I love how even when you found the hardened filament, you didn’t stop there and you showed other possible problematic pieces for others to see what to do (like the direct drive gears)
Thank you so so much! My ender 3 se v3 had a very bad case of it clogging after I ran out of filiment and it got stuck there. I tried everything and looked everywhere for tutorials. I couldn’t find a single one.. Until I found this one which is the best tutorial I have ever seen, it’s at perfect pace, goes over every detail and everything you should watch out for. Tells you what to do incase certain stuff were to happen or if you need a slightly different solution. You have all my thanks.
@@KakiDIY No problem, it helped alot although very unfortunately my printer broke again lol. It was leaking this black, glassy like substance that was plastic like in texture that was so hot it melted through the print bed. Sorry to ask but do you have a video on leaky filaments or that anyone else has one? Just wondering but thanks a lot for the tutorial as I helped me finish my build.
My v3 SE has gotten into the habit of clogging at the end of every print. I use mainly PLA, and the clog turns up in the same place as you've shown in this video. What I do to unclog is preheat TPU, use a candle to heat up the tip of the cleaning rod and push it in and through the clog, then burn off the residue that sticks to the rod. Repeat about twice more until I can't feel anything impeding the movement of the rod and all is well and I can print again. My problem now is just the fact that it clogs after EVERY print.
excellent instructions, i haven't had a clog yet since 8 months of ownership but this is a great resource to have on hand should the problem eventually arise. thanks.
Thank You for your comments. You must have given lots of care and attention to the printer and feeding it good quality filaments... thanks for watching !
Thankyou this totally worked - was a bit nervous unscrewing all those screws lol - and praying you reversed it at the end so I could put it all back together again - but got the clog out and now its working perfect again.. It has given me the courage to now try on my 2 x flashforge ones lol
I just bought the Elder 3 V3 SE after installing the printer. I tried to get the plate level. I got the printer to touch the plate, and after a few minutes, it threw an error that said the nozzle temperature was too low. Then it gives me a loud noise. Do you have a solution for this or a tutorial on how to fix it?
I have an ender 3 v3 se, and Ive been looking all over online but Can’t find anywhere what type of metal the filament drive gears in the extruder are? I wanted to run carbon fiber PETG but have heard you need to make sure your gears aren’t brass. I have a steel nozzle for it already also.. Would you happen to know if they are brass gears? Thank you very much!
Don't think they are brass.. just normal metal. The hotest I ran was 260 degrees for polycarbonate.. and normal PETG.. the drive gears worked fine for both.. probably adjust the drive gear tensioner... should be OK
Just put back the tube. It is a heat break PTFE tubing that is from the dame diameter as a Bowden tube. If you lost it, just get a bowden tube like Capricorn, cut it to length and replace it.
Hi, i follow your instructions, the clogged filament solved. But after connect the cable motor, i tried move the extruder but it doesn't work or rotate. I panicked so i buy new motor and tried connect it with the motherboard, doest work either.. i got panicked again..
@KakiDIY I figured out I had plugged the fa s in the wrong way so the heat sync fan was the cooling fan so the filiment was getting warn inside the hot end softening and then clogging haha
I love how even when you found the hardened filament, you didn’t stop there and you showed other possible problematic pieces for others to see what to do (like the direct drive gears)
Total respect for this man. He showed us every possible solution for blockage filament!
Thank you so so much! My ender 3 se v3 had a very bad case of it clogging after I ran out of filiment and it got stuck there. I tried everything and looked everywhere for tutorials. I couldn’t find a single one..
Until I found this one which is the best tutorial I have ever seen, it’s at perfect pace, goes over every detail and everything you should watch out for. Tells you what to do incase certain stuff were to happen or if you need a slightly different solution.
You have all my thanks.
Glad it helped! Thank You very much for the kind comment and feedback.
@@KakiDIY No problem, it helped alot although very unfortunately my printer broke again lol. It was leaking this black, glassy like substance that was plastic like in texture that was so hot it melted through the print bed. Sorry to ask but do you have a video on leaky filaments or that anyone else has one? Just wondering but thanks a lot for the tutorial as I helped me finish my build.
thank you so much!, it works!, my printer is alive again 😁
Thank you so much for this video. It helped a lot. Appreciate you.
My v3 SE has gotten into the habit of clogging at the end of every print. I use mainly PLA, and the clog turns up in the same place as you've shown in this video. What I do to unclog is preheat TPU, use a candle to heat up the tip of the cleaning rod and push it in and through the clog, then burn off the residue that sticks to the rod. Repeat about twice more until I can't feel anything impeding the movement of the rod and all is well and I can print again. My problem now is just the fact that it clogs after EVERY print.
Good tip.. Thanks !
I have almost the same problem, mine clog after every filament chance, as soon as try retraction
excellent instructions, i haven't had a clog yet since 8 months of ownership but this is a great resource to have on hand should the problem eventually arise. thanks.
Thank You for your comments. You must have given lots of care and attention to the printer and feeding it good quality filaments... thanks for watching !
thanks a lot! Really useful!
Bro u saved my work im New and well now im working
Thank you VERY much!!!
This helped A LOT. I was able to unclog my printer and fix it :)
Thank you, you helped me a lot with this video, I didn't know what to do to unclog the pipe
You save me!!, thanksss from chile my friend!!!
Thank you for this. You save us.
excelente video bro, i solved the same problem
I needed a step by step guide to disassemble it, the filament got stuck between the gears, thank you very much
Yes thankyou, this is the correct answer for my Ender 3 V3 SE! #ender3VESE.
Hi my friend i from Brazil you help me a lot thanks i liked your vídeo.
Thankyou this totally worked - was a bit nervous unscrewing all those screws lol - and praying you reversed it at the end so I could put it all back together again - but got the clog out and now its working perfect again.. It has given me the courage to now try on my 2 x flashforge ones lol
Great work! And yeah, way too many screws to our liking. But it is doing it's job to make the printer look nice.
Thank you for sharing 🙂
You helped me a Lot once, Now my SE clog after every time I go for retraction to change filaments... Anyone ever heard about it? Thank you
You are a good man.
Thabks'to you a just fix my machine tonight, really useful video 👌❤️
Got my printer up and running in no time
Thank you!!! It worked!!!
Are we supposed to take of the hot glue on the connector
And if the extruder gear teeth are swept? Can only those gears be changed or do I need to buy a complete extruder?
My extruder moto pin is glued too, how do I change it so ?
what kind of screws does the heatsinks fan use?
I just bought the Elder 3 V3 SE after installing the printer. I tried to get the plate level. I got the printer to touch the plate, and after a few minutes, it threw an error that said the nozzle temperature was too low. Then it gives me a loud noise.
Do you have a solution for this or a tutorial on how to fix it?
Just had to change my hot end, on my 3 v3 SE
Please, what should be the length of the PTFE tube? Thank you
Mine measured at 4.5 cm for longer tube connecting to the extruder. The small tube for the heartbreak I measured at 1.9 cm.*
Thank You!!
I have an ender 3 v3 se, and Ive been looking all over online but Can’t find anywhere what type of metal the filament drive gears in the extruder are? I wanted to run carbon fiber PETG but have heard you need to make sure your gears aren’t brass. I have a steel nozzle for it already also.. Would you happen to know if they are brass gears? Thank you very much!
Don't think they are brass.. just normal metal.
The hotest I ran was 260 degrees for polycarbonate.. and normal PETG.. the drive gears worked fine for both.. probably adjust the drive gear tensioner... should be OK
They appear to be steel not brass, possibly a hardened steel but they're certainly more durable than brass
I have a small tube that fell when I changed the nozzle, what can I do?
Just put back the tube. It is a heat break PTFE tubing that is from the dame diameter as a Bowden tube. If you lost it, just get a bowden tube like Capricorn, cut it to length and replace it.
thank you sooo much! you saved me and tons of my nerves :))))
Thanks, u video was very usefull!!
Glad to hear that! Thank You
Man its impossible to remove nozzle head. its not turning like yours. What will i do now? its looking damaged now.
Ohuh... I find it easier to remove when the hot end is heated up. Heat it up to 250.. and try it ?
@@KakiDIY yea i tried to remove without heating first but it was already damaged when i heat it. I just bought new hot end.
My printer has a horrible jam, no matter how hard I push with nozzle cleaner, the jammed piece does not come out, :c I don't know what else to do.
Hi, i follow your instructions, the clogged filament solved. But after connect the cable motor, i tried move the extruder but it doesn't work or rotate. I panicked so i buy new motor and tried connect it with the motherboard, doest work either.. i got panicked again..
Do i have to unplug or plug again? Or do i need to make sure the motor is hot? Pleeasee i need solution
And what if it clogs up Every time you print! It does about 5 layers into a raft and then boom clogged
Try to chdck filament temperature.. or change another filament?
@KakiDIY I figured out I had plugged the fa s in the wrong way so the heat sync fan was the cooling fan so the filiment was getting warn inside the hot end softening and then clogging haha
Some idiot put some kind of glue on the cables that connect the cr touch and hot end…
Yeah that's standard for Creality. Just use some needle nose pliers. Comes off pretty easy.
@@dailyprofitcenterAh, thanks for the tip mate! I’ll be sure to try that next time I open my printer up.
Same with this one. We left it untouch ..
@@KakiDIY Yeah, I saw that in your video after I rewatched it.
No wander you clogged the hot end. Try using the filaments that Creality recommend Noob.
He's trying to help people? Jesus get a life
Hey, may I ask you a question about the Ender 3 v3 se?
Yes whats up?