 plus
lol... And on the Jbl Boombox, the better db mode makes the bass even better and more dangerous. By meaning Dangerous. It just makes the Radiators go CRAZY and might break the speaker...
There is also a locking feature in it u have to press pause and volume plus button and then it will lock.. for unlock you have to plugin the charger and then press it again then it will unlock
My jbl boombox is locked😭😭😭 help please
Why do we have crazy bass or zero bass, why no 2nd mode with 50% of bass?
That indeed is a good question!
It's not active subwoofers. It's passive radiator woofers! That's their secret! 😉
Anyway, I like this technic! The sound is the most important thing, so they have sucess with that!
Bro tell me bass music name please please
Bro, its in the description
@@mygiguser thanks bro
Hi I have just purchased a new JBL Xtreme -- After un-boxing it had an initial factory charge that lasted for about 3 hrs - I drained the battery completely till the red light was blinking and then switched off the unit and connected the charger - the first 4 lights got solid bright within the first 45 min of charge and the 5th light kept on blinking - is this normal -- its now about 2 hours and the 5th light is still blinking - should i leave it to charge for more time - Please advise...
Riel Fernandes yes, that’s normal. The fifth LED blinks only when the battery is 100% full.
this can be a problem with the battery this happens sometimes with the models that they dont fully charge the battery is broken then you can fix it at jbl or the store you bought it
I've got a problem with my jbl xtreme speaker when its off turn on button is working but after that any of the buttons aren't working. Exept play/stop button which is working as turn off button giving kind of "boom" sound after pressing. Plz help i tried to discharge it completly and charge it again fully, even restet combination doesnt work...
does one of the usbs have the ability to stream music while charging?
I really wish there was an aux / jack / line in of some sort...
edit: nvm I have found a guy who shows there is an aux in :D
is there any latency if I used this as my laptop speaker?
this speaker seems perfect other than the issues with latency I know occur with bluetooth and lack of a jack...
there is an aux in on the extreme, what are you on about?>
vol- and play button?
factory reset
PioneloxShoty no lol. Pause button and vol+ button is reset
yea i wrote it quick, my bad
Sir how test water this jbl
The Bluetooth button end vollume down is setting the u turn the equalizer off of the speaker when u push the Bluetooth button end vollume up u have 3 modes( low bass high vocals, normal bass normal vocals, end as last pure bass low vocals.
kr3at1vek1ll3rz how do you know this? Is there an official manual for this online?
mygiguser i have the same speaker^^
mygiguser when you turn the equalizer off the music is how your phone send it not changed vor better sound inprovements
mygiguser end how i kno it i saw it on TH-cam
kr3at1vek1ll3rz mine has like 4 or so modes to cycle through. I updated it through the JBL app.
Does the xtreme bass decrease at maximum volume like charge 4 does?
On mine the volume is louder one below max volume. If that's what you mean
@@matrihamiltonjr2230 hi.
Thankz for answer.
The volume is loud.volume is ok.
But the bass decrease when charge 4 is at volume maximum.
I have 2xcharge 4.
How is the bass with the xtreme at maximum volume?
@@carlosvarela5367 I got my extreme 2 around 3 days ago but so far it's about the same as my flip 4 inside at home, but I can tell outside or a bigger the extreme will carry the sound further than the flip
I'm kinda a speaker nut. To be safe, I wouldn't use the "low frequency mode" to often, and DO NOT go above 60% volume.
I have blown my fair share of speakers in my lifetime. I have never blown or cracked a speaker accidentally, without trying. From all my testing and fooling around, the bass actually cools the voice coil of certain drivers, but is extremely hard on the spider and cone. Depending on the design of the speaker (is it a full range, tweeter, mid range or woofer), some are designed for a very specific frequency range. For instance, if you input mid to high of a frequency through a subwoofer, you can damage the voice coil, as the subwoofer is not designed for those frequency's and heats up the voice coil very fast. This is why its essential to have what is known as a "crossover" or (high/low)pass filtration. Same goes for tweeters. Input to much low frequency through a tweeter, and its gone within seconds! Why? Because the tweeter can not physically react to low frequency, and so will over heat. Tweeters are designed to to produce high frequency that vibrate the driver millions of times a second, but only within a very specific range. Tweeters are cooled in a number of unique ways, but physically moving air is not one of them. Woofers move a lot of air, but its that movement that cools the voice coil.
Now why is using "low frequency mode" dangerous? Simple fact, the unit was never designed to be used in this fashion. The drivers in the extreme 1/2/3 can handle way more amplification then what JBL offers, but its not the limitations of the drivers, its the amplifier/crossover. When you exceed the power limits of of any amplifier (distortion or clipping), the drivers will get double or triple the power (watts), as the input signal becomes unstable. This unstable signal will heat up the drivers voice coils via a soup of messy uncontrolled frequency, and will eventually either crack the driver (burnt voice coil) or completely blow it (toasted voice coil).
It's always better to have to much amplified power (watts) than not enough! Distortion will kill speakers "faster" than having to much power. The cleaner the signal, the better. With that said, never exceed the amplified power rating (RMS) of any speaker.
My jbl xtreme 2 speaker doesn't have startup sound☹️ help me to fix it.
fake speaker?
Try to download jbl app and you can setup this there..
Is there any difference between the camo and the black?
no, just the looks
What is the name of song track your playing ????
Darude - sandstorm
MrLatinLingo 42C - Chelle Ives
@@mygiguser ...Thanx dude !!!!!
can jbl xtreme pairing to jbl xtreme?
mas dodik DA yes!
Having the Xtreme during 2 years , knowing that the day i'm selling it for the BOOMBOX
I should update the xtreme to connect + ?
kiss csapat no, that doesn’t work.
JBL stated you can’t do that due to its hardware.
Geht das auch mit teufel boomster ng irgendwie denn bass ausschalten?
TandJzocken YT womit?
@@mygiguser ich meine ob man bei dem teufel boomster NG auch die bass sperre ausschalten kann
Hat der nicht ne Taste (SUB) wo man die Lautstärke erhöhen kann?
@@mygiguser ja hat er aber kann man die eingebaute bass sperre die eingreift aus schalten
Is iT save to limited THE bass??
Eine Frage....wie kann man auf die Xtreme neues Update laden??
Navy man mit der JBL app per Bluetooth verbinden
Can someone please tell me how to turn back on the power save mode on my jbl charge 3. I somehow inadvertently turned it off and idk how to get it back on.
@mygiguser when do you recommend recharge jbl xtreme ?! so my battery don't die after 5 months or something , should i drain the whole battery first , then charge it from 0 to 100% ?
Am1rExpert i looked it up, and it is 40% charge at 15°C or 59°F that means if you look at the power LEDs, 2 of 5 on should be the best bet on storing the Xtreme or Xtreme2
Do you know how to remove the sounds of the flip 5 when power off/on and when connect?
Or at least how to lower them because i can"t turn it on or off without waking up all my house when i want to listen music at the lowest level possible.
I search how to do it on internet but there is nothing working.
I cant' find the jbl connect app on the play store, i don't know if it's because i'm in France.
This sound is really annoying.
One thing is sure, jbl engineers are not using their product in everyday life or they had seen quickly that this sound is more annoying than useful. :(
You can’t get rid of the startup sound. Just turn it on and shove it under your bed sheets that will mute most of it lol
@@luke4800 You can get rid of it.
unfortunately i didn't remember how i did it and didn't find where is the answer of Harman support which tell me how to do it.
As far as i remember it was pressing 2 button for 10 sec but i don't remember which one it was.
Or you have an other option which is to download JBL CONNECT on app store and update the Flip 5 with it, then you will have an option to remove the startup sound.
But at that moment my smartphone wasn't smart enough to use the app so i asked to the support and manage to turn off this sound.
I should have reply to my own question here to keep a track of how to do it. :/
One thing is sure is that it's not bluetooth + vol down (low bass mode) or the volume up + play/ pause (hard reset).
^^
Whats the difference between vol+ and play/pause vs vol+ and power
I think is to lock d speaker
I have a problem with My JBL GO 2
It got stuck on FM radio like its looking for stations can anyone help ?
Hi
I pressed the vol.up and the jbl connect button for 10 sec and my xtreme doesnot working i pushing the buttons but not responding what can i do?
Csergõ Olivèr Bro you had to press the vol up and connect button for 3 sec to knew a filmware version, not for 10 sec...
Where did you get JBL Xtreme with camo design?
Bros Mario i got it at Bestbuy in the store
@@mygiguser Thanks
Its a skin
"fp" the bass doesn't just turn off. there is a thing calld low frequency mode
5 _lol low frequency is for more bass not les bass
It‘s not called low frequency mode.
This mode disables the dsp.
@@jblbasstester6198 What is the DSP ? what does it mean ? is it safe to use is it designed to be used ? Its not in the manual so I am assuming it is suppose to be some kind of like I dunno fixing making sure it works mode or something.
DSP stands for digital signal processing.
Almost every big BT Speaker uses a DSP chip in order to modify sound signals.
It counts to general hardware, which is the reason why it is not mentioned in the manual.
JBL enabled a function for us to disable DSP, so that the speaker doesn't modify or limit sound signals.
There are some speculations as to why JBL did this, but i think this is the reason:
-Encourage market share simply by the fact that people make videos with this mode (same reason i started my channel)
People are buying these speakers to mess around with them on YT
Whether it is safe to use or not - depends on the speaker.
From the Flip-Xtreme series you notice massive distortion when using this mode. The speakers can also bottom out.
Powerful Amplifiers like on the Charge 4 are actually able to burn its OWN coil when playing a fixed low frequency and cutting cutting the cone out from the basket (so it doesn't cool by moving)
This shows that it can be dangerous when using it at an extreme level.
Don't be worried though:
This can't happen if you don't cut out the paper of the speaker, because i've never actually seen it.
Then we have the Boombox and Partybox
It pretty much totally safe to use the DSP off mode on these.
They have almost no distortion on maximum volume, which leads me to believe that they use the cheapest amplifiers possible, as they're not really powerful.
Of course, again, you shouldn't directly play low frequencies (like a 50hz tone) at maximum volume, otherwise your amplifier can get really hot on these speakers.
Small advice:
These modes are pretty much useless if you want to purely listen to music.
It reduces bass at lower volumes, makes all speakers sound kind of bad and undefined and makes some speakers distort on higher volumes.
Of course there are people like me who use these modes for loudness purposes.
The JBL Xtreme can get extremely loud when using this mode, but it distorts like crazy on higher volumes. I have to use an EQ to reduce bass to such a level that it won't distort, but there are downsides.
-Worse sound quality (Bass is undefined, lower bass notes distort while mid bass is pretty muted; treble response is artifacty, and so on.)
-Extreme Battery Drain
-Possible damage to Tweeters when boosting treble in DSP off mode (one of the tweeters on my JBL Xtreme is broken, don't know whether it comes from using this method or not)
In conclusion, just don't use DSP off mode if you normally want to listen to music.
MY Personal Spin i have added something to my comment.
It is pretty important, so reading it is a good idea
El único video util de los 1000 que vi!!! Graciassss
song?
Hi, thx for the useful vid!
I have a bettery fail on exactly the same item/model. After watching your video, I have restarted the battery. Now its working more stable/doesnt turn off constantly.
But the Leds have eventually stopped showing anything at all (lights are just off)
Any advice on this failure?
p.s. the failure has been since the moment I bought it, the leds weren’t working properly, but unfortunately I haven’t paid much attention to that by then.
Vadim Chuchkov maybe a loose wire?
mygiguser , thanks for the reply!
unfortunately not, that seems a software bug or smth...actually its now showing 4 out of 5 lights shining, but it keeps turning off constantly. Any chance to reboot the systme for instance?
For JBL 4 its not working ?
what is JBL 4?
Why can't I get ANY of my Bluetooth devices to pair? I have deleted them, reset my phone, etc... And no matter what instructions I follow, the JBL Flip 3 is the most difficult to pair.
Theresa Myslinski one possible problem could be interference. Try to pair at a different location.
did anybody know how to go back to the previews firmware? because after I updated the bass go crazy and if u reduce it it sounds not good...I can't get around this problem!
poly nominal there’s no way to downgrade. Everything is controlled by the JBL app.
Does it works for charge 3 to?
Niels Linders don’t know, it’s possible. i don’t have one.
You’re totally wrong. Pressing the Bluetooth and Volume Down buttons disables the DSP limiter which turns on Low Frequency Mode which makes it play more lower bass.
HuntieMC - Minecraft & more! Bullshit
Im sexy and i show it if you won't believe me then its fine but i'm telling the truth :)
HuntieMC - Minecraft & more! Okay yeah right. I use this mode if im in the garden in the evening so the neighbors won’t get too mad because of the bass the xtreme produces. So the bass will reduce
Im sexy and i show it yeah the mid bass will reduce and also the punch will reduce because it will start to play some low bass notes lol
HuntieMC - Minecraft & more! That sentence makes sense but when i let the equalizer play on a lower frequency the bass will get heavier and louder
Does the firmware check works on flip 4
PaXen yes and mine says 3.2.0
I have checked this too but i dont think that we will receive a update for our flip 4
Yes it works my speaker says 3.2.0
Mine says 3.2.0 too
how do i repair a crackling sound on JBL charge 3 speakers?
oliver olie it’s water damage that’s happened to mine
@@georgerobinson4125 how will i stop the crackling sound?
What is the service button in Xtreme
Vikas Sharma what service button?
God, thank you very much! I somehow f*cked up my JBL that the Bass was too extreme... I just wanted to know how I reset my JBL but than I saw how l can low the Bass in the video. Thank you!
the low bass is worse bc it will play low hz and will break it EVEN more
Anyone knows if i connect boombox 1 and xtreme 1?
Yes, someone will know
What song?
GamingForLife 42C Chelle Ives
Anyone Know how i do on off Sound Turn off ?
I think he just switched low frequency mode off so the bass was reduced
Am I right?
No
I think he turned it on and it got quieter because the low bass took over
Sorry to tell u but that doesn't limit the bass that makes it go into low frequency mode which is low bass notes at higher volumes
It's for lower hz songs where the bass is slightly hearable on regular mode
thanks for the info, you are the best! i have jbl extreme1 and i like it
My jbl extreme is keep turning off by itself need help please
R6 Dropout does it do it when the charger is connected?
mygiguser no I reset it and everything and whenever I play it without the charger it turns off by itself
He's not even limiting the bass he's just turning on Low Frequency Model or LFM
M'y jbl dont want power i mais it at charge it laghting ans dont want working i mais restart but she dont want warking plz help me
Ayman Soltani probably a bad battery, you need to replace the batteries!
Can the extreme connect and play through two blue tooth devices??
Yes, Xtreme has Connect and therefore it can connect to a second device. That means you can play your music via two devices. Only the Xtreme2 or other devices with Connect+ can connect with more than 1 other Connect+ device.
Whats the different of 7.7 n 6.6 ?????is 7.7 better than 6.6 ?
Anyone can explain...
Thankyou
Yes better, if there is a newer version, one can assume that JBL made changes to their software to improve the speaker.
@@mygiguser I push , lower vol n connect for 3 s, n it said 6.7 ...why not 7.7 ?
Mine is extreme black colour
Look man i want to know if JBL EXTREME has battery issue problem, some say it doesnt make long time playing is that true?? Be honest no lies please
Vancral Charles i have only one Xtreme, and i never had battery problems. With other words, i don’t know if there are problems out there.
Alright mygiguser
So thats what i wanted to know about it so thx man real talk
I have a cousin of mine he is in USA he bought 1 for me on Amazon so im in HAITI just waiting an occasion i meant some1 who can get down here and bring it for me this summer i will vibe out
I have it too
Man gotta say best purchase ever
At max volume got out of it around 7 hours or even more
Plus its loud and clear
Just dont activate bass mode and turn the volume loud ,keep it low if you want bass boost
Best speaker around
I dunno about the new xtreme tho... Maybe its better.
I also have an xtreme. I think I own it like 6 months and I never had any issues with the battery or smthg else
N_eis alright so still waiting for mine coming on this summer, I'm from Haiti. I will vibe out with my JBL EXTREME
Does the firmare check works on JBL Flip 3??
Michał Chełminiacki i don’t have flip3, but i think it does
@@mygiguser ok, thanks :D
Low frequenty mode.... It's not a secret.... Pls next video how to charge a phone.
Toll... jetzt hast du mich auf die blöde idee gebracht tastenkombinationen auszuprobieren... habe ausversehen "Lautstärke -" und die "JBL connect" Taste gedrückt, und jetzt leuchtet beim laden das weiße licht auf dem On button... kann sie aber sobald sie weg vom Kabel ist nicht einschalten und nicht koppeln, wenn sie am Kabel hängt :/ irgendwelche Ideen dieses Problemm zu beheben?
Edit: Problem gelöst:)
Dann ist ja alles in Butter?
@@mygiguser Jop ^^
Volume down/Bluetooth is low frequence mode or sompething
Could you make a video with jbl go secrets plz
nice show
Thanks for this!! This was helpful!!
its not low bass mode
it just makes it so you can have lower frequencies
name of the song pls?
Martin Valovič 42 c chelle iven you can thank me by going to festivals men!!!!
@@hallobyebye699 can find it under that
Then u said that limits the bass really adds more bass
IT CALLED LOW FREQUENCY MODE
How I can update my to 7.7 ?
Pedro Hernandez use a smartphone and the JBL app.
Okay thanks but I have to used a USB cable for that or not ?