Отлично! Я просто спаивал, но увеличение тока приводит к уменьшению срока. Попробовал Ваш способ, но сначала приклеил кусочек графита к ленте. Теперь проверяю долговечность. Спасибо.
Часто при сковыривании светодиода отлетает вся подложка изапаять трудно к оставшейся фольге на плате, я пользуюсь острыми маникюрными бокорезами. Раздавливая светодиод постепенно в порошок, тогда подложка сохраняется и достаточно одного движения паяльником чтобы замкнуть полоску в доли милиметра
@@DIA22322 для светодиода не критично незначительное изменение тока и напряжения, помню перепутали на изделии вместо 6 вольт припаяли 12 вольт , изделие прошло мороз и печь и морской туман на прогоне и только полковник военпред обратил внимание, что уж больно ярко горит светодиод нашли причину, перепаяли и на склад готовой продукции
Bro you are not the only one living in this world . There are more than millions of people who are struggling to even buy new bulbs financially and where they have to drive miles to just buy their daily needs
@@fredjones43 I've been replacing incandescents withe LEDs in our home for a while and wa-a-a-y too many fail prematurely. I've recently taken to marking on the base of the bulb the date I install it so I can get a clearer number of the failure rate.
всё проще: в канцелярский/пва/момент клей добавляем графитовый порошок, капаем на место удалённого диода, даём высохнуть. эл. проводность такого слоя достаточна для запитания цепи диодов, а сопротивление почти равно сопротивлению светодиода, поэтому прослужит долго. дарю идею.
@user-ye2xb1ih4e а я счас тебя, дикий, танцующий без бубна сэр с узкой фантазией, быстро "утоплю" своим ответом: "а нема паяльника, тока клей в наличие, и обгрызанный мышами карандаш, и лампа одна у тебя, и стырить негде" думай, кулибин 🤣
Reduce, Re-use, Recycle. Across the world, some have enough not to bother; some have little and guard it; some others have nothing and look for something to have. @DIYTechTren, I personally think you've done well. I also salute those who provided Active feedback.
Wish that I had the patience for doing these fixes... Great ideas for re-use and not just buying more, but (like most of us) I'm guilty of taking the easy way and not reusing. Shameful but true. 😊😊
Interesting fix using graphite from a pencil. However the small electrolytic capacitor (C1) near the center of the round circuit board is failing. You can tell because the plastic film on it has pulled back from the top of the capacitor body. This little repair will only last until that capacitor fails...sooner rather than later. Maybe you could do a video on simple surface mount soldering repair?
Hello! Thank you for watching the video and commenting. I appreciate your analysis! You can see how to repair LED bulbs by following the following link, I think it will be useful to you! Wishing you all good things ❤️❤️🥰😘😘 th-cam.com/play/PLsZfgoaDis-qgSmPeuoON7l88IVnFN5Tt.html&si=6TlDHYJRSSEOdxep
These kinds of bulbs are exclusively plastic. The better repair method is scrape away the defective led and solder that gap. I question how durable this fix is.
Если лампа сама по себе гавно дешевое, то она сгорит через неделю даже если добавить лишний светодиод. Лампам нормальных производителей пофиг недостаток одного. у меня корейская лампа горит уже год в гараже без проблем
Thank you so much dear friend! Just Use a Common Candle and Fix All the LED Lamps in Your Home! How to Fix or Repair LED Easy th-cam.com/video/pR-0J0OklCc/w-d-xo.html
Thank you for watching the video and leaving a comment. This is a temporary way to handle the situation where we lack tools and to completely handle the light bulb to work better, you should still replace the LED chip or buy a new one which is the perfect solution. Thank you and wish you the best
Merci d'avoir regardé la vidéo et d'avoir laissé un commentaire. Je suis heureux qu'elle ait été utile pour vous et pour tout le monde. Je vous souhaite le meilleur. Merci.
Que técnica tan práctica,el que sabe sabe.Gracias por compartir tan excelente contenido.Hoy he aprendido algo nuevo.Un abrazo enorme y que tengas mucho éxito en tus tutoriales.
¡Oh muchas gracias! ¡Me alegro que haya sido útil y para ti! Hay muchas formas de arreglar una bombilla. Esta es una de las formas de manejar temporalmente las emergencias. Para que la bombilla funcione de manera más efectiva y dure más, aún necesita reemplazar el chip LED o comprar una bombilla nueva. Gracias por ver. ¡Te deseo a vos y a tu familia lo mejor! Agradecer ❤😘😍
Excellent. Testing and repair with no special tools. Normal forceps and no soldering iron. Truly appreciable. Such recycle and reuse will help reduce waste..
Thank you for watching the video and leaving comments. Your feedback helps me improve the quality and gain more experience to develop further. Thank you and wish you all the best.
All your doing is bridging the 2 contacts with lead from the pencil, could you not just put a blob of solder across for the same result ?? a fix in 30 seconds...
Thank you for watching the video and leaving feedback. Each of your comments will help the channel become more complete and develop further! Wish you all the best!
Great tutorial.. The 2 bulbs I tried had all the LED working, just very low light output..seems this time a chip had gone, partly bad..maybe.. FYI..I wear a left hand glove for safety..
Congratulations, you did it, but the dim LED bulb is not as bright as the one next to it. Maybe you didn't make good contact with it. You should check again, or use the LED chip replacement method in the following video: th-cam.com/video/Jwb2lwGnkfw/w-d-xo.htmlsi=vxwqLxNJM94Rl2Lp
Он то может быть и умница! Кулибин! Но вот те, кто ставит ему лайки и пытается повторить его приколы, я в этом сомневаюсь. Вспоминаю старую поговорку услышанную от электриков -"Не знаешь техникини, не писай на провода". Сейчас буханка хлеба стоит больше, чем эта лампочка. Но вы же не отказываетесь от покупки хлеба. Статистика пожаров в квартирах и домах показывает, что виной всему хозяева жилья, которые пытаются самостоятельно чинить электроприборы вместо того, чтобы купить новые. Но на чужом опыте и чужой беде мало кто учится. Да и на своей тоже. Так что флаг вам в руки!
Es cierto que soldando un poco de estaño es más rápido, pero creo que él ha preferido mostrarnos la solución más fácil y al alcance de todos. No todo el mundo tiene un soldador en casa y ni mucho menos sabe usarlo. Personalmente, agradezco mucho la idea. Mil gracias, amigo.
Resulta que el soldar no provee la resistencia original del LED. Se quemaria un resistidor interno por el aumento de amperaje. Lo mejor seria remplazar el LED.
ES CIERTO LO QUE OPINAS ...PERO TENIENDO EN CUENTA QUE NO SERA EL UNICO LED QUE REPARARA`, ES CONVENIENTE TENER UN CAUTIN Y SOLDAR NO ES NADA DE OTRO MUNDO....HAY QUE MIRAR LOS TUTORIALES DE TH-cam...
Thank you for your comment! The Soloshion tap is indeed a great product, and using super glue will further improve its performance. Hope you continue to have a great experience!
Congratulations, you now understand how to make a resistor. Bad idea as you are now passing more current to the other LED's in the array and stressing the cap in circuit. The rest of the LED's will now fail faster. You need some resistance in the circuit, or the LED's in the circuit will fail faster. Diodes only pass voltage one way, unless it is a Zener, which will let half the forward voltage pass backwards. LED stands for Light Emitting Diode, and it has a low resistance value to make it illuminate.
Only slightly higher voltage across the other LEDs - they'll be fine for ages - especially if you drill a few googling holes in the opaque plastic "lens". It'd be quicker & better imo to dab a piece of solder on the led terminals.
Terima kasih telah menonton dan meninggalkan komentar Anda, ini adalah solusi sementara, saya memiliki video yang menunjukkan kepada orang-orang cara mengganti chip LED secara efektif, Anda dapat menontonnya lagi, terima kasih dan semoga berhasil: th-cam.com/video/Jwb2lwGnkfw/w-d-xo.html
Bonjour . Merci d'avoir regardé la vidéo et de commenter. C'est une façon temporaire de faire face aux situations d'urgence. Vous devez toujours remplacer la puce LED pour prolonger la durée de vie de la lampe. Merci et meilleurs voeux. Les meilleures choses
Gracias por ver el vídeo y dejar tus comentarios. Me alegro que te haya resultado útil. Si tienes alguna sugerencia para el próximo vídeo, por favor comenta y házmelo saber. Agradecer. Y te deseo lo mejor.
@@Алексей-у1ш7лотпаивай светодиод с одной лампы и паяй в другую .это будет значительно лучше ! При наличии нескольких перегоревших ламп! Я перегоревшие не выбрасываю !
Gracias por el video. Buena idea para arreglos temparales para los que no tenemos soldador. Nueva cultura de reutilizar ya que en mi pais esas lamparas son caras. Saludos desde Argentina 🇦🇷🇦🇷🇦🇷
Hello, I did it exactly in the time it took to do it. It didn't cut, paste or edit, so it took a bit of time, but everyone will understand how to do it clearly. Thank you and I wish you the best.
Good idea , of course , using a solder iron and little piece of wire to make a jumper for that LED will be much faster , but most people have no skills to do that , so this is good way to make it work 😊
That's a great point! While using a soldering iron and a small piece of wire can indeed be faster, not everyone has the skills or tools to do it. This method offers a practical alternative for many people.
You need some resistance in the circuit, or the LED's in the circuit will fail faster. Diodes only pass voltage one way, unless it is a Zener, which will let half the forward voltage pass backwards. LED stands for Light Emitting Diode, and it has a low resistance value to make it illuminate.
@@kriswingert1662 Good point , less Led's makes less resistance and more voltages are gonna dropped on other LEDs and it's will fail sooner , if it's was 4-5 LED's , but for this quantity , one LED it's just 5-7% , it's not gonna affect it much , right? 😉
За эти 10 минут я вам отремонтирую 3 таких лампочки. Во-первых испорченный светодиод видно сразу, на нем будет чёрная точка и не надо там ничем тыкать, проверять исправность каждого. Во-вторых не отвёрткой, а ножом быстро сковырнуть его с контактов. В-третьих, используя паяльник 40-70 Вт канифоль/олово пропаять это место, соединив оба контакта накортко. И не надо мудохаться тереть карандаш, искать наждачку именно этого номера, лепить там горбатого до стенки. Мутоты много, а качество ноль.
Fascinating repair job. At the beginning of my life, when I was broke with few options, this information would have been welcome and followed. Now, near the end of my life, I have many options but no time. Thank you for this video anyway. Yes, it was fascinating!
Fixed the open circuit - nice. As others have pointed out, a resistor would have been a bit better, to reduce the current going through the other LEDs. 8:00 No electrical tape here?
Hello dear friend! Thank you for viewing and commenting. This is a temporary solution. I will release a video showing how to replace it more effectively. I wish you luck and success.
¡Hola! ¡Qué buena idea! Una gota de soldadura realmente puede hacer una gran diferencia en la vida útil de la lámpara. ¡Gracias por compartir tu consejo! Un saludo. 🐤
What about keeping one bulb as a spare parts bulb and taking elements from it to replace the burnt out ones on others?
You would need to solder them on in general and not everyone is competent in such things!
Good idea!
А когда драйвер накрылся?
put solder blob on two point is easy and trust worthy
Solder small drop to connect both halves of the LED.
TOTALLY SAFE AND NOT ILLEGAL !!
This guy's channel is sponsored by Band-Aid.
Band-aid? I thought he was going to lose a thumb.
@@lancomedic That's what the super glue was for...
@@peatmoss4415 Hope his wife knows CPR
YES, that did get into dangerous for some of us... 😊😊
Отлично! Я просто спаивал, но увеличение тока приводит к уменьшению срока. Попробовал Ваш способ, но сначала приклеил кусочек графита к ленте. Теперь проверяю долговечность. Спасибо.
И как? Все еще светит?
Может, проще взять фольгу?
Dayandı mı?
Часто при сковыривании светодиода отлетает вся подложка изапаять трудно к оставшейся фольге на плате, я пользуюсь острыми маникюрными бокорезами. Раздавливая светодиод постепенно в порошок, тогда подложка сохраняется и достаточно одного движения паяльником чтобы замкнуть полоску в доли милиметра
@@DIA22322 для светодиода не критично незначительное изменение тока и напряжения, помню перепутали на изделии вместо 6 вольт припаяли 12 вольт , изделие прошло мороз и печь и морской туман на прогоне и только полковник военпред обратил внимание, что уж больно ярко горит светодиод нашли причину, перепаяли и на склад готовой продукции
I drove to the store and bought a new bulb before this video finished. 😂
Thank you for watching! I’m glad you found the time to grab a new bulb while enjoying the content!
Bro you are not the only one living in this world . There are more than millions of people who are struggling to even buy new bulbs financially and where they have to drive miles to just buy their daily needs
@@Nao20244poor people may not have all such tools and expertise to repair it. It is academically interesting.
Good guidance. But not everyone can do it.
Good for you😒
Well, theres 10 minutes 24 seconds of my life. I'm never getting back..!! 😂🏴👍
Yes but these bulbs are expensive- at least the 15-17 watt bulbs. And you know when they say they have a 10 year life, it really means 10 months.
Jajajaja jajajaja 😢jajajaja jajajaja jajajaja jajajaja jajajaja jajajaja. Y un lápiz dice
Wishing you always good luck and joy in life! Thank you for visiting the channel
Should have bowed-out the moment he used masking tape instead of electrical tape to insulate those tweezers.
@@fredjones43 I've been replacing incandescents withe LEDs in our home for a while and wa-a-a-y too many fail prematurely. I've recently taken to marking on the base of the bulb the date I install it so I can get a clearer number of the failure rate.
всё проще: в канцелярский/пва/момент клей добавляем графитовый порошок, капаем на место удалённого диода, даём высохнуть. эл. проводность такого слоя достаточна для запитания цепи диодов, а сопротивление почти равно сопротивлению светодиода, поэтому прослужит долго.
дарю идею.
Берём и паяем перемычку. А эти танцы с бубном для меня дикость. Дарю идею ; D
👍👍Вы бы лучше канал свой открыли, может ваши идеи намного больше просмотров бы получили. Даю идею)). 😊
Вам бы свой блог вести, четко подмечаете важное, много б посетителей собрали бы, даю идею ;)
@@СтарикПохабыч-я4хи мы тоже этот метод применяем, с паяльником. Быстрее и проще.
@user-ye2xb1ih4e а я счас тебя, дикий, танцующий без бубна сэр с узкой фантазией, быстро "утоплю" своим ответом: "а нема паяльника, тока клей в наличие, и обгрызанный мышами карандаш, и лампа одна у тебя, и стырить негде"
думай, кулибин 🤣
Reduce, Re-use, Recycle. Across the world, some have enough not to bother; some have little and guard it; some others have nothing and look for something to have. @DIYTechTren, I personally think you've done well. I also salute those who provided Active feedback.
Эхх🎉😢😅😊эх Юэ
❤
Wish that I had the patience for doing these fixes... Great ideas for re-use and not just buying more, but (like most of us) I'm guilty of taking the easy way and not reusing. Shameful but true. 😊😊
its shows we are recycle bulbs tat we think dont work but its only a part of it work which we can repair saving us not well off money
Interesting fix using graphite from a pencil.
However the small electrolytic capacitor (C1) near the center of the round circuit board is failing. You can tell because the plastic film on it has pulled back from the top of the capacitor body.
This little repair will only last until that capacitor fails...sooner rather than later.
Maybe you could do a video on simple surface mount soldering repair?
Hello! Thank you for watching the video and commenting. I appreciate your analysis! You can see how to repair LED bulbs by following the following link, I think it will be useful to you! Wishing you all good things ❤️❤️🥰😘😘
th-cam.com/play/PLsZfgoaDis-qgSmPeuoON7l88IVnFN5Tt.html&si=6TlDHYJRSSEOdxep
...and alot of LED bulbs are not plastic, but glass.
@@trekkiexb5, "You pays your money and you takes your chances". (On getting taken, that is.)
These kinds of bulbs are exclusively plastic.
The better repair method is scrape away the defective led and solder that gap. I question how durable this fix is.
I would have used super glue on the graphite
So inspiring!
😉🍀
چیره دست و هنرمندانه انجام دادید 🎉🎉🎉
خیلی ممنون! خوشحالم که خوشتون اومده. 🌟😊
Проще запаять, а при работе в30мин рядом сгорят ещё пару светодиодов, проверено временем
Здравствуйте, спасибо, что поделились своим опытом. Желаю вам всего наилучшего.
Если резистор поставить?
Если лампа сама по себе гавно дешевое, то она сгорит через неделю даже если добавить лишний светодиод. Лампам нормальных производителей пофиг недостаток одного. у меня корейская лампа горит уже год в гараже без проблем
@@EnverHarisoglu, ты в гараже живешь? или включил и оставил там ее на год?
"Пофиг недостаток одного" ?
Что еще за "недостаток" светодиода?
Недостаток образования или опыта работы? 😂
Они соединены ПОСЛЕДОВАТЕЛЬНО.
Congratulations !
Good things for the young people.
My grandson is very, very interested.
Thank you so much big friend! Have a nice day ❤️😘🍀
Don't let your grandson do this, it's too dangerous, using live wires.
İşe yarıyor,Bende video dan bakıp yaptım.Bazıları için Basit ve saçma olabilir emeğine sağlık😊👍
5:41 Your way of repairing the LED light is very creative. Thanks to your video, I saved money without having to buy a new light
Thank you so much! I'm glad you found the repair method helpful. Saving money and fixing things yourself is always satisfying. Happy to have helped!
@@DIYTechTrends Thank you and wish you more success
@@DIYTechTrends 🩷🩷🩷
Muchas gracias!! Desde Argentina
Que manera de complicar el arreglo, cuando con un punto de estaño se resuelve. Con el grafito dejará de funcionar enseguida.
Verdade mesmo concordo plenamente com você.
O con un pedacito de papel aluminio...
10:24
Estaño para los que tienen soldador.
Yo no tengo soldador.
Entonces si no uso grafito que podría utilizar según vos?
Un soldador para este trabajo es muy barato. Lo compras y ya lo tenés.
По черной точке можно определить сгоревший светодиод,выпаять и каплю олова нанести и готово.Быстрей и лучше Учись.
Привет! Спасибо за просмотр видео и комментарий. Желаю вам всего хорошего ❤️❤️❤️
Toda razón menos pasos y más efectivo
@@DIYTechTrends Не у всех есть паяльник, поэтому большое спасибо за данный метод.
Этот вариант подходит скорее для офисного ремонта.
Или кусочек фольги
My favourite part was the paper masking tape insulation
Так ето самая лучшая изоляция в мире
❤ good job. Greeting from an Indonesia
Hi friend! love indonesia
Es mejor, más rápido y seguro con una gota de estaño. Muchas gracias por tu video, todo sirve.
¡Gracias por el consejo! ¡Seguro que probaré esa técnica la próxima vez! 😉
Better I would think to replace faulty LED chip or bridge with suitable resistor?
Thank you so much dear friend!
Just Use a Common Candle and Fix All the LED Lamps in Your Home! How to Fix or Repair LED Easy
th-cam.com/video/pR-0J0OklCc/w-d-xo.html
Yes, an instructive and interesting cover, but to fix it I spend at least 30 minutes, during this time I buy at least 8 new lamps like this))))
Thank you for watching the video and leaving a comment. This is a temporary way to handle the situation where we lack tools and to completely handle the light bulb to work better, you should still replace the LED chip or buy a new one which is the perfect solution. Thank you and wish you the best
thinking same BUT its prob from a poor country area ect , still interesting from electronics point of view
Câteodată, în diverse țări de pe planetă, e foarte complicat sa cumperi becuri led noi....
Just rem how much these cost when they first came out. Ten min was/is a deal
Waste not, want not. The era of automatic disposal may not always be.
Wow! You saved $2.00 and it only took a half-hour or more!
Жирная лампочка за два доллара!
Этим заняться можно только для своейпотребности интереса-сделаю или нет и всё! Я пойду и куплю.
People with money spend money to save time. People with time spend time to save money. There’s room for all.
Друг. Это как с рыбалкой. Потратил полдня и кучу денег на бензин и прикормки. Варил кашу собирался а потом мыл сапоги. У тебя есть хобби, друг?
Cheaper than $2 in France. In fact a couple of years ago the government was giving them away (practically) 20 or was it 30 for 2€.
It was the most amazing thing I've ever seen.
Love you
Thank you.
Excellent.
Salutation from Brazil.
Hi Brazil 🇧🇷❤️Thank you so much
Très facile à comprendre et à appliquer pour tout le monde, merci ça m’à été très bénéfique
Merci d'avoir regardé la vidéo et d'avoir laissé un commentaire. Je suis heureux qu'elle ait été utile pour vous et pour tout le monde. Je vous souhaite le meilleur. Merci.
Que técnica tan práctica,el que sabe sabe.Gracias por compartir tan excelente contenido.Hoy he aprendido algo nuevo.Un abrazo enorme y que tengas mucho éxito en tus tutoriales.
¡Oh muchas gracias! ¡Me alegro que haya sido útil y para ti! Hay muchas formas de arreglar una bombilla. Esta es una de las formas de manejar temporalmente las emergencias. Para que la bombilla funcione de manera más efectiva y dure más, aún necesita reemplazar el chip LED o comprar una bombilla nueva. Gracias por ver. ¡Te deseo a vos y a tu familia lo mejor! Agradecer ❤😘😍
Policía 🚔 cárcel francisco remedios todos
Thanks very much. I 'll try my level best. There are lot of bulbs...
Mashallah mashallah a job Allah AP ko Kuch rak hum NY ya video pr kam Kya ha but acha ha good 👍 theak ❤❤❤😊😊😊
Super 👌 Deutschland 🇩🇪
Thank you so much dear friend! nice day
You presented very clearly and coherently, I followed and saw that you did not stop at all
Thank you so much
😂
"Глупость-это не отсутствие ума, просто это ум такой... "
Привет! Спасибо за просмотр видео и комментарий. Желаю всего самого лучшего вам и вашей семье ❤️🍀😘
@@DIYTechTrends да и вам всего наилучшего...
Золотые слова генерала Лебедя.
Salom man organib oldim sizdan minnaddorman raxmat
I don't know what he was doing but it helped 👍
Thank you for watching the video and leaving comments. Wish you always luck and success. Please continue to give me feedback.
Dear good guidance, practical helping display Thanks again
Когда коту делать нечего, он ...... Лампы ремонтирует😂😂😂
Не шалит и примусы починяет.
когда их в хозяйстве более 50 и сгоревших накопилась штук 500 можно и карандашом ремонтировать!
😊умный кот не будет.
Съездить за лампой = час + стопицот рублей. Починить данным методом = 10 минут + 10 копеек.
Сижу никому не мешаю лампу починяю, тут вы.
Grazie per questo video. Credo che lo stagno è più efficace della matita 👍
Policía cárcel francisco
Clever! I have several to try this on.
Thank you for watching the video and leaving a comment. I'm glad you like it. Wishing you the best
Que belleza de trabajo,muchas gracias por compartir tus conocimientos,saludos desde Medellín Colombia.
Good job bro 🎉
thank you very much my friend
Тпатом пажар небудит
Excellent. Testing and repair with no special tools. Normal forceps and no soldering iron. Truly appreciable. Such recycle and reuse will help reduce waste..
Thank you for watching the video and leaving comments. Your feedback helps me improve the quality and gain more experience to develop further. Thank you and wish you all the best.
All your doing is bridging the 2 contacts with lead from the pencil, could you not just put a blob of solder across for the same result ?? a fix in 30 seconds...
not everyone have the tools for soldering, but everyone can get a pencil easily.
or aluminum foil. this video took 10 times longer than it needed to.
La mina del lápiz no resiste mucho tiempo, yo lo probé, es mejor unirlas con soldadura de estaño.
A blob of solder is too big.
Bricoleur du dimanche quoi 🤢💩🤮🚽🚾
A wonderful help and teaching thank you so much
Thank you for watching the video and leaving comments. Wish you always luck and success.
It was amazing, congratulations and a great ending, it also reached 1,000 points
Thank you for watching the video and leaving feedback. Each of your comments will help the channel become more complete and develop further! Wish you all the best!
Selamün aleyküm çok şahane oldu helal size usta
Videoyu izlediğiniz ve yorum bıraktığınız için teşekkür ederiz. Çok mutluyum çünkü size ve herkese faydalı olacak. En iyi dileklerimle
Great tutorial..
The 2 bulbs I tried had all the LED working, just very low light output..seems this time a chip had gone,
partly bad..maybe..
FYI..I wear a left hand glove for safety..
Congratulations, you did it, but the dim LED bulb is not as bright as the one next to it. Maybe you didn't make good contact with it. You should check again, or use the LED chip replacement method in the following video:
th-cam.com/video/Jwb2lwGnkfw/w-d-xo.htmlsi=vxwqLxNJM94Rl2Lp
Вот какой ты умница!
У меня их сколько лежат собраные.!слышала что можно сделать.молодец.
Он то может быть и умница! Кулибин! Но вот те, кто ставит ему лайки и пытается повторить его приколы, я в этом сомневаюсь. Вспоминаю старую поговорку услышанную от электриков -"Не знаешь техникини, не писай на провода". Сейчас буханка хлеба стоит больше, чем эта лампочка. Но вы же не отказываетесь от покупки хлеба. Статистика пожаров в квартирах и домах показывает, что виной всему хозяева жилья, которые пытаются самостоятельно чинить электроприборы вместо того, чтобы купить новые. Но на чужом опыте и чужой беде мало кто учится. Да и на своей тоже. Так что флаг вам в руки!
@@AleksandrKopachev такой длинный ответ от продавца лампочек!😂
C'est une très bonne idée, merci bcp.
Thank you so much for your kind words! I really appreciate your support!
Спасибо за ваш комментарий! Мне очень приятно знать, что мое видео оказалось полезным.
Gracias un saludo desde Venezuela, felicitaciones
Thank you so much ! nice day
Thanks a lot for your lovely vdo
Thank you for watching the video and leaving a comment. Wishing you much luck and success,
Es cierto que soldando un poco de estaño es más rápido, pero creo que él ha preferido mostrarnos la solución más fácil y al alcance de todos. No todo el mundo tiene un soldador en casa y ni mucho menos sabe usarlo.
Personalmente, agradezco mucho la idea.
Mil gracias, amigo.
Resulta que el soldar no provee la resistencia original del LED. Se quemaria un resistidor interno por el aumento de amperaje. Lo mejor seria remplazar el LED.
K@@thomasperez4422
Se esta sobrecargado a los demas led ,si se quita el malo y no repone por un bueno ,si no se hace aumenta el voltaje .
ES CIERTO LO QUE OPINAS ...PERO TENIENDO EN CUENTA QUE NO SERA EL UNICO LED QUE REPARARA`, ES CONVENIENTE TENER UN CAUTIN Y SOLDAR NO ES NADA DE OTRO MUNDO....HAY QUE MIRAR LOS TUTORIALES DE TH-cam...
@@thomasperez4422Если у вас заложенно, чтоб светодиод горел через n количество часов, то нужно подобрать правильное сопротивление ,вместо диода.
Отличное видео для тех у кого нет денег и магазина и паяльника и свечи. когда ночью нужен свет срочно.
Рассмешил!!!))) Ночью, когда "свет нужен срочно" садиться и ремонтировать лампу??? )))) Может, лучше до утра с фонариком перетерпеть? ))))
@@ГеннадийИванов-х7эС фонарём под глазом
😊.
soloshion tap is throwing after hoting the bulb ..the good working you take super glo
Thank you for your comment! The Soloshion tap is indeed a great product, and using super glue will further improve its performance. Hope you continue to have a great experience!
Excellent 🎉
Thank you! Cheers!
Você é um gênio parabéns!!!!!
Obrigado por assistir o vídeo e deixar um comentário, que bom que gostou. Desejo-lhe sorte e sucesso. Agradecer
Obrigado pela dica.
Mas não seria mais prático soldar led queimado?
voce nao sae lo que esta falando, se precisa la utilizaçao de gominha de mascar
Congratulations, you now understand how to make a resistor. Bad idea as you are now passing more current to the other LED's in the array and stressing the cap in circuit. The rest of the LED's will now fail faster. You need some resistance in the circuit, or the LED's in the circuit will fail faster. Diodes only pass voltage one way, unless it is a Zener, which will let half the forward voltage pass backwards. LED stands for Light Emitting Diode, and it has a low resistance value to make it illuminate.
Thank you dear friend, nice day!
Do you have a solution? The bulb was useless before.
Only slightly higher voltage across the other LEDs - they'll be fine for ages - especially if you drill a few googling holes in the opaque plastic "lens". It'd be quicker & better imo to dab a piece of solder on the led terminals.
Nice fix, but I could have gone to the store and got a new one by the time it’s taking to fix the old one.
Orlando, FL🏝️😎
Great fix. Environmentally best
Thanks for watching the video and leaving a comment. Have a nice and happy weekend.
చాలా చక్కని పరిష్కారం ఉంది ధన్యవాదాలు
చాలా ధన్యవాదాలు
سلام اخي شكرا كثيرا
سلام ! ممنون که ویدیو رو دیدید و نظر دادید. با تشکر و آرزوی بهترین ها برای شما
asal.saya.dari.sul.sel
❤
Terima kasih telah menonton dan meninggalkan komentar Anda, ini adalah solusi sementara, saya memiliki video yang menunjukkan kepada orang-orang cara mengganti chip LED secara efektif, Anda dapat menontonnya lagi, terima kasih dan semoga berhasil:
th-cam.com/video/Jwb2lwGnkfw/w-d-xo.html
To naprawdę działa!!! ❤❤❤
To naprawdę działa! Cieszę się, że metoda pomogła Ci naprawić lampy LED w domu. 💡🔧
מדהים❤ תודה🙏
You are very smart....I love cleaver people. Keep up the videos. They are fun to watch.
Thank you so much! I'm really glad you enjoy my videos. I'll keep making more fun content. Have a great day!
magique mais la tension augmente sur les autres cellules donc la durée de vie baisse mais beau sauvetage, bravo !
Bonjour . Merci d'avoir regardé la vidéo et de commenter. C'est une façon temporaire de faire face aux situations d'urgence. Vous devez toujours remplacer la puce LED pour prolonger la durée de vie de la lampe. Merci et meilleurs voeux. Les meilleures choses
Muchas gracias!!
Gracias por ver el vídeo y dejar tus comentarios. Me alegro que te haya resultado útil. Si tienes alguna sugerencia para el próximo vídeo, por favor comenta y házmelo saber. Agradecer. Y te deseo lo mejor.
Obrigada, por compartilhar sua dica conosco! ❤❤❤❤❤❤
De nada! Fico feliz que tenha gostado da dica! ❤️❤️❤️❤️❤️
Gracias por sus soluciones. God bless you
Aprecio mucho tu comentario. Me alegra saber que mis soluciones te han ayudado. ¡Dios te bendiga!
Я выбросил штук 20 таких ламп, нужно было просто пропаять один светодиод, спасибо автору, очень полезно.
Их потом не надолго хватает. Пробовал паять. Потом надоело.
@@Алексей-у1ш7лотпаивай светодиод с одной лампы и паяй в другую .это будет значительно лучше !
При наличии нескольких перегоревших ламп!
Я перегоревшие не выбрасываю !
É só dar um pingo de solda. muito mais fácil!!!
Mais fácil comprar outra lâmpada.
Talvez a solda não seja tão boa condutora, que nem o grafite.
Gracias por el video. Buena idea para arreglos temparales para los que no tenemos soldador.
Nueva cultura de reutilizar ya que en mi pais esas lamparas son caras.
Saludos desde Argentina 🇦🇷🇦🇷🇦🇷
Great work! Thanks! ;)
Thank you so much! I'm glad you liked it! :)
Me gusta el video gracias por compartir
Thank you so much dear friend ❤️❤️❤️
Поекрасная альтернатива поставить "перемычку" без паяльника. Молодец! 😊
Thank for watching
this video way longer than needed.
Hello, I did it exactly in the time it took to do it. It didn't cut, paste or edit, so it took a bit of time, but everyone will understand how to do it clearly. Thank you and I wish you the best.
Estoy de acuerdo: en 3 minutos era suficiente. Como dicen en mi rancho: "mucha crema para un taco"
Yes, buy a new one.
⁷@@DIYTechTrends
Good idea , of course , using a solder iron and little piece of wire to make a jumper for that LED will be much faster , but most people have no skills to do that , so this is good way to make it work 😊
That's a great point! While using a soldering iron and a small piece of wire can indeed be faster, not everyone has the skills or tools to do it. This method offers a practical alternative for many people.
You need some resistance in the circuit, or the LED's in the circuit will fail faster. Diodes only pass voltage one way, unless it is a Zener, which will let half the forward voltage pass backwards. LED stands for Light Emitting Diode, and it has a low resistance value to make it illuminate.
@@kriswingert1662 Good point , less Led's makes less resistance and more voltages are gonna dropped on other LEDs and it's will fail sooner , if it's was 4-5 LED's , but for this quantity , one LED it's just 5-7% , it's not gonna affect it much , right? 😉
I'm impressed! But I personally wouldn't bother.
Thank you for watching the video and leaving a comment Wishing you the best
За эти 10 минут я вам отремонтирую 3 таких лампочки. Во-первых испорченный светодиод видно сразу, на нем будет чёрная точка и не надо там ничем тыкать, проверять исправность каждого. Во-вторых не отвёрткой, а ножом быстро сковырнуть его с контактов. В-третьих, используя паяльник 40-70 Вт канифоль/олово пропаять это место, соединив оба контакта накортко. И не надо мудохаться тереть карандаш, искать наждачку именно этого номера, лепить там горбатого до стенки. Мутоты много, а качество ноль.
Бро, а как же магия?😅
Совершенно верно
Shorting a bad LED will make an already too high current even worse, just put a surface mount resister in it's place
Das Graphit ist der Widerstand.
Considering how inexpensive they are, now, JUST REPLACE IT unless you're bored.
Hello, sometimes it is not convenient for us to buy balls, so we also need skills, just in case we use them.
@@DIYTechTrends just keep a few spares in stock. Often these bulbs come in boxes of 3 or 4
*NEXT WEEK HOW TO SAVE TOILET PAPER USE BOTH SIDES*
Hahahahaha
Never use the edge of the toilet paper due to risk of paper cuts 😅
@Owenearl2505 We can safely assume you are a folder and not scruncher And we'll on your way to your first million.
Попробуй подмываться и бумага будет не нужна. Что делать с водой- разберёшься
Fascinating repair job. At the beginning of my life, when I was broke with few options, this information would have been welcome and followed. Now, near the end of my life, I have many options but no time. Thank you for this video anyway. Yes, it was fascinating!
Smart man and awesome repurpose projects please keep it up
Thank you and nice day
un petit point de soudure pour bypasser la led défectueuse est préférable 😉
This interesting I’ve this method with aluminum foil with superglue also. This a short lived solution to further failures of the bulb
The 'lead' powder from the pencil is a resistor. The foil isn't a good resistor. It is more like a conductor than a resistor.
За это время можно обучиться пайке..
I love it 💓
Thank you so much dear friend friend ❤️☘️
Fixed the open circuit - nice.
As others have pointed out, a resistor would have been a bit better, to reduce the current going through the other LEDs.
8:00 No electrical tape here?
No spare led , would a replacement rectifier diode avoid the overvoltage.
Hello dear friend! Thank you for viewing and commenting. This is a temporary solution. I will release a video showing how to replace it more effectively. I wish you luck and success.
😅 4:25
I went to the store and bought a new light bulb. When I got back this video was still running.
❤️❤️❤️
I went to the store and there were no light bulbs. I came back home and had to restart the video from the beginning.
Если нужно сделать быстро.
Отличный вариант.
👍👍👍
good tips for life
Thank you so much for your kind words! I'm really happy you enjoyed the tips.
@@DIYTechTrends oh yes thank you for much
This is pretty amazing.
Thank you so much dear friend! Nice day 😘❤️❤️☘️☘️
Shockingly awful. Really shocking. Lethally shocking. Never, ever do this as shown. Ever. It could be the last thing you do.
😂😂😂😂😂😂😂12volts
Absolutely! He had a live socket there all the time.
I don't think that's a 12 volt bulb . That's an 120 AC bulb.@@edisonapp
Yes.. you are correct friend. I also opened the bulb.why to sacrifice your life for a penny..my wife told.
Your wife is spot on.
Не проще один раз паяльком ткнуть ? Чем 10 минут тормозить.
Привет. Благодарим вас за просмотр видео и оставленный комментарий. Желаю вам всего наилучшего, спасибо
Я паять не умею а бумажку присабачить смогу, и электричество жечь не надо, надо быть эконмным во всем
где ты в офисе паяльник возьмёшь?
They last so long ,,why bother,,,,just get a new one. Got tired waiting for the pencil.
Hello! Thank you for watching the video and commenting. Wishing you all good things ❤️❤️❤️
Warren Buffet??
Можно же было вслух озвучить, устанешь тут с вами...
Hola DIYTech Trends!
Lo mejor es una gota de soldadura para alargar un poco más la vida útil de la lámpara...
Un saludo!🐤
¡Hola!
¡Qué buena idea! Una gota de soldadura realmente puede hacer una gran diferencia en la vida útil de la lámpara. ¡Gracias por compartir tu consejo!
Un saludo. 🐤
Muy ingenioso 👏👏👏
❤️❤️❤️❤️😘😘😘
Nice effort, but your disregard of safety procedures and personal danger is not worth the effort in rescuing a two-dollar lightbulb.