If you MUST carry out this dangerous repair, at least offset the two joins so that they are not alongside one another and cannot short across. Secondly, don't do this.
And double, triple the heatshrink tubing, and use bigger ones to cover everything instead of using cotton and tape. Filling larger heatshrink tube with hot glue can be used to help with strain relief too.
When I was a kid, my father used to put wires straight into the power outlet if there was no plug. Old cables with thick copper veins and 230V going through them. I felt uncomfortable seeing it, yet after many years I do believe it was a safer thing than what you did here, lol. The worst thing about it is the fact it gives you a sense of safety.
I am glad you found a solution that worked for you, but it's always best to use proper safety measures when dealing with electricity! Stay safe out there! ⚡️
It may look safe and probably it even is save, but when you have a fire in the house, the insurance will not pay a penny when this is found in your house. even when it was not the real course of the fire. A replacement is so cheap, you do not want to take the risk.
This is a highly dangerous bodge job which should not be carried out except in an emergency when buying a new plug or even a complete lead is not possible. A simpler temporary repair is to use a connector block. Ugly but safer
It is an excellent video recording, but the whole point on safety is missing. If someone follows the instructions perfectly, they end up with a very dangerous setup. No, unless this is an emergency requirement, it should never be done. Buy a replacement plug that was designed to work better and last longer. If someone repairs an electrical cord in this fashion, they end up having an electrical failure and possibly a fire hazard.
@@markswanson6898 Save the Earth, but use your brain first. The way of "repairing" gives dangerous utility an can cost somebody's life. It is better to throw the plug to ♻️ and use replacement plug. Really.
Hey kids you can use your playstation now. Tug on the cord like you usually do (how it broke in the first place). Reach around the back of the cabinet to plug it in with your wet hands. I have done this (remote location not near stores) with offset joins and heavy shrink over the top and still didn't trust it so got rid of it. I only watched this to the end to see how bad it really was. I noticed slight nick in the insulation for starters - prone to break/shortcircuit even if not conductive just yet.
@@CreativeMaster999 If you reallllllly cared about safety you would take this video down. Sure, make videos showing how to fix things, but when you get 500 comments showing it AINT GOOD, TAKE IT DOWN!!! Make a new one with the offset mentioned, use a real wire stripper that won't nick the insulation, don't wrap it with thread, don't wrap it with rubber tape, and there should be something to replace the grip you cut off.
@@CreativeMaster999 Are you for real, talking about safety, when you are carrying out a very dangerous repair like this. You should be ashamed of yourself for being so stupid.
I never had any luck with off the shelf plug ends. Even when I paid $200 to get a bunch of my cords fixed. I do a similar method as this with more reinforcement than the video shows. Nothing you buy off the shelf is engineered to work flawlessly. Everything is engineered to be just good enough to sell at the price people are willing to pay. Moreover, even the plug ends they sell that do not really work, are often as expensive as getting a new cord.
I use several extension cords for work each day and use about 250 feet of them on the weekends to mow my 75 feet by 400 feet deep lawn, since I have so many cords, and a corded lawn mower doesn't stall on long grass like my riding and push gas mowers, and the electric cuts the lawn shorter and the lawn looks better. My lawn grows an inch per day and I need to cut it 2 times a week with my gas mowers and once with the electric. Also, the thinker the copper wire, the more brittle and more quickly we get cord breaks. The thick wire is nearly impossible to get a good plug replacement. So slicing and soldering has been the only practical solution. It seems like a good thick cord does not take very long before needing a repair, more so than the thin. The wife and son refuse to mow rationally, from the outlet outwards, so the cord cannot get run over. I think they also purposely run over the cord with the lawn mower as an excuse not to mow, just as they use the excuse that they can't get the fas mowers started. Thus a seemingly constant cord repair is the norm.
@@CreativeMaster999 "quick" is a big word here but can you tell us the cost of therepair ? soldering iron consumption + Solder Wire, lighter, heat-shrinkable sleeves, tape and unvaluable time. Of course i suppose you already have all necessary tools
Not good! Too many chances of nicks in the wire and short circuits. Far easier and safer to buy a new plug and connect the appliance end of the cord to it.
A new plug would be best, but he used a standard solder splice. I would suggest that he also use shrink wrap tape over the electrical tape to make for a stronger safer splice.
The method shown in the video should only be used in extreme cases and away from children. Remember to always prioritize safety when dealing with electrical repairs! ⚠️🔌
I've done stuff like that many times... but only on low-voltage systems like battery powered kids toys or led light chains. Even then I cut the cables to different length so the soldered cables would not touch each other even if insulation would fail. Never ever I would try this on a power cable!!! I like the place I live a lot, I don't wanna burn it...
Funny thing... "Low Voltage" DC toys can catch on fire easier than single phase given a bad connection. I've seen a house alarm wired with single core wire across a ceiling space... the insulation had melted of nearly it's entire length.
You are working totally unsafe. By cutting towards the finger you are setting a bad and dangerous example. Instead of heating the heat shrink tubing, you have blackened it with flame, soot has settled, i.e. carbon, which in combination with the adhesive of the insulating tape creates a conductor of electricity - this is a direct path to fire. The original plug has an element that makes it easier to remove from the socket without pulling the cable, you cut it out and did not recreate it. You should be banned from publishing nonsense for the safety of people and equipment.
My old woodwork teacher always used to repeat the mantra, ‘Hands behind the cutting edge.’ So much so that my wife repeats it to me now, as I was always saying it out loud. 🤣
I recently cut my hedge trimmer mains led, with the trimmer! I bought an external in line mains connector, cut out the damaged cable section and fitted the connector in its place. Just make sure that the prong side is on the appliance side. Dave UK.
I appreciate your concern for safety! In the video, I demonstrate a safe and effective way to fix a broken electrical plug. Always prioritize safety first when attempting any repairs. 🔌👍
@@CreativeMaster999 Você achou essa forma segura? E ainda se intitula mestre? Me desculpa, mas todo essa trabalho com solda é queimando e fio. É 5 reais um plug novo meu amigo. Essa borracha de proteção de fábrica é testada para isolar o calor da amperagem elétrica. Isso é uma GAMBIARRA e muito trabalhosa.
Replacing a plug was one of the requirements for advancing a rank when I was a Cub Scout. 60 years ago. Of course, it was a much more important life skill back then…
My grampa would be so proud of you. We used to fix everything, whereas now we usually just buy a new one. Grampa is rolling in his grave... but in the factory they stamp out a new cord in exactly 2.5 seconds, and this took 5 minutes to repair, not counting 3 hours for trips to the electronics store for soldering iron, solder, and shrink-wrap; to the hardware store for electrical tape; the fabric store for thread; the department store for superglue... It really doesn't make sense to fix a lot of broken junk unless you're stuck in some remote location and need that lamp in a hurry. And have all that stuff on hand.
2:57 cold solder joint. Not good at all. At least use some flux and not brush the solder over the wires. Afterwards, throw it all away and buy a new cord/appliance. I would not recommend anyone using this method.
@@CreativeMaster999 Yeah, but the last will be the result of the first and the biggest problem is that the insurance will not pay a penny when this was found to be the course of the fire.
This video is fantastic! Discovering this clever method to fix a broken electrical plug is both practical and insightful-it's a game-changer for quick, DIY repairs!
🙏THE GOSPEL OF THE WORD OF ALMIGHTY GOD "the Salvation of the last day that Christ brought in the second and last incarnation of His new and holy name" (The kingdom walks in the midst of mankind, it is formed in the midst of mankind, it stands in the midst of mankind; no force can destroy My kingdom. When the sign of My new beginning is revealed to the masses, how will humanity react? I now walk in the midst of My people, I dwell in the midst of My people. Now, those who have true love for Me, such a person is blessed; blessed are those who submit to Me, they will surely remain in My kingdom; blessed are those who know Me, they will surely hold power in My kingdom; blessed are those who desirewith Me, they will surely be saved from the chains of Satan and they will enjoy the blessing of Me; blessed are those who can renounce themselves, they will surely enter My possession, and inherit the reward of My kingdom. I will bless those who are satisfied with My words; surely they will be the pillars that will raise the top of My kingdom, surely they will have an incomparable reward in My house, and no one will be like them. Have you accepted the blessings given to you? In the midst of darkness, you will certainly not lose the light that guides you. Surely you will be the master of all beings. Surely you will be victorious before Satan. You will surely be strong and steadfast in the land of Sinim.) Almighty God said The KINGDOM expands in the midst of mankind, it is formed in the midst of mankind, it stands in the midst of mankind; NO FORCE can DESTROY My KINGDOM. Among My people who are in the kingdom of the present, who among you is not a person who mingles with people? Who among you lies outside the human condition? WHEN the SIGN of My NEW BEGINNING is REVEALED to the MASSES, HOW will HUMANITY REACT? You have SEEN with your OWN EYES the STATE of MANKIND; SURELY you NO LONGER HOPE to ENDURE forever in this WORLD? I now WALK in the MIDST of My PEOPLE, I DWELL in the MIDST of My PEOPLE. NOW, THOSE who have TRUE LOVE for Me, such a PERSON is BLESSED; BLESSED are THOSE who SUBMIT to Me, they will SURELY REMAIN in My KINGDOM; BLESSED are those who KNOW Me, they will SURELY HOLD POWER in My KINGDOM; BLESSED are those who DESIREWITH Me, they will SURELY be SAVED from the CHAINS of SATAN and they will ENJOY the BLESSING of Me; BLESSED are those who can RENOUNCE THEMSELVES, they will SURELY ENTER My POSSESSION, and INHERIT the REWARD of My KINGDOM. I will REMEMBER those who WORK for My SAKE, I will EMBRACE with JOY those who SPEND for My SAKE, I will GIVE PLEASURES to those who SACRIFICE to Me. 🙏 I will BLESS those who are SATISFIED with My WORDS; SURELY they will be the PILLARS that will RAISE the TOP of My KINGDOM, SURELY they will have an INCOMPARABLE REWARD in My HOUSE, and NO ONE will be LIKE them.🌷 Have you ACCEPTED the BLESSINGS GIVEN to you? Have you LOOKED for what was PROMISED to you? 🙏 UNDER the GUIDANCE of My LIGHT, you will SURELY BREAK free from the STRANGLEHOLD of the FORCES of DARKNESS. In the MIDST of DARKNESS, you will CERTAINLY NOT LOSE the LIGHT that GUIDES you. SURELY YOU will be the MASTER of ALL BEINGS. SURELY you will be VICTORIOUS before SATAN. 🙏🛑 WHEN the KINGDOM of the GREAT RED DRAGON is BROKEN, YOU will CERTAINLY STAND in the MIDST of a GREAT CROWD to WITNESS My VICTORY. You will SURELY be STRONG and DURABLE in the LAND of SINIM. Through the SUFFERINGS you ENDURE, you will INHERIT the BLESSING that COMES from Me, and My GLORY will SURELY SHINE all WITHIN the UNIVERSE. 🙏💐 From "The Word, Vol. 1. The Manifestation and Work of God. God's Words to the Whole Universe, Chapter 19 Fulfillment of (John 1:1) and (Ezekiel 2:9-10), (Revelation 19:9,13) 📥Calling and leading everyone to His lowered Kingdom or Church because it is still standing on earth in the holy place in the air/ youtube "THE CHURCH OF ALMIGHTY GOD 💐 this is the fulfillment of what He said to Peter 2,000 years ago, recorded in (Matthew 16:18'19). This is the the only Church of each one of our spirit that we must listen to or eat and drink like how we eat, dress and sleep every day so that He can guide us and change us by rejecting the evil attached by satan so as to be perfect, having attained eternal life that will enter the coming replacement of the New Heaven and New Earth. 📥 👉 Note 📧 The coming of the Spirit of God incarnated in His second and last incarnation is the fulfillment of what was prophesied in the great BOOK of REVELATION so the last day or last age has come and His coming is to judge and punish unrighteousness of a person so that the pure or perfect person will be able to enter the approaching New Heaven and New Earth in the final judgment that all souls at that time will be reborn to receive the appropriate corresponding punishment (the one that will be destroyed and will no longer exist ) or the reward of living forever in the New World. 💟
Nie widzę tutaj niczego "bardzo niebezpiecznego". O ile pracę wykona się starannie i solidnie. I tym różni się podejście do spraw technicznych ludzi Zachodu i Polaków, ze u Was wszystko co jest tylko trochę zepsute, wyrzuca się i kupuje nowe, zamiast naprawiać. Niestety ten zły trend dotarł już do naszego kraju. Jesteśmy coraz bardziej zasypywani elektroodpadami! Na szczęście Unia Europejska dostrzegła ten problem. Obowiązują już dyrektywy, które zobowiązują konsumentów do naprawiania uszkodzonych sprzętów, a nie ich wyrzucania. Naprawiania fachowego - podkreślam, a nie partactwa, które faktycznie może być przyczyną wypadków. Wiem co piszę. Z zawodu jestem elektronikiem i automatykiem.
Lo que me sorprende es que no se haya rebanado un dedo con el cutter !!!! Termocontraibles, soldadura, hilo, la gótica, cinta aisladora. Ahhh, pero me evito ponerle una ficha nueva😂😂😂😂😂🤦♂️🤦♂️🤦♂️🤦♂️🤦♂️
Achei muito válido,uma pena que comentaram de forma negativa.As vezes estamos em situações que não podemos sair pra comprar um plug novo, ou nao temos tempo pra sair ,então com um pouco de paciencia da pra se safar até um reparo mais adequado com peças novas. Direto do Brazil ,abraços 🇧🇷🇧🇷🇧🇷🇧🇷🇧🇷🇧🇷🇧🇷🇧🇷🇧🇷🇧🇷🇧🇷🇧🇷🇧🇷🇧🇷🇧🇷🇧🇷🇧🇷🇧🇷🇧🇷🇧🇷🇧🇷
That's DANGEROUS what he's doing. It can lead to a fire, because the wires he first coats with solder and then solders together. This results in high voltages and or too much heat. !!!
🙏THE GOSPEL OF THE WORD OF ALMIGHTY GOD "the Salvation of the last day that Christ brought in the second and last incarnation of His new and holy name" (The kingdom walks in the midst of mankind, it is formed in the midst of mankind, it stands in the midst of mankind; no force can destroy My kingdom. When the sign of My new beginning is revealed to the masses, how will humanity react? I now walk in the midst of My people, I dwell in the midst of My people. Now, those who have true love for Me, such a person is blessed; blessed are those who submit to Me, they will surely remain in My kingdom; blessed are those who know Me, they will surely hold power in My kingdom; blessed are those who desirewith Me, they will surely be saved from the chains of Satan and they will enjoy the blessing of Me; blessed are those who can renounce themselves, they will surely enter My possession, and inherit the reward of My kingdom. I will bless those who are satisfied with My words; surely they will be the pillars that will raise the top of My kingdom, surely they will have an incomparable reward in My house, and no one will be like them. Have you accepted the blessings given to you? In the midst of darkness, you will certainly not lose the light that guides you. Surely you will be the master of all beings. Surely you will be victorious before Satan. You will surely be strong and steadfast in the land of Sinim.) Almighty God said The KINGDOM expands in the midst of mankind, it is formed in the midst of mankind, it stands in the midst of mankind; NO FORCE can DESTROY My KINGDOM. Among My people who are in the kingdom of the present, who among you is not a person who mingles with people? Who among you lies outside the human condition? WHEN the SIGN of My NEW BEGINNING is REVEALED to the MASSES, HOW will HUMANITY REACT? You have SEEN with your OWN EYES the STATE of MANKIND; SURELY you NO LONGER HOPE to ENDURE forever in this WORLD? I now WALK in the MIDST of My PEOPLE, I DWELL in the MIDST of My PEOPLE. NOW, THOSE who have TRUE LOVE for Me, such a PERSON is BLESSED; BLESSED are THOSE who SUBMIT to Me, they will SURELY REMAIN in My KINGDOM; BLESSED are those who KNOW Me, they will SURELY HOLD POWER in My KINGDOM; BLESSED are those who DESIREWITH Me, they will SURELY be SAVED from the CHAINS of SATAN and they will ENJOY the BLESSING of Me; BLESSED are those who can RENOUNCE THEMSELVES, they will SURELY ENTER My POSSESSION, and INHERIT the REWARD of My KINGDOM. I will REMEMBER those who WORK for My SAKE, I will EMBRACE with JOY those who SPEND for My SAKE, I will GIVE PLEASURES to those who SACRIFICE to Me. 🙏 I will BLESS those who are SATISFIED with My WORDS; SURELY they will be the PILLARS that will RAISE the TOP of My KINGDOM, SURELY they will have an INCOMPARABLE REWARD in My HOUSE, and NO ONE will be LIKE them.🌷 Have you ACCEPTED the BLESSINGS GIVEN to you? Have you LOOKED for what was PROMISED to you? 🙏 UNDER the GUIDANCE of My LIGHT, you will SURELY BREAK free from the STRANGLEHOLD of the FORCES of DARKNESS. In the MIDST of DARKNESS, you will CERTAINLY NOT LOSE the LIGHT that GUIDES you. SURELY YOU will be the MASTER of ALL BEINGS. SURELY you will be VICTORIOUS before SATAN. 🙏🛑 WHEN the KINGDOM of the GREAT RED DRAGON is BROKEN, YOU will CERTAINLY STAND in the MIDST of a GREAT CROWD to WITNESS My VICTORY. You will SURELY be STRONG and DURABLE in the LAND of SINIM. Through the SUFFERINGS you ENDURE, you will INHERIT the BLESSING that COMES from Me, and My GLORY will SURELY SHINE all WITHIN the UNIVERSE. 🙏💐 From "The Word, Vol. 1. The Manifestation and Work of God. God's Words to the Whole Universe, Chapter 19 Fulfillment of (John 1:1) and (Ezekiel 2:9-10), (Revelation 19:9,13) 📥Calling and leading everyone to His lowered Kingdom or Church because it is still standing on earth in the holy place in the air/ youtube "THE CHURCH OF ALMIGHTY GOD 💐 this is the fulfillment of what He said to Peter 2,000 years ago, recorded in (Matthew 16:18'19). This is the the only Church of each one of our spirit that we must listen to or eat and drink like how we eat, dress and sleep every day so that He can guide us and change us by rejecting the evil attached by satan so as to be perfect, having attained eternal life that will enter the coming replacement of the New Heaven and New Earth. 📥 👉 Note 📧 The coming of the Spirit of God incarnated in His second and last incarnation is the fulfillment of what was prophesied in the great BOOK of REVELATION so the last day or last age has come and His coming is to judge and punish unrighteousness of a person so that the pure or perfect person will be able to enter the approaching New Heaven and New Earth in the final judgment that all souls at that time will be reborn to receive the appropriate corresponding punishment (the one that will be destroyed and will no longer exist ) or the reward of living forever in the New World. 💟
Really? Are you really serious? You can buy a cable like this for little money. This has been tested and it is also safer for your fingers if I see how you work with the cutter knife
acheter une prise serait tout aussi judicieux , non ? sans compter la prise de risque en découpant avec le cutter en direction des doigts ! on sent bien l( hyper bricoleur futur candidat pour les urgences !
I make repairs like this frequently. Though I use an air tool instead of a lighter for my shrink tube and I Use a third piece of shrink tube over the whole repair. I flux the wires as well to make tinning easier and more reliable. Never had a problem with a repair. I dont use thread as I dont see a benefit to it and that looks time consuming. A properly soldered joint can not be pulled apart and once wrapped by a properly rated material like tube or tape is an accepted standard of repair worldwide. IF I were going to make that repair and I had the option I would have bought and installed a replacement end but this works too.
Interesting to read your comments among all the other "unsafe" tosh! I'd add that I would use a larger bore shrink wrap for the final covering rather than cotton thread.
Looks great but one thing I missed. Is how many times you need to twirl the plug the solder and the wire as you prepare to carry out this procedure and what music to play as you go about this great procedure
Nunca hubiera creído que se pudiera hacer tal truco de ingeniería espacial, de seguro el que realizó el video trabaja para una empresa de alta tecnología y es el jefe de investigación avanzada.
Fajne jest to, że autor promuje ideę naprawiania sprzętów domowych, a nie wyrzucania ich z powodu byle głupstwa i zaśmiecania Ziemi. Za to daję kciuka w górę! Mam jednak dwie małe uwagi. Po pierwsze dość słabo wygląda ta pomarszczona czarna taśma izolacyjna, która w dodatku podczas dłuższego użytkowania tak naprawionej wtyczki będzie się rozklejała brudząc ręce i przewód klejem. Obwinięcie przewodów dratwą też nie jest dobrym rozwiązaniem. Zauważcie, że najczęściej przewody od wtyczek zalewanych odrywają sie w miejscu, gdzie kończy się tzw. odgiętka. Czyli tam, gdzie przewód wychodzi z nieco elastycznego plastiku wtyczki. Wtyczka naprawiona w sposób zaprezentowany nam na nagraniu zagrożona jest ponownym oberwaniem się przewodów przy twardym plastiku. I co wówczas możemy zrobić? Nic, już tylko wyrzucić wtyczkę. Proponuję jeszcze przed zlutowaniem urwanych przewodów nałożyć na przewód grubościenną koszulkę termokurczliwą z klejem. Jej średnica musi być taka, by częściowo udało się ją naciągnąć na wąską część wtyczki. Po zlutowaniu przewodów i zabezpieczeniu miejsca połączenia koszulkami termokurczliwymi jak na nagraniu proponuję zamiast nawijania dratwy wzmacnianej klejem Super Glue, nawinięcie gęsto drutu miedzianego w izolacji np. fi 2 mm. Powstałą sprężynkę rozpoczynamy nawijać 2-3 cm od wtyczki, a kończymy już na niej. Ostatnie zwoje drutu po ściśnięciu na wtyczce w imadle należy ze sobą zlutować. Całość chowamy pod wspomnianą wcześniej grubościenną termokurczliwą koszulką. (Tych, którzy podejrzewają, że w sprężynce może się indukowac prąd od razu uspokoję - nic takiego nie będzie miało miejsca w przypadku używania przewodu do zasilania napięciem 230 V AC - tu pole elektromagnetyczne obu przewodów zasilających wzajemnie się znosi i nie oddziałuje na zwoje drutu, jakie sugeruję wykonać.) Gdy teraz nawet znów oderwie się nam przewód za awaryjną odgiętką z miedzianej sprężynki, to naprawę będzie można powtórzyć, gdyż wciąż będziemy mogli dolutować przewody do końców przewodów wychodzących z wtyczki. Nie byłoby to możliwe w propozycji pokazanej na video. No i na koniec - koszulki termokurczliwe należy raczej obkurczać gorącym powietrzem, a nie płomieniem zapalniczki, zaś izolację z przewodów zdejmować specjalnymi cążkami, a nie obtapiać. Pozdrawiam serdecznie Kreatywnego Mistrza!
Cutting towards your friend is definitely not the best advice here 🙅♂️ Always prioritize safety first and follow the proper techniques when fixing electrical plugs! ⚡
Large heat shink can be used to hold a severed finger tip in place until the nerve ends re-connect. Use soldering iron to heat the wrap. Use a sharp knife to remove wrap afterwards.
If you MUST carry out this dangerous repair, at least offset the two joins so that they are not alongside one another and cannot short across. Secondly, don't do this.
Offsetting the joins is a great tip to prevent short circuits! Make sure to follow safety precautions when attempting any electrical repairs 🔌🔧.
Makes no difference because there is insulation between the soldered joins.
And If you are alone, in a valley, in a desert 100km far?!
And double, triple the heatshrink tubing, and use bigger ones to cover everything instead of using cotton and tape.
Filling larger heatshrink tube with hot glue can be used to help with strain relief too.
This video should be removed. It could cause someone's death. This is very dangerous. A replacement plug top is the only safe solution.
When I was a kid, my father used to put wires straight into the power outlet if there was no plug. Old cables with thick copper veins and 230V going through them. I felt uncomfortable seeing it, yet after many years I do believe it was a safer thing than what you did here, lol. The worst thing about it is the fact it gives you a sense of safety.
I am glad you found a solution that worked for you, but it's always best to use proper safety measures when dealing with electricity! Stay safe out there! ⚡️
Don't do this! Better to buy a new one!
Won't that cost more money?
Das ist Pfusch 1a !. Und gefährlich.
Yes, we will wasting our time and it is not safe 😂
Thank you Master !!!
Yeah good advice they are real cheap to buy
Temporary fixes can become permanent- then accidents happen- tragically!
Always remember to follow proper safety procedures when fixing electrical plugs to prevent accidents! ⚡🔌
On his next video, how to fix an amputated thumb.
I'll keep that in mind for my next video! 🔧👍
🤣🤣🤣🤣
Learning CPR
Let's hope there are no more videos from this idiot
lol lol lol i was thinkng the same thing lol
It may look safe and probably it even is save, but when you have a fire in the house, the insurance will not pay a penny when this is found in your house. even when it was not the real course of the fire. A replacement is so cheap, you do not want to take the risk.
It neither looks nor is safe. Just keep your fingers away from such “hacks” and buy a safety certified replacement instead.
no, this is bullshit.
Insurance has to pay, if that was not the cause
If the video ended 0:08 it would be absolut fine.
It's great to see your engagement! Thanks for being a part of our community. 🙌
That would have been the correct behaviour. Everything that follows is just dangerous.
This is a highly dangerous bodge job which should not be carried out except in an emergency when buying a new plug or even a complete lead is not possible. A simpler temporary repair is to use a connector block. Ugly but safer
Thank you for the tip! Safety is always a top priority when dealing with electrical repairs 🛠️.
It is an excellent video recording, but the whole point on safety is missing. If someone follows the instructions perfectly, they end up with a very dangerous setup. No, unless this is an emergency requirement, it should never be done. Buy a replacement plug that was designed to work better and last longer. If someone repairs an electrical cord in this fashion, they end up having an electrical failure and possibly a fire hazard.
I said that just before reading your post. Shouldnt be allowed to show this sort of video
Safe the earth. Recycle when you can!! One less cord in the trash.
To say nothing of how one’s Fingers could be badly cut up with that razor knife….
So glad you stopped by to comment! Thanks for the engagement.
@@markswanson6898
Save the Earth, but use your brain first.
The way of "repairing" gives dangerous utility an can cost somebody's life.
It is better to throw the plug to ♻️ and use replacement plug. Really.
So buy a soldering iron, solder, knife, scissors, tape, and spend 45 minutes to repair a $2 plug. Yeah, sure. 😂
And it would probably be badly soldered, had an inadequate safety and it would look ugly...
never ever cut knive to skin! and flame too close to isolation material. it burned!
yeah but 1.9M views but
Uporaba izolirnega traku ni profesionalno. Raje kupi nov kabli z vtičem!
하나사는게 훨씬싸다 미친짖 가이다
Hey kids you can use your playstation now. Tug on the cord like you usually do (how it broke in the first place). Reach around the back of the cabinet to plug it in with your wet hands. I have done this (remote location not near stores) with offset joins and heavy shrink over the top and still didn't trust it so got rid of it. I only watched this to the end to see how bad it really was. I noticed slight nick in the insulation for starters - prone to break/shortcircuit even if not conductive just yet.
We're glad you watched till the end! Remember to always prioritize safety when dealing with electrical plugs. Stay safe! 💡🔌
@@CreativeMaster999 If you reallllllly cared about safety you would take this video down. Sure, make videos showing how to fix things, but when you get 500 comments showing it AINT GOOD, TAKE IT DOWN!!! Make a new one with the offset mentioned, use a real wire stripper that won't nick the insulation, don't wrap it with thread, don't wrap it with rubber tape, and there should be something to replace the grip you cut off.
So many things are wrong in this video, but I'll just say this: Never, ever use a cigarette lighter like he did in this video!
Może to jakiś piroman?😅Pracowałem 51 lat jako elektryk czegoś takiego jeszcze nie widziałem.😮
😊
I agree very dangerous, I suffered a very bad electric shock and burns from a similar type of repair many years ago 😮
I'm sorry to hear about your experience. Safety is always the top priority when dealing with electrical repairs 🔌.
@@CreativeMaster999 Are you for real, talking about safety, when you are carrying out a very dangerous repair like this. You should be ashamed of yourself for being so stupid.
Bir tane elektrik fişi alıp bağlasaydın daha zahmetsiz olurdu
Or just spend $1.50 on a new plug.
Sometimes a quick fix is all you need 😉🔌.
I never had any luck with off the shelf plug ends. Even when I paid $200 to get a bunch of my cords fixed. I do a similar method as this with more reinforcement than the video shows. Nothing you buy off the shelf is engineered to work flawlessly. Everything is engineered to be just good enough to sell at the price people are willing to pay. Moreover, even the plug ends they sell that do not really work, are often as expensive as getting a new cord.
I use several extension cords for work each day and use about 250 feet of them on the weekends to mow my 75 feet by 400 feet deep lawn, since I have so many cords, and a corded lawn mower doesn't stall on long grass like my riding and push gas mowers, and the electric cuts the lawn shorter and the lawn looks better. My lawn grows an inch per day and I need to cut it 2 times a week with my gas mowers and once with the electric.
Also, the thinker the copper wire, the more brittle and more quickly we get cord breaks. The thick wire is nearly impossible to get a good plug replacement. So slicing and soldering has been the only practical solution. It seems like a good thick cord does not take very long before needing a repair, more so than the thin.
The wife and son refuse to mow rationally, from the outlet outwards, so the cord cannot get run over. I think they also purposely run over the cord with the lawn mower as an excuse not to mow, just as they use the excuse that they can't get the fas mowers started. Thus a seemingly constant cord repair is the norm.
@@CreativeMaster999 "quick" is a big word here but can you tell us the cost of therepair ? soldering iron consumption + Solder Wire, lighter, heat-shrinkable sleeves, tape and unvaluable time. Of course i suppose you already have all necessary tools
@@CreativeMaster999 Followed by a funeral.
Not good! Too many chances of nicks in the wire and short circuits. Far easier and safer to buy a new plug and connect the appliance end of the cord to it.
I completely understand your concern, but this method can be a quick fix in emergencies! Just make sure to handle the wires carefully 🔌.
Por favor que nadie haga este remedio, mejor comprar un enchufe desmontable, bien colocado es mucho más seguro y es económico.
Wonder how long it would survive if that lead is on a vacuum-cleaner fitted with a retractable-cord?
How to win the Darwin Award.
What a hack job, not to mention dangerous!
This would do for an emergency fix but never a permanent repair. Just get a bew plug for a few pence/cents
So glad you stopped by to comment! Thanks for the engagement.
A new plug would be best, but he used a standard solder splice. I would suggest that he also use shrink wrap tape over the electrical tape to make for a stronger safer splice.
Глупости
Nothing wrong with this fix maybe just pet a new plug on it but it's fine I'm 60 🇬🇧🇮🇪
The "repair" is against all safety standards - acceptable only in the absolute case of need and far away from children.
The method shown in the video should only be used in extreme cases and away from children. Remember to always prioritize safety when dealing with electrical repairs! ⚠️🔌
@@CreativeMaster999 And as most idiots won't understand that nor read the comment, the video should be pulled.
Super comentariu,asa este
stop bothering us with your stupid standards..., nature works like that
Wszelkie naprawy powinno się przeprowadzać z dala od ( małych) dzieci. A więc jako, że to oczywista oczywistość druga część komentarza zupełnie zbędna
I've done stuff like that many times... but only on low-voltage systems like battery powered kids toys or led light chains. Even then I cut the cables to different length so the soldered cables would not touch each other even if insulation would fail.
Never ever I would try this on a power cable!!! I like the place I live a lot, I don't wanna burn it...
That's a smart approach for safety! Always better to be cautious with electrical work. Stay safe! 🔌🔧
Looks good to me
Funny thing... "Low Voltage" DC toys can catch on fire easier than single phase given a bad connection.
I've seen a house alarm wired with single core wire across a ceiling space... the insulation had melted of nearly it's entire length.
You are working totally unsafe. By cutting towards the finger you are setting a bad and dangerous example. Instead of heating the heat shrink tubing, you have blackened it with flame, soot has settled, i.e. carbon, which in combination with the adhesive of the insulating tape creates a conductor of electricity - this is a direct path to fire. The original plug has an element that makes it easier to remove from the socket without pulling the cable, you cut it out and did not recreate it. You should be banned from publishing nonsense for the safety of people and equipment.
An otherstupid telling how to do things when probably has no idear of nothing....ha you forget ...the helmet ,the security shoes...bla bla bla
Very dangerous game. UTube must stop such posts.
Thanks for the comment
P
My old woodwork teacher always used to repeat the mantra, ‘Hands behind the cutting edge.’ So much so that my wife repeats it to me now, as I was always saying it out loud. 🤣
Other title to this video: "Only maniacs use this method to fix a broken cable."
Haha, maybe a bit unconventional but it gets the job done! 😉🔌.
このやり方はお勧めできません。
DIYが好きな方はある程度可能かもしれませんが火災がおきて家を失うかもしれません。
わずかな費用を節約できても元も子もないと認識するべきです。
修理屋さんや電気工事士の資格のある人に依頼しましょう。
火災保険が減額されるかもね。
متأسفانه قیمت دوشاخهها متفاوت است اما در این ویدیو نشان میدهیم چگونه یک دوشاخه شکسته را تعمیر کنید! 💡🔌
この動画の作成者さんは日本人ではないのでしょう。
日本では36Vを超えるような電気回路を工事する場合には国家資格が必要になります。
素人が工事をして事故を起こすリスクを減らすためです。
まぁ作成者さんも、世界中に発信する動画で、いちいち各国の事情を調べたりはしないでしょう。
火災の発生以前にカッター刃で指を切創しそうで怖い
@@CreativeMaster999
ほぼ予想通りの修理方法。
だが耐久性に問題ありと見た。
You're running 230v through that? I think I'd just install a new plug. Rock on.
I don't think its 230 Matt. I think that is a European plug. Either way it is way too much effort for the benefit. A new plug is the way to go.
I heard you, thanks for the comment
@@CITADEL5 And what do you think the standard is in Europe?
@@krisja2995 I thought it was 115. Don't assume I know I am just guessing.
@@CITADEL5 Standard (for Belgium/ Europe) is 220V + and - 10%
I recently cut my hedge trimmer mains led, with the trimmer!
I bought an external in line mains connector, cut out the damaged cable section and fitted the connector in its place. Just make sure that the prong side is on the appliance side.
Dave UK.
Great job on fixing your hedge trimmer mains lead! It's always handy to know how to repair electrical plugs 💡🔌.
Get an electrician to fix this PROPERLY!
Using the *worst* possible tip on the soldering iron was truly the cherry on top.
Haha, glad you enjoyed the tip! 🍒 Thank you for watching!
....& some of the worst soldering I've seen for years!
Don't do it like this . Its dangerous. Not to mention the injury risk while carrying out the repair !!!
I appreciate your concern for safety! In the video, I demonstrate a safe and effective way to fix a broken electrical plug. Always prioritize safety first when attempting any repairs. 🔌👍
...is he the son of Ted Bundy ?
The injury risk is a skill issue, I have used similar techniques without problems (but never so electrically unsafe).
Materialkosten inkl. Arbeitszeit: ca. 5 Euro, Neukauf Kabel ca. 3 Euro ... Und ja: Notruf Feuerwehr 112 !
Danke für den Tipp! 👍🔌.
You can feel the silent screams of pain of every electrician as you watch this
You just saved electricians everywhere from a heart attack with this tip! 💡🔌
Melhor comprar um plug novo e não arriscar a segurança
Melhor seguir as dicas do vídeo e consertar o plug de forma segura! 💡🔌
@@CreativeMaster999 Você achou essa forma segura? E ainda se intitula mestre? Me desculpa, mas todo essa trabalho com solda é queimando e fio. É 5 reais um plug novo meu amigo. Essa borracha de proteção de fábrica é testada para isolar o calor da amperagem elétrica. Isso é uma GAMBIARRA e muito trabalhosa.
@@ORealdavidavc está redondamente CERTO
😂😂😂
PARABÉNS
Vídeo longo pra uma gambiarra
Compro um novo
É melhor é mais seguro
Põe um plug novo é baratinho
Pô
Francamente 😅
Replacing a plug was one of the requirements for advancing a rank when I was a Cub Scout. 60 years ago. Of course, it was a much more important life skill back then…
That's awesome! Learning how to replace a plug is definitely a valuable life skill that never goes out of style 💡🔌.
the best advert i have seen for the UK plug.
Glad you found the video helpful! 🇬🇧🔌.
You are working totally unsafe, showing wrong practice
I always prioritize safety first in all my videos! Make sure to follow proper safety precautions when attempting any DIY repairs. Stay safe! 👷♂️⚡.
@@CreativeMaster999what a load of rubbish. Totally unsafe practice procedure. You should be banned from posting stuff like this
Why bother! Buy a new plug!!!!
Why bother fixing when you can buy new? Because it's a quick and cost-effective solution! 🔌💡
@@CreativeMaster999no es rápida, tardas unos 10 minutos y es más seguro poner un enchufe nuevo...
May by you can be at work and you can't find quikly a shop for buying a new one 🤪
Firele puteau fi taiate mai scurte astfel incat reparatia sa fie mai stransa , mai mica , mai redusa . . .
@@CreativeMaster999перевести на русский
This guy deserves to be employed in NASA. What an unknown scientist!?
Ahahaha!
Thanks for the comment
My grampa would be so proud of you. We used to fix everything, whereas now we usually just buy a new one. Grampa is rolling in his grave... but in the factory they stamp out a new cord in exactly 2.5 seconds, and this took 5 minutes to repair, not counting 3 hours for trips to the electronics store for soldering iron, solder, and shrink-wrap; to the hardware store for electrical tape; the fabric store for thread; the department store for superglue... It really doesn't make sense to fix a lot of broken junk unless you're stuck in some remote location and need that lamp in a hurry. And have all that stuff on hand.
Your grampa's spirit lives on in those who still choose to repair instead of replace! It's a lost art, but so satisfying when you get it right 🔧🔌.
2:57 cold solder joint. Not good at all. At least use some flux and not brush the solder over the wires. Afterwards, throw it all away and buy a new cord/appliance. I would not recommend anyone using this method.
I appreciate your feedback. It's always important to use proper techniques when fixing electrical plugs. Thank you! 👍
Dangerous
Be careful and follow the instructions in the video to safely fix the broken electrical plug! ⚠️.
😂Non fatelo
Rename:
How to burn down your home in 5 minutes or less!!!
No worries, this video is actually about fixing electrical plugs, not burning down homes! 🔌🏡.
...in a good barbecue ?
@@CreativeMaster999 Yeah, but the last will be the result of the first and the biggest problem is that the insurance will not pay a penny when this was found to be the course of the fire.
@@toppersvantoen Even if it wasn't, it being there (and found) is usually enough.
How to win a Darwin Award.
Otw di coba nih makasih salam dari Indonesia 🇮🇩
Salamat atas dukungannya! Semoga tips dalam video saya bermanfaat untuk Anda 🇮🇩🔌.
This video is fantastic! Discovering this clever method to fix a broken electrical plug is both practical and insightful-it's a game-changer for quick, DIY repairs!
Thank you so much for your kind words! I'm glad you found the method helpful for your DIY repairs 🛠️.
Шнобелевская премия 100% !
Crazy!
That's right! 😄 Check out the video for the full tutorial on fixing a broken electrical plug! 💡🔌.
Dont try this at home ✋. In Germany we call it Murks 🙈
I hope you enjoyed the video! Remember, safety first when dealing with electrical repairs 💡🔌.
@@CreativeMaster999Silly sod ...
Gefährlicher Leichtsinn.
Abisolieren mit nem BIC....sagt alles...
Bravo 👏
Thank you! I'm glad you found the tip helpful 👍.
Oje, das Video straft jeden ausgebildeten Elektriker dabei? Wer weiss warum bitte?
Keine Sorge! Mit diesem Trick kann jeder ein kaputtes Stecker reparieren 💡🔧.
@@CreativeMaster999 I'M SORRY BUT YOU'RE OUT OF YOUR FRIGGIN MIND!
Er hätte besser Wago-Klemmen benutzt ? 🤔 😂
@@CreativeMaster999
Brandgefährlicher Murks! Ersatzkabel gibt es für ein Taschengeld.
Geht max. bis zur nächsten DGUV V3 Prüfung 😂
Not profitable at all
Sorry to hear that you didn't find it profitable! Hopefully, you can still find the video helpful in fixing your electrical plug. 💡🔌
DON'T MIND HIM. HE'S A PLUMBER.@@CreativeMaster999
@@CreativeMaster999 Hopefully, you can find a video using a butt- plug.
A opłacalne jest wyrzucanie takiej wtyczki i kabla z punktu widzenia zaśmiecania planety? To jest dopiero szczyt nieopłacalności!
Plums, you're doin a fine job regardless of the negative comments!!!
🙏THE GOSPEL OF THE WORD OF ALMIGHTY GOD "the Salvation of the last day that Christ brought in the second and last incarnation of His new and holy name"
(The kingdom walks in the midst of mankind, it is formed in the midst of mankind, it stands in the midst of mankind; no force can destroy My kingdom. When the sign of My new beginning is revealed to the masses, how will humanity react? I now walk in the midst of My people, I dwell in the midst of My people. Now, those who have true love for Me, such a person is blessed; blessed are those who submit to Me, they will surely remain in My kingdom; blessed are those who know Me, they will surely hold power in My kingdom; blessed are those who desirewith Me, they will surely be saved from the chains of Satan and they will enjoy the blessing of Me; blessed are those who can renounce themselves, they will surely enter My possession, and inherit the reward of My kingdom. I will bless those who are satisfied with My words; surely they will be the pillars that will raise the top of My kingdom, surely they will have an incomparable reward in My house, and no one will be like them. Have you accepted the blessings given to you? In the midst of darkness, you will certainly not lose the light that guides you. Surely you will be the master of all beings. Surely you will be victorious before Satan. You will surely be strong and steadfast in the land of Sinim.)
Almighty God said
The KINGDOM expands in the midst of mankind, it is formed in the midst of mankind, it stands in the midst of mankind; NO FORCE can DESTROY My KINGDOM. Among My people who are in the kingdom of the present, who among you is not a person who mingles with people? Who among you lies outside the human condition? WHEN the SIGN of My NEW BEGINNING is REVEALED to the MASSES, HOW will HUMANITY REACT? You have SEEN with your OWN EYES the STATE of MANKIND; SURELY you NO LONGER HOPE to ENDURE forever in this WORLD? I now WALK in the MIDST of My PEOPLE, I DWELL in the MIDST of My PEOPLE. NOW, THOSE who have TRUE LOVE for Me, such a PERSON is BLESSED; BLESSED are THOSE who SUBMIT to Me, they will SURELY REMAIN in My KINGDOM; BLESSED are those who KNOW Me, they will SURELY HOLD POWER in My KINGDOM; BLESSED are those who DESIREWITH Me, they will SURELY be SAVED from the CHAINS of SATAN and they will ENJOY the BLESSING of Me; BLESSED are those who can RENOUNCE THEMSELVES, they will SURELY ENTER My POSSESSION, and INHERIT the REWARD of My KINGDOM. I will REMEMBER those who WORK for My SAKE, I will EMBRACE with JOY those who SPEND for My SAKE, I will GIVE PLEASURES to those who SACRIFICE to Me. 🙏
I will BLESS those who are SATISFIED with My WORDS; SURELY they will be the PILLARS that will RAISE the TOP of My KINGDOM, SURELY they will have an INCOMPARABLE REWARD in My HOUSE, and NO ONE will be LIKE them.🌷
Have you ACCEPTED the BLESSINGS GIVEN to you? Have you LOOKED for what was PROMISED to you? 🙏
UNDER the GUIDANCE of My LIGHT, you will SURELY BREAK free from the STRANGLEHOLD of the FORCES of DARKNESS. In the MIDST of DARKNESS, you will CERTAINLY NOT LOSE the LIGHT that GUIDES you. SURELY YOU will be the MASTER of ALL BEINGS. SURELY you will be VICTORIOUS before SATAN. 🙏🛑
WHEN the KINGDOM of the GREAT RED DRAGON is BROKEN, YOU will CERTAINLY STAND in the MIDST of a GREAT CROWD to WITNESS My VICTORY. You will SURELY be STRONG and DURABLE in the LAND of SINIM. Through the SUFFERINGS you ENDURE, you will INHERIT the BLESSING that COMES from Me, and My GLORY will SURELY SHINE all WITHIN the UNIVERSE. 🙏💐
From "The Word, Vol. 1. The Manifestation and Work of God. God's Words to the Whole Universe, Chapter 19
Fulfillment of (John 1:1) and (Ezekiel 2:9-10), (Revelation 19:9,13)
📥Calling and leading everyone to His lowered Kingdom or Church because it is still standing on earth in the holy place in the air/ youtube "THE CHURCH OF ALMIGHTY GOD 💐 this is the fulfillment of what He said to Peter 2,000 years ago, recorded in (Matthew 16:18'19).
This is the the only Church of each one of our spirit that we must listen to or eat and drink like how we eat, dress and sleep every day so that He can guide us and change us by rejecting the evil attached by satan so as to be perfect,
having attained eternal life that will enter the coming replacement of the New Heaven and New Earth. 📥
👉 Note 📧
The coming of the Spirit of God incarnated in His second and last incarnation is the fulfillment of what was prophesied in the great BOOK of REVELATION so the last day or last age has come and His coming is to judge and punish unrighteousness of a person so that the pure or perfect person will be able to enter the approaching New Heaven and New Earth in the final judgment that all souls at that time will be reborn to receive the appropriate corresponding punishment (the one that will be destroyed and will no longer exist ) or the reward of living forever in the New World. 💟
Replacement wire with plug: $ 3.50
This done by me: 20 minutes work: $ 20
Material used: $ 2
You saved -$ 18.50
You are a DIY master! 💪🔌 Save money and learn a new skill at the same time. 😉
Very dangerous. Don't do this but buy a new one.
Better to be safe than sorry! Consider buying a new one for your safety 🔌👍.
Nie widzę tutaj niczego "bardzo niebezpiecznego". O ile pracę wykona się starannie i solidnie. I tym różni się podejście do spraw technicznych ludzi Zachodu i Polaków, ze u Was wszystko co jest tylko trochę zepsute, wyrzuca się i kupuje nowe, zamiast naprawiać. Niestety ten zły trend dotarł już do naszego kraju. Jesteśmy coraz bardziej zasypywani elektroodpadami!
Na szczęście Unia Europejska dostrzegła ten problem. Obowiązują już dyrektywy, które zobowiązują konsumentów do naprawiania uszkodzonych sprzętów, a nie ich wyrzucania. Naprawiania fachowego - podkreślam, a nie partactwa, które faktycznie może być przyczyną wypadków.
Wiem co piszę. Z zawodu jestem elektronikiem i automatykiem.
What if the cord of an appliance say, an iron box can not be removed but only the plug got damaged or cut off ?
Es una auténtica barbaridad, es mucho más fácil cambiar ese enchufe macho por una nuevo, para mi es una chapuza peligrosa. Un saludo
Lo que me sorprende es que no se haya rebanado un dedo con el cutter !!!! Termocontraibles, soldadura, hilo, la gótica, cinta aisladora. Ahhh, pero me evito ponerle una ficha nueva😂😂😂😂😂🤦♂️🤦♂️🤦♂️🤦♂️🤦♂️
Cheaper to go and buy one not worth all that effort
It's definitely easier to buy a new one, but this trick can save you time and money in a pinch! 😉🔌.
Achei muito válido,uma pena que comentaram de forma negativa.As vezes estamos em situações que não podemos sair pra comprar um plug novo, ou nao temos tempo pra sair ,então com um pouco de paciencia da pra se safar até um reparo mais adequado com peças novas.
Direto do Brazil ,abraços 🇧🇷🇧🇷🇧🇷🇧🇷🇧🇷🇧🇷🇧🇷🇧🇷🇧🇷🇧🇷🇧🇷🇧🇷🇧🇷🇧🇷🇧🇷🇧🇷🇧🇷🇧🇷🇧🇷🇧🇷🇧🇷
I'm glad you found the tip helpful! With a little patience and creativity, it's possible to make temporary repairs when needed. 🛠👍
Mach keinen Mist,kauf einen neuen Stecker 😢
Kaufe einen neuen Stecker! 💡
Two words - HARDWARE STORE.
Hardware store is definitely a great place to find solutions for electrical plug issues! 🔌🔧
That's DANGEROUS what he's doing. It can lead to a fire, because the wires he first coats with solder and then solders together. This results in high voltages and or too much heat. !!!
This method is not recommended. It's safer to replace the plug entirely to avoid any potential risks. 🔌🔥.
I like the way you show us to repair a broken connection. There is always someone to critic to make negative comment. Really boring.
I appreciate your support and understanding of the repair process! Let's focus on the positive outcomes 🛠️👍.
This is hazard, not safe, you can burn the house down!
It's important to follow safety precautions when fixing electrical plugs, make sure to proceed with caution 🔌🔥.
Dangerous, why bother? New one is cheap and safe
Fixing an electrical plug can save money and reduce waste ♻️. It's a handy skill to have!
🙏THE GOSPEL OF THE WORD OF ALMIGHTY GOD "the Salvation of the last day that Christ brought in the second and last incarnation of His new and holy name"
(The kingdom walks in the midst of mankind, it is formed in the midst of mankind, it stands in the midst of mankind; no force can destroy My kingdom. When the sign of My new beginning is revealed to the masses, how will humanity react? I now walk in the midst of My people, I dwell in the midst of My people. Now, those who have true love for Me, such a person is blessed; blessed are those who submit to Me, they will surely remain in My kingdom; blessed are those who know Me, they will surely hold power in My kingdom; blessed are those who desirewith Me, they will surely be saved from the chains of Satan and they will enjoy the blessing of Me; blessed are those who can renounce themselves, they will surely enter My possession, and inherit the reward of My kingdom. I will bless those who are satisfied with My words; surely they will be the pillars that will raise the top of My kingdom, surely they will have an incomparable reward in My house, and no one will be like them. Have you accepted the blessings given to you? In the midst of darkness, you will certainly not lose the light that guides you. Surely you will be the master of all beings. Surely you will be victorious before Satan. You will surely be strong and steadfast in the land of Sinim.)
Almighty God said
The KINGDOM expands in the midst of mankind, it is formed in the midst of mankind, it stands in the midst of mankind; NO FORCE can DESTROY My KINGDOM. Among My people who are in the kingdom of the present, who among you is not a person who mingles with people? Who among you lies outside the human condition? WHEN the SIGN of My NEW BEGINNING is REVEALED to the MASSES, HOW will HUMANITY REACT? You have SEEN with your OWN EYES the STATE of MANKIND; SURELY you NO LONGER HOPE to ENDURE forever in this WORLD? I now WALK in the MIDST of My PEOPLE, I DWELL in the MIDST of My PEOPLE. NOW, THOSE who have TRUE LOVE for Me, such a PERSON is BLESSED; BLESSED are THOSE who SUBMIT to Me, they will SURELY REMAIN in My KINGDOM; BLESSED are those who KNOW Me, they will SURELY HOLD POWER in My KINGDOM; BLESSED are those who DESIREWITH Me, they will SURELY be SAVED from the CHAINS of SATAN and they will ENJOY the BLESSING of Me; BLESSED are those who can RENOUNCE THEMSELVES, they will SURELY ENTER My POSSESSION, and INHERIT the REWARD of My KINGDOM. I will REMEMBER those who WORK for My SAKE, I will EMBRACE with JOY those who SPEND for My SAKE, I will GIVE PLEASURES to those who SACRIFICE to Me. 🙏
I will BLESS those who are SATISFIED with My WORDS; SURELY they will be the PILLARS that will RAISE the TOP of My KINGDOM, SURELY they will have an INCOMPARABLE REWARD in My HOUSE, and NO ONE will be LIKE them.🌷
Have you ACCEPTED the BLESSINGS GIVEN to you? Have you LOOKED for what was PROMISED to you? 🙏
UNDER the GUIDANCE of My LIGHT, you will SURELY BREAK free from the STRANGLEHOLD of the FORCES of DARKNESS. In the MIDST of DARKNESS, you will CERTAINLY NOT LOSE the LIGHT that GUIDES you. SURELY YOU will be the MASTER of ALL BEINGS. SURELY you will be VICTORIOUS before SATAN. 🙏🛑
WHEN the KINGDOM of the GREAT RED DRAGON is BROKEN, YOU will CERTAINLY STAND in the MIDST of a GREAT CROWD to WITNESS My VICTORY. You will SURELY be STRONG and DURABLE in the LAND of SINIM. Through the SUFFERINGS you ENDURE, you will INHERIT the BLESSING that COMES from Me, and My GLORY will SURELY SHINE all WITHIN the UNIVERSE. 🙏💐
From "The Word, Vol. 1. The Manifestation and Work of God. God's Words to the Whole Universe, Chapter 19
Fulfillment of (John 1:1) and (Ezekiel 2:9-10), (Revelation 19:9,13)
📥Calling and leading everyone to His lowered Kingdom or Church because it is still standing on earth in the holy place in the air/ youtube "THE CHURCH OF ALMIGHTY GOD 💐 this is the fulfillment of what He said to Peter 2,000 years ago, recorded in (Matthew 16:18'19).
This is the the only Church of each one of our spirit that we must listen to or eat and drink like how we eat, dress and sleep every day so that He can guide us and change us by rejecting the evil attached by satan so as to be perfect,
having attained eternal life that will enter the coming replacement of the New Heaven and New Earth. 📥
👉 Note 📧
The coming of the Spirit of God incarnated in His second and last incarnation is the fulfillment of what was prophesied in the great BOOK of REVELATION so the last day or last age has come and His coming is to judge and punish unrighteousness of a person so that the pure or perfect person will be able to enter the approaching New Heaven and New Earth in the final judgment that all souls at that time will be reborn to receive the appropriate corresponding punishment (the one that will be destroyed and will no longer exist ) or the reward of living forever in the New World. 💟
Für solchen Schwachsinn braucht man also ein Video🙈🙈🙈?
Ja, es ist wichtig, kleine Reparaturen selbst durchführen zu können, um Kosten zu sparen und unabhängig zu sein! 💡🔌
@@CreativeMaster999 Das ist gefährlicher Pfusch!!!
@@CreativeMaster999
In diesem Fall:
Schwachsinn !!!
Das ist Russische Technologie, du nix anfassen....😁
@@daswornitier3417
Stimmt für das gezeigte Beispiel auf jeden Fall. Dumm ist nur, daß vieles von der russischen Militärtechnik funktioniert.
When you are hours away from a store and need a life saving fix....do it
When you are in a pinch and need a quick fix, this trick can be a lifesaver! 💡🔌
Really? Are you really serious? You can buy a cable like this for little money. This has been tested and it is also safer for your fingers if I see how you work with the cutter knife
I'm glad you found a safer alternative! Stay tuned for more DIY tips on my channel. 👍
How many people have been killed by a plug repaired this way?
How many people have been killed by a plug repaired this way?... Please rest assured, this method is safe and effective when done correctly! 💡🔌
Just buy a new plug
Just watch the video to learn a cost-effective way to fix a broken electrical plug without buying a new one! 😉
Can u tell me how much money he got with this vedeo?
3.6 M watch😊. And how much coments😊
Where's the fun in that :)
Dad, how did you get nickname Zap?
Son, it involves a video.
It's all in the video! ⚡️🔌
カッターの使い方危ない。
新しいプラグ買ってきて工作した方が良い
新しいプラグを使って安全に修理する方法を試してみてください！🔌
2. Go to ER for stitches in thumb.
Make sure to be careful next time you're fixing an electrical plug! Stay safe! ⚡👍
V good
very good❤❤
Thank you! Glad you found the tip helpful! 🛠️🔌.
I can do this. Good idea, but this type of plug commonly have thin connectors. You can do this but under control and accurately.
First class tip ❤❤❤
Thanks for watching! Glad you found the tip helpful 🛠️.
Ich hätte noch einen Schrumpfschlauch über alles gemacht
Ja genau, das wäre sicherer und wuerde mehr Schutz geben.
Thanks for the comment
指を振るのをやめろ。
Heartfelt thanks for your input! We're always excited to hear from you. 💖
你没钱买剥线钳吗？
没有，但是我有这个聪明的方法修理电插头！💡🔌.
acheter une prise serait tout aussi judicieux , non ? sans compter la prise de risque en découpant avec le cutter en direction des doigts ! on sent bien l( hyper bricoleur futur candidat pour les urgences !
Acheter une prise serait effectivement une option plus sécuritaire! Merci pour votre conseil. 💡
What a godawful faff - thank goodness I I’ve in the UK where we have a miraculous modern invention called a Rewireable Plug!, 3:27
We have a clever trick up our sleeves for fixing broken electrical plugs in a jiffy! 💡🔌
@@CreativeMaster999ml 9 bymi
I make repairs like this frequently. Though I use an air tool instead of a lighter for my shrink tube and I Use a third piece of shrink tube over the whole repair. I flux the wires as well to make tinning easier and more reliable. Never had a problem with a repair. I dont use thread as I dont see a benefit to it and that looks time consuming. A properly soldered joint can not be pulled apart and once wrapped by a properly rated material like tube or tape is an accepted standard of repair worldwide. IF I were going to make that repair and I had the option I would have bought and installed a replacement end but this works too.
Interesting to read your comments among all the other "unsafe" tosh! I'd add that I would use a larger bore shrink wrap for the final covering rather than cotton thread.
Hello, thank you for your comment and for sharing your experience.
Thank you
Glad you found the tip helpful! Happy to help 😊.
💨 Thank y💓u.
Thank you! I'm glad you found the tip helpful 🛠️.
Nice job
Thank you! I'm glad you liked the tip 🛠️.
Looks great but one thing I missed. Is how many times you need to twirl the plug the solder and the wire as you prepare to carry out this procedure and what music to play as you go about this great procedure
Twirl the plug, solder, and wire three times each for good luck 🪄🔌🎶.
Hi friend , I love your videos .
Thank you so much for your kind words! I'm glad you enjoy my videos 😊.
EXcelent Works.
Thankyou⚘
Thankyou for watching! I'm glad you found the tip helpful ⚘.
Nunca hubiera creído que se pudiera hacer tal truco de ingeniería espacial, de seguro el que realizó el video trabaja para una empresa de alta tecnología y es el jefe de investigación avanzada.
¡Gracias por tu comentario! ¡Me alegra que te haya gustado el truco de reparación del enchufe eléctrico! 🔧💡
@@CreativeMaster999
Woa jus good simple to do it👍👍
I'm glad you found the video helpful! Feel free to try out the method on fixing your electrical plug 🔌💡.
Has invventado el fuego jajajajajajaja
¡Sí! 🔥 En este video aprenderás un truco útil para arreglar un enchufe eléctrico roto. 😉.
Better than NEW !!!
Thank you! I'm glad you found the tip helpful! 💡🛠️
Fajne jest to, że autor promuje ideę naprawiania sprzętów domowych, a nie wyrzucania ich z powodu byle głupstwa i zaśmiecania Ziemi. Za to daję kciuka w górę!
Mam jednak dwie małe uwagi. Po pierwsze dość słabo wygląda ta pomarszczona czarna taśma izolacyjna, która w dodatku podczas dłuższego użytkowania tak naprawionej wtyczki będzie się rozklejała brudząc ręce i przewód klejem. Obwinięcie przewodów dratwą też nie jest dobrym rozwiązaniem. Zauważcie, że najczęściej przewody od wtyczek zalewanych odrywają sie w miejscu, gdzie kończy się tzw. odgiętka. Czyli tam, gdzie przewód wychodzi z nieco elastycznego plastiku wtyczki. Wtyczka naprawiona w sposób zaprezentowany nam na nagraniu zagrożona jest ponownym oberwaniem się przewodów przy twardym plastiku. I co wówczas możemy zrobić? Nic, już tylko wyrzucić wtyczkę.
Proponuję jeszcze przed zlutowaniem urwanych przewodów nałożyć na przewód grubościenną koszulkę termokurczliwą z klejem. Jej średnica musi być taka, by częściowo udało się ją naciągnąć na wąską część wtyczki. Po zlutowaniu przewodów i zabezpieczeniu miejsca połączenia koszulkami termokurczliwymi jak na nagraniu proponuję zamiast nawijania dratwy wzmacnianej klejem Super Glue, nawinięcie gęsto drutu miedzianego w izolacji np. fi 2 mm. Powstałą sprężynkę rozpoczynamy nawijać 2-3 cm od wtyczki, a kończymy już na niej. Ostatnie zwoje drutu po ściśnięciu na wtyczce w imadle należy ze sobą zlutować. Całość chowamy pod wspomnianą wcześniej grubościenną termokurczliwą koszulką. (Tych, którzy podejrzewają, że w sprężynce może się indukowac prąd od razu uspokoję - nic takiego nie będzie miało miejsca w przypadku używania przewodu do zasilania napięciem 230 V AC - tu pole elektromagnetyczne obu przewodów zasilających wzajemnie się znosi i nie oddziałuje na zwoje drutu, jakie sugeruję wykonać.)
Gdy teraz nawet znów oderwie się nam przewód za awaryjną odgiętką z miedzianej sprężynki, to naprawę będzie można powtórzyć, gdyż wciąż będziemy mogli dolutować przewody do końców przewodów wychodzących z wtyczki. Nie byłoby to możliwe w propozycji pokazanej na video.
No i na koniec - koszulki termokurczliwe należy raczej obkurczać gorącym powietrzem, a nie płomieniem zapalniczki, zaś izolację z przewodów zdejmować specjalnymi cążkami, a nie obtapiać.
Pozdrawiam serdecznie Kreatywnego Mistrza!
Dzięki za pozytywną opinię! Spróbuj użyć taśmy izolacyjnej o lepszej jakości, aby uniknąć tych problemów w przyszłości. 💡👍
Dziękuję bardzo.
Dzięki za oglądanie! 💡💪
The best.master
Thank you for your kind words! I'm glad you found the video helpful 👍.
7 million views for this??? Thats unbelievable 😳
Haha, sometimes the simplest fixes are the most surprising! 🔌🔧
Reported as potentially lethal advice.
Please remember to always exercise caution and consult a professional when dealing with electrical repairs. Safety first! 💡🔌
A repair that will work, but it is not safe and requires extra tools & parts. Much better option is a Leviton replacement plug at Home Depot for $2.47
I appreciate your suggestion, but this repair method is just an alternative for those who want to try something different! 😉.
No pls don't remove the video. It is beneficial
Please don't worry, I won't remove the video 🛠️. It's helpful for fixing broken electrical plugs!
Excellent
Glad you found it helpful! 💡🔌.
Good idea
Thank you for watching! 😊.
Tack😊
Tack för att du tittade! Hoppas det hjälper dig med din elektriska plugg! 💡🔌.
理解できました。
ありがとうございました。
理解してくれて嬉しいです！これからも役立つ情報をシェアしていきます🛠️。
The insurance adjuster likes this.
The insurance adjuster might find this tip helpful too! 😉🔌
Gracias
¡De nada! Espero que te haya sido útil el video. ¡Gracias por verlo! 😊.
E se esquentar, não pode pegar fogo?🔥
Não se preocupe! O vídeo mostra como consertar o plugue de forma segura, sem risco de incêndio. 🔌🔥.
Never cut toward yourself, always cut toward your friend.
Cutting towards your friend is definitely not the best advice here 🙅♂️ Always prioritize safety first and follow the proper techniques when fixing electrical plugs! ⚡
Large heat shink can be used to hold a severed finger tip in place until the nerve ends re-connect. Use soldering iron to heat the wrap. Use a sharp knife to remove wrap afterwards.
That's an interesting tip! Remember to always prioritize safety when handling electrical repairs 🔌⚠️.