Great work Sir. You have shared your years of experience to us in detail without any selfishness.... I pray almighty for your long, happy and prosperous life..
@@TRIVANDRUMBASEDKERALITE huge dedication is needed to get a high quality video with every minute informative The waiting for every each part is worth of it 👍🏻
How to install crank correctly, I mean to say the position of crank should be in the centre in between both the cases. So how can we adjust it? By knocking with hammer?
@@TRIVANDRUMBASEDKERALITE one of my friend used the hammer a little bit (not directly on the weight disc but put a washer on the clutch side and then used a pipe then hammered on that pipe) to align it will it cause any problem?
4 packing oo🙄 Exhaust duration, trafr duration oke koodum.. Rpm 1000 koodi koodum. Low end power kurayum mid and hogh end ppwer koodum. Jerking maarum. Mileage kurach kirayum. Compression num kurayum. Head mode cheyendi varum..
Hai bro.. Centre packing rx 135 no 100 no illa. Mannualil ath recomend cheyunnillaaa. Becoz packing thickness koodiyal crank compression kurayum.athakam oru reason. So use silicon based packing only
@@TRIVANDRUMBASEDKERALITE Thank you... But mostly packing varumpo center packing including anu varunna ella mechanicsum use chyunumind that's why i asked..
Bro nammal e hot and cold method veychu crank seat cheyumbol crank perfect aayi aanu seat ayi ennu ariyan engane pattum I ask these type of doubs because its my first restoration project Bro nammade crank crank case aayi fit cheyumbol feeler gauge use cheydu nokano Edayil clerance ethara ennuu
Njan marannu. Thau ennu paranjal 1 part of inch out of thousand. You can use new piston but check ovality of cylinder, then have a cross hayching(horning).
Bro sorry 4 delay in replay, i was searching for tis. 1.5 =38 micrones. If you use a new piston then it will run. Don't go for rebore. But your cylinder should be parallel, not tapered. If it is tapered then only go for rebore veruthe rebore cheyth size kalayandaaa. Cylinder horning to be done for rough surfacing...
Onnum parayan illa mashe . Full set . Oru doubt chodikkate . Crank caseil ullil oil seal varunna vandikk engane heat akki crank irakkum, i mean first bearing irakkiyathinu shesham chamberil oil seal varunna type . Oil seal uruki povoole 🤔 .rxinte case alla to vere pala 2 strokilum
@@TRIVANDRUMBASEDKERALITE Mm . Nokkam normal njn chetak okke thatti irakkaranu . Puller illathond pvc pipe vach. Cheyyaruth enn ariyam ennaum vere nivarti illathond anu . Rx entel puller und . Oru vandi reastorationil anu chetak 😊😊
നാട്ടിൽ വർക് ഷോപ്പ് തുടങ്ങു... നിങ്ങൾ പഞ്ചാബിൽ കമ്പനിയിൽ ആണോ അതോ നിങ്ങടെ ഷോപ്പ് ആണോ. ഇങ്ങനെ ക്ലിയർ ആയി പറഞ്ഞു കാണിച്ചു തരുന്ന വേറെ ഒരു ചാനലും ഞാൻ കണ്ടിട്ട് ഇല്ലാ 🙏 നിങ്ങൾ പുലി ആണ് ബ്രോ
தலைவா வேற லெவல் தலைவா நீ பண்றதெல்லாம்
മലയാളത്തിൽ ഇങ്ങനെ ഒരു വീഡിയോ കാത്തിരിക്കുവായിരുന്നു ♥️♥️♥️♥️
👍👍👍
Thanks bro
Great work Sir.
You have shared your years of experience to us in detail without any selfishness....
I pray almighty for your long, happy and prosperous life..
Thank u brother
Pwoli... Oru rekshayum illa..u r saying every details excellent.... Thanks mahn👏👏👏👍👍
Thanks jii
Very detailed and educative, don't understand ur language but still everything is clear . Love ❤😘 from Gujarat
Thanks jiii.
Please e share to others
Superb 😍
Thanjs bro
Super bro nice information 🔥🔥🔥
Hi
Hai bro
Super video.. full support 😍😍🤟❤️
Kandu kothichu....👍
Machaa ...my bike is fully ported with allied CDI coil ......should I use 2t pump ???
Pakka clear video machane 👍👍👍
Thanks bro
Machane video pwolichu❣️
waiting for nxt part💥❣️
Thanks...
Waiting for bullet restoration
Will do soon
❤️
Thanks
@@TRIVANDRUMBASEDKERALITE huge dedication is needed to get a high quality video with every minute informative
The waiting for every each part is worth of it 👍🏻
Thanks bro..
Your supports are the key.. 🔑🔑
am waiting for your part 8 vedio
Best assembly, very clear. Suberb.
Amazing ♥️ video
Thankss
Bro😍❤️❤️
Waiting ayirunnu❤️
🥰🥰🥰
നമ്മുടെ Crux ബൈക്ക് ഇതുപോലെ തന്നെ ആണോ set ചെയ്യണത്....
Awesome restoration bro....make more videos... About rx
Thanks bro... sur more videos ill come
Nalla clarity undu
Thanks bro
Nice video ✌👍
Thanks bro
Good
Thanks
How to install crank correctly, I mean to say the position of crank should be in the centre in between both the cases. So how can we adjust it? By knocking with hammer?
No hammering.
Crank puller is available..
Use that to allign centree
@@TRIVANDRUMBASEDKERALITE one of my friend used the hammer a little bit (not directly on the weight disc but put a washer on the clutch side and then used a pipe then hammered on that pipe) to align it will it cause any problem?
👍👍👍👍
💝
😍😍
👌👍
Thank you..
Ente ponnu bro, kidu...❤️❤️❤️
Thanks jii
Nalla vedio
Can you do a study on " How to work ACG stator on RX series bikes ".its common now a days
Machaneee.....happpy christmas.....💚
Katta waiting for nxt video and live😌💥💜
Next video varunnund.....
My RD 350 starting 😎
@@TRIVANDRUMBASEDKERALITE oh yeaaaaaaah💥❤️
Good job ❤️
Thanks
Poli
Thanks bro
Rx engine assemble/set മാത്രം ചെയ്യാൻ ഏത്ര മണിക്കൂർ എടുക്കും ?
Depends on quality of work
@@TRIVANDRUMBASEDKERALITE average എത്ര hour ??
Pwolich
Egane okke SOP follow cheythu restoration cheyyunna oru aasan ente nattil undayirunnegil ennu veruthe agrahichu pokunnu... ....oru old bullet brandan
Bulletum ithupole cheyyan pattum.
Old model engine rebuilt varunnund...
@@TRIVANDRUMBASEDKERALITE waiting
Bro crank reset chayan layth charg athrayakum
Polichu bro😘
👍👍
where to buy fullset bearing?
Ningal adipoli anu bro 😎
🐣🐣🐣🐣
Bearing number ( crankshaft) ഒന്നുടി ഒന്ന് ക്രോസ്സ് ref ചെയ്യൂ. Clutch side and magnet side നേരെ തിരിച്ചു അനെന്ന് തോന്നുന്നു.
Aano??? Chilappo thetti poyath ayrikkum.
Ellam ottakanu bro cheyunathh... 😔
@@TRIVANDRUMBASEDKERALITE Doubt ആണ് ബ്രോ. എന്തായാലും ഒന്ന് check ചെയ്യൂ.👍🏼 എന്നോടും പറയണേ.
@@TRIVANDRUMBASEDKERALITE Bro nammal assembly cheyda engine bearing ellam shiri aano ?
Appo 5 gear box engane set cheyyum athu onne explain cheyyammo bro
Kneedle baring evdnna vangiye bro
Bearingnu face nokkano insert cheyyumbol otta directionile insert akathullo?? Bearingil number koduthirikkunathu ethu sidil varanam ennu nokkano
Ethu sidil venamenkilum engraved side vaykkam. But kanunna bhagath vaychal vayichedith ath storil ninnum vangaan pattum..
👍🏿
Thankss
Kicker idel wheel problem...lock chadi pokunnu.... anthu cheyyan pattum.....parayamo...pls
Tig weld adich kuzhi nirach puthiya hole drill cheyendi varum.
Atrem cheriya brass bush ittalum mathi
Cylinder 1st bore cheyumbol head vallom cheyyano?
Pinne carburetor upjet cheyyano?
Vendaa atrak calculated aay rece spec cheythal matram head mod cheyendath ullu.
Stock set up nu head mod venda...
Torque wrench evide ninnanu vagiyath...ethra rupees ayii
AMAZON
Make and price please bro ?
Pls മൊബൈൽ നമ്പർ കിട്ടിയാൽ നന്നായിരുന്നു
24.35
വെച്ചു കെട്ടും
നോ ബ്രോ
ഇനിയും വേണം കാത്തിരിക്കാം
Oh that was an heartbroken.... comment.
Thanks bro for supportss
@@TRIVANDRUMBASEDKERALITE എന്നു
2 സ്ട്രോക് മോഹിയായ
2 സ്ട്രോക് ഇല്ലാത്ത
ലെ
ഞാൻ
Poli macha
😀😀
Bro. RTV 666 and RTV666T plus sealent thammil difference enthanu. Gas cut nu sealant Mataram mathiyakumo?
Ariyilla bro. 😔
🟥🟥🟥ഞാൻ ഇന്ന് ഒരു RXZ dismantle ചെയ്തപ്പോൾ cylinder ന്റെ അടിയിൽ 4 packing ഇട്ടത് കണ്ട് അത് കെണ്ട് ഉള്ളadvantage എന്താണ്🟥🟥🟥
4 packing oo🙄
Exhaust duration, trafr duration oke koodum..
Rpm 1000 koodi koodum.
Low end power kurayum mid and hogh end ppwer koodum.
Jerking maarum.
Mileage kurach kirayum.
Compression num kurayum. Head mode cheyendi varum..
@@TRIVANDRUMBASEDKERALITE ok tnx🥰🤗
rx 100 il initial pick kittan entha cheyendat
Bro bearings ethra rupees aii
Skf bearing kit evideninnu aanu kittiyathu? Any contact information? Pls reply bro
Ariyilla bro
@@TRIVANDRUMBASEDKERALITE Ok bro, no problem... bearing kit kityy.. almost engine set cheythu theernnu... video series orupadu help cheythu.. Thanks 😊
😘😘😘❤️
Passion plus full engine wrk video chayyamo
TH-cam ill und bro..
Athinte work enikk ariyilla.
I am not a mech..
Ok bro appo sherikum enthaa job
Brode അത്ര ക്ലിയർ ആയി പറയുന്നതും കാണിക്കുന്നതും ഞാൻ യൂട്യൂബിൽ കണ്ടില്ല അതോണ്ടാ ഞാൻ ചോദിച്ചത്.
ബ്രോ നല്ല ക്ലിയർ ആയി പറഞ്ഞു തന്നു താങ്ക്സ് ♥️
Thanks bro.
Just mechanism valare ishtamanu atre ullu
❤️❤️❤️❤️❤️
Thanks bro
Nalla poola editing nu tym ayi alley , kozhappamilla bro ellarkkum manassilayi so verthey ayilla hardworking
Hmm. Thanks for support
Broo. ..from where u buy the spare parts brooo
Nattil ninnum courier cheyichathanu spares
7012560325 spares available for yamaha
Center packing and sylcon ittal problem ntha undakuka instead of using sealent paste
Hai bro..
Centre packing rx 135 no 100 no illa.
Mannualil ath recomend cheyunnillaaa.
Becoz packing thickness koodiyal crank compression kurayum.athakam oru reason.
So use silicon based packing only
@@TRIVANDRUMBASEDKERALITE Thank you... But mostly packing varumpo center packing including anu varunna ella mechanicsum use chyunumind that's why i asked..
@@sachinskumar1661 ❤️✌️
@@TRIVANDRUMBASEDKERALITE Bearing coveril loose ayal nthu chyum.. Any idea ntethu magnet side bearing loose und coveril ennu workshopil paranju
Brw rx 135 1998 clutch bushe adichittum neutral edumbol vayakara knocking sound aane accelerate chyeyum korayum ethu nthu konda varune ? Engney ready akkan pattum
Primary wheel change cheyth nokku.
Eth over backlash moolam varunna issue aanu.
@@TRIVANDRUMBASEDKERALITE thanks brother ❤️
ത്രെഡ് repair എവിടെയാണ് ചെയ്തത് എത്ര രൂപയാകും കാർബറേറ്റർ ത്രെഡ് പോയി ഇതുപോലെ repair ചെയ്യാൻ pattumo
ബ്രോ സുസുക്കി സാമുറായ് ബൈക്കിന്റെ എഞ്ചിൻ വർക്കും ഇതുപോലെ തന്നെയാണോ റ്റു സ്ട്രോക്ക് എൻജിൻ ആണ്
Bro nammade crank crank case aayi fit cheyumbol feeler gauge use cheydu clerance ethara ?
Video yil und bro. 👍✌️✌️
Bro nammal e hot and cold method veychu crank seat cheyumbol crank perfect aayi aanu seat ayi ennu ariyan engane pattum I ask these type of doubs because its my first restoration project
Bro nammade crank crank case aayi fit cheyumbol feeler gauge use cheydu nokano
Edayil clerance ethara ennuu
Bro 4s and 5s engine setting same aano gear wheel assembly same aano njan e video kandu oru engine assembly cheyan pova adha choiche
Ellam same anu bro..
No difference
Cheta crank fit cheyumbol bearing chudakumbol bearing nthelum patuvo
Over heat cheyyaruth. 160 max
@@TRIVANDRUMBASEDKERALITE 160 max nnu vcha nna mean cheythe
@@vishnuvasudevan3237 160 digree centigrade
@@TRIVANDRUMBASEDKERALITE Thank you🥰
Bro rx 100 il CAT vachaal nthelum scene undo?
Eey. No scene
Bro fz engine rebuild cheyyan SKF bearing use cheythal kuzhappam undo atho original thanne use cheyynao
Ariyilla broii
Maco connecting rod nallathano ? size 3 , ayal kuzhappam undo
Bro engine oil use cheythalle lubricate cheyyande , 2t oil scene ille
Actually assembly to be done with assembling oil. It is different.
You can use 2t or 4t in assembly (we are not that mutch perfectionist )... 😍😍
@@TRIVANDRUMBASEDKERALITE Ningal perfectionist anu bro..... ✌✌❤❤
Torque wrench range parayamo??
Entelu ullath 1-7 kg-m aanu
Enik 0.5 muthal 7kg-m vare tight cheyyan pattum
Oru doubt undu 1 to 7 kg alle torque wrench range. Pinne enganeya 0.7 kg select cheyyunne?
1-7 anengilumm
0.5, 0.6, 0.7, 0.8, 0.9, 1, 1.1, 1.2, 1.3, etc...
Ingane aanu athil marking ullath
0.5 rounded aay 1 ennanu rangil mention cheythirikkunne...
@@TRIVANDRUMBASEDKERALITE thank you 👍
👌👌👌👌👌😀😀😀👍👍
Bro timken te bearing engane unde
Very good 22 g Punjab to asi
Bro 4 s to 5 s convention video cheyyamo
Bro koyo and skf numbering same aano
Bro next
Varunnunddd
Pwolii❤❤
Bro njn aa thou difference choichathu nku refer chythu inform chym paranjarunnu
Njan marannu.
Thau ennu paranjal 1 part of inch out of thousand.
You can use new piston but check ovality of cylinder, then have a cross hayching(horning).
@@TRIVANDRUMBASEDKERALITE 1.5 thou difference und enna paranja... Rebore chyatha standard piston ittu use chyamo
Bro sorry 4 delay in replay, i was searching for tis.
1.5 =38 micrones.
If you use a new piston then it will run. Don't go for rebore.
But your cylinder should be parallel, not tapered.
If it is tapered then only go for rebore veruthe rebore cheyth size kalayandaaa.
Cylinder horning to be done for rough surfacing...
@@TRIVANDRUMBASEDKERALITE Tapered ano ennu engna aryunna 1.5 thou difference und enna latheil choichapo paranjollu... Horning chythal size veendum koodathilla bore inte..
Ethil 5 speed set chyyan pattumo
Pattum.
Direct fit aanu
Bro 4 speed 5 speed manifold same ano
Same...
Whear can I get torque wrench and what could be the price
Amazon
rx 4speed covert 5speed video poduga macha
4s vandi illa macha....
4speed conversion 5speed how price macha, requirements tools sollu macha
Onnum parayan illa mashe . Full set .
Oru doubt chodikkate . Crank caseil ullil oil seal varunna vandikk engane heat akki crank irakkum, i mean first bearing irakkiyathinu shesham chamberil oil seal varunna type . Oil seal uruki povoole 🤔 .rxinte case alla to vere pala 2 strokilum
Crank puller use cheyyendi varum bro...
@@TRIVANDRUMBASEDKERALITE mm crank nalla pole freez cheytha nadakko. Puller kitoola 😓
@@ranjithp8650 over freez cheythalum seal nte pani thheerum... 😔😔
@@TRIVANDRUMBASEDKERALITE
Mm . Nokkam normal njn chetak okke thatti irakkaranu . Puller illathond pvc pipe vach. Cheyyaruth enn ariyam ennaum vere nivarti illathond anu . Rx entel puller und . Oru vandi reastorationil anu chetak 😊😊
@@ranjithp8650 wow you are a mech is it???
kicker jam ann appo nta chaya
Kicker spring issue ano atho piston pidichath ano ennu ariyanam.
Bro ella spares price mention cheyyo plz
Sure
Bro cang correct left side fulle seat akkano allengil centeril akkano next vido kanich thannal valiya upakaram
Manasilayilla doubt??
Give correct torque to magnet side and clutch side nuts..
Ath crankine center aki kolumm
Bro adutha videoil onne paranjal mathi
Enna crroct manassilavum
Bro ente 135 ippo ulle piston 0.10 aanu athu pooyittund adutha piston size etha idnde bro?
20 piston means second oversize. 50mm piston.
20 piston?
Harga blok cilinder Berapa?
What piston and connecting rod brand are you using bro?
Piston is sam😔
Connecting rod is also chathan (AR)
@@TRIVANDRUMBASEDKERALITE why Sam bro? I thought it's was a top pro.Will Sam piston be a good replacement to OEM piston?
@@maheshb8258 no sam is a poor piston, with low thermal efficiency..
So better to go for good brands
Then why did you choose that you could have gone to Goetze or top pro
@@maheshb8258 within the budget. Rebuild i am doing... so why.. 🤕🤕
Bro ശെരിക്കും bro ഇപ്പൊ എവടെ ആണ്???
Eppo punjab
നാട്ടിൽ വർക് ഷോപ്പ് തുടങ്ങു...
നിങ്ങൾ പഞ്ചാബിൽ കമ്പനിയിൽ ആണോ അതോ നിങ്ങടെ ഷോപ്പ് ആണോ.
ഇങ്ങനെ ക്ലിയർ ആയി പറഞ്ഞു കാണിച്ചു തരുന്ന വേറെ ഒരു ചാനലും ഞാൻ കണ്ടിട്ട് ഇല്ലാ 🙏
നിങ്ങൾ പുലി ആണ് ബ്രോ
@@mubarakmubu5288 vandi bhranth und atre ullu.... thanks for support
@@TRIVANDRUMBASEDKERALITE ഒന്നും അറിയാത്ത ഞാൻ നിങ്ങളെ ഒക്കെ കണ്ടു എന്റെ passion plus ഞാൻ തന്നെ ഫുൾ പണിതു
@@mubarakmubu5288 ഫുൾ support
Part 8 epol varum broiii
3 daysss
Heyy bro
😀😀👌👌👌👍👍👍
Suzuki engine bulid chayyo plzz😞
17:46
Machane nigal video series igane petanu therkuva enn parag vishamipikalle
Interest ullavar valare kuaravanu bro. That's truth
@@TRIVANDRUMBASEDKERALITE Aru paranju bro pwoli videos
Anu ningal verem vandideyum cheyyanm
Torque wrench Ethan
Wats number paranjutharumo
Plz
Machaney vdeo il ninnu ore paadu aryve kitty