I love the jobs when things are stuck and difficult chance to get the big toys out of their boxes and have a play. I have a forty ton hollow ram cylinder that makes pulling bushings a breeze. It also does a great job of pulling stuck injectors out like carrots out of a sandpit!
I need this done to my International. It appears the International Airliner and Freightliner Airliner are one and the same and use the same pins and bushings. I have a feeling that buying this tool, pump, and fittings would cost way too much for a one time use so I need to find a shop that has these tools already in Indiana to do this for me.
How did you get the two bolts out that hold the bushing to the hanger itself? I am working on a 94 fld120 and I can not bust those lose with anything I have? I have put a 3/4 drive breaker and cheater pipe on them and I have used an 1100ft lb impact and they aren't budging. The nuts came right off
Hey Andrew, have you tried using heat and then an impact wrench? The hanger is aluminum so it corrodes pretty bad with the bolts. You could also try heat and then an air hammer as well.
Would a little lubricant help to install and or a wheel to clean out old material in spring or not recommended? Asking for a friend, good as Porta-Power, good job and video.👍👍🇺🇸🇺🇸🇺🇸
would this install and or remove the pin and bushing in a 1999 kenworth w900l sway bar (suspension is ag( air glide) 400 also what about front leaf springs and bushings what tool or tools do I need to do both?
These manufacturers often choose different suspension designs for their vehicles based on a variety of factors, which can include both threaded and rubber-isolated pins.
Hi I been having a hard time trying to find the website to all the tools you need to make this one could you please help me out and share with me all the websites where you can buy all the parts especially that hydraulic tube.
Here is a link to the main 15000 Pin & Bushing Starter Kit. Once you are on this page, you can click the Adapter Kits button and enter 15030 to see that one. You can also call us at 1 800 661 4661 with any questions and our customer service team will help you out. tigertool.com/products/pin-bushing-starter-kit
I am interested in purchasing what about the rear bushing removal and installation on a 99 Kenworth w900l I need a tool to remove and install. Please reach out I am ready to purchase from you or a distributor
It actually there to prevent the center pin from being pulled Torn from the rubber bushing. The washer seats on the outer metal bushing shell and it pulls the center pin and the outer shell togther and evenly.
VGAPR Garage you don't want it to be lubed. You want it right tight and dry. The Bushing should not move once set. Using lube will cause it to move, and possibly begin corrosive breakdown of the isolation bushing.
*PRICE MAKES A SENSE IF YOU REPLACE SEVERAL BUSHINGS EVERY SINGLE DAY, BUT IN ANY OTHER CASES PRICE IS STUPIDLY WAY TOO HIGH FOR THAT LITTLE HYDRAULIC PRESS!*
![일상 속 기분 좋음 [Proto disco meme]](http://i.ytimg.com/vi/DwmEIaZ7XGQ/mqdefault.jpg)
Visit our website for more information: tigertool.com/products/15030-pin-bushing-adapter
Holy crap! That's probably one of the coolest tools I've seen in a long time.
I love the jobs when things are stuck and difficult chance to get the big toys out of their boxes and have a play. I have a forty ton hollow ram cylinder that makes pulling bushings a breeze. It also does a great job of pulling stuck injectors out like carrots out of a sandpit!
40tons on an injector! Omg. :)
We just purchased this tool. Really excited to try it out tomorrow.
so we have this and the jost 5th wheel adaptor. just awesome tools. we work in upsate new york so we know rust.
thanks tiger
Thanks Chris!
Wow, that’s one neat tool
Freezing the bushings help as well.
Ok, ill just back the truck into my freezer.
I need this done to my International. It appears the International Airliner and Freightliner Airliner are one and the same and use the same pins and bushings. I have a feeling that buying this tool, pump, and fittings would cost way too much for a one time use so I need to find a shop that has these tools already in Indiana to do this for me.
We do this job down in Texas if you ever ride down here give us a call lol it’s probably the easiest job to get done down here
@@d-e-a8209 contact information please. I want the bushings replaced on a 15 cascadia, I already have all six bushings. Just looking for a shop.
@@pytn520 9562702562 Send me a message to help you
How did you get the two bolts out that hold the bushing to the hanger itself? I am working on a 94 fld120 and I can not bust those lose with anything I have? I have put a 3/4 drive breaker and cheater pipe on them and I have used an 1100ft lb impact and they aren't budging. The nuts came right off
Hey Andrew, have you tried using heat and then an impact wrench? The hanger is aluminum so it corrodes pretty bad with the bolts. You could also try heat and then an air hammer as well.
Would a little lubricant help to install and or a wheel to clean out old material in spring or not recommended? Asking for a friend, good as Porta-Power, good job and video.👍👍🇺🇸🇺🇸🇺🇸
would this install and or remove the pin and bushing in a 1999 kenworth w900l sway bar (suspension is ag( air glide) 400 also what about front leaf springs and bushings what tool or tools do I need to do both?
Why are the pins on my freightliner /Peterbilt kit screw ins and not push in like these? @tigertool
These manufacturers often choose different suspension designs for their vehicles based on a variety of factors, which can include both threaded and rubber-isolated pins.
It’s around $2,500 for this complete tool. That’s a lot for a dyi.
Thats why you go to a shop for theses jobs
Hi I been having a hard time trying to find the website to all the tools you need to make this one could you please help me out and share with me all the websites where you can buy all the parts especially that hydraulic tube.
Here is a link to the main 15000 Pin & Bushing Starter Kit. Once you are on this page, you can click the Adapter Kits button and enter 15030 to see that one. You can also call us at 1 800 661 4661 with any questions and our customer service team will help you out. tigertool.com/products/pin-bushing-starter-kit
I am interested in purchasing what about the rear bushing removal and installation on a 99 Kenworth w900l I need a tool to remove and install. Please reach out I am ready to purchase from you or a distributor
@Tiger tools how can I buy this tool I don’t see it in your website
tigertool.com/products/15030-pin-bushing-adapter
Most of these pins come with a flange on the inner side thats attached to the metal bushing. Can this tool remove that style?
Yes however you have to flip the tool around and service from the inboard side of the spring.
@@TigerTool Yeah, and remove the driveshaft because there's not enough room.
What’s the idea of putting the socket on the opposite end of the bush that it’s pulling from? Seems to me it doesn’t do anything?
It ensures that the bushing pin and bushing comes out as one assembly.
It actually there to prevent the center pin from being pulled Torn from the rubber bushing. The washer seats on the outer metal bushing shell and it pulls the center pin and the outer shell togther and evenly.
Thanks for the way to fix thing
That machine is a stick but if they are well damaged and it does not have a metal base, the only way is to assemble everything
Who's the name this tools
why didn't you clean the inside than add grease
sergio solis because they are supposed to not move. you want them froze in there. I think they are put in with lock tight from the factory
LOL
Will this work on an international suspension iross
Do you have the part number for the pin & bushing you are looking to replace?
Q precio tiene el es tractor idrablico
Cómo algo para conseguir una de esas erramientas
Precio de esa herramienta $$$
how much? ? cost ??
2200 $ the starter kit
Necesito conprar esta erramients conpleta pero noce como hacerlo
Clean out the hole, add some lube to the bushing, it would have went in a lot easier.
VGAPR Garage you don't want it to be lubed. You want it right tight and dry. The Bushing should not move once set. Using lube will cause it to move, and possibly begin corrosive breakdown of the isolation bushing.
Sweet
donde venden esa herramienta
nice .....
*PRICE MAKES A SENSE IF YOU REPLACE SEVERAL BUSHINGS EVERY SINGLE DAY, BUT IN ANY OTHER CASES PRICE IS STUPIDLY WAY TOO HIGH FOR THAT LITTLE HYDRAULIC PRESS!*
That kit is ridiculously expensive. 2400 plus taxes. Hell nah.
Sale and mexico?
Fuck no grease no lube straight in in in.!!! I need one.
exelente
Qué no abra algo más económico espero que si
dont freeze those bushings.
Hola donde puedo conpral esa heramie ta
Daniel Sanchez yo las vendo
@@ezequielacosta5549 en cuanto sale esta herramienta
@@ezequielacosta5549 te agradezco si me das información
Conrado Zamora dame tu numero de telefono y te mando fotos y videos de la maquina.
@@ezequielacosta5549 9211300373
Toss some never seize and buff the bore pal
I’ll just buy a new truck it’s easier and prob around the same price as the tool
Me gusta
Santiago Altamirano
you can make this tool without hydraulics.
Yes you can but the job is easier and safer with a little help from the hydraulics.
spacebandit what u need to make this tool
vá porque vá ......
Better use mask,