Adding additional sockets to an existing ring final circuit
ฝัง
- เผยแพร่เมื่อ 28 ส.ค. 2021
- Adding additional socket outlets to an existing ring final circuit with horizontal cables runs where the existing wiring was not in the prescribed cable zones.
www.abcelectric.co.uk
NICEIC registered electricians in Altrincham, Greater Manchester
OZEV approved EV charge point installer
Addition of socket outlets and lighting points
Consumer unit swaps
Full/partial rewires
Garden lighting schemes
EICRs
Fault finding and repairs to fixed wiring
Domestic and commercial installations
#abcelectric
#electriciansinaltrincham
#extrasockets
#electricianlife
#sparky life
No tools were harmed in the making of this film.
sir great vide😊 thax
It’s nice to see Phil Collins is good with DIY as well as drums.
🤣🤣🤣
nice one bruv. would be nice to see more wiring rather than chasing out but helpful, thanks
Love the grinder attachment definitely speeds the cleaning up after. Yr right about taking pics just covers yr own arse. I’d prove it’s dead and left for future use good info and did have a chuckle you getting cramp in both legs I know that feeling
Hi I have just come across this video , and think you did a Nice job well done 👍. But I think you left the conductors a little bit too long. What I do is grab the conductors in hand in a fist and place the side of my fist flat against the edge of the box the snip the conductors against my thumb and that gives me the perfect length to dress in and enough slack for if the socket needs to be removed or replaced. Also I think you would off been better off using a rotary hammer drill with a chisel bit to cut the boxes in not a multi tool . Other than that nice bit of work mate . 👍
Nice work matey 👌🏼
Hi, how would you wire up your additional fused box to your garage with the existing main fused box. 😊
For the amount of money we have to pay councils under building control I would like them to hold the documentation on what is in the building. Then everyone should be sending up to date info and you’d cut down on the possibility of accidents. Never going to happen though.
Great intro! 😂
That attachment for the grinder looks good! Which vacuum do you use to extract?
The attachment is called MaxVac from Dust Arrest and I just use the ubiquitous Henry vac. Works a treat for what I need
@@abcelectric thanks mate, will look into that. Just what I need! Loving the channel, just found you!
Thanks Ben. You're welcome 👍
@@abcelectricHi mate
Does that attachment fit all angle grinders?
@@zippymo672 No. You have to select your grinder model
Don't you just love it when people are explaining the job but there's no volume ?
I didn't know there was a sound issue David. All was present and correct when it was proofed and uploaded. Thanks for letting me know and I'll review it
Just streamed it again from YT and I can't find any sound problems...
Try not to use jargon . " No grommet in the box " What does that mean ?
It's not jargon to anyone vaguely familiar with electrical installations. Look up the word grommet, but as a heads up it's basically a rubber washer. A box is a backbox - the box shaped thing that an accessory (socket, switch etc) screws to. This is not a "How to DIY your electrics" video. It's a Vlog of an electrician at work.
No offence but if your gonna try electrics and don't know what a grommet is I'd say get the professionals in
it means, get an electrician to do the work for you
You did not show how to chase the wall
Which part of marking walls with lines, running an angle grinder down them and knocking out the middle bit didn't you understand? That's chasing walls. Also, as per my previous reply to you about using "jargon", this is a Vlog channel about electrical work. It is not, and never will be, a channel showing DIYers how to do their own electrical installations. Unless you are fully conversant with BS7671 as a bare minimum and a qualified and certified electrician, attempting ANY electrical work is at best stupid, and at worst could result in fire, injury, death and/or a long stretch of incarceration.
Guve up the day hob and become a comedian, couldnt stop laughing at the cramp bit