Home Automation: How to use 7 Program 0.1s to 9999 minutes Relay Timer XY-LJ02
ฝัง
- เผยแพร่เมื่อ 15 มิ.ย. 2024
- Step by step programming guide for Drok XY-LJ02 Relay time. This a great home automation project.
The best thank you for me is to not to skip ads and Subscribe 🔔 to my channel, like 👍 the video It is greatly appreciated. 🔔 😊.
I will reply to all Subscriber's 🔔 questions. So make sure to Subscribe and enable the bell 🔔.😊
****Get this item from:
Amazon USA: amzn.to/3iIJBw8
Amazon Canada amzn.to/2FcfSy1
Amazon Amazon Deutschland : amzn.to/2Id0P8F
Amazon UK amzn.to/34CpHhp
Amazon Italia : amzn.to/30LqjjC
Amazon España amzn.to/36Lu8cu
アマゾンジャパン amzn.to/3nywdyC
AliExpress: s.click.aliexpress.com/e/_9jgStn
Select chapters of this video
00:00 Start
01:49 Hardware Explained
05:21 Wiring Explained
07:03 General settings
10:41 P1 explained
12:18 P2 explained
13:15 P3 explained
14:21 P4 explained
15:30 P5 explained (you can set endless loop as in P5 and P6 ---)
17:03 P6 explained
18:29 P7 explained
Where to buy this and Download resources for this video: robojax.com/L/?id=228
Tutorial by Ahmad Shamshiri form Canada
****************************
Arduino Step by Step Course (over 100 lectures) Starts here • Lesson 00 What is Ardu...
Learn Arduino in 30 Minutes (video): robojax.com/L/?id=135
****************************
If you found this tutorial helpful, please support me so I can continue creating contents like this. Here is PayPal link paypal.me/robojaxTV
Follow me on Facebook robojaxTV
Follow me on Twitter: / robojaxtv
Follow me on Instagram: / robojax
Tutorial by Robojax.com
Get other projects code and learn Arduino
robojax.com/learn/arduino
*** AFFILIATE PROGRAM ***
We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.
#robojax #robojax_relay #robojax_timer - วิทยาศาสตร์และเทคโนโลยี
![บุกร้านไอศกรีม VJ วุ้นเส้น !!!! [ดูคลิปเต็มหน้าช่อง] #Short | PANG ORNHIRA](http://i.ytimg.com/vi/g549nEhKZdc/mqdefault.jpg)
Absolutely excellent tutorial, thanks for sharing this .
Yet another great video explanation,thanks!
Excellent tutorial! I purchased this item on Amazon for the purpose of opening a door latch with a 3-second 12v pulse once every 24 hours. From your description either P5 or P6 will do this after an initial trigger using 1440 minutes as my loop time. Please tell me I'm correct. The purpose for this is to open the door on my chicken coop every morning at 8AM... Thanks!
Absolutely brilliant explanation of this and its modes. I purchased soley on your video. Well done!!! Cheers from Indiana,USA
Exactly what I'm looking for. Thank you Sir!
Good to hear that. You are welcome
Great Job explaining and demonstrating! Thank you!
You are welcome
Thank you! This was very helpful
What a brilliant, if quite useless, piece of kit! Nice demo.
Excellent video! Thank you for taking the time to make it.
My pleasure!
Thanks!! Very helpful information
Great explanation. Thank you!
You are welcome.
Thanks, i found what I was looking for
Excellent video. Thanks for this.
Well explained, good review, the video answered my questions. Thanks! [ P4. Closed time before open time ]
Brilliant tutorial, thank you
Well explained, good review, the video answered my questions. Thanks! Best regards from Jalle😎in SWDEN
Glad it was helpful!. thanks for the donation.
HOLY GOD thank you, lol. The instructions that came with this leave a lot to be desired. I needed P7!
Glad it helped!
Thank you, Very well explained.
Glad you liked it
Thank you very much
Very useful, I got one of these as a timer for my resin curing station.
Great to hear!
Cool I wish I needed one.
very well explained thank you
You are welcome.
that's good. thank you
best explanation so one can follow and understand AK
Glad you liked it
Good job, great tutorial. Now I know it fits my need, and the mode I should choose is P6 --- loop a program many times and if there is a power outage, it'll restart. Thank you.
Glad it was helpful!
Well explained
Thank you, sir
very useful review, thx
you are welcome.
Thank you for the detailed explanation! This helped me better understand how to work the one I bought. I specifically purchased mine as an external watchdog timer for my home automation and security DVR computer. The intent was to have my HomeSeer controlled Arduino send a pulse to this timing module to keep resetting the clock. If it didn't reset (PC locked up) the relay would engage the PC reset switch. Unfortunately I can only configure this module to work the opposite. Using P7 the relay is always engaged and if the input is triggered (pulse from Arduino) before CL timeout then the relay will stay engaged. If PC locks up and and stops triggering the Arduino then CL will timeout and cause the relay to disengage, which could trigger the PC reset switch. Ideally I do not want the relay engaged 99% of the time. Instead I would like to keep the relay off with ongoing trigger timer resets and if there is not a reset (PC locked up) then engage the relay for 1 sec to reset PC. I have tried every combination I can think of with this module but don't think it is possible. Did I miss a setting? Do you have any other suggestions? Thanks in advance for any help.
you are welcome. check the wires connected to the relay to revers the affect.
Wonderful video, quick question: Would program P4 work with a switch on the trigger or does it need a pulsed input?
Good to know
Thank you
You are welcome.
Great tutorial RJ, I watched with great interest as I need 80 timers with with a 'Delay On' time of 4320 hours (180 days), for use as service interval reminders to turn on a 'Service Required' led pilot; can you tell me if this this Drok timer be modified to do what I want or do you know of another suitable timer? Thanks BJ
I hope you can help me. I purchased exactly this model of timer but it did not come with instructions on how to set it up. I do not have a push button. I have a product switch which controls a solenoid gate. The gate in normal position is closed. I want this gate to open 1/2 a second after the product switch was triggered by the product and the gate to close once the product passes completely by the product switch. How do do the setup? Thanks
I would love to use the OP without trigger button, but like program 6. only not the CL with it.
I'm building a battery operated light and want to shut it off automatically after 2 hours, or manually with a main switch.
When switching on the light again it should start counting again for 60 minutes.
Thanks 👍 very good job 👌, plz i have a question for example the P6 program there is just one OP and one CL , my question is if i can add Op2 and cl2, (i want to turn on the light twice per day 8Am and 5pm for 30min ) with unlimited loop
Big fan. Love your channel. Please please show us how to use the timer from a computer I would really love to learn how to do it. If you would show us how to do it I've learned so much from your channel and I really do thank you for everything you have taught me.
Thanks. I have a video showing how to send a signal from pc command line and turn on off a light with relay. You can use it for any other purpose. Control relay and AC bulb from Windows Shell Command line via USB and Arduino
th-cam.com/video/HzLCkzX5q3w/w-d-xo.html
good tutorial
Glad you think so!
Thank you, im going to use mine to trigger the glow plugs on my pickup. The trigger inside my pcm died so i installedba switch in the dash and ill use p5 to run the plugs 3 times 15 seconds each with 3 seconds in-between. All i need now is an enclosure, fuse and an led for the dash.
Nice sir....
thanks.
P4 looks like what I need, but instead of momentary switch I want it to begin as soon as power is supplied to the relay board. Can I just wire power to the trigger? Does it matter if the trigger remains on?
I have a deer feeder. This consists of a feed bin and an electric motor-generated feed disperser. The unit is powered by a solar panel. A "Moultrie timer" is introduced into the circuit, allowing programmable feed duration and timing intervals. This timer is unfortunately limited to feed intervals in whole seconds. I want to refine feeding intervals to fractions of a second, and I stumbled upon the XY-LJ02 as a solution.
I tested the device (with an on/off switch in place of the timer), setting it to P4 mode and a CL of 0.5 seconds then OP of 2.0 seconds and then turn off. On the bench it energized the load as intended.
But when I took the prewired device to the actual feeder, it didn't work! I'm concerned the problem is with my pre-wiring of the XY-LJ02. You mentioned in this tutorial changing the wiring on the left side of the device in the event of using an "external source" in lieu of a push button switch. I did not understand this explanation, it went too quick for me. HOW WOULD YOU WIRE THE XY-LJ02 FOR THIS FEEDER?
Stephen Hansen
I explain everything this module does demonstrate it. Now the scenario for each project might be different but you would have to use it withing the capability of this module. Perhaps watch it more than once to see how it functions.
I would really like to know if you can turn off the display while the timer is powered. I have mine powered 24 hours to activate a pump for 30 seconds per day. My lead-acid battery drains quite fast and I suspect that this is due to the brightly lit display which is permanently on. Thank you.
I would like to use program 4 but without CL; the output should remain switched on; is this feasible?
Great tutorial - And you have done that again! :) I just ordered my XY-LJ02 Relay Module from AliExpress. The main thing that i wanted to try is the Serial Commands using Rx and Tx - Since I am planning to set the relay far from the MCU and I don't want to set a new program from the module all the time - I want to be able to set the program itself and also If I should use a loop then gfive a count for it and set On and Off time for each one of the 7 Programs - and all of this I want to see how it can be done from the Rx and Tx - assuming that I will connect it directly to my MCU Rx and Tx as well. I can also be able to set more then one board from the Arduino (or any other MCU I choose) using a different pin-set for each one - i will need to set another Rx and Tx on the Arduino, I am not sure how But this is also something I am looking forward to test Maybe using the Software serial that way I can use more then one set of Rx and Tx Communications . GREAT JOB!!! thank You.
Thank you. If I saw people show interest in this module and if time permits, I will make video on that. I have 100s of other projects on my list but I am busy with full time job at a university and part time graduate studies and my family. So I have very tight schedule. Wish me luck.
@@robojax Good Luck!! :) Yes I know how it is!! same situation here. I hope you will have the time for the Serial as well - I will give it a go when the board comes. I think that it could be done and that would be great to be able to control the Relay behavior remotely.
I use this module for my motorcycle quickshifter..It only work at high rpm so i have a manual switch to turn off at low rpm..how do I set the trigger to be disable until it reach a certain RPM
Thank you for this informative video. I bought this relay based upon this video. The relay powers up on the micro USB source, but does not power up from a DC battery source into the + and - power input screws. I've tried 9v, 12v, and 16v. My wiring is the same as in your video - high trigger. Do you think I have a bad device? What power source did you use in this video when walking through the programs?
Hi, I have shown it. it can work with 6 to 24V. I don't remember anything. I have to watch to answer, so you watch it.
I need to actuate a solenoid 1 or 2 seconds after the relay receives power. It needs to actuate for 0.5 seconds, to actuate a momentary button. It then needs to shut off and not repeat unless powered down and then powered back up again. Can this relay do that?
Hi Robojax
Thanks for the learning video
I am searching for Something like P5 But starts with the relay off on off And finish with on can you help me please thanks
Hi, you are welcome. I don't have the module test it now. I don't know where I put it. But Remember you can connect your load or bulb to the Common and NC (normally close). I have shown it with Common and NO (normally Open), if you connect to Common and NC, the operation will be the opposite. Meaning if the module was turning something ON from OFF state, it will turn something OFF from ON state.
I'm building a hopper feeder. I want to trigger it, have it turn on and off rapidly 3 times and then stop until it is triggered again. Is that possible?
i fucking love you for showing measurements
So let me give you a situation.
Suppose I have a system I want to turn on after 1-2 hours after the trigger?
is it possible? but it will turn off immediately if the system has low input but will start 1-2 hours later is that possible?
Great video.
Can you explain the negative trigger? Again and also how to connect with low trigger??
Can’t be done better than this. When you say again it means play it again.
Have you ever made a video tutorial on the XY-BJ relay? I need to set it up on watering system to water plants every 7 days. Thanks.
Hello, I have made over 450 videos and don't remember. Here is how to find Specific TH-cam Video in a channel bit.ly/findTH-camVideo
If i hold trigger at P1, would it be restart the timer or not?
All of these time functions are time off delays and loops are AFTER being triggered. These boards should have been built with programmable time ON delay functions when triggered in all modes to be truly flexible...
Great Video. I want to build an auto garage door closer as we keep coming home and finding the door wide open. The problem is that every time the door motor receives a signal it will stop, and on the next signal reverse. This means we need a loop and then stop the loop once it actually closes. So I need to be able to have a delay of a few minutes once the reed switch activates, run a one second signal (to activate the door) and close it. Wait a minute to give it time to close, then if the reed switch remains open close the relay again for one second so the door activates again. This covers all options and the door will defiantly close. If we just have one signal then we might just end up opening it all the way when myself and the girlfriend both push the buttons when we leave.I am thinking P5 will do this.
Hi, I came across your comment and I did not understand it. Sorry.
Hello.... Fantastic device. I purchased three of these. 2 for my chicken coop project and one more to play with. The one function I'm confused about is when you press and hold in the stop button. What do these additional functions do. I was hoping a way to turn off the display to save power and extend the life of the display. Can you explain? Thanks!
Hi
I made this video to exactly answer these types of questions. If you watch the video more than once so you understand it. I have left nothing unexplained.
@@robojax Thanks... I figured it out.
Good Video. Would you be able to steer in the right direction. I'm trying to hook up a continuous switch to this relay. Seems like its made for a regular switch. I can get it to trigger when I push it in, but when I push it again so it can be in the off position. I can get nothing to trigger it. Thanks for your help and time
I am not sure if you can do it with this module as I have already forgotten what this do. But you should learn Arduino to do anything and I’m anyway you want. I have 30 minutes course link in description.
Thanks - great video. I have a 12v supply to a motor with a simple button switch to power the motor on. I want to add a 5 second delay after pressing the button but then get the motor to turn off 1 second after it starts up. Would this relay do the job? Also, do I need a separate 12v power supply for the relay or is there any way I can use the existing 12v supply to the motor to also power the relay.
Hello, I have done my best to leave nothing out. All features have been explained and demonstrated. I don't remember anything about this. So please watch all possible ways this works, if you can't find the solution, then this module can't do it. I have reviewed more of this types of relay timer if you search, you can find them. Find Specific TH-cam Video in a channel bit.ly/findTH-camVideo
That is program 4 with CL 5 sec and OP 1 sec
if I want the lamp to go out when the timer runs down do i connect it to normally close and common instead of Common-normaly open?
Yes you can connect it otherwise. Perhaps you have to watch the video again. I will reply to subscribers only.
Is there a way to program it so that it only counts down if the trigger is pushed? If the trigger is released I want the count down to stop. In P4. I’m using this to close a door. Once the door is full open it pushes and holds the trigger. It will count down to activate relay to close the door. If someone closes the door early the door will open at the end of count down and start the cycle over.
All possible functions have been explained. If you watched the video fully and did not find what you were looking for, then it can’t do it. Please watch.
Great Tutorial Ahmad, can a Inductive proximity sensor(NO) be connected to act as momentary switch when using P4, if yes which one would you recommend PNP or NPN. Thank you
this needs voltage as I've shown. so does not matter where it comes from. yes you can connect.
@@robojax I have tried a PNP proximity sensor(NO) but it does not turn on relay, proximity sensor does power up
Thank you. Is there a mode where pressing the trigger adds additional time. For example press trigger once switch is one for 5 seconds. Each additional press adds an additional 5 seconds. So if you want 30 seconds, tap trigger 6 times.
You are welcome. I have mode over 50 more videos after this and don't remember anything. When I make video about a module, I leave nothing out and explained all feature. So if you watch it without skipping the video, you should get the answer. Good luck.
No
How do you turn off the back light on this XY-LJ02 modual thank's
I don't know where I put the module to try it .
I watched this video 2 times, loop option is mentioned but option for endless loop not discussed..but in 3 digit 7 segment timer endless loop option discussed in one line
Can it be used to control time between zero and one second? To cut power to a solenoid.
you can set to 0.1 Second and control a load. It is up to you which load. Bulb or solenoid.
in P5 mode can we set the "off time" less than 1 second.. I have same board..
you can set from 0.1se and higher. Watch the video the video fully. and do NOT escape.
Please create the video of Connecting ESP8266 with STM32F103C8 Blue Pill Serial Communication (Not with AT Command)
I have a question. Can I use a Momentary switch to activate the relay via low trigger?
Perhaps you missed or you skipped the video. I have no extra stuff in this video. Please watch fully to get the answer. I have shown how to trigger it with NEGATIVE or LOW. I've just created page for this robojax.com/L/?id=228 the link is also in the description of vidoe.
Put the XY-LJ02 into an existing circuit. This circuit includes a timer (that provides impulses to load at programmed times and intervals), load (as a 6v DC electric motor), and a 6v battery. The XY-LJ02 will modulate the impulses from the timer to load to accomplish a certain goal.
Can this be done? How would you wire the XY-L02 here, and would it be triggered by the existing timer? Do you have a circuit diagram that you can point me to? Thanks.
I have not tested and not sure about it.
Hi. Any timer memory included? Do i need to reprogram this module everytime disconnect the power supply to the timer?
Hi, no you program it only once.
if the power off accidentally will it effect our program settings ? or from where it will start counting ?
it will start from the beginning of course.
Please upload one vdo for 60w motor and 12v relay arduino full connections ..
Use that tongling relay
Hi, I don't have it to upload it. this is very specific to you and very few people might want it. I have video on motor controller using relay. see it here th-cam.com/video/PjfPxxBTYiE/w-d-xo.html
I have a pump that is currently turned on by a pushbutton switch. I want to turn it on with a flow switch but then delay it from turning on again for 45 minutes before the flow switch can turn it on again. Will I be able to do this using P5?
I've explained all features in the best possible way. Load is load if you respect the power rating. I don't remember anything about this module now as I have over 450 videos. if you are convinced from the video that it can be done, then you should be able to use. May be watch the features more than once to know it better.
@@robojax I am now using it to turn on the pump. I am using a flow switch to turn the pump on with momentary close then leave the startup switch open for 30 minutes while the flow is still going. Before I put the relay timer on, I just had the flow switch triggering the pump but for some reason, the pump would turn back on every few minutes. This is working perfectly now that I have the relay timer installed. Thanks so much for your instructional video.
Should there be a fuse to protect the power input and/or trigger? Rating?
The fuse should be in your load or device. Usually the device you are controlling has protection. This is just extra switch to turn it off or on.
@@robojax thank you, but I was thinking about how to protect the product from a spike or something so it doesn’t get burned.
Hi. Is it possible to have the program set to turn on every 24 hours for 1 hour (in a loop like in P5 or P6), however during the time that it's not on (during hours 1-23) to use the P1 program where it turns on for a short time using a momentary push button
Hi, Every week I make 2 to 4 videos and don't remember what this module so. But I know this has the loop option, it so you can repeat it. I do my best to never leave any details unexplained. So please watch it carefully without skipping I am sure you will find the answer. good luck.
not sure if this is valid for this unit but on a related one there the documentation says an infinite loop is LOP = ---- vs 1-9999.
Hello,
Why does the back of the board look burned-up?
Many, many solder-points look like they melted. They show signs of extreme heat.
This DEFINITELY is not a healthy board. All of those points are now subject to corrosion and oxidation.
Can you explain what happened to this board?
This how it was shipped. I have no idea.
Can this device be used to latch an intermittent pulse power connection? I have a 12v dc current that turns my turn signals off and on in my vehicle. The time between off and on is 2 seconds. So the turn signals flash- rest- flash until the turn signal is moved to the neutral position. I want to use the left and right turn signal power lines to power my blind spot video cameras. If I hooked up my cameras right now the video would loop off and on until I finished my turn. I want the video to be constant until the turn signal trigger is moved to neutral. Will this device do that?
I explain everything this module does demonstrate it. Now the scenario for each project might be different but you would have to use it withing the capability of this module. Perhaps watch it more than once to see how it functions.
@@robojax I watched your video twice and I'm confused. Does this timer relay convert momentary to latch? I will not be connecting a constant power supply to this device. It will get a power trigger which is momentary. It will be a looping source until I manually shut it off. It is DC 12v. When I move my switch to on it will create a looping momentary power trigger every 2 seconds. In other words it is on-off-on-off and so on. I read that a timer relay can turn momentary power to latching until the trigger is removed. Where in your video covers this? Thankyou
I'm pretty new to doing circuits, I'm trying to make one for a senior project and I am thinking of using this timed module but I don't really understand what you mean when you say trigger
this is a DIY (do it yourself) module and you need to know a little about electronics. Trigger means a a voltage comes for a short period of time at the input of this module. or you apply some voltage at the input so it starts working like START button. The difference is that you need a pules (which is a voltage for a short moment).
@@robojax it's not required right? I'm gonna use operation 3.2 and it said on this website I found that a trigger is not required for this operation
operating it with trigger is one of the features of this device. so you use a feature that does not need any wire or external push button. I have clearly shown the trigger feature and mentioned it. So watch again,, pay attention and use the feature you need.
I bought 4 of these and after 4 hours i figured out how P6 worked and how to change the decimal. Also i found if LP IS
LP 0000 MEANS CONTINUOUS CYCLES.
Is there an instruction sheet that i can down load for this timer? If so where?
Also how can i program this timer using USB and what application do i use and what baud rate?
hey, there no information to control it via pC
Does it have a short circuit protection?
If it has, then should have mentioned it.
What is the load limit? I mean to ask can I use this for heavy motors of 3 phase 7hp - 10hp
Please do reply
I have motioned it when I spoke about relay. please watch. if you skip you will have tone of questions. My videos are different. watch them fully if you want to know. I answer any question that is 1-Related to the module 2-Not answered in the video.
programmable 3 relay logic module, please review this modules
I have done a video for dual relay which would have been the best solution to so many things and no one has watched it. This might be the same only few might need it.
seem to be having problem with timer. when i trigger the timer in p1 the relay and the small led comes on but i am getting no power coming out the outlet am i missing something here or is it defective answers please
Yes , check wiring.
hi, could you explain how uart works on this device
you are the 2nd or 3rd person asking for this. I don't see great interest to spend 1 to 2 days to learn and then spend 1 day to make video. Do online search, you may find something on it. Good luck.
Can I set up an endless loop or the number of circles is limited?
I bought it finaly :). It's possible to set up an endless loop.
How?
@@SamuelBSR How do you set up an endless loop ?
@@hasansahin216 To be honest, I don't remember but it was easy, I figured everything out intuitevely in 20min. The product is really cool I have no problems with at all.
you can set endless loop as in P5 and P6 --
Hyyy i hope everything is good. I need some help i have this project. And my goal is
to control two 12v fan
I have a. L298N motor driver controller
I also have a. timer delay relay
I also have a .elegoo uno r3
I also have a. Lcd screen 1602A
And it should all be controlled by the bluetooth dsd. My goal is to be able to controlthe fans with my phone. I want to be able to set a timer on the fans and also turn it off when i want. Is there any way you can help me
this is the most complex project I have seen. Each needs separate project and I have video for all of them. Search my channel and do it ONE by one and then put it together.
when in p1 0.10 sec and hold the trigger, will it loop or wait for next trigger??
if I want to answer, it I would have to watch it. any time you set for waiting will happen as waiting. but it is very quick 1/10 of a second.
its for a quickshifter application... so if it loops i cannot use it.
P1 cannot loop. Loop can be set only for p5 and higher
Hello Sir. I need your help to connect Arduino Ultrasonic sensor to timer relay XY-J02 instead of arduino uno or nano. Plz if you show me the wiring diagram. Thanks.
Hello, I have times of videos where things have been explained. Just search my channel and you find something that is useful to you.
I'd like to see a PIR as the trigger device instead of a button switch.
I have few videos on PIR and they can be used very easily
P.S. the aforementioned solar panel's energy is stored in a 6 v battery.
thanks for tip.
how to wire this for low trigger ?
you will need to make external circuit to do that. Here is a circuit snipboard.io/vERWPt.jpg
Hmmm....I want it to simply wait ~10seconds after being triggered to power something (a delay switch). I did not see this function.
Well, not what I wanted, but this is what I did. I wanted all my car electronics to come on ~10 seconds after the car starts....that way the car batteries voltage goes to the cars important components, and not secondary electronics that don't need to be on right away sucking voltage.
I went P4 CL 10 seconds (so items stay off after being triggered because the car turns on), and I set OP for something ridiculous like 300 minutes (5 hours). Because at no time will I be driving 5 hours non stop....if I ever do I just restart the car to get ~5 more hours, or increase the countdown to saying 12 hrs.
wow. cool project. Good luck
@@Blakelikesfood I watched this video and read damn near all the reviews on Amazon for this. I got lucky reading the comments to find you did what I am looking to do. I need to power another relay 3min after the vehicle starts. Looks like you figured it out. Thanks for posting.
@@boggerdak Been working great for a year....for the "ON Timer" I just set it to like 5 hours (to stay on) because at no time would I drive 5 hours non-stop. If I ever did, I'd just restart the car to get another 5 hours. Or, pull the dash apart and reset the timer to more time.
@@Blakelikesfood How did you get the P4 CL to operate before the OP?
How to integrate this in a dc tig welding machine
@@robojax i found someone who managed to install it within the circuitry of his welder.. just didn't show how he did it.. link here: th-cam.com/video/a2VSKFz6IDs/w-d-xo.html
relay is a switch. I don't know how to the machine function. but if you have to learn that machine, then use this module to turn it ON/OFF with specific timing.
is it possible to set endless loop ..in p6 mode.. how
I never leaves such important feature out. If there is loop option, then unlimited is also offered. I dont remember anything about this as I have made over 400 more videos after this. So please watch and get your answer.
@@robojax I watched this video 2 times, loop option is mentioned but option for endless loop not discussed..but in 3 digit 7 segment timer endless loop option discussed in one line
again checked found it is programme mode P6 , timing 17.10
as I understood max loop time can be 9999 times , but nothing mentioned about endless loop
On other similar but not identical boards you can get loop setting _ _ _ all dashes, which gives unlimited loops
I watched this video 2 times, loop option is mentioned but option for endless loop not discussed..but in 3 digit 7 segment timer endless loop option discussed in one line
I just watched the video and you can set loop for 9999 and it is till not enough? I am not sure but try setting it to 0000 and it must mean unlimited or try going below 1 to see if there is something else.