4 Ways to CLOSE Snapback Watch Case. NO SPECIAL TOOLS

แชร์
ฝัง
  • เผยแพร่เมื่อ 22 ธ.ค. 2024

ความคิดเห็น • 499

  • @Striker50_
    @Striker50_  ปีที่แล้ว +11

    Watch items & tools on my affiliate Amazon Storefront: www.amazon.com/shop/striker50/list/21OF83UT7HHQ0?ref_=cm_sw_r_cp_ud_aipsflist_aipsfstriker50_48VGWA0GKKRJBAQZWHPQ

    • @benomae9890
      @benomae9890 4 หลายเดือนก่อน +1

      Am gonna subscribe and double subscribe.

    • @Striker50_
      @Striker50_  4 หลายเดือนก่อน

      @@benomae9890 Glad to hear thanks! 🙏💯

  • @leetatum66
    @leetatum66 8 หลายเดือนก่อน +29

    Thanks so much! I thought I was so clever, buying an $8 watch repair kit & learning how to replace batteries. But then with half the watches, I couldn't get the backs back on! I watched your video & used a wooden jewelry case to apply pressure. It worked like a charm! Thanks so much for your virtual help :)

    • @Striker50_
      @Striker50_  8 หลายเดือนก่อน +2

      Nice! And the kit is absolutely useful. Closing snapbacks is definitely tricky however. Glad this helped!

  • @jonathanlloyd2306
    @jonathanlloyd2306 ปีที่แล้ว +102

    I use the hammer too, but slightly differently. I position the case back in perfect alignment with the gasket in place. I place the watch face down on a firm surface with a soft cloth. Then in one continuous swing I hit the case back with similar force to driving a six inch nail into wood. Unfortunately I have had to buy a new watch.

    • @Striker50_
      @Striker50_  ปีที่แล้ว +3

      yikes!

    • @georgemcconnell5405
      @georgemcconnell5405 11 หลายเดือนก่อน +9

      Lol I did that exact same thing after 4 hours of messing with an Armitron. I just didn't care at that point. Shattered the glass to bits and the back still didn't go on.

    • @sueparnell3818
      @sueparnell3818 10 หลายเดือนก่อน

      😂😂😂

    • @wafiyiffat7770
      @wafiyiffat7770 9 หลายเดือนก่อน

      Lol hahahahah

    • @thisisnotrandy
      @thisisnotrandy 2 หลายเดือนก่อน

      I put a piece of wood on the case back and hit it with a hammer and it simply worked. I utilized a somewhat restrained version of the swing you're describing lol.

  • @anns354
    @anns354 8 หลายเดือนก่อน +5

    Thanks for the tip!. Used a rolling pin. Took a few goes to get the back aligned just right - but less than 5 minutes. Saved a trip to the jeweller!

    • @Striker50_
      @Striker50_  8 หลายเดือนก่อน +1

      Nice! Nice to hear that a rolling pin works thanks for sharing

    • @copytan2395
      @copytan2395 8 หลายเดือนก่อน +3

      Same here, took out my nice watch for an upcoming wedding, changed the battery, rolling pin for the win (barz). B)

    • @sophia-marieyoung6773
      @sophia-marieyoung6773 2 หลายเดือนก่อน

      Same! I tried a hardback book but it wasn't stiff enough. Then a screwdriver but it had a hexagon shaped handle that wasn't working. So then a rolling pin!
      Thanks for the video, sir! Subscribed!

  • @SteveKay-m2o
    @SteveKay-m2o 11 หลายเดือนก่อน +15

    The level did the trick for me. It was so satisfying to hear that snap. Thanks very much!

    • @Striker50_
      @Striker50_  11 หลายเดือนก่อน

      Yes! It's almost like a Snapple drink but in reverse ◀️

  • @ykostudio
    @ykostudio 11 หลายเดือนก่อน +4

    Thank you for posting this video! I had to take the back off my Timex, last night, and couldn't get it on. After I watched your video, I improvised a tool for this purpose and got the job done. No reassuring click with my watch, but the back is securely in place and that's what counts. So EASY, I should have thought of this!
    Jon

    • @Striker50_
      @Striker50_  11 หลายเดือนก่อน +2

      Glad to hear a success story! I backed out the first time out of precaution, but figured out it requires force and poppppp went right in

    • @redstickham6394
      @redstickham6394 8 หลายเดือนก่อน +1

      I didn't get the click either with my Junghans Mega Aluminum, but when I examined the watch, it looked like it was sealed all the way around. I guess the click isn't as loud with some watches than it is with others.

    • @Striker50_
      @Striker50_  8 หลายเดือนก่อน

      @@redstickham6394 Yup my Tissot doesn't seal with a snap either. It's pretty quiet

  • @Patrick-ge2zn
    @Patrick-ge2zn ปีที่แล้ว +11

    Changed a few batteries in my time and the hardest think to do is refit a press on back . Last time used the end of a rolling pin , exactly the same diameter of the watch , worked a treat .

    • @Striker50_
      @Striker50_  ปีที่แล้ว +2

      Nice! The more household items that we know work the better!

  • @B27-o2c
    @B27-o2c 10 หลายเดือนก่อน +6

    I wish I had found this video earlier today. It would have saved me a lot of frustration. Thank you.

    • @Striker50_
      @Striker50_  10 หลายเดือนก่อน

      I went through the struggle myself you're not alone 🤘

  • @DanielaMaria1998
    @DanielaMaria1998 9 หลายเดือนก่อน +6

    Cannot believe I dropped my new (second hand) watch the second I got it 😭 the back jumped off and i was heartbroken thinking i had ruined it, this video is a life saver❤ i used a very small hard back notebook and it worked great.

    • @Striker50_
      @Striker50_  9 หลายเดือนก่อน +1

      LAWD Jesus!! Thank goodness you were able to put humpty dumpty back together again

  • @Bro-Lando
    @Bro-Lando หลายเดือนก่อน +1

    Great vid! Was able to pop the backing off from previous experiences but had sooooo much trouble getting it back on. This along w/ the comments helped me think outside the box. Ended up using a Tide liquid detergent bottle cap that was the same size as the backing and it worked after just a couple of tries! I spent hours messing w/this before finding your vid!

    • @Striker50_
      @Striker50_  หลายเดือนก่อน

      @@Bro-Lando Wowww never heard of that working glad to hear it!!

  • @rjstackadolla1214
    @rjstackadolla1214 9 หลายเดือนก่อน +4

    Dude I spent all night tryna take apart my watch, clean it, and put it back together. Somehow I lost a diamond on the face which now I have to find someone to replace and it took me an hour to get the backing on. Appreciate the video I used everything around me and finally found a hammer and got it 💯🙏 those are harder to pop on than you would think

    • @Striker50_
      @Striker50_  9 หลายเดือนก่อน +1

      Exactlyyyy. The first time I tried I couldn't close it and left it like that for months until I finally really looked into it

  • @RexyChirp
    @RexyChirp 2 หลายเดือนก่อน +1

    You just saved me a whirl to a watch store! I couldn’t figure out how to put the back on and this video worked perfectly!

    • @Striker50_
      @Striker50_  2 หลายเดือนก่อน

      @@RexyChirp Nice!! Glad this helped

  • @brettb8825
    @brettb8825 11 หลายเดือนก่อน +3

    Thank you for posting this. In my haste, I didn't protect the back and scratched the heck out of it using the hammer method which didn't work. The book spine, however, worked perfectly.

    • @Striker50_
      @Striker50_  11 หลายเดือนก่อน

      Glad you found it useful! Thankfully it's the back and not the face, etc. At worst, you could get a polish that buffs out blemishes, or take it in to get polished professionally.

  • @Becky33333
    @Becky33333 หลายเดือนก่อน +1

    My God thank you. I gave up trying to close my sons watch a year ago. Your video was soooo helpful. The level worked 😊

    • @Striker50_
      @Striker50_  หลายเดือนก่อน

      @@Becky33333 Nice! You didn't give up, you just took a break 😀

  • @KWayneization
    @KWayneization 9 หลายเดือนก่อน +3

    Was having a hard time with other viewed methods. Your book method worked the first time. Thanks

    • @Striker50_
      @Striker50_  9 หลายเดือนก่อน

      Awesome I'm glad to hear it worked
      Cheers to another motorcycle rider

  • @deltabasshunter8974
    @deltabasshunter8974 8 หลายเดือนก่อน +2

    Thank you so much. Your video helped me put the back on my wife's watch. I used the leveler and didn't even have remove the band. Cheers!

    • @Striker50_
      @Striker50_  8 หลายเดือนก่อน

      Nice! Sounds quicker than me for sure

  • @scottoftheroad
    @scottoftheroad 11 หลายเดือนก่อน +12

    Thanks! I had troubles getting a back onto a watch and was scared to use anything more than my thumbs to apply pressure. Your video upped my bravery and it finally snapped on.

    • @Striker50_
      @Striker50_  11 หลายเดือนก่อน +2

      Nice! I was the same way at first and was too scared to break it

  • @redstickham6394
    @redstickham6394 8 หลายเดือนก่อน +2

    Thanks for this video. I have a Junghans Mega Aluminum atomic watch I've had for around 20 years and always paid someone to change the battery for me. The last time I need to change the battery the shop I go to couldn't do it because the jeweler was out so I did it myself. I thought the back was on but I dropped the watch and the back went flying and I couldn't get it back on. After watching this video twice, I went in the tool box and the level was the first thing I saw so I tried that, along with a mousepad and glasses cleaning cloth, and I think it worked. The watch looks like it is sealed all the way around, but I didn't hear a click or any sound like that. I did this on a kitchen table the dishwasher was running in the back ground so it's possible I may not have heard it. Thanks so much for showing us how to do this!

    • @Striker50_
      @Striker50_  8 หลายเดือนก่อน +1

      Nice! That's how I learned how to fix mine too. Mr. Lin was my watch guy for years but he started getting old and his business wasn't open anymore so I learned to do it myself. My Tissot doesn't make a noise when I seal it so all of them don't make a snap noise. As long as you see the cap fully seated you should be good

    • @redstickham6394
      @redstickham6394 8 หลายเดือนก่อน +1

      @@Striker50_ Thank you for clarifying that. I was worried because it didn't make a noise but since it looks like it's sealed, it will probably be fine. I've replaced the band twice on this watch and that was pretty easy. I plan to hang on to it as long as possible since it's a great looking watch and keeps good time since it sets itself to the atomic clock. I'd like to get a Citizen Eco Atomic one day, but the price is out of my range.

    • @Striker50_
      @Striker50_  8 หลายเดือนก่อน +1

      @@redstickham6394 Take care of that baby and no worries, you already got a great time piece so take care of that one

  • @GoatMeal365
    @GoatMeal365 3 หลายเดือนก่อน +1

    Awesome video, I watched other videos on how to replace my Daniel Wellington watch. Most of them have no voice or explanation, so I couldn’t get the back, back on. With tour vid, I got it back on in less than a minute. Thanks!

    • @Striker50_
      @Striker50_  3 หลายเดือนก่อน

      Less than a minute is incredibly impressive! Hats off to you

  • @donitahopke758
    @donitahopke758 4 หลายเดือนก่อน +3

    I didn't spend much time trying to figure out how to get the back of my Timex watch back on. After about five minutes, I went to TH-cam for advise. That is where I found you! I didn't have any of the tools you suggested handy but I did have a small piece of wood about eight inches long (2x4) that worked perfect. Thanks for the video!

    • @Striker50_
      @Striker50_  4 หลายเดือนก่อน

      @@donitahopke758 nice! I'm thrilled to hear I was able to be a resource 🤙👋

  • @DavidLivingston01
    @DavidLivingston01 9 หลายเดือนก่อน +1

    Thanks for the video. I used the book method, and it worked! Before I found your video, I was going to use a 1" socket and lightly tap it with a hammer, but was worried that I would scratch the back plate.

    • @Striker50_
      @Striker50_  9 หลายเดือนก่อน

      OOOOO good thing you found my vid and glad to hear it helped!
      Vibration is not good for watches bc it could throw off the hands and internal components

  • @iliaten
    @iliaten 6 หลายเดือนก่อน +1

    BLESS YOU MAN!! After hours of fooling around, clucked it in 5 minutes following your clip!

    • @Striker50_
      @Striker50_  6 หลายเดือนก่อน

      Let's gooooo

  • @hotdog1214
    @hotdog1214 7 หลายเดือนก่อน +1

    You sir are a lifesaver. Wouldn't have thought of these methods, seemed too scary and brutal but it worked first time!

    • @Striker50_
      @Striker50_  7 หลายเดือนก่อน +1

      That's awesome! People have been saying that rolling pins work too

  • @Ponimaju
    @Ponimaju 9 หลายเดือนก่อน +2

    Great vid, the tip to use a mousepad really helped a lot.
    The watch I was working on was a huge pain in the ass - the most important part ended up being to use something as flat as possible and as close to the size of the watch back as I could get - a level or a thinner piece of wood didn't work for me at all, but a piece of wood with roughly the same width as the watch-back diameter worked the first time. It seems like the consistent even pressure was more important than being able to put more force/weight behind it.

    • @Striker50_
      @Striker50_  9 หลายเดือนก่อน +2

      Yup! Originally when I tried this I literally almost stood on it and it still wouldn't close. Someone else mentioned a flat piece of wood worked for them which is great to have another option. So much easier when it's flat

  • @amazingdancingmonkey
    @amazingdancingmonkey ปีที่แล้ว +3

    Thanks so much! I tried the hammer method and it didn’t work, but the book method did! Appreciate the help.

    • @Striker50_
      @Striker50_  ปีที่แล้ว

      Thanks for sharing what worked for you!

  • @billshinas27
    @billshinas27 2 หลายเดือนก่อน +1

    Great video, my issue is I have an Axis watch, and the back cover has no notch to pull up, so I'm guessing it screws off, what's a great way, thank you.

    • @Striker50_
      @Striker50_  2 หลายเดือนก่อน

      Hmm send me a link or model number so i can see what youre referring to

  • @kvog85
    @kvog85 4 หลายเดือนก่อน +1

    This was really helpful, thank you! I ended up using the edge of a couple cutting boards and I FINALLY got it back on!

    • @Striker50_
      @Striker50_  4 หลายเดือนก่อน +1

      @@kvog85 incredibly creative 👌

  • @gleboleinik6436
    @gleboleinik6436 หลายเดือนก่อน +1

    As someone who knows little about watches and thought I'd have to take my recently purchased automatic watch to the shop for an expensive fix: thank you brother

    • @Striker50_
      @Striker50_  หลายเดือนก่อน

      @@gleboleinik6436 Glad to hear this helped my friend 🤘

  • @ogmarke
    @ogmarke 5 หลายเดือนก่อน +1

    Best sounding click ever… thanks man your tricks got me on the right path to success!

    • @Striker50_
      @Striker50_  5 หลายเดือนก่อน

      @@ogmarke You did it 🤙💪

  • @sportsmemories481
    @sportsmemories481 9 หลายเดือนก่อน +2

    Thank you, I appreciate the knowledge. This video saved me from more hair pulling out. Appreciate it greatly

    • @Striker50_
      @Striker50_  9 หลายเดือนก่อน

      Glad to know it helped 💥🤘

  • @AdamMayor
    @AdamMayor 3 วันที่ผ่านมา +1

    Just what I needed. I ended up using a decorative wood block / sign that we had laying around. First try successful - thanks!

    • @Striker50_
      @Striker50_  2 วันที่ผ่านมา

      @@AdamMayor 🤌🤌🤌🤌👏

  • @zc5181
    @zc5181 26 วันที่ผ่านมา +1

    I was very frustrated with closing the case back when I passed by your video, Hammer worked for me and I used a résistance band on the watche's glass for it's protection

    • @Striker50_
      @Striker50_  26 วันที่ผ่านมา

      @@zc5181 Nice! Glad to hear that worked

  • @shawnflemingmusic
    @shawnflemingmusic 5 หลายเดือนก่อน +1

    Thank you! Messed around with mine for so long and the book trick worked instantly

    • @Striker50_
      @Striker50_  5 หลายเดือนก่อน

      @@shawnflemingmusic Glad one of the options worked! The first time I tried I thought I was going to break it so I didn't close it for months

  • @Beefy-Cheese
    @Beefy-Cheese 10 หลายเดือนก่อน +2

    My watch from the 90s doesn't specifically say its waterproof, but if it's s that hard to close is it waterproof anyway?

    • @Striker50_
      @Striker50_  10 หลายเดือนก่อน +1

      A lot of watches are water resistant more than waterproof. The rubber seal you see on some of them helps, but some may not have it. I was kind of surprised when I learned about ATM water ratings for watches. But 99% of people will never go swimming more than 3 feet underwater

  • @victorvonderkrausse5492
    @victorvonderkrausse5492 10 หลายเดือนก่อน +2

    Hi man, I JUST closed my Lorus watch by hitting it with the hummer ! I v e tried all your method, but no results so I was forced to hit with a hummer witch finally close a square Lorus watch !
    I have also issues with an old Q&Q, I definitively can t open the watch , it is like glued !
    The watch is not expensive, but is very good I have changed the battery just once in 6 years, and now it has stopped working !
    I have a few tools, I just cant open it ! Do you have any advice please !!??

    • @Striker50_
      @Striker50_  10 หลายเดือนก่อน

      That's great to hear! My square watch in this video was also so difficult to close and I gave up originally before finding out it needs a lot of pressure.
      Absolutely, sounds like the rubber seal could have gotten sticky, or it has suction which is making it very hard to open.
      Do you have the little pry tool that I used to open the watch? It makes it very easy. Another option would be to go to a local watch place and see if they can open it for you. I had a local place here that I would go to when I didnt know anything at all and he would only charge me $5 per battery replacement

  • @bttrfly_wngz09
    @bttrfly_wngz09 8 หลายเดือนก่อน +2

    Used a hardcover book, and it worked perfectly!! Thank you so much!

    • @Striker50_
      @Striker50_  8 หลายเดือนก่อน

      📚📚📚📚

  • @mrs_angry4261
    @mrs_angry4261 2 หลายเดือนก่อน +2

    Thank you for the video, I still couldn’t get the back to click in. What solved it for me was following the tip mentioned somewhere in the comments below but I can’t find it again. It was to use a bit of sticky tape to hold the back in place before you apply pressure with your weapon of choice. If you can’t apply the pressure evenly the back just rocks to one side. Once I’d taped it in place and applied pressure it went in at the first attempt. No satisfying click sadly but it is definitely on - no black to be seen.

    • @Striker50_
      @Striker50_  2 หลายเดือนก่อน

      @@mrs_angry4261 The tape is helpful to know I'll be sure to share that with people struggling!

  • @renepoche4171
    @renepoche4171 9 หลายเดือนก่อน +2

    Thanks for the tips! I tried these and finally got it with the hammer!!

    • @Striker50_
      @Striker50_  9 หลายเดือนก่อน

      Yes!!! That's incredible!

  • @MrJKellerLewis
    @MrJKellerLewis 7 หลายเดือนก่อน +1

    I tried the book but it would slide so I used the book as the surface and had a piece of 2x2 that worked great to seat it. Great advice! I was worried I would break it but this showed me not to be too concerned

    • @Striker50_
      @Striker50_  7 หลายเดือนก่อน

      2x2! First time someone has mentioned that, I'll add it to the list 📝

  • @billbronander6237
    @billbronander6237 11 หลายเดือนก่อน +2

    First I took a drop of 3-1 oil on my finger to slightly lubricate the rubber ring. After I used a rachet socket slightly smaller that the watch back and hand pressed it on. Worked like a charm without having to remove the watch band.

    • @Striker50_
      @Striker50_  11 หลายเดือนก่อน

      Interesting take, sometimes opening the watch band is an inconvenient step on some bands. And thanks for mentioning the oil. Lubrication is always important, I am always learning

  • @blessingsara11
    @blessingsara11 8 หลายเดือนก่อน +2

    Did this and it worked!!! Glass broke (was a cheap one anyway) but it worked 🤣 I'm not worried tho cos it can be fixed. Next time will take it to the expert since beginning 4 sure ❣️👍🏻

    • @Striker50_
      @Striker50_  8 หลายเดือนก่อน +1

      Awe bummer, shouldn't crack but budget watches can be a little more fragile

    • @blessingsara11
      @blessingsara11 8 หลายเดือนก่อน +1

      @@Striker50_ yes, I just really like that watch but it's nothing high end, but now since it broke I will put a sapphire one & will never try to change a pressure watch by myself

    • @Striker50_
      @Striker50_  8 หลายเดือนก่อน +1

      @@blessingsara11 sapphire is niceee

  • @Edyth_Hedd
    @Edyth_Hedd 6 หลายเดือนก่อน +1

    Just used your book technique and it worked perfectly. Thank you!

    • @Striker50_
      @Striker50_  6 หลายเดือนก่อน

      That's incredible.🙏 Didn't think this video would help so many people

    • @Edyth_Hedd
      @Edyth_Hedd 6 หลายเดือนก่อน +1

      @@Striker50_ We had dropped off a bunch of watches at a jewelry store to have the batteries replaced, and the store said they couldn't get the back to snap on one of them (SO lame), so I found your video and fixed it myself. I never realized how much force it takes to re-affix the back on some watches, and this one made a nice, satisfying "SNAP."

    • @Striker50_
      @Striker50_  6 หลายเดือนก่อน

      @@Edyth_Hedd Yes! They're pressurizee essentially.
      I honestly gave up for a few months the first time I tried because it wouldn't go on

  • @mariadillon860
    @mariadillon860 7 หลายเดือนก่อน +2

    Thank you for making this video - the ideas are excellent😀 However, none of them worked on my Nordgreen watch - every time I got one side down the other side popped up. I will have to take it to a jewellers - which is a shame ☹️

    • @Striker50_
      @Striker50_  7 หลายเดือนก่อน +2

      Sometimes I wish I could try
      That's how the rectangle watch was the first time I tried. I left it like that for months because I was scared of breaking it

    • @mariadillon860
      @mariadillon860 6 หลายเดือนก่อน +2

      I used quite a bit of force - the winder got severed. So I will now need to get it repaired or buy a new one (can I just add, that was entirely my own fault and nothing to do with your suggestions)😊

    • @Striker50_
      @Striker50_  6 หลายเดือนก่อน +2

      @@mariadillon860 You're too graceful, my apologies for any inconvenience
      Thank you for sharing the caution to take

  • @HoroHigh369
    @HoroHigh369 9 หลายเดือนก่อน +1

    OMG you just saved me $20- used the hammer! You are awesome. Thanks for sharing!!!!

    • @Striker50_
      @Striker50_  9 หลายเดือนก่อน +1

      I love hearing the success stories. Thanks for taking the time to share!

  • @deanattard
    @deanattard 2 หลายเดือนก่อน +1

    Will this keep the watch waterproof say upto 100mm

    • @Striker50_
      @Striker50_  2 หลายเดือนก่อน

      @@deanattard Closing the case back should not change the original rating of water durability. This is not an enhancement to the design of the watch.
      Hope that helps

  • @pascaleelliott63
    @pascaleelliott63 หลายเดือนก่อน +1

    I have an issue I was hoping you could help me with. While trying to pop the back piece back into place, the rubber band snapped in half. So now the back won't pop on without it. What's the best thing I do, here? Can I buy another rubber ring for the back of the watch, or does it need to be replaced all together now? Help me 😭

    • @Striker50_
      @Striker50_  หลายเดือนก่อน +1

      @@pascaleelliott63 I would suggest your local watch repair store, they have a lot of random parts sitting around

    • @pascaleelliott63
      @pascaleelliott63 หลายเดือนก่อน +1

      @@Striker50_ Ok thankyou :)

    • @Striker50_
      @Striker50_  หลายเดือนก่อน

      @pascaleelliott63 Absolutely let me know how it goes

  • @ernestshu
    @ernestshu หลายเดือนก่อน +1

    Thanks. Could not find a suitable hardbook and my Ikea hammer has an ergonomic rubber handle, so I used our wooden rolling pin! Miracle!

    • @Striker50_
      @Striker50_  หลายเดือนก่อน

      WAH-LAH!! Nice!

  • @myidisinhim559
    @myidisinhim559 6 หลายเดือนก่อน +1

    Excellent. Used the hammer handle method and it worked fine. Thank you.

    • @Striker50_
      @Striker50_  6 หลายเดือนก่อน

      I love to see it worked for you as well 🙏

  • @terraXR
    @terraXR 5 หลายเดือนก่อน +1

    The bubble level with flat sides worked great - thanks!

    • @Striker50_
      @Striker50_  5 หลายเดือนก่อน

      @@terraXR nice! That was personally my favorite

  • @abhinavsingh2032
    @abhinavsingh2032 2 หลายเดือนก่อน +1

    Thanks Bro...😊
    I didn't have the tools you suggested. But inspired by your experience, i devised a strategem, in India it's called - JUGAAD.
    It worked...😅

    • @Striker50_
      @Striker50_  2 หลายเดือนก่อน

      @@abhinavsingh2032 Nice! 👍 I'm sure that will work every time 👌

  • @antonydasronny8674
    @antonydasronny8674 4 หลายเดือนก่อน +1

    Thank you so much for your video I was struggling to do it but with the help of you I finally did it ❤

    • @Striker50_
      @Striker50_  4 หลายเดือนก่อน

      @@antonydasronny8674 success 🙏🙏🙏

  • @lavenderzig7129
    @lavenderzig7129 7 หลายเดือนก่อน +1

    Thank you Thank you!!
    I finally find the right video help me to close up the back of watch.
    I will go find your part 1 video now

    • @Striker50_
      @Striker50_  7 หลายเดือนก่อน

      Nice! Glad to hear

  • @nikhithasd226
    @nikhithasd226 2 หลายเดือนก่อน +1

    What if the gasket is broken? Can it work with one?

    • @Striker50_
      @Striker50_  2 หลายเดือนก่อน

      @@nikhithasd226 The gasket is going to help keep the water out. The watch will still work but you may get water damage or dust. A local watch place may have a replacement gasket if it is broken and it shouldn't be that expensive. I would personally make sure to replace the gasket because that's going to help keep your watch running and not get damaged by water and such

  • @hongras5409
    @hongras5409 6 หลายเดือนก่อน +1

    Thank you. The book method did it for me. The snap was loud.

    • @Striker50_
      @Striker50_  6 หลายเดือนก่อน

      The snap sound is so rewarding

  • @199496db
    @199496db 6 หลายเดือนก่อน +2

    Thanks..arrow to the dial and applied pressure with a one foot straight wood. Circular pressure

    • @Striker50_
      @Striker50_  6 หลายเดือนก่อน

      Great to hear thanks for sharing ⌚

  • @mikel9735
    @mikel9735 7 วันที่ผ่านมา +2

    Crazy. I have the same tool kit or one that looks just like it. Thanks for the insightful video.

    • @Striker50_
      @Striker50_  7 วันที่ผ่านมา +1

      It's such a useful toolkit, has paid for itself multiple times now

  • @yamiking87
    @yamiking87 4 หลายเดือนก่อน +1

    Thanks man ... The book method was the best...finally my book was useful for something 😂🤣😂

    • @Striker50_
      @Striker50_  4 หลายเดือนก่อน +1

      @@yamiking87 It's only crazy if it doesn't work

  • @jonathanshields2016
    @jonathanshields2016 3 หลายเดือนก่อน +1

    The book worked for me. Thanks its a useful thing to learn.

    • @Striker50_
      @Striker50_  3 หลายเดือนก่อน

      @@jonathanshields2016 Yup 👍 now you have a skill for life

  • @al75703
    @al75703 9 หลายเดือนก่อน +1

    I wasn't having much luck, tried a rolling pin, finally I noticed a battery pack that had fallen out of an old laptop. It has a nice flat surface about 1 1/4" wide and that worked. (Now let's see if the laptop still works!) Thanks!

    • @Striker50_
      @Striker50_  9 หลายเดือนก่อน

      Lol! Proceed with caution! Don't want a re-occurence of what was happening with the Samsung cell phone batteries 💥

  • @Rickyboy_3000
    @Rickyboy_3000 7 หลายเดือนก่อน +1

    Used my small spirit level to put the back on my mums watch. Thanks for the tips!

    • @Striker50_
      @Striker50_  7 หลายเดือนก่อน

      Successsssss 💪

  • @bk14biker
    @bk14biker 5 หลายเดือนก่อน +1

    I've just changed the battery in my watch but no amount of pressure would pop it back in. I ended up using a piece of wood and having to kneel on it with almost all of my weight before it snapped in.

    • @Striker50_
      @Striker50_  5 หลายเดือนก่อน

      @@bk14biker way to go! ⌚😅

  • @cubeking3223
    @cubeking3223 4 หลายเดือนก่อน +1

    This is the right place man really u fixed my life along with my watch thanks a lot 😅😊

    • @Striker50_
      @Striker50_  4 หลายเดือนก่อน

      @@cubeking3223 Lol I don't think I did all that ☠️

  • @thebelissima64
    @thebelissima64 7 หลายเดือนก่อน +1

    Thank you so much! I used a wood rolling pin and it worked like a charm!

    • @Striker50_
      @Striker50_  7 หลายเดือนก่อน +1

      That sounds like it's working great for people!

  • @okidoke-xe8gj
    @okidoke-xe8gj 6 หลายเดือนก่อน +2

    OMG Dude,my Fossil men's watch is a very hard case...it was even very hard to get it off...it flew almost to the ceiling!They must have pressed it on with brutal force. Nothing works (even screw clamps etc)....I guess I'll buy one of these Amazon watch case presses for 20$ and hope that will work...this is and WILL be my only watch with snackback case ever,that's for sure!

    • @Striker50_
      @Striker50_  6 หลายเดือนก่อน

      Yeah I prefer the screw backs

    • @ceperezn
      @ceperezn 5 หลายเดือนก่อน +1

      Did you get it fixed? I have the same problem 😢.

    • @Striker50_
      @Striker50_  5 หลายเดือนก่อน

      @@ceperezn Do you perhaps have a family member that can assist with that If not a local repair shop should be able to do it

    • @okidoke-xe8gj
      @okidoke-xe8gj 5 หลายเดือนก่อน

      @@ceperezn so far not...I have to buy the press first and I doubt a press will help...maybe the back is deformed

    • @PatBall-v8q
      @PatBall-v8q 8 วันที่ผ่านมา

      Paid $8 for the battery - put in place - tried for over 2 hours and my Fossil just won't snap back in place. I'm thinking it is just the way Fossil makes them.

  • @ramonsequoia8586
    @ramonsequoia8586 9 หลายเดือนก่อน +1

    How do you make sure that the glass of the watch does not break?

    • @Striker50_
      @Striker50_  9 หลายเดือนก่อน +1

      Have some sort of padding under, & make sure it's on a flat surface. Too much padding might not leave enough pressure since there's too much give

  • @alanweir3567
    @alanweir3567 3 หลายเดือนก่อน +1

    I have a watch press and still couldn't get a back on.No matter how aligned it was or how hard I pressed.What I did was enter the back at the notched side for winder and squeezed the opposite side.The pop sound was mafnificent.

    • @Striker50_
      @Striker50_  3 หลายเดือนก่อน +1

      @@alanweir3567 It certainly is a satisfying noise. That's how you know you won the battle

  • @ErnestoOrtega-yo5fg
    @ErnestoOrtega-yo5fg 13 วันที่ผ่านมา +1

    Thank you soooo much, I fixed my watch because of this

    • @Striker50_
      @Striker50_  13 วันที่ผ่านมา

      Nice!! Glad it worked

  • @nylact
    @nylact 5 หลายเดือนก่อน +1

    🎯 Key points for quick navigation:
    00:14 *🔧 Use household items like screwdrivers or hardcover books to close Snapback watch cases without expensive tools.*
    00:43 *🔄 Record battery types and watch orientation before opening cases to avoid issues during reassembly.*
    01:23 *📘 Ensure rubber gaskets are aligned and use padded support beneath the watch to prevent scratching during closure.*
    02:37 *🌊 Fully inspect the case after closure to ensure it's properly sealed and waterproof.*
    05:12 *🔗 Reattach watch bracelets carefully using tools like mechanical pencils or dedicated kit tools for a secure fit.*
    Made with HARPA AI

    • @Striker50_
      @Striker50_  5 หลายเดือนก่อน

      @@nylact Incredible share thank you

  • @joshshaw1985
    @joshshaw1985 8 หลายเดือนก่อน +2

    Thanks for the vid. I found the book didn't work that well but a laptop power brick did the trick

    • @Striker50_
      @Striker50_  8 หลายเดือนก่อน

      I've done heard it all now 🤣 nice 👍

  • @demej00
    @demej00 5 หลายเดือนก่อน +1

    I just used two pieces of soft wood and vice grips. Snapped right into place with no marks or damage.

    • @Striker50_
      @Striker50_  5 หลายเดือนก่อน

      @@demej00 I'm glad to hear that worked for you! I try not to recc anything too wild bc I don't want anyone breaking their stuff

    • @demej00
      @demej00 5 หลายเดือนก่อน +1

      @@Striker50_ Yeah, haha, true. I read on a forum of someone always using his vice.

    • @Striker50_
      @Striker50_  5 หลายเดือนก่อน +1

      @@demej00 Yup that sounds like it works

  • @ShackledHalo
    @ShackledHalo 8 หลายเดือนก่อน +1

    Thank you so much! The hammer trick worked brilliantly.

    • @Striker50_
      @Striker50_  8 หลายเดือนก่อน +1

      That's great news 🗞️ ⌚

  • @OhShunz
    @OhShunz 11 หลายเดือนก่อน +1

    Great video!!! I'm over here pulling out my hair trying to get the back on a Timex Indiglo wafch after finally changing the battery after about 4 yrs of having the watch... only to realize the watch is only about $30 and my frustrations can be removed by just buying a new one LOL

    • @Striker50_
      @Striker50_  11 หลายเดือนก่อน +1

      Lol! But if you learn to change the battery, you learn a skill for life 🤌

  • @auronthas
    @auronthas 4 หลายเดือนก่อน +1

    i used watch back case press tool with soft cloth place on Mondaine watch face, yet i broke the watch glass when pressed 😢

    • @Striker50_
      @Striker50_  4 หลายเดือนก่อน

      @@auronthas dang even with a tool

  • @TJandJ
    @TJandJ 6 หลายเดือนก่อน +1

    Thanks dude u saved me a headache with this video😅

    • @Striker50_
      @Striker50_  6 หลายเดือนก่อน

      I got a headache myself 🤣

  • @jakemakesstuff3973
    @jakemakesstuff3973 11 วันที่ผ่านมา +1

    Hey thanks for the advice, book, handle of hammer & screwdriver didn't work, had to resort to a vice and two blocks of wood - Damn wife's cluse watch was a pain in the arse.

    • @Striker50_
      @Striker50_  11 วันที่ผ่านมา

      @@jakemakesstuff3973 Glad you kept with it nonetheless 🤘

  • @auriferous4462
    @auriferous4462 11 หลายเดือนก่อน +1

    Has worked a few times before with a Daniel Wellington, but 10 years later and even 90+kg force won't do it, now there's a dent in the back cover, I'll leave a comment if I find a solution. Good thing it's a cheap watch :)

    • @Striker50_
      @Striker50_  11 หลายเดือนก่อน +1

      Lol the DWs are something. A watch store might be able to get it on if they have a press

    • @auriferous4462
      @auriferous4462 11 หลายเดือนก่อน +1

      ​@@Striker50_ mounted the watch between two wooden planks and pressed lightly in a vise, snapped right in! It's a poor quality watch but at least the Japanese quartz has been keeping accurate time.

    • @Striker50_
      @Striker50_  11 หลายเดือนก่อน

      @@auriferous4462 Exactly, the movements themselves are usually Japanese and super accurate

  • @danm3188
    @danm3188 4 หลายเดือนก่อน +1

    I usually I just put the watch face down on a smooth surface, but not too hard like a wood or plastic table. Don't try with stone, metal, or glass surface. Then just push down firmly with the palm of my hand. Of course sometimes this doesn't work. Just trying to close a Timex watch the just WILL NOT snap back together.

    • @Striker50_
      @Striker50_  4 หลายเดือนก่อน

      @@danm3188 Not a bad idea

  • @narcisa.ciorgovean
    @narcisa.ciorgovean 10 หลายเดือนก่อน +1

    Thank you for sharing these tips! I used a hammer and it worked.

    • @Striker50_
      @Striker50_  10 หลายเดือนก่อน +1

      Nice! Glad to hear it worked with yours as well

  • @PoupouilleH
    @PoupouilleH หลายเดือนก่อน +1

    The book did the trick! Thanks 😁

    • @Striker50_
      @Striker50_  หลายเดือนก่อน

      @@PoupouilleH Nice! Book lovers may not be a fan of that strategy but it works!

  • @ArinehAA
    @ArinehAA ปีที่แล้ว +4

    Great video! I’ve been meaning to replace my watch battery for a while now, but wasn’t sure where to start

    • @Striker50_
      @Striker50_  ปีที่แล้ว

      You can do it! Watch my other video how to open it and let me know how it goes. I recommend the kit I bought on Amazon it makes it so easy

  • @JoeBlack666
    @JoeBlack666 2 หลายเดือนก่อน +1

    Using a hammer shaft bent my case back a little. What really worked for me was placing a small round wooden hammer on the case back and pressing it down with the rubber shaft of a metal hammer

    • @Striker50_
      @Striker50_  2 หลายเดือนก่อน

      @@JoeBlack666 Alignment of the back is a big factor for it to pop in to place. I struggled a lot initially
      Glad to hear it worked!!

  • @bluecollarbudgets
    @bluecollarbudgets ปีที่แล้ว +2

    Have a Fossil FS 5380 that the back will not snap back on....I've tried everything!!
    I even put watch on top of towel and laid a wrench across the back and stood, yes stood on top of it (balancing a couple hundred pounds) on the watch and still it won't snap back on.
    The glass front must be gorilla freaking glass or something because it hasn't shattered even with a tremendous amount of weight pushing down!

    • @Striker50_
      @Striker50_  ปีที่แล้ว +1

      Interesting to know! The Kenneth Cole watch in the video was like that prior to using the items. Do be sure to have some padding under, but not so much that the watch can't transfer the energy from excessive padding. If all else fails, you could always order a watch press on Amazon, or take it in to a local shop, they shouldnt charge more than $3-$5 since it takes about 20 seconds

    • @bluecollarbudgets
      @bluecollarbudgets ปีที่แล้ว +1

      @@Striker50_ thanks for the suggestions! I think I will take it to a local shop. Its not an expensive watch but it was a wedding gift so I don't want to risk breaking it.
      I am surprised at how strong the watch glass is though!

    • @Striker50_
      @Striker50_  ปีที่แล้ว

      @@bluecollarbudgets Agreed, before I made the video I tried putting all my weight on it and it didn't even budge!

  • @lincashin1187
    @lincashin1187 28 วันที่ผ่านมา +1

    Works great. I used the book. Thanks so much😅

    • @Striker50_
      @Striker50_  28 วันที่ผ่านมา +1

      It's so great hearing it work for others too

  • @robgreen708
    @robgreen708 6 หลายเดือนก่อน +1

    Hi I can’t get the back no matter what I use. Have managed to dislodge the second hand now

    • @Striker50_
      @Striker50_  6 หลายเดือนก่อน

      A watch repair shop can always close it for you, usually under $10

  • @gripperrod
    @gripperrod 5 หลายเดือนก่อน +1

    I tried all these methods too, unfortunately my Skagen watch resisted hammers, screwdrivers etc with all my weight on it, in the end I 3D printed a die to match the crystal size and put it in a vice. It finally worked.😅

    • @Striker50_
      @Striker50_  5 หลายเดือนก่อน

      @@gripperrod Man Skagens are sounding to be the most difficult
      The vice has worked for a lot of people apparently

  • @mili224
    @mili224 10 หลายเดือนก่อน +1

    Good tips, but the only thing that worked for me was squeezing the watch in a vice! I padded the crystal with a nylon washer and thin wood for the back. Sloooowly turned the vice until the magic 'click'! I would say this method should be tried after all others. Crazy that it is so difficult to get these backs on!

    • @Striker50_
      @Striker50_  10 หลายเดือนก่อน

      Add that to the list of things that works 👌
      Exactly, I didn't try again for months the first time it didn't go on

  • @PHANTOM-ih4gx
    @PHANTOM-ih4gx 4 หลายเดือนก่อน +2

    So if none of these vids can help me, must Mean mine is defekt.
    It simply doesn't want to close with or without the O-ring.

    • @Striker50_
      @Striker50_  4 หลายเดือนก่อน

      @@PHANTOM-ih4gx ticket to a local watch shop a lot of times they have extra parts and it's pretty cheap maybe 10 bucks to close it

  • @dennispinkstaff1681
    @dennispinkstaff1681 5 หลายเดือนก่อน +1

    Totally works for me! You saved me again.....

    • @Striker50_
      @Striker50_  5 หลายเดือนก่อน

      @@dennispinkstaff1681 Let's goooooo 🤙

  • @zaldygonzales08
    @zaldygonzales08 ปีที่แล้ว +4

    Thanks bro! I used the level tool.

    • @Striker50_
      @Striker50_  ปีที่แล้ว

      Nice! That's awesome to hear

  • @tina812m
    @tina812m 10 หลายเดือนก่อน +2

    Thank you for the lesson. Really interesting.

    • @Striker50_
      @Striker50_  10 หลายเดือนก่อน

      Anytime 👍

  • @outspoken3297
    @outspoken3297 3 หลายเดือนก่อน +1

    Nice and simple to the point ❤

    • @Striker50_
      @Striker50_  3 หลายเดือนก่อน

      @@outspoken3297 🙏🤙🙏

  • @greg7sammons
    @greg7sammons 3 หลายเดือนก่อน +1

    Last time I tried to replace the battery in my wife's Timex I broke the crystal. This time I watched your video and used the handle on my hammer method and bingo nothing to it, thanks a bunch.

    • @Striker50_
      @Striker50_  3 หลายเดือนก่อน

      @@greg7sammons 💪👌💪👌

  • @EricTorreborre
    @EricTorreborre 14 ชั่วโมงที่ผ่านมา +1

    I actually used the palm of my hand, with good vertical pressure, and it worked perfectly.

    • @Striker50_
      @Striker50_  9 ชั่วโมงที่ผ่านมา

      you would be a perfect CPR teacher

    • @EricTorreborre
      @EricTorreborre 8 ชั่วโมงที่ผ่านมา

      @Striker50_ 😄

  • @Vanichi
    @Vanichi 6 วันที่ผ่านมา +1

    Salvou a minha vida 🎉 Tantos vídeos que eu procurei, mas especificamente esse foi o que me ajudou. Usei uma colher de pau 😅

    • @Striker50_
      @Striker50_  6 วันที่ผ่านมา

      @@Vanichi Gracias por compartir que este video te ayudo 👏

  • @Crazeyf
    @Crazeyf 5 หลายเดือนก่อน +1

    This video helped me! Thanks for posting.

    • @Striker50_
      @Striker50_  5 หลายเดือนก่อน

      @@Crazeyf glad it helped Thank you for sharing 🙏

  • @J_Life2100
    @J_Life2100 6 หลายเดือนก่อน +1

    I missed part one of this series I have 1950's 1960's Idk movement #c18695 case#36720 14k Lucian Piccard 14k square 17jewel manual wind I want to open 🙏help

    • @Striker50_
      @Striker50_  6 หลายเดือนก่อน

      Local jewelers can assist with vintage watches as such sometimes they are a bit more delicate

  • @Chiimkimbab
    @Chiimkimbab หลายเดือนก่อน +1

    I use a level tool. It works!!! Thank you. 🥳

    • @Striker50_
      @Striker50_  หลายเดือนก่อน

      @@Chiimkimbab Nice!!! 👌👌👌

  • @DerangedMallard
    @DerangedMallard หลายเดือนก่อน +1

    Can someone explain why nothing ever works when I try it?

    • @Striker50_
      @Striker50_  หลายเดือนก่อน

      @@DerangedMallard story of my life

  • @Manga_Debates
    @Manga_Debates 6 วันที่ผ่านมา +1

    Thank you for your help I tried closing my nominal watch all last night and this morning until my thumbs were aching 😭

    • @Striker50_
      @Striker50_  6 วันที่ผ่านมา

      @@Manga_Debates That's toughhh. I'm glad this helped. It's all about technique

  • @dlsh70
    @dlsh70 4 หลายเดือนก่อน +1

    The handle of the hammer worked. Thanks!

    • @Striker50_
      @Striker50_  4 หลายเดือนก่อน

      @@dlsh70 thanks for sharing!