@@elguapo5875 you can't just buy a "telephone cable"...it has to have the correct number of wires inside of it. The Epicenter uses four wires / contact leads. If it's not working I guarantee you bought the cheapest one you saw and it's TWO WIRE. 😂
I hope you ain’t got the wide and the sweep turnt open 🤦♂️for Banda you should want the wide at 3-6 o clock position and the sweep at 11-12 o clock depending on the tuning of your box and hint hint if you really wanna do something extra mess with the voltage or the chip in the epecenter
Hey just so you know for the wire ferrules they are 10gauge or smaller they sell a crimp tool just thought I'd let you know because I saw you didn't crimp any of your smaller gauge wire like the remote wire or the wire on the bass processor end.
In this case you still need the knob remote from the amp to the dash of the car or just the knob from the epicenter? Basically can you control the amp bass from the epicenter or do I need to set the 2 knob amp and epicenter?
Amp will need it’s own knob for volume for bass output, the epicenter knob is for adding extra bass. So in this case run 2 knobs one from the amp and other from epicenter. Amp knob being the main volume source. 👍🏼 hope this helps bro.
Thank you sir can you show me how you have your line out converted hooked up some people tells me to just connect the wire speakers no ground or power because the wire speakers create remote sensing signal can you confirm on this TIA
Yes you have 2 separate ones. I have the epicenter micro which has a 2 knobs built into it, the outside knob is for overall volume, the inside one is for epicenter effect
I have some 12’s kicker and some pioneer 10’s for my silverado which ones would u recommend for the epicenter? Its through a 1000watts amp is it gonna be bass-ey asf??
I had pioneers a while back in another vehicle and really didn’t like bass quality but I’ve always liked kicker they have a good punch to them also good on low notes. I’d run the kickers bro! 🤟🏼
why did you even add a fuse im so lost because of this im in the process of hooking up a soundxtreme st-ap6 and im doing all types of research and im finding other videos that say u dont even need a fuse so im a little lost in all this especially what size fuse i need bc i have kicker compc 12s daul box so idk what size fuse to get can some one help me
Better to add a fuse even if it’s not recommended, say processor is defective or goes bad only fuse that will pop is that one or cause from any other damage. I use a 5 amp fuse for something low voltage like that. Hope that helps boss 👍🏼
Hey man I got everything hookup but I can’t seem to know why my amp and epicenter don’t turn off when my car turns off. I also have a power switch installed in the front dash to be able to turn off and on the amp but for some reason doesn’t turn it off. Also notice that the epicenter and amp only turn on when I have the remote in and also touching the positive if I only have it In the remote control nothing turns on.. think you could help me out ?
@@lalogvlogs4344 i have a yukon xl on a aftermarket amp and i have a problem that the rear speakers dont play at all and i conected a new set of speakers to see if it was the speakers but i still had no sound out of the new ones i don’t really know what to do
I bought the same epicenter bro everything lights up but the knob won’t work so I don’t know what’s wrong with it I used a different wire for it and it still didn’t work
Just be careful with fuses if its too small it will blow and if its to big it will never blow and melt the wire make sure how much power the cable can handle and use the correct fuse for the wire (:
I never run crossover or epicenter into amp power will cause noise distortion and make amp pull more power away from the processor. Get a second battery or distribution block to get equal power all around and I make separate ground for every ground
True boss, i will be getting 2nd battery and doing the big 3 upgrade here soon. Videos will be on the channel once I do that! 🤟🏼 also will get a bigger amp for the new setup I got 👍🏼
I had mine connected to every amp i own and i never had any problems with them amp number one dd m3a second amp taramps md 8000 third amp taramps bass 8k and now i have the crescendo 5500 and i never had any problem
The silver sleeves? Those are wire ferrules to slide over wire so it’ll all stay together and prevent wire strands coming out and touching other wires. 😎
Excelente video el que hiciste, muy detallado la manera de manejar el cableado, solo me resta hacerte una pregunta mi estimadisimo Lalo, mi radio es un aftermarket y mi auto es una van con speakers atrás y adelante y una salida de subwoofer, de cual salida del radio debo conectar el epicentro para tener siempre los 4 speaker funcionando normal y el subwoofer correcte te dando el bass ya restaurado? O debo comprar algún aparato q me de salidas de audio extras para poder tener todos los speakers funcionando? De ante mano agradezco tu atención y a cualquiera q sea tu respuesta..
@@lalogvlogs4344 I want to get the audio control epicenter installed. I’m from NYC and the music installer here recommend me to install a cross over to fine tune all the system (mids and highs) and enhance my bass as well. When I play my paisa music some songs lack the bass and then other play perfectly fine. Do you have any experience with crossovers ? I’m looking to get the clarion mc360 which is the one they recommended. Not sure if the cross over is sufficient or if I still need the audio control epicenter.
@@lalogvlogs4344 it looked like I connected everything good not wrong so I’m tripping out but maybe like you said the wire might be the problem or I don’t know I just might buy another one
Hey bro thanks for the detailed video I really appreciate it. im new to car audio systems and I was wondering if you could please help me out. So my stock subwoofer blew recently on my truck and I wanted to replace it and upgrade the sub and amp. I did get a new head unit installed. I got the pioneer dmh 2660. I ended up going with the skar vd 8 d2 it's 400 watts rms and 600 peak watts. My boy let me borrow one of his amps the JL audio RD1000/1. I also bought the epicenter micro and 4 Gauge wire. Will this work? I don't know about the amp but I think it might be too powerful isn't it? I was also recommended by skar to wire the sub to 1 ohm and doing research on the JL amp it doesn't support 1 ohm only 2ohm's. I just started learning about subs, amps, ohms, watts, bass restorations, etc lol I feel like I've learned so much about it in the last 2 weeks but I want to make sure I'm doing it right and I won't blow my sub or my boys expensive amp lol thanks!
If you hispanic or listen to Latin music this is the only way to test with banda 😂 good job my dude I'm convinced 😁
That’s how it is bro! Saludos 🙏🏼
Super clean install!! Love how you did the knob
Appreciate it 🙏🏼😎
@@lalogvlogs4344 i bought a telephone cable the epicenter turns on but when I move the controll knob it wont work
@@elguapo5875 you can't just buy a "telephone cable"...it has to have the correct number of wires inside of it. The Epicenter uses four wires / contact leads. If it's not working I guarantee you bought the cheapest one you saw and it's TWO WIRE. 😂
Can you run bass processor with capacitor in system
@@lalogvlogs4344 can u run bass processor with capacitor in system ?
Thank you, this video is very good on the install of an epicenter controller, clean and right on, keep up the informative videos.
Good job bro that knob looks legit
Appreciate it bro 🤟🏼
Installation was super clean.
Good video bro learned something new
Thank you bro
So you used regular speaker wire for the power and ground right . Like I just get mine and split it and use it as if it was a power and ground
I remember those bird chirps from when I used to live in Dallas 🦅🤣
How did you set up your wide and sweep??
I hope you ain’t got the wide and the sweep turnt open 🤦♂️for Banda you should want the wide at 3-6 o clock position and the sweep at 11-12 o clock depending on the tuning of your box and hint hint if you really wanna do something extra mess with the voltage or the chip in the epecenter
Jesus thank you make it look easy cant wait to get one
Thank you. There's thousands of videos that explain but don't show the process very well. 5/5
Where did you get the ground a positive wires for the epicenter?
yo badasss video im gona tackle my install easy now after i figure out how to make that lil fuse tap holder deal shit is nicee
Yooooo that was hype💪🏾💯
Did you splice you remote turn on off from your amp in the epicenter
Can you use speaker wire for the wire power and ground
Hey just so you know for the wire ferrules they are 10gauge or smaller they sell a crimp tool just thought I'd let you know because I saw you didn't crimp any of your smaller gauge wire like the remote wire or the wire on the bass processor end.
So to add a 4channel amp you hook up rcas to the output on the amp then run rcas to the input on the 4 channel amp ?
Did you figure it out?
Is there a difference on why mine dont work i have a epicenter micro and i see u have the regular one
What size fuse did you use to replace the glass fuse?
3 or 5 amp will work!
Clean video
Is the little 3amp fuse connected only to the power wire?
Can’t wait till my dad gets this for the truck I bet it’s going to bump I think he going with a sound stream epicenter
For sure 🤟🏼
The bass sounds good. What’s the name of the song you bumping. I wanna play it on my system
How did you make the wireing for the epi center
Bro I’m trying to buy one but what setting did you adjust your epicenter ?
Bro were your power wire for dsp coming from??
aye bro, you mean to say the epicenter won’t work without the remote control knob? i didn’t connect it . and i don’t hear any restored bass .
How much better was the audio control epicenter from the other cheap one you had on your tahoe?
A major difference, nothing compares to the audiocontrol I def recommend it
@@lalogvlogs4344 ok really good to know, i was going to buy a blaupunkt 1600x but now knowing ill rather just spend the money for the epicenter
Sounds good
What do you have your wide and sweep set up at?
Will post a video within this week, going over the setup and I’ll make sure to record the epicenter adjustments 👍🏼
@@lalogvlogs4344 did you ever make that video? On the settings on the epic center did you leave them straight in the middle?
The Epicenter is the best 😮
Good stuff compa
How did u get the signal for the rca
Hey so i am using an lc2i to run on the factory radio but the base nob do i out in on the epicenter or on my amplifier right now it is on my amplifier
Good video👌🏽👌🏽 thanks 🔊
Nemesis bass processor the best 💪🏿💪🏿
Need to check one of those out, never got my hands on one yet
What if you listen to music that has bass already do you turn it all the way down ?
For the power and ground can I use 16gauge speaker wire?
you can, im personally running 4 gauge wires for power and ground to supply my amp
but i recommend running 8 gauge or smaller
Do u get bass with 90s rap still I don’t with knob turned down
Power accoustik is gas! I hit 144.5 on 2 gothics.
Would the kicker amp make a difference over the lets say a boss amp both at 1000 rms ? Been contemplating i have a boss lol
Yes it would be better to get a kicker amp more efficient an more power boss is entry level
An kicker is better in every way
So u actually need the same phone cable “ cable to work you can’t just use another amp cable or just another bass knob?
Clean video clean install... firme
Gracias mi carnal 🤟🏼🙏🏼
Buen video! Solo queria saber donde compras el tape negro? para amarar los cables por favor dejame saber gracias.
Gracias por el comentario compa, lo consigo por amazon se llama (tesa tape) ese tape es muy bueno. Espero que te ayude! 👍🏼
www.amazon.com/gp/aw/d/B00XPBB6L8?psc=1&ref=ppx_pop_mob_b_asin_title
Do you actually need a fuse for the epicenter ?
Is that 0 gauge power and ground cables for the amp?
Cool nice vid compa
Gracias carnal! 👍🏼
In this case you still need the knob remote from the amp to the dash of the car or just the knob from the epicenter? Basically can you control the amp bass from the epicenter or do I need to set the 2 knob amp and epicenter?
Amp will need it’s own knob for volume for bass output, the epicenter knob is for adding extra bass. So in this case run 2 knobs one from the amp and other from epicenter. Amp knob being the main volume source. 👍🏼 hope this helps bro.
Thank you sir can you show me how you have your line out converted hooked up some people tells me to just connect the wire speakers no ground or power because the wire speakers create remote sensing signal can you confirm on this TIA
Yes most definitely, stay posted I’ll make a new video this weekend showing my setup and wiring! 👍🏼
Awesome video!! I'm going to get a epicenter as well!!👍
Wait so then what about the amp bass knob? Are you going to have two bass knobs one from the epicenter and from the amp?
Thats a good question?? 🤔🤔
Yes you have 2 separate ones. I have the epicenter micro which has a 2 knobs built into it, the outside knob is for overall volume, the inside one is for epicenter effect
What are those small connectors on the ground remote and power called
wire ferrules
Controlas el bajo con el knob del Amplificador de bajo o con el Knob del epicenter o tines que usar ambos?
Ambos, usas el knob normal de tu amplificador, y si quieres bass del epicenter usas ese knob
Did u move da voltage jumpers inside da unit if so wat u set em at i hav mine at 2.5
It depends on the amp you run with it. Google your amp for input sensitivity and try to get as close as you can.
I have some 12’s kicker and some pioneer 10’s for my silverado which ones would u recommend for the epicenter? Its through a 1000watts amp is it gonna be bass-ey asf??
I had pioneers a while back in another vehicle and really didn’t like bass quality but I’ve always liked kicker they have a good punch to them also good on low notes. I’d run the kickers bro! 🤟🏼
@@lalogvlogs4344 thanks man will try it out👌🏽👌🏽
@@lalogvlogs4344 used the best JWJ6 uuju
why did you even add a fuse im so lost because of this im in the process of hooking up a soundxtreme st-ap6 and im doing all types of research and im finding other videos that say u dont even need a fuse so im a little lost in all this especially what size fuse i need bc i have kicker compc 12s daul box so idk what size fuse to get can some one help me
Better to add a fuse even if it’s not recommended, say processor is defective or goes bad only fuse that will pop is that one or cause from any other damage. I use a 5 amp fuse for something low voltage like that. Hope that helps boss 👍🏼
Where's the link on how you made the wire harness
Hey man I got everything hookup but I can’t seem to know why my amp and epicenter don’t turn off when my car turns off. I also have a power switch installed in the front dash to be able to turn off and on the amp but for some reason doesn’t turn it off. Also notice that the epicenter and amp only turn on when I have the remote in and also touching the positive if I only have it In the remote control nothing turns on.. think you could help me out ?
You’re remote turn on Is the Probelm. Do you have an after market or a stock stereo..?
How did you tune it
Maan I'd like to hear that in person.
It must sound sick.
Question does LC7i audio control works the same as the Epicenter? I bought the wrong thinking it was an epicenter
No, does not work the same bro! 👍🏼
Thanks
Did you have to tune your epicenter
Yes tune to your liking, you will have to keep messing with it until you get it right 🔊
Does the Epicenter work as a Line out converter
No you would have to either get an lc2i or lc7i from same brand audio control, this is only to maximize and restore bass 🤟🏼
Do you have a link to the video of the harness you built? Looks great !
Hey man i listen to cumbias a corridos the usual for us mexicans 🤣 but what are your wide and sweep settings on your epicenter
I got it low bro, like at 1/4 on both. I had it at 3/4 but it was distorted bad 🤣 but do 1/4 of a turn on both bro. 🤙🏼
I have a soundstream but ordered a audio control hopefully its a lot better
You’ll notice a major difference bro! 🤟🏼
@@lalogvlogs4344 i have a yukon xl on a aftermarket amp and i have a problem that the rear speakers dont play at all and i conected a new set of speakers to see if it was the speakers but i still had no sound out of the new ones i don’t really know what to do
Check door boots bro, could have a broken wire
What gauge size wire did you use for that little harness you made bro?
14 gauge bro primary wire copper 🤙🏼
@@lalogvlogs4344it doesn’t matter that your remote turn on is the same gauge?
Can I install the epicenter wire to the head unit instead of the amp?
You can especially the remote and outputs
Good job bro
I bought the same epicenter bro everything lights up but the knob won’t work so I don’t know what’s wrong with it I used a different wire for it and it still didn’t work
Could be a bent tab on the epicenter or knob itself where the phone line connects into or also defective epicenter bro.
@@lalogvlogs4344 appreciate it bro
Hell yeah , good video bro 🙏
Where’d you connect the rca’s
Into the amplifier probably si only the subs get the epicenter effect
Great video !
I have a question im new in this audio stuff
Can I use a 10a fuse instead of the 3a fuse that you used on the 12+
Should work good bro! 🤙🏼
Just be careful with fuses if its too small it will blow and if its to big it will never blow and melt the wire make sure how much power the cable can handle and use the correct fuse for the wire (:
@@eddyvilla4057 thanks I’ll make my research
Las bocinas las conectaste normal o en mono?
Thats bad ass
I never run crossover or epicenter into amp power will cause noise distortion and make amp pull more power away from the processor. Get a second battery or distribution block to get equal power all around and I make separate ground for every ground
True boss, i will be getting 2nd battery and doing the big 3 upgrade here soon. Videos will be on the channel once I do that! 🤟🏼 also will get a bigger amp for the new setup I got 👍🏼
I had mine connected to every amp i own and i never had any problems with them amp number one dd m3a second amp taramps md 8000 third amp taramps bass 8k and now i have the crescendo 5500 and i never had any problem
what are those plugs you used for the epicenter ?
The silver sleeves? Those are wire ferrules to slide over wire so it’ll all stay together and prevent wire strands coming out and touching other wires. 😎
Where can we buy them.
Amazon bro
Thanks Lalo, clean work!!!
Thanks bro! 🤟🏼
Yo primo how did you do the remote and gound n power cable I been looking on how you did it I went to your channel and couldn’t find 1:39
Depends on how your own amp and Epi are placed
Sounds good clean bass what's your setup ??💯🇮🇹
Thanks bro, I got rid of my tahoe sadly a week ago. But my setup was 2 Sundowns SAs V2 in a probox. Never had the chance to record em in the truck
Excelente video el que hiciste, muy detallado la manera de manejar el cableado, solo me resta hacerte una pregunta mi estimadisimo Lalo, mi radio es un aftermarket y mi auto es una van con speakers atrás y adelante y una salida de subwoofer, de cual salida del radio debo conectar el epicentro para tener siempre los 4 speaker funcionando normal y el subwoofer correcte te dando el bass ya restaurado? O debo comprar algún aparato q me de salidas de audio extras para poder tener todos los speakers funcionando? De ante mano agradezco tu atención y a cualquiera q sea tu respuesta..
Si pudo ayar jose Antonio como conectar el epicenter
If i have a 4 channel processor do i still need a epicenter?
Epicenter is to maximize bass or restore on songs that don’t have any bass 👍🏼
@@lalogvlogs4344 ok thanks
Where did you get that sure kit
Good video compa. Where did you buy your wire at ?
The epicenter wiring I made my self with scrap wire bro and the power and ground I got amp kit at best buy 4 guage ofc 🤟🏼
@@lalogvlogs4344 thank you bro 🙏🏼
@@lalogvlogs4344 was it 18 gauge wire that you used for the epicenter ?
Yes and I added a better fuse holder to it bro
I got one but the light on the knob is orange what inhave wrong? Help
All the wires in spot where need to be?
where did u get ur power ground and remote cables?
For the epicenter?
@@lalogvlogs4344 yes
@@lalogvlogs4344 the red black and blue or do they come with the epicenter?
I made them myself 👍🏼
@@lalogvlogs4344 what type of wires tho?
Clran install! Have you made the video of how you made the wiring harness?
Appreciate it bro! I have little clips of it on my phone but never made a full video on it lol
@@lalogvlogs4344 where did you get the fuse holder with the led..I've been looking them up on Amazon but can't find it.
I got it at Walmart a couple of years back bro, in the automotive section
@@lalogvlogs4344 make the video and upload it bro or at least the little clips ???
Did you have to get the LC2i as well or nah?
No bro, had a basic line output converter
Does the bass sound distorted with the epicenter?
I have a soundstream on another vehicle bro and the audio control is waaaaay far better in sound quality. Never distorts bro highly recommend 👍🏼
@@lalogvlogs4344 I want to get the audio control epicenter installed. I’m from NYC and the music installer here recommend me to install a cross over to fine tune all the system (mids and highs) and enhance my bass as well. When I play my paisa music some songs lack the bass and then other play perfectly fine. Do you have any experience with crossovers ? I’m looking to get the clarion mc360 which is the one they recommended. Not sure if the cross over is sufficient or if I still need the audio control epicenter.
Do I need to re adjust amp gain after installing a epicenter?
No, just tune epicenter sweep and wide to your liking 👍🏼
@@lalogvlogs4344 oh cause I just put mine in my Hardbody and shit rattles more then the bass I can hear 😂 guess it's working lol
How can I add an epicenter if i have an lc2?
The same RCA that's coming out of the LC2 you'll put into the bass processor and from the bass processor into the amp inputs.
Will this blow my speakers sub or amp?
If amp or processor not set or tuned right, yes it could mess something up. But I’ve never had problems with any of my audio
I connected my epicenter and it doesn’t throw the bass out of the subs I connected the amp and double din rca to epicenter and no bass, why???
Could be wrong bass knob cable or knob bro ?
@@lalogvlogs4344 I had a epicenter lost the knob then bought the same brand bass knob so I figured it would work
@@lalogvlogs4344 it looked like I connected everything good not wrong so I’m tripping out but maybe like you said the wire might be the problem or I don’t know I just might buy another one
@@lalogvlogs4344 or do you think if I put and equalizer would I still need an epicenter or it’ll be better to put both for better sound for the subs
Hey bro thanks for the detailed video I really appreciate it. im new to car audio systems and I was wondering if you could please help me out. So my stock subwoofer blew recently on my truck and I wanted to replace it and upgrade the sub and amp. I did get a new head unit installed. I got the pioneer dmh 2660. I ended up going with the skar vd 8 d2 it's 400 watts rms and 600 peak watts. My boy let me borrow one of his amps the JL audio RD1000/1. I also bought the epicenter micro and 4 Gauge wire. Will this work? I don't know about the amp but I think it might be too powerful isn't it? I was also recommended by skar to wire the sub to 1 ohm and doing research on the JL amp it doesn't support 1 ohm only 2ohm's. I just started learning about subs, amps, ohms, watts, bass restorations, etc lol I feel like I've learned so much about it in the last 2 weeks but I want to make sure I'm doing it right and I won't blow my sub or my boys expensive amp lol thanks!
Do i use both remotes, the amp and the one to the epicenter?
Yes
I'm about to install mine bro. Doesn't the epicenter really make a difference?
Huge difference brotha! 🤙🏼
Looks like the bass sounds great but where the how to install video
What size fuse do you put on the epicenter
4 amp bro
Tuning video?
Where the video for the fuse that u created
i`ll get one :)