Great Video! I took your advice and contacted Performance East and TJ is awesome. I'm picking up a set of doors tomorrow for our SP570 Premium, Thank you for your suggestion.
Hey bro, that is an official Polaris accessories front rack. Can see it on their site. Also, that thing don’t need the 6 outlets. It is soo powerful with just the 4. The 6 was designed for the full cab 4 seater FYI.
Thanks dude, so since this was so new at the time. There were no mud flap protectors for that area. So I bought the most heavy duty floor mats at Walmart and zip tied them under there. They have worked amazing and haven’t had a problem since I installed them.
Actually bro they don’t make them yet. I took the most heavy duty floor mats I could find at Walmart and cut them to fit that area. I then used very large zip ties to hold them in place. They work amazing and we’re only $20 lol. People ask me all the time about them. Grizztek is a company who normally makes stuff like that, but they don’t have them for this model yet.
received this kit for christmas how did you run the heater hose to the back without dropping the skid plate ?looks like that's the hardest part of the install as i don't have a lift
Hey bro, so I pulled up my floor board in the center of the ranger. You just pull out like 6 pushpins and it pulls up. I was able to snake it through from the radiator to where I could reach it under center floor board in the cab. Then, I lifted up the seat and removed the tray under passenger seat so I have access to battery area etc. I then reached up and continued to snake it to the back. Fairly simple. Just make sure that you zip tie that hose over to a frame rail so that way it doesn’t touch driveshaft. Because that will erode a hole into the line
Thanks for the great video! Off topic but can I ask about your doors? I’m going to order the heater but know I need hard doors for my 2021 Ranger. Can you share what kind they are and where you bought them? Thanks.
It works amazing bro. This past weekend it rained hardcore at the Offroad park. I came out after it stopped and the whole inside of my cab was covered with condensation. I started it up, turned heater on high, and within like 2 min it was clear. Side note, if you close the floor vents, it puts more pressure out the top vents so it will clear it up faster.
@@roydilliplane4090 I used some rubber/plastic expansion pucks. Where when you tighten them, they expand inside the holes on the top of the Ranger bed. So, put the puck in the hole with bolt sticking up, sit bed box on top with bolt sliding through slot of bed box. Put the washer and nut on, then tighten.
@@AdventureOps1 I’m checking on your ranger inferno heater install You said you didn’t drop the skid plate underneath. Did you have to take the center console out ? Or how did you get the hose back to that valve?
@@jeffhansford Correct, the center console where you would place your feet if you sat in th middle is what I pulled up, then I flipped the seat up and pulled the storage box out. This is so you can easily access your battery. By doing both I was able to fish the hose through all the way back to the valve.
You’ve got over 20k in that machine, could’ve had the XP and or northstar lol what’s the top speed of the 1000 since you added all the extra weight to it?
Haha not even close to the price of a north star my friend. Out the door a north star on average is $25,000. I have under $17,000 in this. Also, it really isn’t that much more weight. Maybe 200ish pounds. It’s still pretty damn fast. I haven’t topped it out cause I’m still breaking it in.
Great Video! I took your advice and contacted Performance East and TJ is awesome. I'm picking up a set of doors tomorrow for our SP570 Premium, Thank you for your suggestion.
The plier in the tool kit takes out the push darts rather well too
They also sell a (extension kit) that will add 2 additional outlets. So you would have 6 total outlets.
Hey bro, that is an official Polaris accessories front rack. Can see it on their site.
Also, that thing don’t need the 6 outlets. It is soo powerful with just the 4.
The 6 was designed for the full cab 4 seater FYI.
This video helped a lot thank you, how is the Inferno holding up?
nice. can you make a review on the hood rack?
Forsure dude, that is my next video that I will be doing. All the accessories that I have installed on the outside.
What is that you have plugged in sitting on your dash? Is that a heater too?
The openings in front of the rear wheels . What is covering that space under the seats ? Great information on the heater.
Thanks dude, so since this was so new at the time. There were no mud flap protectors for that area. So I bought the most heavy duty floor mats at Walmart and zip tied them under there.
They have worked amazing and haven’t had a problem since I installed them.
Hey man from like 25mins from goldboro.
Have u had this running in like-25 Celsius
Where did you get the engine protecters in front of the rear wheels
Actually bro they don’t make them yet. I took the most heavy duty floor mats I could find at Walmart and cut them to fit that area. I then used very large zip ties to hold them in place. They work amazing and we’re only $20 lol. People ask me all the time about them. Grizztek is a company who normally makes stuff like that, but they don’t have them for this model yet.
Is there a part # ? I've got the same wheeler. Thanks
received this kit for christmas how did you run the heater hose to the back without dropping the skid plate ?looks like that's the hardest part of the install as i don't have a lift
Hey bro, so I pulled up my floor board in the center of the ranger. You just pull out like 6 pushpins and it pulls up.
I was able to snake it through from the radiator to where I could reach it under center floor board in the cab. Then, I lifted up the seat and removed the tray under passenger seat so I have access to battery area etc.
I then reached up and continued to snake it to the back.
Fairly simple. Just make sure that you zip tie that hose over to a frame rail so that way it doesn’t touch driveshaft. Because that will erode a hole into the line
@@AdventureOps1 thank you
Thanks for the great video! Off topic but can I ask about your doors? I’m going to order the heater but know I need hard doors for my 2021 Ranger. Can you share what kind they are and where you bought them? Thanks.
Go to my channel, I did a whole other video about the doors🤙🇺🇸
Awesome review. Do you know how well the defrost works on this heater? Thanks
It works amazing bro. This past weekend it rained hardcore at the Offroad park. I came out after it stopped and the whole inside of my cab was covered with condensation. I started it up, turned heater on high, and within like 2 min it was clear.
Side note, if you close the floor vents, it puts more pressure out the top vents so it will clear it up faster.
Would love to get some info on that craftsman bed box! Where did you get it? Price? It looks great! Thanks!
Sorry for late reply. Got it at Lowe’s item #1053450
How did you mount it?
@@roydilliplane4090 I used some rubber/plastic expansion pucks.
Where when you tighten them, they expand inside the holes on the top of the Ranger bed.
So, put the puck in the hole with bolt sticking up, sit bed box on top with bolt sliding through slot of bed box. Put the washer and nut on, then tighten.
@@AdventureOps1 part number or link to those ? Or are they available through Amazon?
Do you need to drop the skid plate to install? Are can all install be done from above. ? Thank you
The instructions tell you to drop it, but I did not. I very easily installed everything without doing so.
Did you take the console inside the cab off? Or how did you get the hose under the cab to the valve in the back
@@AdventureOps1 I’m checking on your ranger inferno heater install You said you didn’t drop the skid plate underneath. Did you have to take the center console out ? Or how did you get the hose back to that valve?
@@jeffhansford Correct, the center console where you would place your feet if you sat in th middle is what I pulled up, then I flipped the seat up and pulled the storage box out. This is so you can easily access your battery. By doing both I was able to fish the hose through all the way back to the valve.
You’ve got over 20k in that machine, could’ve had the XP and or northstar lol what’s the top speed of the 1000 since you added all the extra weight to it?
Haha not even close to the price of a north star my friend. Out the door a north star on average is $25,000.
I have under $17,000 in this.
Also, it really isn’t that much more weight. Maybe 200ish pounds. It’s still pretty damn fast. I haven’t topped it out cause I’m still breaking it in.
Is this the same heater they advertise for the 2018 give or take, models?
No, 2019 or newer. Cab changed around then.
When in doubt, contact inferno directly.
Where can I find a front rack like that? Thanks!
And how much did it cost? Thanks
Little warning to Canadians, a $400 US heater will cost you including exchange, shipping industry other crap $900 Canadian
More than 25k for a Northstar
U pay for half water when u can buy full strength and make 2 gallons for price of one