If I have an AIO which headers do I connect to? Atm I have the rad fans connected to the CPU header and the pump connected to the CPU_OPT. It doesn't show the pump speed so I just set it to Full speed mode. Im also running two front fans on a spitter on sysfan2 and a third front fan on sysfan1. My back fan is run on sysfan3. Should I switch the back and pump fan headers since sysfan3 is also labeled pump or does it not really matter since I manually set CPU_OPT full speed for the pump. Thanks in advance.
I would have done exactly why you did. I would also be curious of temps if you swapped sysfan3 and cpu_opt. But you configured it manually so I wouldn't be concerned.
I have built a machine with this board (Gigabyte B650 Gaming X AX). I have a 2GB SSD, AMD Ryzen 9 7900x, and Windows 11. I finally got Windows installed using a flash drive, but when I went to restart the computer without the bootable USB, it did not start, and I got a blue screen with no bootable device found. I tried changing the boot options and finally gave up. how should I set up the CSM support and secure boot? what am I doing wrong?
Thank You for your time. How do you set bios to boot from cd drive ? These newer set up menus are full of technical stuff and nothing to help you get going.
Here’s my issue: I have no idea what to do at this point. I have a Lian Li ALC 360 Coolant System and a Gigabyte B650 X AX V2 Motherboard (note: the Lian Li pump cable only has a 3 pin socket that still will fit on the 4 pin motherboard header. I have the pump plugged into the system pump 4 pin on the motherboard. I have the other cable of the two plugged into the CPU Fan Header on the mother Board. Nothing is plugged into the CPU_Opt. The lights on the pump come on, but the fans do not move nor does it recognize/detect the CPU Fan or the Pump in the BIOS. Both says N/A. It does however stay at about 37 degrees. No recognition of coolant fans at all. My only issue with this new build.
had some random restarts which culminated into a failure to boot with the red CPU/DRAM lights alternating on the mobo. Turned EXPO off after clearing CMOS and seeing how it goes. Any issues with your system with EXPO? I have the similar microcenter bundle w/ 7800x3d, CL32 gskill flare x5, and b650 gaming X AX v2.
@ssdrmstre I am also planning on getting the micro center bundle, but have heard some complaints about this motherboard. Are there any updates to your situation?
I have the same mobo and 7800x3D currently on FB would you recommend upgrading to what’s recommended in gigabyte control centre? That would be FA2. I’m nervous about updating. Any issues with FB and frying the chip?
Going through the gigabyte control center would be a good option if it is your first time updating. I go through bios, but it doesn't matter where you do it from and that is more steps than from the Gigabyte control center. One reason to do the upgrade is you will get security fixes and other updates like AGESA updates. When you do the update be patient, It will take some time. I hope this calms your nerves. Let me know how it goes.
Hi, I've got the first version of this mobo and the bios looks like how it does in this video and not how it does in your video for it. It's on version FA2 and I'm trying to update the BIOS to potentially fix a performance issue. I have no experience with updating a BIOS so I'm being extra careful. Is it normal for the original version to have this layout?
I did a video on the bios of the original version and it does look different. It is not uncommon that these manufactures will update the look over bios updates. If you update thru the bios flash tool they should verify the correct version and rev of the board before the flashing starts.
@@yoshiofred I would not say complete, because power outages and there is a chance of a bad flash. I have had that once in 20 years of building computers, many years ago. I have gone thru q-flash and accidently selected a different bios I had on a USB and it didn't allow me to update.
@@GrayaOverload Well the BIOS update worked out, but for some reason my issue still persists. Oh well. Appreciate your replies! Updating a BIOS really isn't as hard as I thought it was.
Might be a stupid question, but how do I get from here to booting the system. Just built my first PC and bought an OS usb from windows directly l.. but can’t work out how to get from this screen to starting the PC?? Any and all help appreciated.
From this screen. You should see boot devices. Make sure that your USB drive is one of the devices. If it is then when you reboot it should boot off the windows USB install.
Hi there! I have this mb and face this problem. When i first builded the PC my BeQuite! Dark Rock Elite cooler's LED was on and working fine. Suddenly one day stopped. The guys from BeQuite have send a replacment cup it doesn;t work as well. They suggest it must have been turned of somewhere in BIOS settings but i cannot find anywhere a setting for this...
You only installed the cooler and nothing else changed? What do you mean by CPU not working as well? CPU has Higher temps or not boosting as high? If you didn't change anything else and just the cooler I would expect it to be the same. You can reset the defaults in bios to see if that helps, but if that doesn't change anything there is something else going on.
@@GrayaOverload The cooler is running and all pc works fine. Just cooler's light went off suddenly. I replaced the light cup, not working too. So it is not the hardware. Some setting shut down the led, but I cannot find such a setting in bios
Hey, question. I had 2x ( 16gb ) g skill trident rams in I bought two more (16gb ) but I get stuck in boot loop. If I’m not mistaken I have to set the timing and etc manually on my MB BUT all these videos don’t show anything for my specific motherboard so everything is listed and probably named different. I’m trying to configure and tweak the timing etc but don’t know where exactly to go do so. Can you possible help ?
I can try. Before tweaking memory timing. If you just boot with new 2 memory sticks, does it boot fine? If that works put all 4 sticks in and reset bios. I am guessing you are on the latest bios and that these are the same model memory.
@@GrayaOverload thank you for the fast and quick reply. I am NOT on the latest bios. I am aware I have to manually update my bios by visiting gigabyte and searching my MB and downloading the latest update to a flash drive. Then inserting the usb flash in the red usb port ( usb bios ). I was just missing a flash drive which I will be getting my hands on today. Prior to all this information I filled you in with. At times it would start “ normally “ with slll four rams same brand same speed and same 16gb x2 ( the two new I added ) when I enable xmp and hit save and exit it would go into a boot loop. My fans and everything else would start up normally but after it’ll just go into a boot loop and the fans won’t turn on. So I went and removed the cmos coin to reset my bios and did it again this time around I enabled xmp, low latency & bandwidth. Same thing happens. The only way is if I do not go into bios and let the pc start up with out going into bios. I tried that twice and it seems like that’s the only way it’ll boot w out entering bios and enabling xmp
It is weird on the entering bios and it boot looping. I would try bios first. Just to confirm both sets work with xmp enabled if you only have that one set in?
@@GrayaOverload so I am currently running only 2 rams on A2 &B2 and they are working with xmp enabled. Also when it does decide to boot with all four rams still installed my rams mhtz are at 3k which is under performing but with just two it’s giving me a higher number can’t remember exactly how much
Ok, I wanted to make sure each set work at the same xmp without the other set installed. I know Ryzen can have issue when going to 4 stick. Bios updates sometimes help get past that before having to tweak memory in the bios. Let me know what the state is once you update the bios. That will give me some time to boot into bios on my gigabyte AMD system and take a look at and refresh me on all the memory settings again.
bhai pls tell, do we need a UPS for a gaming Pc coz sometimes I face power cuts issue here..... So do we need it or it can work on inverter UPS which is based on SINEWAVE technology by GENUS around 10 yrs old but the batteries are new...... Pls suggest My gaming pc specs are CPU - RYZEN 5 7600X GPU - 4060TI MOTHERBOARD - Gigabyte B650 M Gaming X AX AIO - Deepcool 240mm PSU - 650W GOLD DEEPCOOL
Greetings . A question ..the V2 Motherboard is more newer than the default was released? Is compatible with Linux? Because I use only Linux the last 5 years
Yes, it is a newer version I did an unboxing of this mobo that went over the differences. biggest different is default doesn't support the 8000G series processors. I would think this would work on Linux. My friend that got this uses windows so I never tested.
Can you make a video on how to adjust the setting on this board to get better performance and not go overboard with over clocking I’m new to pc have same cpu and ram and board would really like some more information
Let me see if I can. It is a friends PC I built and he is gaming already. It is a great idea. I really need a bench to be able to do this sort of thing
@@GrayaOverload yeah it's a big ask, but nowhere on the internet is there any kind of info on how to actually use this interface, so it would be great to go a bit more in depth.
Hello there Graya, any idea how to change the ram frequency? mine has a EXPO mode 6400 but unfortunately, fails memtes86 on both XMP/EXPO mode, so i heard i could tweek it down to 6000. i tried to SPD setup, clicked on the USER box and put in 6000 but it doesnt seem to save.
If you don't have expo enabled, does it pass mem test? I need to look again, but I thought if you have expo off you could then tweak the memory. I hope to get some time this weekend to look again.
I have this motherboard with the 7700X. Randomly I experience a "half reboot" where the power will be on and the fans are working but the screen is off and everything else unresponsive, the PSU has to be turned off at the switch; The red light CPU is on. I'm not sure of its the MB or the CPU. I took the motherboard back for repair as they said there was a pin missing. When I got it back repaired it did the half reboot again 3 days later and has got back to randomly everyday. Has anybody else experienced this? The bios is on F21 currently and F9 prior.
Can I get full specs of the system (including psu model)? I have seen this before on different systems but normally is a pain to diagnose. I have seen bad PSU, bad memory, gpu issue, etc.
Thanks. Nothing jumps out. Everything looks like it should be quality. When this happens is it under load or are you just started doing something or waking from sleep?
@GrayaOverload it's completely random. Could be when it's boosting or trying to. There are no logs for me to check. Nothing sure if it's the Aio not on properly or cpu faulty. Also happens when just browsing.
I have spent many hours trying to figure out a problem like that, and it could be just about anything. Your memory is stock speed? Do you have another power supply to test?
Wondering if you might be able to help with an issue. Seem to have the same build. Having a current issue where I plug in my headphones (Logitech G35 USB) and everything is fine. Audio is perfect, but if I go into mic settings or if I join voice chat in Diablo 4 it seems like it struggles to recognize the mic. Audio starts cutting in and out repeatedly while the headset begins appearing and disappearing as recognized device.
I don't know much about that headset. One thing I would make sure you have the latest AMD chipset drivers. I am guessing you already went thru the game settings. How many USB devices do you have plugged into the computer?
@@GrayaOverload Think I got it figured out somewhat. Plugging into the front ports presents some level of communication issues. Plugging directly into the back of the MB seems to have resolved the issue.
Would need the hardware ID's out of the device manager. To get that open device manager, next right click on device and click properties. Go to device tab, switch to the device tab and change property to Hardware Ids.
I built my pc with the same mobo/cpu combo. Got it up and running but my network adapter/wifi is not working. I tried getting the software from the website and installing but seems the install won’t take. I tried reinstalling windows 2x and still not working properly. I have not tried to update the bios (never done it before) but would that be the missing piece I need to update?
It shouldn't be. I updated to the latest before installing Windows. So, I can't verify if that would have helped. I think Gigabyte has an issue with putting the right drivers on the right page. Not 100% sure yet, but I have been looking at all these revs on a few different boards. One way I go through and find the driver is to go to the device manager, right-click on the device that needs help, and click properties. In Properties, click on the details tab. change the property to Hardware Ids. I will copy the top id and search it to verify what device it is and what driver I need. That normally points me to the right driver in the support page or the search will put me on the path to the right direction. If you want paste that path in here or reach out to me and I can take a look as well.
sorry fo all the questions but i finally built the pc and was wondering if there was a fan controller for the case fans for some reason they dont show on my fan control app for my cpu i have a good fan curve set for my gpu and cpu but my case fans are i think on max always they are very loud I have a LANCOOL 216 any help would be appreciated
I had a build recently in the lancool 216 airflow that didn't have a fan controller for case fans in the version I bought and I plugged them into the motherboard. They were all fine with fan speed. If you did buy the version with a fan controller and plugged them into it you probably have some other way to control it, buttons or software depending on the fan controller. I hope I helped.
I have the same case. My fans aren’t load tho. I’m having other issues, I can’t figure out if it’s the motherboard or cooling system. Lian Li Case 216 v2 Lian Li ALC 360 Coolant System Gigabyte B650 Gaming X AX Motherboard. I have my pump connected to Fan3/System Pump. I have the CPU_Fan Connected to the CPU_Fan Header on the motherboard. Nothing in the CPU_Opt. The Coolant Pump lights up, but the fans do not and they don’t move. Inside the BIOS, it says N/A for the CPU_Pump and the CPU_Fans. I have no idea what’s going on with this. Everything else shows in the BIOS.
Building the same exact builds with parts today, and I see that my AGESA Ver is ComboAM5PI 1.1.0.1 rather than 1.1.0.2b. Will this effect anything and will I be able to change it in the future? If so, how would I go about that and is it important? Sorry i am noob, first time building pc
If you update you bios the agesa ver should update to the one that comes with the bios. I hope this helps. Sorry for the slow reply this comment was held for review for some odd reason
Hello there - i got the same motherboard but not sure if i should update my bios my version is F2. A2 and B2 RAM slot is working for only 1 of my RAM but when i put that RAM on A1 and B1 its not working but my 2nd RAM doesn't work on all of them. I'm guessing Motherboard and RAM both bad?
Looking for a good board for ryzen 7800x3d, 32gb 6000mhz cl30 ram and a 4080 super. Is this the board to get or is there better boards for similar price?
I think this is a fine board for that setup. My friend had something close to this I built for him, and it works great. If you read thru all the comments some people did have issues, but they sound like doa board, which has happened to me many times over the years with different brands. I would recommend testing boards in the return window. Overall a good board. I wish I was able to go thru more boards, to have a more to compare to.
this mobo is very good. the most common reason for doa is a bad ram capacitor. happened to me so i just returned the mobo and got a replacement. no big issue. just inconvenient to swap out mobo's.
did you ever had issues with dram. i recently got this same mobo and ram and it will only post with one stick of ram. do you know anything to fix this issues?
We can't seem to get the Wifi to turn on. So we can't install our version of Windows 11 from USB. It requires a connection. Any way to turn wifi on prior to installing windows?
@@quirkylwj I don't think Windows has the driver for that card on the install yet. You could try the shift+f10 method to bypass. If that doesn't work you can use Rufus to remove that part of the install. I have used the shift+f10 and have a video on this. That would be the simplest and then install the drivers when windows is installed. There is a way as well to add the drivers to install and setup, depending on the effort you want to try. It is frustrating that MS cares so little for users it makes the setup hard to complete.
Hello, how can I change the fan settings like yours? I can't click on that scale at the smart fan page. I dont understand why it is not allowing me to click on it to add and adjust the dots on the scale
@@GrayaOverload yes i had . also red ddr lights . cleared cmos again and did the q flash bios update . still red ddr . after hitting del key mutiply times system is up and running
I don’t actually know HOW to download new drivers like WiFi so I can get a network connection. I have this same motherboard so I’m wondering where to find the needed drivers and every step to actually get my drivers update. I have been stuck on windows 11 set up and don’t know what to do to progress.
Quick update: Spoke to micro center and managed to get WiFi drivers installed. There were two different drivers: AMD WIFI driver and Realtek WiFi drivers (there was a 4 digit number attached to the “Realtek ____ WiFi driver” that I don’t quite remember right now). (Quick notice: I followed a tutorial to do the windows 11 set up without WiFi which involved opening up commands and typing something in then selecting a many option at windows 11 network set up) The issue when using a laptop to download the drivers to a flash drive was that I unzipped the folder with the driver before transferring it to my computer. That was why it did not install. So after getting the AMD WiFi driver instead of the Realtek WiFi driver, and properly installing it by unzipping and double clicking in the correct computer, everything started to work.
TL;DR: Bypassed windows 11 set up with a command Used separate laptop to download “AMD WiFi driver” from gigabytes website list of drivers (Gigabyte Gaming X AX V2 M.B.) Plugged the flash drive with the WiFi driver into new PC then unzipped + installed. Installed the rest of my needed drivers after connecting to WiFi.
Hi, my xmp/expo profile is disabled and no profiles option, i have same motherboard/cpu as yours ... ddr5 auto booster is enough for this rams? ( CORSAIR VENGEANCE DDR5 RAM 32GB (2x16GB) 4800MHz CL40 Intel XMP iCUE Compatible Computer Memory )
@@GrayaOverload I figured it out, I had a 6000hz memory but when I clicked XMP it stayed at 4000 but I had to save and exit and boot up bios again for it to change that’s why I was so confused but thanks for reaching out
Can you help me with a boot issue… on this motherboard I plug in the jump drive with the windows 11 boot tool…the boot menu pops up but when I get to select drivers there are no drivers shown…even in the bios the flash drive does not pop up in the bootable devices… this is a brand new build
I will work on trying to get a video on that. This is my friends machine and I have to get him to bring the machine back over to record. Luckly, he lives closer to me then some of the other builds I have done.
Hello, now I have a problem, that when I turn on the PC I see abnormal ram consumption, I understand that it may be a failure in the RAM refresh. the board generates a short beep
@@GrayaOverload When I am already in Windows with the task manager I see a consumption of 10 to 15 GB of ram, with only the basic startup services, at this point I restart the computer and when I return to Windows I now see the normal startup consumption that It is 4 to 5 GB of ram... in Windows I do not have any red LED on the board
@@brayancamilo9247 thanks for that information. Sounds like a windows or a program install issue. When you see the high memory usage and open task manager the details tab you can select and then sort by memory. That should then give you the process that is using the memory.
Hello, how about I update from Version FB to FA2 but I still can't activate tpm 2.0 to be able to update to Windows 11, apart from that I don't know why two GPUs appear in my resource manager and one appears with PCI/VEN_100... do you know how I can activate the TPM?
To update bios Gigabyte does have some information on that but you can use their Windows tool @BIOS which is in the Gigabyte Control Center. You can also download the bios for your board put it on a USB and then use the flash tool in bios to update it. I don't know what you mean by Activate tpm. This board and the other video you posted this exact question on don't need to update bios for Windows 11 support, for other security fixes it probably will need a bios update. To see the TPM details open Windows Security, then click on Device Security, From there it will either have a security processor or say "Standard Hardware Security not supported". If you are on a different board that is older then you probably will need an update to get Windows 11 and default the tpm 2.0 to on. As far as the PCI/VEN_100 I would look at your device manager and make sure all devices have drivers. I would need to know more then just PCI/VEN_100.
@@GrayaOverload Thank you very much for the prompt response, I already updated the Bios to the FA2 version, an interface appears like in your video, I have Windows 10 Pro and I want to update to Windows 11, I get that TPM 2.0 must be compatible, I have not been able to activate it in the bios with FA2 version... As for the device manager in the display adapter, I get PCI\VEN_1002&DEV_164E&SUBSYS_D0001458&REV_C6 I had not seen it before updating the Bios, my question is if it is normal
Did the TPM get enabled in Windows after the update? There is a ftpm that you should get enabled and that should then allow you to get Windows 11. For device manager. That is an AMD Display device, Did you download the Radeon software? it might even be in Windows update in optional updates.
@@GrayaOverload in settings --> miscellaneous --> Trusted platform module I have the following options. * Auto *Disabled *Enable dTPM *Enable ASP fTPM *Enable Pluton fTPM I have enabled all the options and none of them always work for me in Windows it keeps telling me that I do not have TPM 2.0 active, maybe I'm incorrectly activating the tpm in the bios For the AMD display device I have not downloaded the radeon software, do you recommend downloading it?
Did you try to apply defaults to the BIOS? When I have done a few machines that needed the bios update I reset to defaults. Yes, I do especially if you play games.
You can do it manually if it doesn't have a expo or xmp profile. I would have to look at it again, it has been a bit since I tweaked it manually. I have had goo success with the profiles.
@@IBaknam if it is running fine, I would go with it. If you do run into issues then remember what the memory is at go to stock to see if that is an issue. If it is then, that is when ibwiuld manually tune to 6000
I have the same exact specs but mine is stuck on 4800 mt/s instead of 6000 mt/s this happened after updating the bios. I've tried changing the xmp, expo profiles frequenzy and nothing works. anyone know how to fix this?
I have not seen this issue. It could be a bug in the bios. When you set expo/xmp that should activate the memory profile. You could reach out to gigabyte support.
Might be another video, to explain all the options or a video on a few options. I will look at doing that. Just going thru bios takes a while let along explain. :) Thanks for the feedback.
How do i change the boot order. Whenever i get to boot menu and select my drive it doesn't start. But as soon i get into bios my drive usb drive isn't detected BUT it will try to start which it can't
@@GrayaOverload Okay, good. I hope thats the case for me cause ill be getting the bundle from Micro Center with the 7800X3D Have you had any other issues ?
8:43 my Power on by keyboard is Off yet my keyboard can turn on the PC, anyone know How do I disable it? I got a feeling it's because my keyboard is connected via the PS/2 port. Also the RGB on my mouse stay on after shut down. Anyone has solutions?
Depends. If you flash in the bios no. If you are using the bios flashback then yes. The Bios flashback is where you put power to the motherboard and then press the button on the back of the mobo to flash it.
The bios is always stuttering with these 7k chips. I have the 7800x3D and I've never had a worse bios experience.. had a 3770k, 5930k, 9600k, 10400, 12600k, etc in various PCs..first time AMD and never had such a bad bios experience.
@@Vdhm91 do you have a different mouse to try. If you have different dpi setting it can produce this. I mostly use a keyboard. But I seen this on different bios from time to time. Depends on the mouse implementation in bios.
@@GrayaOverload I know it's the 7k chips. Another video I watched had made the same comment and a friend of mine has the same issue. We both just got our 7800x3Ds with this mobo.
@@toutloffc1 How did you fix it exactly? I think I downloaded a corrupted file into the drive I put into my pc possibly damaging my ssd. Not too sure it’s my first pc.
@@OFFICIALZAR422 you need to go to gigabyte support site and download the driver. You will need to make sure you have the right version and revision for the correct drivers.
lol , he is only reading the options
Yep
If I have an AIO which headers do I connect to? Atm I have the rad fans connected to the CPU header and the pump connected to the CPU_OPT. It doesn't show the pump speed so I just set it to Full speed mode.
Im also running two front fans on a spitter on sysfan2 and a third front fan on sysfan1. My back fan is run on sysfan3.
Should I switch the back and pump fan headers since sysfan3 is also labeled pump or does it not really matter since I manually set CPU_OPT full speed for the pump.
Thanks in advance.
I would have done exactly why you did. I would also be curious of temps if you swapped sysfan3 and cpu_opt. But you configured it manually so I wouldn't be concerned.
cpu pump goes to system fan 4 slot, and event it written PUMP on it.
I have built a machine with this board (Gigabyte B650 Gaming X AX). I have a 2GB SSD, AMD Ryzen 9 7900x, and Windows 11. I finally got Windows installed using a flash drive, but when I went to restart the computer without the bootable USB, it did not start, and I got a blue screen with no bootable device found. I tried changing the boot options and finally gave up. how should I set up the CSM support and secure boot? what am I doing wrong?
Thank You for your time. How do you set bios to boot from cd drive ? These newer set up menus are full of technical stuff and nothing to help you get going.
@@elcues in the easy screen the middle right should allow you to click and drag bootable devices. If a one time click F8 to select the drive
Here’s my issue:
I have no idea what to do at this point.
I have a Lian Li ALC 360 Coolant System and a Gigabyte B650 X AX V2 Motherboard (note: the Lian Li pump cable only has a 3 pin socket that still will fit on the 4 pin motherboard header. I have the pump plugged into the system pump 4 pin on the motherboard. I have the other cable of the two plugged into the CPU Fan Header on the mother Board. Nothing is plugged into the CPU_Opt. The lights on the pump come on, but the fans do not move nor does it recognize/detect the CPU Fan or the Pump in the BIOS. Both says N/A. It does however stay at about 37 degrees. No recognition of coolant fans at all. My only issue with this new build.
have you found the reason for the error
@@Robin-vu4vu Attach pump to cpu-opt
had some random restarts which culminated into a failure to boot with the red CPU/DRAM lights alternating on the mobo. Turned EXPO off after clearing CMOS and seeing how it goes. Any issues with your system with EXPO?
I have the similar microcenter bundle w/ 7800x3d, CL32 gskill flare x5, and b650 gaming X AX v2.
I didn't run into any issues. Did you upgrade your bios to the latest?
@@GrayaOverload yep F3. system continued to crash after disabling EXPO as well. Will promptly return it to microcenter as soon as I can make the drive
That is what I would do as well. I am glad My friends didn't have an issues, not a short drive for us to make.
Ubdate bios system.
@ssdrmstre I am also planning on getting the micro center bundle, but have heard some complaints about this motherboard. Are there any updates to your situation?
I have the same mobo and 7800x3D currently on FB would you recommend upgrading to what’s recommended in gigabyte control centre? That would be FA2. I’m nervous about updating. Any issues with FB and frying the chip?
Going through the gigabyte control center would be a good option if it is your first time updating. I go through bios, but it doesn't matter where you do it from and that is more steps than from the Gigabyte control center. One reason to do the upgrade is you will get security fixes and other updates like AGESA updates.
When you do the update be patient, It will take some time. I hope this calms your nerves. Let me know how it goes.
@@GrayaOverload thank you! I haven’t seen any issues on the current version so will hold off for now. The usb route seems straight forward enough.
Hi, I've got the first version of this mobo and the bios looks like how it does in this video and not how it does in your video for it. It's on version FA2 and I'm trying to update the BIOS to potentially fix a performance issue. I have no experience with updating a BIOS so I'm being extra careful. Is it normal for the original version to have this layout?
I did a video on the bios of the original version and it does look different. It is not uncommon that these manufactures will update the look over bios updates. If you update thru the bios flash tool they should verify the correct version and rev of the board before the flashing starts.
@@GrayaOverload So updating through Q-Flash is completely safe? Thank you for such a quick reply btw!
@@yoshiofred I would not say complete, because power outages and there is a chance of a bad flash. I have had that once in 20 years of building computers, many years ago. I have gone thru q-flash and accidently selected a different bios I had on a USB and it didn't allow me to update.
@@GrayaOverload Well the BIOS update worked out, but for some reason my issue still persists. Oh well. Appreciate your replies! Updating a BIOS really isn't as hard as I thought it was.
@@yoshiofred hope you get your issue figured out
Might be a stupid question, but how do I get from here to booting the system. Just built my first PC and bought an OS usb from windows directly l.. but can’t work out how to get from this screen to starting the PC??
Any and all help appreciated.
From this screen. You should see boot devices. Make sure that your USB drive is one of the devices. If it is then when you reboot it should boot off the windows USB install.
Hi there! I have this mb and face this problem. When i first builded the PC my BeQuite! Dark Rock Elite cooler's LED was on and working fine. Suddenly one day stopped. The guys from BeQuite have send a replacment cup it doesn;t work as well. They suggest it must have been turned of somewhere in BIOS settings but i cannot find anywhere a setting for this...
You only installed the cooler and nothing else changed? What do you mean by CPU not working as well? CPU has Higher temps or not boosting as high? If you didn't change anything else and just the cooler I would expect it to be the same. You can reset the defaults in bios to see if that helps, but if that doesn't change anything there is something else going on.
@@GrayaOverload The cooler is running and all pc works fine. Just cooler's light went off suddenly. I replaced the light cup, not working too. So it is not the hardware. Some setting shut down the led, but I cannot find such a setting in bios
I didn't right anything about CPU. The led cup of the Elite.
Ah, sorry for the confusion. I think you need to download the gigabyte software to control the LED's. I can't remember what it is called.
@@GrayaOverload Done that too... It refuses to collaborate
Hey, question. I had 2x ( 16gb ) g skill trident rams in I bought two more (16gb ) but I get stuck in boot loop. If I’m not mistaken I have to set the timing and etc manually on my MB BUT all these videos don’t show anything for my specific motherboard so everything is listed and probably named different. I’m trying to configure and tweak the timing etc but don’t know where exactly to go do so. Can you possible help ?
I can try. Before tweaking memory timing. If you just boot with new 2 memory sticks, does it boot fine? If that works put all 4 sticks in and reset bios. I am guessing you are on the latest bios and that these are the same model memory.
@@GrayaOverload thank you for the fast and quick reply. I am NOT on the latest bios. I am aware I have to manually update my bios by visiting gigabyte and searching my MB and downloading the latest update to a flash drive. Then inserting the usb flash in the red usb port ( usb bios ). I was just missing a flash drive which I will be getting my hands on today. Prior to all this information I filled you in with. At times it would start “ normally “ with slll four rams same brand same speed and same 16gb x2 ( the two new I added ) when I enable xmp and hit save and exit it would go into a boot loop. My fans and everything else would start up normally but after it’ll just go into a boot loop and the fans won’t turn on. So I went and removed the cmos coin to reset my bios and did it again this time around I enabled xmp, low latency & bandwidth. Same thing happens. The only way is if I do not go into bios and let the pc start up with out going into bios. I tried that twice and it seems like that’s the only way it’ll boot w out entering bios and enabling xmp
It is weird on the entering bios and it boot looping. I would try bios first. Just to confirm both sets work with xmp enabled if you only have that one set in?
@@GrayaOverload so I am currently running only 2 rams on A2 &B2 and they are working with xmp enabled. Also when it does decide to boot with all four rams still installed my rams mhtz are at 3k which is under performing but with just two it’s giving me a higher number can’t remember exactly how much
Ok, I wanted to make sure each set work at the same xmp without the other set installed. I know Ryzen can have issue when going to 4 stick. Bios updates sometimes help get past that before having to tweak memory in the bios. Let me know what the state is once you update the bios. That will give me some time to boot into bios on my gigabyte AMD system and take a look at and refresh me on all the memory settings again.
bhai pls tell, do we need a UPS for a gaming Pc coz sometimes I face power cuts issue here..... So do we need it or it can work on inverter UPS which is based on SINEWAVE technology by GENUS around 10 yrs old but the batteries are new...... Pls suggest My gaming pc specs are CPU - RYZEN 5 7600X GPU - 4060TI MOTHERBOARD - Gigabyte B650 M Gaming X AX AIO - Deepcool 240mm PSU - 650W GOLD DEEPCOOL
You don't need one but I do receommand one. As long as it produces a pure sinewave.
Greetings . A question ..the V2 Motherboard is more newer than the default was released?
Is compatible with Linux? Because I use only Linux the last 5 years
Yes, it is a newer version I did an unboxing of this mobo that went over the differences. biggest different is default doesn't support the 8000G series processors. I would think this would work on Linux. My friend that got this uses windows so I never tested.
Can you make a video on how to adjust the setting on this board to get better performance and not go overboard with over clocking I’m new to pc have same cpu and ram and board would really like some more information
Let me see if I can. It is a friends PC I built and he is gaming already. It is a great idea. I really need a bench to be able to do this sort of thing
@@GrayaOverload yeah it's a big ask, but nowhere on the internet is there any kind of info on how to actually use this interface, so it would be great to go a bit more in depth.
@@ivocanevo great idea I will try that on another gigabyte motherboard I have.
just run everything standard. no need to overclock anything because its superfast already and you will not benefit from any tweaking.
Thoughts on the low latency/high bandwith options? Any real gaming benefit to enabling these?
I don't have any opinion on it. I would have to try it out, run normal task with it on and off to decide.
Hello there Graya, any idea how to change the ram frequency? mine has a EXPO mode 6400 but unfortunately, fails memtes86 on both XMP/EXPO mode, so i heard i could tweek it down to 6000. i tried to SPD setup, clicked on the USER box and put in 6000 but it doesnt seem to save.
If you don't have expo enabled, does it pass mem test? I need to look again, but I thought if you have expo off you could then tweak the memory. I hope to get some time this weekend to look again.
I have this motherboard with the 7700X. Randomly I experience a "half reboot" where the power will be on and the fans are working but the screen is off and everything else unresponsive, the PSU has to be turned off at the switch; The red light CPU is on. I'm not sure of its the MB or the CPU. I took the motherboard back for repair as they said there was a pin missing. When I got it back repaired it did the half reboot again 3 days later and has got back to randomly everyday. Has anybody else experienced this? The bios is on F21 currently and F9 prior.
Can I get full specs of the system (including psu model)? I have seen this before on different systems but normally is a pain to diagnose. I have seen bad PSU, bad memory, gpu issue, etc.
@GrayaOverload
These are my specs
AMD Ryzen 7 7700X CPU 8 Core / 16 Thread - Max Boost
- Gigabyte B650 GAMING X AX ATX Motherboard For AMD Ryzen 7000 Series CPUs - AMD B650 Chipset
- G.SKILL Flare X5 32GB DDR5 Desktop RAM Kit 2x 16GB - 5600MT/s - CL36 - 1.2V - 36-36-36-89
- Cooler Master MWE Gold 850W Power Supply 80 Plus Gold
- Cooler Master MasterLiquid Lite ML240L V2 240mm AiO Water Cooling with aRGB Fans
- Gigabyte NVIDIA GeForce RTX 4070 Gaming OC 12GB GDDR6X
Thanks. Nothing jumps out. Everything looks like it should be quality. When this happens is it under load or are you just started doing something or waking from sleep?
@GrayaOverload it's completely random. Could be when it's boosting or trying to. There are no logs for me to check. Nothing sure if it's the Aio not on properly or cpu faulty. Also happens when just browsing.
I have spent many hours trying to figure out a problem like that, and it could be just about anything. Your memory is stock speed? Do you have another power supply to test?
Wondering if you might be able to help with an issue. Seem to have the same build. Having a current issue where I plug in my headphones (Logitech G35 USB) and everything is fine. Audio is perfect, but if I go into mic settings or if I join voice chat in Diablo 4 it seems like it struggles to recognize the mic. Audio starts cutting in and out repeatedly while the headset begins appearing and disappearing as recognized device.
I don't know much about that headset. One thing I would make sure you have the latest AMD chipset drivers. I am guessing you already went thru the game settings. How many USB devices do you have plugged into the computer?
@@GrayaOverload Think I got it figured out somewhat. Plugging into the front ports presents some level of communication issues. Plugging directly into the back of the MB seems to have resolved the issue.
Good to hear.
What wifi/bluetooth drivers should i install? As there's both AMD drivers and Realtek drivers
Would need the hardware ID's out of the device manager. To get that open device manager, next right click on device and click properties. Go to device tab, switch to the device tab and change property to Hardware Ids.
Still confused on what the hardware ids mean. I’m currently stuck on the windows 11 network set up and don’t know which drivers to download and how
@@erick6712 You need to have windows installed before you can get hardware ids
I built my pc with the same mobo/cpu combo. Got it up and running but my network adapter/wifi is not working. I tried getting the software from the website and installing but seems the install won’t take. I tried reinstalling windows 2x and still not working properly. I have not tried to update the bios (never done it before) but would that be the missing piece I need to update?
It shouldn't be. I updated to the latest before installing Windows. So, I can't verify if that would have helped.
I think Gigabyte has an issue with putting the right drivers on the right page. Not 100% sure yet, but I have been looking at all these revs on a few different boards. One way I go through and find the driver is to go to the device manager, right-click on the device that needs help, and click properties. In Properties, click on the details tab. change the property to Hardware Ids. I will copy the top id and search it to verify what device it is and what driver I need. That normally points me to the right driver in the support page or the search will put me on the path to the right direction. If you want paste that path in here or reach out to me and I can take a look as well.
@@GrayaOverload I click on driver details and it says “no driver files are required or have been loaded for this device”
On the details page, are you able to change that to the hardware ids?
@@GrayaOverload first one reads
PCI\VEN_14C3&DEV_0616&SUBSYS_061614C3&REV_00
@@GrayaOverload googled the first ID and I have a list to choose from but none are gigabyte
sorry fo all the questions but i finally built the pc and was wondering if there was a fan controller for the case fans for some reason they dont show on my fan control app for my cpu i have a good fan curve set for my gpu and cpu but my case fans are i think on max always they are very loud I have a LANCOOL 216 any help would be appreciated
I had a build recently in the lancool 216 airflow that didn't have a fan controller for case fans in the version I bought and I plugged them into the motherboard. They were all fine with fan speed. If you did buy the version with a fan controller and plugged them into it you probably have some other way to control it, buttons or software depending on the fan controller. I hope I helped.
I have the same case.
My fans aren’t load tho.
I’m having other issues, I can’t figure out if it’s the motherboard or cooling system.
Lian Li Case 216 v2
Lian Li ALC 360 Coolant System
Gigabyte B650 Gaming X AX Motherboard.
I have my pump connected to Fan3/System Pump.
I have the CPU_Fan Connected to the CPU_Fan Header on the motherboard.
Nothing in the CPU_Opt.
The Coolant Pump lights up, but the fans do not and they don’t move.
Inside the BIOS, it says N/A for the CPU_Pump and the CPU_Fans.
I have no idea what’s going on with this.
Everything else shows in the BIOS.
Building the same exact builds with parts today, and I see that my AGESA Ver is ComboAM5PI 1.1.0.1 rather than 1.1.0.2b. Will this effect anything and will I be able to change it in the future? If so, how would I go about that and is it important? Sorry i am noob, first time building pc
If you update you bios the agesa ver should update to the one that comes with the bios. I hope this helps.
Sorry for the slow reply this comment was held for review for some odd reason
Hello there - i got the same motherboard but not sure if i should update my bios my version is F2. A2 and B2 RAM slot is working for only 1 of my RAM but when i put that RAM on A1 and B1 its not working but my 2nd RAM doesn't work on all of them. I'm guessing Motherboard and RAM both bad?
Updating the bios should be fine. I don't quite follow. On just the A2 and B2, only one works if you switch the ram does the other slot work?
Looking for a good board for ryzen 7800x3d, 32gb 6000mhz cl30 ram and a 4080 super.
Is this the board to get or is there better boards for similar price?
I think this is a fine board for that setup. My friend had something close to this I built for him, and it works great. If you read thru all the comments some people did have issues, but they sound like doa board, which has happened to me many times over the years with different brands. I would recommend testing boards in the return window. Overall a good board. I wish I was able to go thru more boards, to have a more to compare to.
this mobo is very good. the most common reason for doa is a bad ram capacitor. happened to me so i just returned the mobo and got a replacement. no big issue. just inconvenient to swap out mobo's.
did you ever had issues with dram. i recently got this same mobo and ram and it will only post with one stick of ram. do you know anything to fix this issues?
@@olimpionunez4996 didn't. Try the other two slots to see if they post.
i am having the same issue any fix?
Спасибо 😉
your welcome
Is the BIOS different between this V2 and the original V1?
They look the same. You can't flash the v2 to v1 or v1 to v2.
I have 7900 with this mb. Do you think it can handle 7950x well either?
Yes.
We can't seem to get the Wifi to turn on. So we can't install our version of Windows 11 from USB. It requires a connection. Any way to turn wifi on prior to installing windows?
@@quirkylwj I don't think Windows has the driver for that card on the install yet. You could try the shift+f10 method to bypass. If that doesn't work you can use Rufus to remove that part of the install. I have used the shift+f10 and have a video on this. That would be the simplest and then install the drivers when windows is installed. There is a way as well to add the drivers to install and setup, depending on the effort you want to try. It is frustrating that MS cares so little for users it makes the setup hard to complete.
My pc just stay black no matter what. Is it because im using my ssd from the last board?
@@maliekjames6892 no, you should at least see the bios screen if it was the SSD issue. Do you have any red lights on the board.
Hello, how can I change the fan settings like yours? I can't click on that scale at the smart fan page. I dont understand why it is not allowing me to click on it to add and adjust the dots on the scale
When you are in Smart Fan Did you set the CPU_FAN Speed Control to Manual? Each Fan you click on should have that fan name instead of the CPU_FAN.
@@GrayaOverload Yeah, I figured out in the time. For some unknown reason it wont save the fan settings I do in the BIOS :/
That is no good. I would reach out to support or try a different bios version.
Im building this exact built after installing with just cpu ram and psu when i can apply my gpu? after enabling expo?
Whenever. Once I know thoes components work then I finish the build and then do bios tweaks like expo.
I juist build this but no post ! The red ddr light is on . Swtiched the memory chanels cleared cmos nothing working .
Have you tried just one stick?
@@GrayaOverload yes i had . also red ddr lights . cleared cmos again and did the q flash bios update . still red ddr . after hitting del key mutiply times system is up and running
@@vwduiven3072 I am glad you are up and running.
I don’t actually know HOW to download new drivers like WiFi so I can get a network connection. I have this same motherboard so I’m wondering where to find the needed drivers and every step to actually get my drivers update. I have been stuck on windows 11 set up and don’t know what to do to progress.
I have a video on how to get around the setup process without a network connection. th-cam.com/video/v-eK4wJRn78/w-d-xo.html
This happened to me, I was so frustrated but I was able to plug the PC into my phone for tethered hotspot but it used a insane amount of data😂
Quick update: Spoke to micro center and managed to get WiFi drivers installed. There were two different drivers: AMD WIFI driver and Realtek WiFi drivers (there was a 4 digit number attached to the “Realtek ____ WiFi driver” that I don’t quite remember right now).
(Quick notice: I followed a tutorial to do the windows 11 set up without WiFi which involved opening up commands and typing something in then selecting a many option at windows 11 network set up)
The issue when using a laptop to download the drivers to a flash drive was that I unzipped the folder with the driver before transferring it to my computer. That was why it did not install. So after getting the AMD WiFi driver instead of the Realtek WiFi driver, and properly installing it by unzipping and double clicking in the correct computer, everything started to work.
TL;DR: Bypassed windows 11 set up with a command
Used separate laptop to download “AMD WiFi driver” from gigabytes website list of drivers (Gigabyte Gaming X AX V2 M.B.)
Plugged the flash drive with the WiFi driver into new PC then unzipped + installed.
Installed the rest of my needed drivers after connecting to WiFi.
Does this mobo support win11 by default?
Yes
@@GrayaOverload thx bro
Hi, my xmp/expo profile is disabled and no profiles option, i have same motherboard/cpu as yours ... ddr5 auto booster is enough for this rams?
( CORSAIR VENGEANCE DDR5 RAM 32GB (2x16GB) 4800MHz CL40 Intel XMP iCUE Compatible Computer Memory )
That will be your only option. Is the memory running at 4800MHz?
@@GrayaOverload yh it is but it reaches 5000 automatically sometimes @GrayaOverload
should i keep the ddr5 auto booster auto or enabled ?
@@himurakenshin8054 try it, if you experience crashing turn it off.
How do you get the 6000 memory speed? I can’t seem to figure out for myself
Do you have xmp or expo profiles on your memory? What memory do you have?
@@GrayaOverload I figured it out, I had a 6000hz memory but when I clicked XMP it stayed at 4000 but I had to save and exit and boot up bios again for it to change that’s why I was so confused but thanks for reaching out
Can you help me with a boot issue… on this motherboard I plug in the jump drive with the windows 11 boot tool…the boot menu pops up but when I get to select drivers there are no drivers shown…even in the bios the flash drive does not pop up in the bootable devices… this is a brand new build
I can try. How did you set up the jump drive? If you see it in bios and it won't boot from it. Seems like the jump drive isn't set up to boot.
Can you do a video with this board with the best settings you think is good?
I will work on trying to get a video on that. This is my friends machine and I have to get him to bring the machine back over to record. Luckly, he lives closer to me then some of the other builds I have done.
Hello, now I have a problem, that when I turn on the PC I see abnormal ram consumption, I understand that it may be a failure in the RAM refresh. the board generates a short beep
I will need a bit more to go on. Is this once you are in windows you see the ran consumption? Or is the Ram Led error light red on the board?
@@GrayaOverload When I am already in Windows with the task manager I see a consumption of 10 to 15 GB of ram, with only the basic startup services, at this point I restart the computer and when I return to Windows I now see the normal startup consumption that It is 4 to 5 GB of ram... in Windows I do not have any red LED on the board
@@brayancamilo9247 thanks for that information. Sounds like a windows or a program install issue. When you see the high memory usage and open task manager the details tab you can select and then sort by memory. That should then give you the process that is using the memory.
@@GrayaOverload Thank you very much, it seems that the short beep when turning on the PC was a sign of a problem, I will review what you told me.
@@brayancamilo9247 I am suprised it has a speaker. A pattern of beeps is what I would be concerned about and not getting into windows.
Arigato, mate
Hello, how about I update from Version FB to FA2 but I still can't activate tpm 2.0 to be able to update to Windows 11, apart from that I don't know why two GPUs appear in my resource manager and one appears with PCI/VEN_100... do you know how I can activate the TPM?
To update bios Gigabyte does have some information on that but you can use their Windows tool @BIOS which is in the Gigabyte Control Center. You can also download the bios for your board put it on a USB and then use the flash tool in bios to update it. I don't know what you mean by Activate tpm. This board and the other video you posted this exact question on don't need to update bios for Windows 11 support, for other security fixes it probably will need a bios update. To see the TPM details open Windows Security, then click on Device Security, From there it will either have a security processor or say "Standard Hardware Security not supported". If you are on a different board that is older then you probably will need an update to get Windows 11 and default the tpm 2.0 to on. As far as the PCI/VEN_100 I would look at your device manager and make sure all devices have drivers. I would need to know more then just PCI/VEN_100.
@@GrayaOverload Thank you very much for the prompt response, I already updated the Bios to the FA2 version, an interface appears like in your video, I have Windows 10 Pro and I want to update to Windows 11, I get that TPM 2.0 must be compatible, I have not been able to activate it in the bios with FA2 version...
As for the device manager in the display adapter, I get PCI\VEN_1002&DEV_164E&SUBSYS_D0001458&REV_C6
I had not seen it before updating the Bios, my question is if it is normal
Did the TPM get enabled in Windows after the update? There is a ftpm that you should get enabled and that should then allow you to get Windows 11.
For device manager. That is an AMD Display device, Did you download the Radeon software? it might even be in Windows update in optional updates.
@@GrayaOverload in settings --> miscellaneous --> Trusted platform module I have the following options.
* Auto
*Disabled
*Enable dTPM
*Enable ASP fTPM
*Enable Pluton fTPM
I have enabled all the options and none of them always work for me in Windows it keeps telling me that I do not have TPM 2.0 active, maybe I'm incorrectly activating the tpm in the bios
For the AMD display device I have not downloaded the radeon software, do you recommend downloading it?
Did you try to apply defaults to the BIOS? When I have done a few machines that needed the bios update I reset to defaults.
Yes, I do especially if you play games.
when i enable the expo setting my ram doesn’t change from 4800. does it require a restart to take effect?
I don't remember exactly what the sequence is. What I do is set it and then save and reboot. Then I verify it is right.
Do you know how i can cap my ram speed? I bought a 6400 set and want to bring it down to 6000
You can do it manually if it doesn't have a expo or xmp profile. I would have to look at it again, it has been a bit since I tweaked it manually. I have had goo success with the profiles.
@@GrayaOverload i do have xmp enabled but it's running at 6400 and idk if its gonna cause stability issues with am5
@@IBaknam if it is running fine, I would go with it. If you do run into issues then remember what the memory is at go to stock to see if that is an issue. If it is then, that is when ibwiuld manually tune to 6000
I have the same exact specs but mine is stuck on 4800 mt/s instead of 6000 mt/s this happened after updating the bios. I've tried changing the xmp, expo profiles frequenzy and nothing works. anyone know how to fix this?
I have not seen this issue. It could be a bug in the bios. When you set expo/xmp that should activate the memory profile. You could reach out to gigabyte support.
@@GrayaOverload I reset everything and it worked thanks
Kinda wanted you to explain the options not just read them out
Might be another video, to explain all the options or a video on a few options. I will look at doing that. Just going thru bios takes a while let along explain. :) Thanks for the feedback.
Hello! I need some help, i just factory reseted my b650 and now i have fps drops from 240 to 80, any ideeas?
Is expo enabled?
The problem is, i dont have expo just xmp…
@@LixyAleks is xmp turned on?
@@GrayaOverload yes, just xmp
@@LixyAleks how are you cpu clocks when gaming? I am guessing temp are like other ryzen 7000.
How do i change the boot order. Whenever i get to boot menu and select my drive it doesn't start. But as soon i get into bios my drive usb drive isn't detected BUT it will try to start which it can't
Have you tried a different USB port or a different USB drive?
Hello,
How are the boot times on this motherboard/cpu combo?
First time can be long, next boot is normal.
@@GrayaOverload By normal what do mean? 10s, 20s ? I mean for me normal is around 12s or so
@@21Dimen I would say around the 12 sec as well.
@@GrayaOverload Okay, good.
I hope thats the case for me cause ill be getting the bundle from Micro Center with the 7800X3D
Have you had any other issues ?
No issues for my friend. He is enjoying it.
8:43 my Power on by keyboard is Off yet my keyboard can turn on the PC, anyone know How do I disable it?
I got a feeling it's because my keyboard is connected via the PS/2 port.
Also the RGB on my mouse stay on after shut down.
Anyone has solutions?
on ddr5 low latency suport its beter to enable?
It can, Depends on what you are doing. I test to see if there is a benefit.
how to enable amd fTPM??????
It should be enabled by default. Setting > AMD CBS > SOC Miscellaneous Control > Trusted Platform Module
is there an in-built Wifi system that I can enable?
@@bruktadesse9646 you will need to install the drivers to get it enabled. Make sure you use the right ones they have a few on the support website.
Anyone have trouble with the nvme not showing up at bootable devices ? I’m trying to install windows 11 and am unable to.
I did not.
Do i need to rename the bios file ?
Depends. If you flash in the bios no. If you are using the bios flashback then yes. The Bios flashback is where you put power to the motherboard and then press the button on the back of the mobo to flash it.
Ive been trying to enable tpm2.0 need help!!!
It should be enabled by default. Setting > AMD CBS > SOC miscellaneous control > Trusted platform module.
Where in this bios can I disable wifi?
No. but they should have it.
The bios is always stuttering with these 7k chips. I have the 7800x3D and I've never had a worse bios experience.. had a 3770k, 5930k, 9600k, 10400, 12600k, etc in various PCs..first time AMD and never had such a bad bios experience.
What do you mean stuttering? When you move the mouse or also when you use the keyboard?
@@GrayaOverload Mouse... Visually stuttering as his is, skipping around.
@@Vdhm91 do you have a different mouse to try. If you have different dpi setting it can produce this. I mostly use a keyboard. But I seen this on different bios from time to time. Depends on the mouse implementation in bios.
@@GrayaOverload I know it's the 7k chips. Another video I watched had made the same comment and a friend of mine has the same issue. We both just got our 7800x3Ds with this mobo.
@@Vdhm91 same motherboard maker?
I installed windows and can't get it to boot...
i have the same problem… did you ever figure out how to do it?
@@itami289 Faulty hardware
@@toutloffc1 How did you fix it exactly? I think I downloaded a corrupted file into the drive I put into my pc possibly damaging my ssd. Not too sure it’s my first pc.
Where do I do the online internet
Are you talking about wireless?
Yeah how is wifi possible with this thing ?
@@OFFICIALZAR422 you need to go to gigabyte support site and download the driver. You will need to make sure you have the right version and revision for the correct drivers.
@@GrayaOverload tried to install one but still no Wi-Fi appeared
@@OFFICIALZAR422 in device manager what shows at missing?
samsung memory ewwwww
This board sucks
why?
clueless
can you disable wifi and bt with this motherboard in the bios? Thanks
I don't think so. I would have to check again.