Great video. Thank you. I used the same Crux SWRTY 61N for my non jbl 2016 tundra. The dash speakers are the only speakers that work now. It is like the factory amp is not coming on, though I read it always is on. Any thoughts on troubleshooting? Any help appreciated.
I have Tundra w/ JBL and the seven inch was a little too small for so will get a 9 in Car Radio Dash Frame Fascia Panel Trim for it fit flush in dash… I ran into that problem today when installing
Well, it's not "all fake" as you originally stated. Each vehicle has various use and milage on it, older vehicles with higher miles are usually not as tight as newer vehicles off the lot. Do you best, you can use a putty knife or thinner blade to get a better start on your panel removal.
Hi I just replace the factory radio on my 2019 tundra and I’m using the maestro harness.I want to install a amp like yours so I just run the speaker wires from the radio to the amp.plus I have to get the amp harness to bypass the factory amp??? 2-do I loose the sound on my center speaker on the dash.. I appreciate your help
Are you getting your steering wheel controls. I have lost the hang up and hand receiver up buttons. The hand receiver up button hangs up a call and the hang up button does nothing.
@@elbaron51 Crutchfield did not send a mystro , they sent something g different. I guess I'm going to get one and do it all over again, and this probably means a lot of wire cutting and sodering. I did a lot of it when I was 30 but I was hoping to pay and have it done for me. At 66 it would be nice to see someone do anything correctly. I guess if you want it done right you got to do it your self. That's why I'm still changing my own oil, I can't trust a garage to to it without breaking stuff. How many air filter clips can a shop break in a year.
![🔴 ฟุตบอลแชมป์กีฬา 7HD แชมเปียน คัพ 2024 [รอบรองชนะเลิศ]](http://i.ytimg.com/vi/zPm8ClLVhoE/mqdefault.jpg)
Parts used are linked in the description of the video!
good video.. CAN you replace the radio on/off push button on a 2017 Tundra and not replace the entire radio unit?
Great video. Thank you. I used the same Crux SWRTY 61N for my non jbl 2016 tundra. The dash speakers are the only speakers that work now. It is like the factory amp is not coming on, though I read it always is on. Any thoughts on troubleshooting? Any help appreciated.
Hey I'd reach out to Crux tech support for help!
Is this too small when using car play? Not sure if I should upsize to 9” thanks
I have Tundra w/ JBL and the seven inch was a little too small for so will get a 9 in Car Radio Dash Frame Fascia Panel Trim for it fit flush in dash… I ran into that problem today when installing
Awesome video! Thanks. What brand dash kit do you recommend? From what I’ve seen, the plastic that is used to mount the radio seems flimsy at best.
Wish you guys had a video for the 61p
Where does the yellow and black wire connect to? I have a 2014 tundra so i have it in pin 15, but what wire does it need to connect to?
I purchased the CRUX kit you used here for my 2015 Tundra the camera and steering wheel controls don’t work at all. Not sure what to do now.
You need the Maestro box that can talk to the trucks steering wheel buttons.
Is this screen too small? Or just right?
Any idea why the sound is coming out from dash speakers only?
Do you have JBL? Sounds like the factory amp isn't turning on that drives all the other speakers.
In my 2017 there is no gap where you can get in and pry out the first piece at the bottom!
Well, it's not "all fake" as you originally stated. Each vehicle has various use and milage on it, older vehicles with higher miles are usually not as tight as newer vehicles off the lot. Do you best, you can use a putty knife or thinner blade to get a better start on your panel removal.
Do you have a link for a harness for JBL factory unit with factory jbl amp? I don't see the parts listed in the description.
Yep! It's the Crux SWRTY-61J If you have JBL and replacing the factory radio! amzn.to/2T1yw2m
Will the crux harness adapter work with any head unit?
Wat about the factory GPS plug?
Hi there is the 10 pin connector Color on the after market harnesses match up with the oem harnesses? Thanks.
I don't see the variation parts for the JBL system. Am I just missing them?
I missed it, sorry! Just added them now.
I used the same setup and my audio get cut off while driving any ideas?
Sounds like you have a short somewhere.
did the reverse cam work? I had purchased this for a 2014 Venza but the reverse cam didn't work!
On this truck, absolutely
@@ProvoBeastAudio Thanks much!
Hi I just replace the factory radio on my 2019 tundra and I’m using the maestro harness.I want to install a amp like yours so I just run the speaker wires from the radio to the amp.plus I have to get the amp harness to bypass the factory amp??? 2-do I loose the sound on my center speaker on the dash.. I appreciate your help
Are you getting your steering wheel controls. I have lost the hang up and hand receiver up buttons. The hand receiver up button hangs up a call and the hang up button does nothing.
@@feetincheseighths yes everything is working on my truck like it supposed too
@@feetincheseighths maybe you have two to reprogram the maestro in your computer after
@@elbaron51 Crutchfield did not send a mystro , they sent something g different. I guess I'm going to get one and do it all over again, and this probably means a lot of wire cutting and sodering. I did a lot of it when I was 30 but I was hoping to pay and have it done for me. At 66 it would be nice to see someone do anything correctly. I guess if you want it done right you got to do it your self. That's why I'm still changing my own oil, I can't trust a garage to to it without breaking stuff. How many air filter clips can a shop break in a year.
do you still have the original unit? I'm looking for one for my 2020 Tundra, as I want CD player
Not a personal vehicle.
@davew8542 I have a 2018 and might be interested in swapping since mine has a factory cd player
Lost me when you said “solder”…
You can crimp too you know, just don't twist and tape or use wire nuts!
@@ProvoBeastAudiojust curious why not wire nuts? They hold up pretty well in the electrical field, and if you tape them a little they never come off