The broken front axle of the truck, I did a joint for the first time that no one dares to do

แชร์
ฝัง
  • เผยแพร่เมื่อ 3 พ.ค. 2024
  • Correct repair procedure in case of broken front axle of truck due to overload which not every mechanic can do
    #repair #correct #broken #front #axle #truck #overload #mechanic
  • ยานยนต์และพาหนะ

ความคิดเห็น • 22

  • @dadbehrouhbakhsh626
    @dadbehrouhbakhsh626 19 วันที่ผ่านมา +2

    The axle broke due to a combination of overloading and bad roads..I'm not sure how long this new welded axle will hold to the same treatments..

  • @chickenlife6317
    @chickenlife6317 24 วันที่ผ่านมา +3

    RIP truck driver.

    • @mutterschied
      @mutterschied 19 วันที่ผ่านมา

      Why? The welded surfaces 'r' stronger than when processed, you engineer...

  • @user-dj5gf9jp8g
    @user-dj5gf9jp8g 24 วันที่ผ่านมา

    Cool work thanks 👍

  • @zecasiqueira9262
    @zecasiqueira9262 13 วันที่ผ่านมา

    Esse rapaz de óculos e bom de torno e proficional

  • @j.conxcara381
    @j.conxcara381 3 วันที่ผ่านมา

    ya que han hecho una reparación tan chapucera, podrían haberlo compensado poniéndole un refuerzo.

  • @holycrapski
    @holycrapski 8 วันที่ผ่านมา

    A little knowledge is a dangerous thing (For others in this Case).

  • @PeterChapman-rg6gr
    @PeterChapman-rg6gr 23 วันที่ผ่านมา +1

    Some poor truck driver is going to regret that this bodge was ever fitted to his lorry.

  • @thomasbor
    @thomasbor 21 วันที่ผ่านมา +1

    say good bye to castor and camber angles....

  • @TheUltimate65
    @TheUltimate65 24 วันที่ผ่านมา

    Did the have Full controll over the camber angle then...🤔

  • @user-si5qz7rp7b
    @user-si5qz7rp7b 23 วันที่ผ่านมา +2

    СТО раздолбай моторс придумало новую технологию восстановления передней балки всем перекупам нужно срочно брать с них пример.

    • @Bosjak63
      @Bosjak63 20 วันที่ผ่านมา

      Посмотрел твои видео
      Раздолбай моторс как раз у тебя, у них хотя бы в цеху чисто
      Да и технология реставрации балки несмотря на кажущуюся примитивность вполне рабочая, это видно по тому как они её исполнили. Сразу заметно что не в первый раз !

    • @user-si5qz7rp7b
      @user-si5qz7rp7b 19 วันที่ผ่านมา

      @@Bosjak63 у меня хоть верстак и тиски есть.

    • @user-si5qz7rp7b
      @user-si5qz7rp7b 18 วันที่ผ่านมา

      @@Bosjak63 чтобы кого ни будь критиковать за бардак и грязь в цеху нужно иметь хотя бы гараж а не арендованное парковочное место.

    • @Bosjak63
      @Bosjak63 18 วันที่ผ่านมา

      @@user-si5qz7rp7b Тут проблем нет..
      Был гараж - был порядок
      Сейчас арендованое парковочное место, ничего не изменилось - так же в чистоте и порядке!

  • @mrphotomanseattle
    @mrphotomanseattle 24 วันที่ผ่านมา +1

    Please explain why they drilled and drove in the pin. Is it for stress relief?

    • @bills6093
      @bills6093 24 วันที่ผ่านมา +3

      The pin makes the joint stronger since they were only able to weld around the outside. So the pieces are both pinned and welded together. Probably should have used a shorter pin that set below the surface a bit, and then welded the pin in place at both ends. Such a repair in the West would get you arrested, though.

    • @AlirezA_TEX
      @AlirezA_TEX 23 วันที่ผ่านมา

      Maybe for more strength than the central part

    • @AlirezA_TEX
      @AlirezA_TEX 23 วันที่ผ่านมา

      ​@@bills6093exactly

    • @AlirezA_TEX
      @AlirezA_TEX 23 วันที่ผ่านมา

      ​@@bills6093exactly

  • @freshhealthy8118
    @freshhealthy8118 24 วันที่ผ่านมา

    ❤❤❤❤