There's no such thing as made to throw away where this gentleman comes from, I love it. I'm just trying to educate myself a little on basic testing of tcon as I have a suspected bad one.
Perfect way to find a short circuit in any electronic device . In this panel the supply line is short . So here is an another way to detect the defective parts , just remove the lvds and take a 3'7 volt battery approx 2 amp. Then connect the negative to the ground of the t con and the positive to 12 volt supply line . It will better to connect the positive terminal after the fuse , otherwise the fuse can be burn in second. In this process the faulty parts starts over heating and it can be detect easily. There are many youtubers who teaches how to find a problem in LED TVs but you are the best among them . In a very short time video your explanation is very logical and perfect. Respect from India , stay blessed always.
Your method is quite good but In some cases, the print of the circuit may get burnt when the shorted component is burnt by over current, so I do not apply that method. Moreover, when the short component can be found within 3/4 minutes, why would another method be applied. Best whishes Brother. Thanks a lot.
I have been working wrong In a short time watching you I have learned so many things in trouble shooting thank you for doing a video on trouble shooting
Just recently discovered your channel and working my way through your videos. Some excellent fault finding techniques and great information, really enjoyable to watch 👍 thank you.
Brother, just make a constant current supply of 100mA and feed in the short path. Then measure voltage in different points, where there is lowest voltage, that's the shorted component. The further you go from the short, the higher the voltage will be ( voltage will be in mv, drop will depend on trace Resistance). I made it in my mili ohm meter vdo
I feel inspired by your video and your explanation is cut throat... Do you have a course sir... I would like more of your videos to understand... Thank you... Kibet from Kenya
Morning there, I just came across your channel, And I like it, very interesting. I do have a Samsung Led tv that have on the left hand side blank screen and on the right hand side Vertical lines some of them narrower and other wider. I do see test points but do not know the voltages and for what I must test. Can you point me in the right direction please. Thank you
I have an Aiwa model AW32B4SM same issue with no display. Not getting any voltage at the current resistor on the tcon board. Trying to learn from your tutorials to solve my problem.
May God enlighten you and may God reward you with all the best. I follow you from Egypt - and I have a 3x1 mainboard. I want to know how to adjust the tachon voltage from 12 volts to 5 volts to work on the LCD screen. The tachon volts are 5 volts. Thank you very much
@@OrnatePixels Ameen thanks so you so much brother. Am still a learning and I have so many questions to ask you. Didn't know from where to start. Anyway if something is very important I will ask you In comments bro. JAZAKUMULAH KHAIR. Eid ul adha. Mubarak for Sunday.
There's no such thing as made to throw away where this gentleman comes from, I love it. I'm just trying to educate myself a little on basic testing of tcon as I have a suspected bad one.
Good job brother , keep it up
Thank You SO Much Brother
Perfect way to find a short circuit in any electronic device .
In this panel the supply line is short . So here is an another way to detect the defective parts , just remove the lvds and take a 3'7 volt battery approx 2 amp. Then connect the negative to the ground of the t con and the positive to 12 volt supply line . It will better to connect the positive terminal after the fuse , otherwise the fuse can be burn in second.
In this process the faulty parts starts over heating and it can be detect easily.
There are many youtubers who teaches how to find a problem in LED TVs but you are the best among them . In a very short time video your explanation is very logical and perfect.
Respect from India , stay blessed always.
Your method is quite good but
In some cases, the print of the circuit may get burnt when the shorted component is burnt by over current, so I do not apply that method.
Moreover, when the short component can be found within 3/4 minutes, why would another method be applied.
Best whishes Brother. Thanks a lot.
Probably the best informative on teaching basic repairs on circuits i have ever seen.
Thanks Brother
❤️🌹❤️
আপনার ভিডিও অনেক সুন্দর
This is the most interesting video about TV repair.... ❤❤❤ Please keep up the good work
good sir i like the way u explain the methods of fault finding, and especially is in English , keep doing what u do good
Aap ka video banane ke tareeke me ek point bahut good hi jo aap mark karke batate hi
Emeğine sağlık üstad. Başka takip ettiğim tamir kanalı dahi seni izliyor. Bilgi ve yeteneğinizle hayranım size. Allah CC emanet olun.Saygılar.
My friend thank you on your tutorial video more power from philippine
Ornie Peexel - My favorite channel!
I have been working wrong In a short time watching you I have learned so many things in trouble shooting thank you for doing a video on trouble shooting
Very good video.
Time is very important for any technicians . So sir your video is very nice and helpfull. Thank you very much.
Thank you so much brother
I am new on electronics,but your explanation out of more than 100 i have watched,your video is the best.
And it caters everyone in terms of languages,
Thanks and welcome
💗🧡🌹❤️💖
এর থেকে ভালো করে বুঝানো অসম্ভব। Thanks ❤️❤️❤️❤️❤️❤️❤️❤️❤️
Thanks a lot Brother
🌺🌹♥️🌹🌺
Saludos desde Perú. Excelentes tutoriales como hago para poder traducir a castellano su video
.Good morning! I'm from Brazil, congratulations on the excellent class.
Excelente explicación.... Gracias por su aporte amigo...... A los que menos sabemos.
Thank you so much brother
Keep up with this kind of method, your explanation is so good and understandable.
Top of the list youtube channel. . very Good information on your channel.thanks
I told before and I say again an again Mustafa is only one in all the world!
I wish if we have such a technician in my country Iran.
Sir aapke fault remove karney ka tarika aaccha hai thank you sir
your explain procedure is really so good sir. thank u so much for such knowledges.
Just recently discovered your channel and working my way through your videos. Some excellent fault finding techniques and great information, really enjoyable to watch 👍 thank you.
Thank you brother for all your efforts.
Most welcome, Thank you so much brother.
Good job, l am watching you for Ghana you are very good
Brother, just make a constant current supply of 100mA and feed in the short path. Then measure voltage in different points, where there is lowest voltage, that's the shorted component. The further you go from the short, the higher the voltage will be ( voltage will be in mv, drop will depend on trace Resistance). I made it in my mili ohm meter vdo
Resp Sir! Excellent Sir. Thank U Sir. -- Chinna Rao Andhrapradesh
Very cleared explanation my friend.
Thanks Brother
🌹❤️🌹
another one master 👌🇵🇭 perfect explanation
Thanks Brother
🌺🌹♥️🌹🌺
I just like how you explain in sampler friendly way..... Thanks
Sir you are a great trainer for as me tec
I am very happy to watch the vide thanks.
Daer Brother I. Like your Every VEDEO Very Much
Becouse Very Knoledgeble Vedeo
So Thanks
Most welcome Brother, Thank you so much.
Good morning thanks a lot for good teaching job, very nice sir
Thanks Brother
💐❤️❤️❤️💐
UR TOO BRILLIANT PLEASE KEEP IT UP GOD BLESS U
nice job, thanks for sharing
.
Thanks a lot you are a good teacher
Your voice quality is very good n clear.❤❤❤ 🙏🙏🙏🙏🙏
Thanks a lot Brother
🌺🌹♥️🌹🌺
Great explain sir, excellent.
Thanks Brother
You are a great worker and teacher❤❤❤
Thank you so much friend ❤
I feel inspired by your video and your explanation is cut throat... Do you have a course sir... I would like more of your videos to understand... Thank you... Kibet from Kenya
Verry good education quality
you make a good job to understand how to solve the problem.
My favourite this channel thank you this video
Thanks Brother
🌹🌺❤️🌺🌹
Well done Sir.Thank you
Really nice videos to watch, i don't mind longer videos, actually you should make longer versions 👍👍
Good job thank you ❤❤
You are genius ❤
Thanks master keep going 😃
Nice work thxs
Nice information sir Thanks ❤
Really excited good explaining Exlant tekenecalexport sir you are greatly appreciate it
Beautiful 🌹 good information sir
Hướng dẫn rất hay, rất chi tiết.
I am learning a lot from your videos. May Allah subhanawatala give you a suitable reward.
very nice sir thank you
Nice video thanks sir.
Wery goodgod bless from srilanka
very Well Explained Master👏👏👍
Bahut badiya sir
Thanks a lot Brother
🌺🌹♥️🌹🌺
Thanks for sharing your examination.
I like your tutorial Sir! God bless.
Morning there, I just came across your channel, And I like it, very interesting. I do have a Samsung Led tv that have on the left hand side blank screen and on the right hand side Vertical lines some of them narrower and other wider. I do see test points but do not know the voltages and for what I must test. Can you point me in the right direction please. Thank you
Very nice ❤
Buen día ING gracias por la excelente y importante información saludos cordiales desde villahermosa Tabasco México cuídese
smart lecture bro ❤
Great skills
Thanks for posting such a useful video.May god bless you sir with all good things and all success in your attempts
Thank You Very Very Much
🌺🌹♥️🌹🌺♥️
Good explanation with analog multimeter
Wonderful, thank you engineer mostafa
Thank you so much brother
AL-HAMDULILLAH! Success is so satisfying 👌🇧🇩
In sort time big solution , amazing expression.
Thanks Brother
🌺🌹♥️🌹🌺
Excellent 👌 very nice explanation 🙏
Thank you so much brother
,"nice and safe method, great job brother,👍🏻👍🏻👍🏻
Thanks Brother
🌺🌹♥️🌹🌺
my brother u r kindly give good lesson ,and if u r ok please make a vedio of dc power suply and gordak or smd ,
Very good explains dir sir
I have an Aiwa model AW32B4SM same issue with no display. Not getting any voltage at the current resistor on the tcon board. Trying to learn from your tutorials to solve my problem.
Gran trabajo, excelente la explicación.
Superb job 🎉
Thanks Brother
🌹🌺❤️🌺🌹
How are you. Your videos are very beautiful. Please tell me which country you are making videos from
May God enlighten you and may God reward you with all the best. I follow you from Egypt - and I have a 3x1 mainboard. I want to know how to adjust the tachon voltage from 12 volts to 5 volts to work on the LCD screen. The tachon volts are 5 volts. Thank you very much
Your explain very good sir
Thanks a lot Brother
🌺🌹♥️🌹🌺
AssLamualaikum I appreciate all work. And you explain well also. ❤️👍
Walaikum aas saalam. So nice of you. Thanks Brother.
@@OrnatePixels Ameen thanks so you so much brother. Am still a learning and I have so many questions to ask you.
Didn't know from where to start. Anyway if something is very important I will ask you In comments bro.
JAZAKUMULAH KHAIR.
Eid ul adha. Mubarak for Sunday.
Very help ful video
Thanks
Thanks Brother 🌿❤️🌿
Man you are good
My best teacher 🙏
Thanks Brother
🌺🌹♥️🌹🌺
Nice explain sir.thank you so much 💐💐
I am subscribed to day
Very nice information sir 👍👍👍👍
nice video ❤
Thank you,very important vedio.
You are welcome Brother.
Excellent explanation.
Great job, i have question what is the problem if vgh and vgl have no voltage, even vcc 12 is ok
Very nice video thank you sir
Thank you so much brother you Help me ❤
Very nice
Never ever seen for led tv video, 👍
Wawooo sir excellent work
Good job Pro
Goo job sir.... i wait next video....