Electric Scooter Hub Wheel Brushless Motor:bit.ly/2YXDUnc Find More Items Here:bit.ly/2Pd1qY8 $9.9 Daily Deals:bit.ly/2SZI7D7 Download Banggood APP to get extra 10%OFF:bit.ly/2uUZ4GS
What is this nonsense? 'Turn the line?' What is the 3-speed? What is the wiring for the 3-speed? Explain the 'learning line'. What does the anti-theft' do? what do you connect it to? what do you connect the single cruise line to? What is it typically used for? What is 'high brake'? How do you use that connection? How is it different to 'low brake', and why would you use one rather than the other? This is useless 'cha-bu duo'.
im using two 5200 mah 40c 11.1 lipos in series to control this, but the motor needs a slight push before it starts spinning, got the same results when i tried powering it with a 35 v psu,any idea why i need to nudge the wheel abit for it to start spinning?
Do you think the motor will be okay if i disconnected of the motor lines? I testet it without having it on the ground and the speed at the start was 30km and then dropping down and not usually 23 and dropping to 20km because of the speed limit for el scooters in my country which is hardwired in the motherboard. It would be nice if i could benefit from that extra boost at the start. The internet says some motors will be fine im unsure if this will damage it or nit
i havr ebike with hadlebar light horn and 3 speed buttons , and i need to replace it but i will replace aslo the controller so where i should connect those wires of hadlebar?
Can we connect these drivers to the pc and use them to increase the power or speed of the scooter? Or what can I do to increase the speed of the scooter? I have an 800+800 1600w scooter.
Are you still active? I need to install a larger hub motor on my Daymak Vienna 84 V scooter. I'm wondering if l can just splice new hub to OEM scooter harness
Love this video!! Just wanted to ask you where did you buy the standard to support the wheel (around 3:32 and further)? Or did you build it? I really need one of those. thx.
@Peter Hicks what do you mean by speed control? Is it the speed limiter ? I've got a aovo pro and it has a white wire inside going to the controller. I'm wondering what it is ?
In your videos at about 2 minutes and 46 seconds where you connect the three motor phase wires ? The yellow green and blue wires ? What is the name of those connectors? I have a new controller with those same connections. But my bike has different connectors. So please please help me ? Maybe you have a link on Amazon where I could get them? I need both ends. Male and female with the casings. Please and thankyou.
Hi Maker Tutor. its always nice to watch your videos with a lot of amazing projects, thanks. I am not cleaver onto electronics but I just have some hobbies. I want to make my first mini bike using water from my old hoverboard and controller. The problem I notices is when I put up the speed the motor slowing down and the speed control displace also switch off. Could you please help on this case? Thanks in advance🙂
Hello. I bought an Yume M11 electric scooter. The scooter came with the rear light broken (the red diffuser ) and because was mounted on the rear fender after a while broke completely. Yume sent me a replacement but now I have no brake light. I changed the connectors between them and the led's are working either 2 either 3 from 5 total which 3 I presume should be for the brake light. I understood that the controller has a low and a high brake wire. Is the high 12V? I will mount a separate brake light but I see other connectors with only 1 wire. It means the wire is only +? If yes which one. And the ground is common with other ground wire? Please help me. [Smile]
2:35 it shows. But if you have a battery like me that has a key On/Off you can just connect the thin red wire to the fat Red positive + wire and use the battery normally as your on off
Hello my name is Paulo chapel, friend help me with a brushed controller d 30 vts 500w 28 A. of the brand XUN. I don't know how to connect this device, on the accelerator with a contact key, this accelerator has 5 wires (On Throttle Socket: Green, Black and Red) (separator: 2 wires; Yellow and blue.) This throttle has a motorcycle key and battery indicator. on the brush controller there is a white socket written: (Derailleur) in the colors green red and preto. I already know it's the accelerator but what about the two yellow and blue wires???? where can i plug it in?? we have two blue wires in a white socket written lock two blue wires written lock; what are these two wires for?
My wiring is a mess. The new controller doesn't match the connections of the old controller so how can I know what wires need to go where, there are blues, pinks, purples...not so simple
@@yannicktseyen5411 yes!! I had to change the connections so they matched. If you go to my channel i have a video talking about it. Maybe it'll help. But just get some wire strippers and a crimper and you can change the ends. And dude, i knew nothing about wiring and this kind of stuff, complete beginner, so I'm sure you'll get it soon.
Boss pa help Naman po kc ung motor Kong ilalagay sa isang motor mgkaiba Ng controller motor kong ilalagay my 5 hall sensor pero ung controller wala boss panu Kaya to boss please 🥺
Open the controller box pull it out find a small smashed staple looking thing on ur circuit board most all will have it.at least 1.solder that about half way,front the start of one side to the middle..put a good thick coat of solder.close it up reconnect it and you'll be amazed.also if u have a 3 speed twitch connector one wire will be neutral.take a volt meter and find the 2 hots.1 will not be.DO NOT CONNECT THE 2 HOT.CONNECT 1 WIRE WITH THE NEUTRAL.SEE HOW FAST IT GOES.DISCONNECT DO THE SE WITH THE OTHER.KEEP THE 2 THAT PRODUCE THE MOST SPEED CONNECTED.THATS HOW U REACH THE TOP SPEED OF URVSCOOTER WITJPUT SPENSING AANY MONEY AND EVEN IF U DO SPEND MONEY YOUR NEVER GPNNA GET MORE SPEED AND TORQUE THAN DOING THESE 2 FREE THINGS.
What are you chatting??It does. The Original scooter use hall sensors in their twist grip and thumb throttles so knowing how to wire a pot to the excelerator wires on a standard brushless controller helps
Electric Scooter Hub Wheel Brushless Motor:bit.ly/2YXDUnc
Find More Items Here:bit.ly/2Pd1qY8
$9.9 Daily Deals:bit.ly/2SZI7D7
Download Banggood APP to get extra 10%OFF:bit.ly/2uUZ4GS
Really like the tip with the pot. Good way to test before put everything back together 😊👍🇮🇪
What is this nonsense? 'Turn the line?' What is the 3-speed? What is the wiring for the 3-speed? Explain the 'learning line'. What does the anti-theft' do? what do you connect it to? what do you connect the single cruise line to? What is it typically used for? What is 'high brake'? How do you use that connection? How is it different to 'low brake', and why would you use one rather than the other? This is useless 'cha-bu duo'.
Yes im wondering about the 3 speed also..
Can it make the scooter faster or slower?
@@the_keeponbuilding I’m pretty sure it’s to have three speeds to select form
@@lanejohnston350 wel i found the answer the same day.
Its 20% slower or default or 20% faster.
How would i go about hooking up the M5 display to this? The OEM display has 5 wires going to controller.
Have a controller and I can't power it on can you help me out plz
im using two 5200 mah 40c 11.1 lipos in series to control this, but the motor needs a slight push before it starts spinning, got the same results when i tried powering it with a 35 v psu,any idea why i need to nudge the wheel abit for it to start spinning?
I need those green connectors for the 3 yellow blue and green Phase wires. Do you have a link preferably Amazon link or.. ?
Do you think the motor will be okay if i disconnected of the motor lines? I testet it without having it on the ground and the speed at the start was 30km and then dropping down and not usually 23 and dropping to 20km because of the speed limit for el scooters in my country which is hardwired in the motherboard. It would be nice if i could benefit from that extra boost at the start. The internet says some motors will be fine im unsure if this will damage it or nit
Forget it. The motor gets shaky so i wont have it disconnected
i havr ebike with hadlebar light horn and 3 speed buttons , and i need to replace it but i will replace aslo the controller so where i should connect those wires of hadlebar?
I've just bought one of these would I be able to wire this to an mi 366
Hello! i have a question how do i connect this tipe of controller to a TF100 (Comon acelerator with lcd with 5-6 pin)
Will this way work as my dash don't work so can't turn scooter on but had it riding yesterday after fixed it now the screen doesn't turn on
Can we connect these drivers to the pc and use them to increase the power or speed of the scooter? Or what can I do to increase the speed of the scooter? I have an 800+800 1600w scooter.
Thank you. Thank you very much for presenting it so clearly.
Are you still active? I need to install a larger hub motor on my Daymak Vienna 84 V scooter. I'm wondering if l can just splice new hub to OEM scooter harness
Thank you wery much, this helped me so much
Yo i have the brushless motor controler 48v and 250w, motor 48v 250w so max speed on e bike is 36kmh what to do on the controller to go faster
Can we use this just as a general multipurpose power supply please reply.
It is okay to combined the brushless and brushed controller?
Works perfectly👌💥
please which cable wires for display and which display i can use here , thank you
Love this video!! Just wanted to ask you where did you buy the standard to support the wheel (around 3:32 and further)? Or did you build it? I really need one of those. thx.
Where does the 3-wire kickstand sensor switch connect to the controller?
my controller only has 1 red positive wire instead of the 2 posiitve (one big one small). how do I connect a power switch with only 1 positive wire?
What do you mean by turn the line
Could you go over the Kugoo S1 plus wires
what is turn the line?
@Peter Hicks what do you mean by speed control? Is it the speed limiter ? I've got a aovo pro and it has a white wire inside going to the controller. I'm wondering what it is ?
@Peter Hicks cheers
Hi do you know where i can found a GEMINI CONTROLLER by ORDOO 72v 100A ?
In your videos at about 2 minutes and 46 seconds where you connect the three motor phase wires ? The yellow green and blue wires ? What is the name of those connectors? I have a new controller with those same connections. But my bike has different connectors. So please please help me ? Maybe you have a link on Amazon where I could get them? I need both ends. Male and female with the casings. Please and thankyou.
Can you please show me how to make my scooter go without a throttle an it's a 24 volt chain driving please 🙏 help in Tacoma Washington
what is turn the line for. stand for what is this for lights or another line.if its so. where to put or use that turn line
I think turn in line is throttle.
Nice thank you ineed this very helpful
Hi boss you have a video tutorial of brushless dc motor dual controller 48v 25a 120....
Thanks for advance...
Hi Maker Tutor. its always nice to watch your videos with a lot of amazing projects, thanks. I am not cleaver onto electronics but I just have some hobbies. I want to make my first mini bike using water from my old hoverboard and controller. The problem I notices is when I put up the speed the motor slowing down and the speed control displace also switch off. Could you please help on this case? Thanks in advance🙂
I removed the potentiometer from a brushed motor controller, to use with brushless.
Can it work
Hello. I bought an Yume M11 electric scooter. The scooter came with the rear light broken (the red diffuser ) and because was mounted on the rear fender after a while broke completely. Yume sent me a replacement but now I have no brake light. I changed the connectors between them and the led's are working either 2 either 3 from 5 total which 3 I presume should be for the brake light. I understood that the controller has a low and a high brake wire. Is the high 12V? I will mount a separate brake light but I see other connectors with only 1 wire. It means the wire is only +? If yes which one. And the ground is common with other ground wire? Please help me. [Smile]
How Is the connection for the ON/OF controller switch??
He briefly shows a diagram. You just connect the switch between the two red wires on the battery connector
2:35 it shows. But if you have a battery like me that has a key On/Off you can just connect the thin red wire to the fat Red positive + wire and use the battery normally as your on off
Hello my name is Paulo chapel, friend help me with a brushed controller d 30 vts 500w 28 A. of the brand XUN.
I don't know how to connect this device, on the accelerator with a contact key, this accelerator has 5 wires
(On Throttle Socket: Green, Black and Red)
(separator: 2 wires; Yellow and blue.) This throttle has a motorcycle key and battery indicator.
on the brush controller there is a white socket written: (Derailleur) in the colors green red and preto. I already know it's the accelerator but what about the two yellow and blue wires????
where can i plug it in?? we have two blue wires in a white socket written lock two blue wires written lock; what are these two wires for?
Hi, how do i connect the gps tracker black and red wires to the controller for power ?
10K ! Thank you very much.
Hello, I have a problem with the brakes
If I put the High Brake Line on +, the engine just shuts off, but it doesn't brake.
Can somebody help me?
Hello bandgood teem please help me my scooter ti30 display LCD error Speed regulator installation error whats problem solved
Thanks for letting me know how to connect these. Wire
So do i need to buy Sensor BL DC motor instead of Senseless motor ?
looks like a kid could do this considering the plugs and wire colours match up !!
Instrumentation green wire what for ?
Hi , i have a project in mind and i think you can help me. Please reply
Something is wrong with mine, the 10K pot does not make it go
me too, nothing happen .. but motor can run on self learning mode. i use sensorless bldc.
Perfect 👍
please corcuit controller for ninebot AB01
Brilliant, thank you :)
My wiring is a mess. The new controller doesn't match the connections of the old controller so how can I know what wires need to go where, there are blues, pinks, purples...not so simple
Hey man did you manage to fix it ? I ended up in the same situation....
@@yannicktseyen5411 yes!! I had to change the connections so they matched. If you go to my channel i have a video talking about it. Maybe it'll help. But just get some wire strippers and a crimper and you can change the ends. And dude, i knew nothing about wiring and this kind of stuff, complete beginner, so I'm sure you'll get it soon.
how to connect to throtelle
Boss pa help Naman po kc ung motor Kong ilalagay sa isang motor mgkaiba Ng controller motor kong ilalagay my 5 hall sensor pero ung controller wala boss panu Kaya to boss please 🥺
Thanks 😊👍🙏💯
Schematic diagram please
Liked this video al lot, and being curious where could I buy the stand you are using for mounting the wheel/motor.
Please could explain what does it mean 3 Phase wires? Phase is something related to AC current but we have DC brushless motor.
The controller turns the DC voltage to AC at the motor.
Open the controller box pull it out find a small smashed staple looking thing on ur circuit board most all will have it.at least 1.solder that about half way,front the start of one side to the middle..put a good thick coat of solder.close it up reconnect it and you'll be amazed.also if u have a 3 speed twitch connector one wire will be neutral.take a volt meter and find the 2 hots.1 will not be.DO NOT CONNECT THE 2 HOT.CONNECT 1 WIRE WITH THE NEUTRAL.SEE HOW FAST IT GOES.DISCONNECT DO THE SE WITH THE OTHER.KEEP THE 2 THAT PRODUCE THE MOST SPEED CONNECTED.THATS HOW U REACH THE TOP SPEED OF URVSCOOTER WITJPUT SPENSING AANY MONEY AND EVEN IF U DO SPEND MONEY YOUR NEVER GPNNA GET MORE SPEED AND TORQUE THAN DOING THESE 2 FREE THINGS.
How to make it faster ????
need eabs regen braking.
Goodday! I'm having issue with my scooter.. it suddenly lost its speed. Before it can run 40kph, but now only 35kph. What would be the cause?
It may be Battery Degradation. After a lot of discharge cycles the output gets weaker and weaker
U got fatter haha. I dont mean that, i couldnt help it lol
@@ademworthwent1168 haha! Lol!
People Even the slowest of slow got time to catch up to thease instructions ..lmao I'm very impatient
THXXXXXXXXXX
I swear to an e scooter it's connected to the controller and all you have to do is unplug one wire for more speed...?
Top
👍👍👍👍👍👍👍👍👍👍👍
Op
dislike wy you dont show wiring together?????????
😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂👊
quite a bad video not really how to connect them up
This seems pretty useless.
Salui
This does not teach anything, he basically disconnected his own scooter wires and reconnected them. :S
What are you chatting??It does. The Original scooter use hall sensors in their twist grip and thumb throttles so knowing how to wire a pot to the excelerator wires on a standard brushless controller helps
yessssssssssssssssssssssssssssssssssssssss