jeep liberty lower ball joints / upper control arms / wheel bearing (come along)
ฝัง
- เผยแพร่เมื่อ 10 พ.ค. 2021
- If a MECH A NIC video helped you consider donating to my patreon account to help support the channel. / the_mech_a_nic
or my paypal
paypal.me/jonathanrenteria1986
THE MECH A NIC’s amazon store ,here’s the tools I use
www.amazon.com/shop/themechanic
THE MECH A NIC’s Instagram page
/ the_mech_a_nic
THE MECH A NIC’s facebook page
/ the-mech-a-nic-1356996...
Thank you for watching my video, I appreciate the support ! - ยานยนต์และพาหนะ
![[LIVE] : ONE ลุมพินี 72 | คู่เอก "ก้องศึก vs โจอาคิม"](http://i.ytimg.com/vi/hT1EOSsRPac/mqdefault.jpg)
Great video. You are the first person to discuss the correct angle of the upper control arm. I wish I saw this before I starting my 2003 Jeep Liberty.
Recently had a rear assembly on a Camry that wouldn’t come off. Tried to get it to come off without taking knuckle off. Didn’t work. Took the time to get knuckle off and stood it up with wood blocks and used a sledge hammer head hand hammer and with 1 swing, that wheel bearing went flying across the yard about 8 yards. I thought I was going to break the aluminum knuckle but I didn’t care at that point. Aluminum and steel touching causes this corrosion.
Awesome video!fixin to rebuild the front end on an 06 Liberty!glad I found your video!
Thanks for watching
Nice idea with the digital angle meter/inclinometer 😊. As for giving it the Salsa 💃 that's stuck in my head now 😂.
Awesome Video! I appreciate all the detail you showed and the production quality. I even appreciated your humor and attitude. One comment on using the klinometer to set the angle on your upper control arm - There is nothing "wrong" with doing that but, there is a better way. You could have bumped the nuts up, like you did, so free movement is allowed and completed the rest of the installation. Then, put a floor jack under the C by the lower ball joint and raise it up until the weight of the vehicle was on the suspension before tightening up the nuts on the bushings. You could have even set it back on the ground before tightening the nuts. Again, your way is waaaaay better than what most folks do. Final tightening with full weight on the suspension is even more accurate.
I usually do the method of waiting till the car is on the ground to tighten everything but sometimes it's a pain to get to some of the nuts n bolts with the wheel on and the car on the ground
i think that angle tool is great the way u did it wiil work
Thank you 💪
Excellent tutorial, I will be changing the steering knuckle and associated components,
Tahnk you
Oktavious😊
Thanks for watching
"Bob's your auntie" 😂😂😂💀
giving it the beans is a very popular british saying. been in use for decades
Didn't know that. Thanks for the information
Dude, Just subbed to your channel good job on the video, loved the reference to "Give her the Beans" or in your case "give her the salsa" which works for weak salsa when it is not enough Beans. LOL, good commentary and reference to Eric O. at SMA love that guy's work.
Welcome to the channel 💪 . I'm still out here fighting the good fight and giving these cars the salsa 😁 . Eric O is 💯
That was a fun one to follow along, thanks for the effort!
You're welcome. Thanks for watching
Great job Jonathan! Love the slow mo ... and now I want salsa! 👍😂😂
Use your air chisel on the other side on the gap between the knuckle and the wheel bearing.
Definitely gonna start giving it the salsa
I'm doing the same project but with the tierods too. thanks for sharing
You're welcome. Thanks for watching
I like salsa, but prefer picante. Nice job on the repair. I'm preparing to do my own.
Lol 👍thanks for watching and good luck with your repair
Love the Salsa term. 👍👍
I’ve been watching Sarah N Tuned for many years and she would always say “ time to give it the beans “ . It was her Auntie who would say it when she was growing up and just adopted saying it 😉
Thanks for the info! Didn't know that 👍💪
yes she does
Nice work , you almost got some Salsa on your face with that setup ! And damn another car with a broken windshield, what the hellos going on over there ? You should call your show “Busted Cars County “
You started the Rona? LOL great vid tks
🤣👍thanks for watching
Don't worry your salsa is keeping us safe from the Rona virus. great video.
Thank you 👍
Good job! thank you for sharing
You're welcome. Thanks for watching
Give it the beans ! That's Sarah from Sarah in tuned. That's what she says when she road test cars.
Great video thank you!
Thanks for watching
Your neigbours must love you with all the air tool noise daily ! lol
Yeah....we're going to be moving soon. Hopefully get away from city area
@@themechanic6117 Smart move.. get a farm house. Lotsa room. Rent out the land.
Awesome job👍
Thank you 👍
Great commentary/explanation. Give it some Sauce
My friend I just ran across your video on the Jeep Liberty ball joints! Man, I tell you I sure wish you were in Connecticut I will sure come visit you do mine on my Liberty but great video thank you
Sorry but at least the video maybe helped you or it was entertaining
Wow! this guy is fast
Very helpful Thank You.
Thanks for watching
Ill be doing this this weekend. Well explain
Will it need an alignment after this?
Agreed, it felt so wrong cutting that sensor cable. I actually cringed lol.
Give it the Salsa 👍
👍😁
It might take a while but you can use an airtool grease gun to get those needle grease fittings
I like the new style of video good job as always 👍
Thank you for the tip and watching 💪
I have a 2004 jeep Liberty 3.7v6 Oil gasket leak. Is there away to just lift the motor up and get the oil pain out? Instead of removing the hole motor. If not. Will the oil leak eventually ruin my vehicle?
Givin' the salsa!!
Yes! 😁💪
My bolts keep spinning when I try to get the nuts on.. please help? I just got whole new ball joint knuckle and bearing all together and it won't stop spinning no matter the pressure applied..
Dale los frijoles.
😁🤣👍
Thanks so much for this video! I need both ball joints and upper control arms on each side of my '05 Liberty replaced. It is rear wheel drive only. About how many hours of Labor should the mechanic be charging me for? Thanks!
Great job jon plus attention to detail ! I love to watch the job your doing to show people what is involved in the job .. so now know we’re COVID-19 came from lol ..
😁👍 don't tell anyone lol
Give it the salsa !!!
Most definitely! 👍
Thanks alot u was stuck on the back bolt.... I gave it the salsas
"Giving it the Salsa." Love it!!!! Let's see if it reaches out here to the West Coast lol
"How I started CoronaVirus by doing this" LMAO!!! Had me rollin!!!!
Definitely a Hoot!! watching this, while I eat my lunch- It's 1:45pm
🤣🤣glad you enjoyed the video 😁💪
I'm not gonna lie! I'm having Ghetto Hooptie withdrawals. 😁
Plenty more crap to come in the future lol
I have some car work videos that I did. Also I subscribed my friend great video I have to do my lower ball joint’s today. This video helped a lot. What the name of that ball joint compress tool
Give it the salsa!
😁💪
Hey John, what's a good brand to choose from rock auto as far as suspension components?, what has given you the least amount of headaches/callbacks?, thanks in advance.
I stopped buying moog parts for the most part. Been buying mevotech and haven't had any issues. I only buy from the daily driver category or premium
@@themechanic6117 OK, thank you
@@themechanic6117 why did you stop buying moog?
I found moog balljoint or bushings fail just as quick as the less expensive stuff sold in the auto parts store. Why pay the extra money for moog then? Mevotech normally costs less and is pretty much the same quality. Of course I always recommend oem parts but most times people can't afford those parts
Did you put the hardware kit on? Or are the brakes going to chatter like they did before?
They're going to chatter for now. The guy is scheduled to come back next week to get the brakes done right 👍
give it the Sauce!
💪
Don't forget the "unga dungas."
Of course can't forget that lol
my lower balljoint snapped in half yesterday right as I was taking my exit off the highway, had to steer to a safe spot so the castle nut ground against the inside of the wheel for a bit and it's giving me hell getting it off. imagine ill have to cut it off.
Yeah, do what you have to
It all went smoothly after cutting off the nut. Thanke for the video.
WHAT YEAR IS THIS CAR??
Live your videos man, can you show use how to change a ground wire in a car??
Hey sir I'm in Texas is there a way I can get my jeep Liberty 06 3.7 l to you for repairs
Suspension repair
*FIRST* 🤟🏽
Nice!👍
It feels wrong to cut the wires because you have integrity.
Amen to that!!!
Where do you get that crc I cant find it anywhere
On ebay and Amazon. Depending on where you live it may not be available to you
@@themechanic6117 I've been looking at advanced auto and menards camt find it
You can only buy it online. I haven't found it in any stores
I think mole works better than salsa! 😂
😄👍
I started doing front lower control arms on my KJ and borrowed some bushing tools from AutoZone. Today I ended up making my own cups because NONE of them fit! The first one for the shock bottom I sacrificed a big HF impact socket. I had to make another from those crappy stock rock rails I had. I cut rings to the right length then cut slits in them welded them up to the right size then put another ring to make them about a quarter inch wall. The only thing I used was the press. I'll make two more for the lower control arm bushings tomorrow. What a pain. It's the only vehicle we have. 🙄 Where you at, bro?
Yeah that sounds like BS ! I'm in Valparaiso ,Indiana
@@themechanic6117 no bs. I'm in Orland Park, IL
I know where that's at, I lived most of my life in Chicago. Recently moved to Valparaiso
Get it the frijoles 👍
😁👍thanks for watching
Well, I’m of German descent, so, for me it’ll be “ giving it the oompah pah pah “.
Wait...was that the Midas jingle? Jon. Come on man.... when doing jingles GIVE IT THE SALSA!
I knew it was you who started corona virus
🤣🤣😏
If you're going to do one wheel bearing you do the other one too
In a perfect world sure. This is a customers car. They decide what gets done. If only one is bad then only one gets replaced
Give it the pinto beans?