How To: Samsung Rear Tub Seal DC62-00156A
ฝัง
- เผยแพร่เมื่อ 12 ม.ค. 2015
- How To Replace: Samsung Rear Tub Seal DC62-00156A www.appliancepartspros.com/sam...
For a full article, please visit: www.appliancepartspros.com/b/...
Symptoms: It’s gone bad; you’re getting water leaking out of the back of the tub.
Tools: blocks of wood, Phillips screwdriver, small bowl, flathead screwdriver, pliers, wrench with 13mm socket with ratchet, tape, towel, 10mm socket and extension, 19mm socket and ratchet, hammer, blue thread sealer, locking pliers.
This Samsung made Washer Rear Tub Seal replaces the following older part numbers on Samsung Washers: 2070193.
Buy the new Washer Rear Tub Seal DC62-00156A here: www.appliancepartspros.com/sam...
Most orders delivered in 2 business days or less.
If you enjoyed this video, please click the like button. Subscribe to this channel for more appliance repair tutorials.
If you need any more technical advice, call us at 1-877-477-7278 or chat with us on our website www.appliancepartspros.com/. We're available 7 days a week.
For more appliance advice, information, and tips, follow us on social media.
Facebook: / appliancepartspros
Twitter: / applpartspros - แนวปฏิบัติและการใช้ชีวิต
A few days ago , my washing machine was making lots of vibration when spinning. I called the technician and he told me that the drum was not round , it was oval, i had my doubt, i watch this video because i have a Samsung 2012 almost same model as this one on this video.
I did every step from this video , and i found my problem , it was the spider arm that had accumulated so much dirt in its arms, that it was unbalancing my machine. I must say a BIG THANK YOU TO YOU.
You saved me a brand new machine. The spider arm cost me 248$ canadians with the 6 bolts. And its working like a brand new machine.
So thank you very much.!!!! 👍👍👍👍👍👍👍🇨🇦
The technician had no clue! It could have been shocks or balance rings or spider arms. I started with shocks then balance rings then I found the spider arm like yours. I did not change seal.
I was given a free washer that wasn't working. This video was helpful. It was the bearings that needed to be replaced. When it was out, I also changed out the spider arm because at first it looked solid but then after cleaning a few holes showed up. I dont think I will buy a new appliance anymore, since the last few I bought new ended up neeing me to fix in within 5 years. So why not start with a free one and fix it. Shorly after getting the washer working, I found a matching samsung dryer for free as well. He said it didn't heat but it ran, turned out to be a $25 heating element. These videos you make cover so much it's good thanks.
Thank you a thousand times for making this video. It was so concise and walked me through the seal and bearing replacement of my Samsung front load washer. You saved me $1,000.00 this past weekend. Thank You!
video was a huge help repairing a samsung rear bearing at the same time the flange/spider that had broken...note to others as this is why to run a hot water load that is empty about once a month. To save the spider/flange braket from caking up with dirt and detergent causing it to rust/oxidize and fall apart.
Hello, I really have seen several videos, but your channel for me is the best, very well explained, camera very well focused, everything step by step. Thanks a lot . you are the best.
very nice video, i did my seal and bearings last weekend , so far everything is working fine, these machines are very easy to work on.
You are welcome! Glad you were able to fix your issue! If there is anything we can help you with in the future please let us know.
Good tutorial video. My 18 year old Hotpoint top loader is on it,s third replacement water pump and 2 sets of clutch liners, And all done from the underneath of the machine. And that,s all I have ever done to it!
Great step-by-step! Replaced my bearing set and seal. Instructions were well organized and correctly sequenced.
Glad we were able to help you out. If there is anything we can help you with in the future please let us know.
The bearings in mine are loud. It's basically the same job as this, plus a few extra steps. Thanks for making this video.
Thank you. Best video for this repair I could find!
You do a great job on these video's. Thank you for the time you spend making these.
Thanks so much, this video is amazing! ¡Saludos desde Mexico!
It's not an "easy" job, but it can be done if you go slow, watch the video and go step by step. It takes two people to manage the tub removal. I just finished replacing the seal and both bearings in our Samsung washer. One of the original bearings was bad, the other was better but still not like a new bearing, all due to a bad seal. The bearing/seal kit I ordered from you were exact replacements. Getting the stainless tub out of the bottom tub surround was not easy because of rust that accumulated in the bearings/shaft due to the bad seal. I put the bolt back into the shaft and used a small sledge hammer to finally get the shaft out. Not heavy hits, however. I used 0000 steel wool to clean the shaft before putting it back into the surround tub. Unfortunately, I had to do the job twice because when I put the tub surround back together I failed to put the heating element inside the bracket in the surround tub and the stainless tub rubbed on the heating element, but the job is much easier and faster the second time around. The washer is back in service!
4 hr Job non experience
Thanks so much for this - very well done. Washer runs like a top again!
Thanks so much for this video kind sir! Successful repair...
Power tools work great!
Thank you. First time washer repair, and it took me quite a few hours, but I was able to replace the rear bearing and squeeze some more life out of a washer that was only 2 years old.
Trestin, when you put the inner / outer tub back together, did you find that there was a small gaps between the bolts? Almost like the bolts are tightened too much. I am trying to make sure the darn thing does not leak. Thanks for your help.
ugh, I guess I am replacing my bearings and tub seal. However after 12 years or so of almost daily service, I am keeping this washer and giving it some much needed love.
Amazing video!! My bearing replacement went with out a hitch!
Çok güzel anlattınız teşekkür ederim
Thanks for taking the time to create this.
Thank you excellent video 💪🏻💪🏻
Excellently done video!
Thanks a lot for video.
Sir.. When inserting the shaft after bearing replacement, is it okay if i do not apply grease between the bearing and the shaft?
As always a very good and detailed presentation. It is on a new unit though. When I took mine apart the spider arm was all full of dirt. Also getting the unit through the box door was difficult as it is heavy. Some nuts very tight so need a long wrench and long extenders for sure.
Yeah probably a breeze on a brand new one, it would never go that smooth on a used washer
I'm just gonna get a new washer
Very good video. However when I took out the central seal, I took care not to damage the plastic tub in the point of application (holding) of screwdriver, but I scratched the wall of it with it's tip, and almost have to change the tub. You knew how much to insert the screwdriver under the seal not to damage the tub, but please tell the people that the tip of screwdriver may touch the tub and can scratch it under the central seal. It's very easy to scratch!!!
Yes. This video is the fix. Not too terrible - if you take your time and have basic mechanical aptitude.
Glad you found the video helpful.
How about just an unbalanced drum?
Is the cause a dirty spider seal?
Is there an adjustment to balance the drum?
Thank you sir
Simply Superb Video!. Thanks
You're welcome! Happy we could help.
Thank you, it's verry good instructions 😉
You're welcome. Glad we could help!
I saw your spider has a steel washer riding on the O-ring. My old one had this, but the new spider didn't come with a steel washer--just an o-ring. Is the washer important? Am I supposed to reuse the steel washer on the new spider, or just install it bare? The washer has razor sharp edges that could easily cut the seal!
When you pushed that seal in, did you push it only until the surface was flush, or until it wouldn't go in anymore?
Very good job sir thank,s
Your video was a huge help! Thank you!!
You are welcome! If there is anything we can help you with in the future please let us know.
You don't need a wave washer in this unit?
on samsung wf218anb/xaa 01 washer, how far do you push the oil/water seal into the plastic casing? There is an extra hair-line raise metal edge on the shaft right against the spider. Does the outer-bevelled edge of the oil seal ride on that extra ledge, or does it ride on the straight part even with where the other 2 inner edges of the seal ride on? Just wondering if the extra hairline raised area on the shaft is to catch hair that gets wrapped around shaft, so the hair does not ride or cut into the edge of the seal and get under it.
So this is what Weird Al Yankovic is doing now, I love this guy. Good video Al.
Good job but would it not been better to change seal and bearings at the same time but well done sir.
Thank you soooo much!!!! saved me mucho $$$
You are very welcome.
I did everything but for some reason the rotor wont fit back onto the spider arm. Same parts, all i changed were the bearings.
how can I get the rotor for the washing machine front loader coil and complete panel 110 volts the washing machine is 10 kg LG products and again for German machine please can you link me to store
Is there any video showing how to exchange the bearing? Thank you.
thats what im looking for
I went to the hardware store to get a new o ring for the bottom of the 35 mm shaft ,a small angled washer fits on top of the o ring then the water seal on top of that then the bearings.
Glad you were able to fix your appliance. If there is anything we can help you with in the future please let us know.
haw many MFD we put.if change
Dear sir,
How can repair washing machine control panel and automatic switches.
Please consult to me.
We don't recommend trying to repair control boards. They generally need to be replaced. For more information, you can give us a call at 1-877-477-7278 or you can chat us at our website: www.appliancepartspros.com/. We offer free technical advice and diagnosis.
I'm an Electrical technician.
WF405ATPASU/A2
It's a bit a of a PITA, but do yourself a favor and replace the bearings with quality Stainless Steel bearings while you are in there.
Rear (Motor Side) - SS6206ZZ - Stainless Steal ID 30mm x OD 62mm x W 16mm Double Shielded.
Front (Seal Side) - SS6207ZZ - Stainless Steal ID 35mm x OD 72mm x W 17mm Double Shielded.
The cheap bearings used from the factory and sold as replacements wear, which hastens seal failure. The seal failure allows water/detergent to rust the bearings. The rust accelerates bearing wear causing the seal to further degrade.
I changed the two bearings, oil seal and spider. It is much better, but when it rotates, its still unbalanced. Would that be bearing not fit properly? Or spider ? Or tub damaged from previous spins? Does anyone come here anymore?
Fine...
21:25 rear tub seal
Can these bearings be oiled with lithium grease or something?
Bearings are sealed
@@OOpSjm yep, I found that out....
What kind of grease does the seal need? The replacement i received didnt have grease inside
You should need any grease for this part.
Did he say easy????
Looks like a brand new washer..
I can't believe I am doing second set of washer bearing replacement... I am so mad at myself why I purchased this samsung washer at first place.
There might be and underlying issue causing the bearings to wear out prematurely. I would check your seals to make sure there aren't in leaks.
Very reasuring to see
Only a few minutes huh 🤣
Easy?
Might as well buy a new machine. I recently had one of these and given the cost of doing this that's what they opted to do. In this case, we suspected an article of clothing was between in inner and outer drum.
My red is on the left
Did you get to complete your repair? Is there anything we can help you with?
Plz sir ji Hindi dubbed
If only the washer was this clean after 8 years of consumer using way too much detergent. 50 minutes start to finish is my average time for this job. Have never done JUST a tub seal.btw.
Thanks sir