Make Your Own Fast RC Mini Racing Drone!
ฝัง
- เผยแพร่เมื่อ 5 มิ.ย. 2024
- Try out PCBWay: www.pcbway.com/
Get $5.00 in-credit welcome bonus after joining: www.pcbway.com/Member/Login/
---------------------------------------------------------------------
In this video, we're making a fast indoor/outdoor mini racing drone from some common materials, also using a JJRC/Eachine drone receiver board with a mini transmitter.
With a calculated top speed of around 30-35kph or 18-21mph, this racing drone is a true racer! It can handle being flown outdoors even in windy-ish conditions!
----------------------------------------------------------------------
👉 Visit my online Storefront: sites.google.com/view/maximag...
----------------------------------------------------------------------
☕ Buy me a coffee: www.buymeacoffee.com/MaxImagi...
----------------------------------------------------------------------
Instagram: @max.imagination - max.imagina...
Instructables page: www.instructables.com/member/...
----------------------------------------------------------------------
Disclaimer: Amazon purchase links below are affiliate links. It doesn't cost you extra to buy through those and I just get a tiny commission. Thank you!
Parts and materials needed to build this mini drone:
(x1) Transmitter/controller + Receiver - www.aliexpress.com/i/40002285...
(x4) 3.7V 6mm High-speed Coreless motor - amzn.to/3rUqPJm
(x4) Propellers - amzn.to/3g34aI5
(x1) 3.7V 150mAh Li-Po battery - amzn.to/3CD44ym
Or 3.7V 220mAh Li-Po battery - amzn.to/3ivxUPH
(x1) Short section of Plastic Cable Raceway (Trim off and use "U"-shaped sections) - amzn.to/3yGN35A
(x3) Popsicle sticks - amzn.to/3VtiIB6
(x1) Old ink pen
(x1) Square piece of foam
🪛🔧🔨 Tools and extra supplies I use:
➡️ Soldering Iron Kit - amzn.to/3X6L5Wq
➡️ Hot Glue Gun - amzn.to/3E6trJG
➡️ Drill Machine - amzn.to/3EDe0u8
➡️ Box cutter/Utility knife - amzn.to/3hP9MGI
➡️ X-Acto Hobby Knife - amzn.to/3XbL7ML
➡️ Cutting Matt (Green) - amzn.to/3gil71A
➡️ Needle-nose Pliers - amzn.to/3ECTKc3
➡️ Wire Cutters for Electronics - amzn.to/3ECut1B
➡️ Wire-stripping tool (Automatic) - amzn.to/3hQsMVD
➡️ Screwdriver kit - amzn.to/3V6vgNX
➡️ Heat-shrink Tube Kit - amzn.to/3AksTPE
➡️ Jumper Wire Kit - amzn.to/3UGhMZq
➡️ Breadboard for Prototyping - amzn.to/3GlF4ze
➡️ Perf Boards, Pin headers, and Connectors Kit - amzn.to/3AkySUw
➡️ Superglue - amzn.to/3EE6uis
➡️ Duct Tape - amzn.to/3g5mTU0
➡️ Double-sided Tape - amzn.to/3Edta82
➡️ Kapton Tape (for battery leads) - amzn.to/3X58bNl
---------------------------------------------------------------
//////////////////////////
Music credits:
Roboskater by Audionautix is licensed under a Creative Commons Attribution 4.0 license. creativecommons.org/licenses/...
Artist: audionautix.com/
Hip Hop Rap Instrumental (Crying Over You) by christophermorrow
/ chris-morrow-3
Creative Commons - Attribution 3.0 Unported- CC BY 3.0
Free Download / Stream: bit.ly/2AHA5G9
Music promoted by Audio Library • Hip Hop Rap Instrument...
V.I.P.N - "SKY" MOONY TRAP BEAT | No Copyright Trap
Free Download Link
bit.ly/3oQ6Ysv
V.I.P.N
th-cam.com/channels/2KS.html...
/ realvipn
/ vipnbeats
/ vipn
//////////////////////////
You may have also found this video by searching the following keywords:
drone, quadcopter, racing drone, diy drone, diy quadcopter, homemade,
homemade drone, diy, how to make, how to, fast drone, easy to make, simple drone, easy to make drone, drone that can fly, flying drone, flying, budget drone build, drone build, rc, remote control, radio control, rc drone, at home, mini rc drone, mini drone, helicopter, copter, rc aircraft, aircraft, hover, Mini RC racing drone, DIY quadcopter, Fast mini drone, RC drone building, Mini racing drone tutorial, DIY racing quadcopter, How to make a mini drone, Build your own racing drone, Mini quadcopter DIY guide, Fast RC drone build, Mini drone racing tutorial, Step-by-step drone assembly, Racing drone building tips, DIY mini racing quadcopter, RC drone, Mini drone speed modifications, Racing drone components, Building a fast quadcopter, Mini drone racing techniques, Customizing your racing drone, Tips for building a mini racing drone, Mini drone modification guide, Building a lightweight racing quadcopter, Racing drone electronics guide, Mini drone aerodynamics tips
#racingdrone #quadcopter #diydrone - วิทยาศาสตร์และเทคโนโลยี
![[TH] VCT Masters Shanghai Playoffs DAY 5 // 100T vs PRX | FUT vs TH](http://i.ytimg.com/vi/q75pv359eP4/mqdefault.jpg)
Hey everyone! The comment section has finally been re-enabled over the whole channel after 2 years by TH-cam themselves who shut it down in the first place. Glad to be in touch with my viewers again! :)
hi i just have a question can something be attached to it like i want to fly it with esp8266 with small lipo battery is that possible can it hold that ?
@@Th3Exodia Hi, that may be possible if your ESP32 SoC is on its own without PCB. Yes, I believe with that it should lift.
Cheers,
Max
Pls can you give me the link for the receiver Bord pls
@@houseoflaugher7923 Hi, the only available purchase page of the receiver and transmitter is linked in the description below the video.
Cheers ✌🏻
Gggthcz
Great job lil bro!! My kids need friends like you..
I appreciate that!
Young and smart . I really love to see the young people like you 🐱
Thank you so much! I appreciate hearing such kind comments as your's :)
Can I use brushless motors instead with this accelerometer never mind the battery and other components?
No, it won't work. You'd need a different receiver with brushless ESCs for the motors.
Very cool. Great ideas in here.
Really cool DIY project
Thank you! 👍
your awesome dude your like Enstein or something I can't believe you built this racing drone!!!
Thanks so much :)
Amazing bro. salute your work...
Thank you 🙌
I do something similar with the legs but i flare my legs, on the upper portion, by making 3 cuts and fanning the top "wings" outwards, so when i drop the leg into the arms loop, it will naturally have resistance and not go any further. It provides that extra amount of security that I like having, so when I land or take off, the motor doesnt slip put up or out down. To prevent slipping down, you can make 2 slight cuts a few mm apart on the bottom bottom, and bend that portion in. When you place the motor in that bent in part will naturally clip the motor in place.
You sound ahead of your craft! That seems like a more secure solution for DIY drones when using cable raceways. Thanks for the tip!
Great drone
Thanks!
Cheers :)
Great DYI! Curious what the estimated cost was for this build? BTW second link on parts list is unavailable as of this post
Hi there, thanks for watching!
The cost for making this drone was about $10, the cost may vary depending on what parts you already have and don't.
Sorry about the unavailable product on that link, I couldn't find a substitute controller that's in stock, you'll either have to do a bit of your own searching around to find the corresponding part, or wait til the part is back in stock for that link. I don't really have any control of that.
Have a good weekend!
Cheers
Great work bro (full support)👍
Thanks for your support! 👍
@@MaxImagination thanks
watching from nepal. Bro you make very nice vedio🤠🤠
Thanks and welcome!
Max your projects are always good keep it up
I appreciate that, thanks!
I am subscribing
Very Cool Project Max!
And very Nice explanation.
Thanks a lot! 😀😊
It will fly
你的影片很棒 加油
Wow amazing bro nice video 👍👍👍
Many thanks! :D
wow nice
Thanks for watching! :)
The drone is really so cool,bro🔥🔥
Thank you! Stay tuned for the upcoming video on a micro FPV RC car!
Yo.. Nice work
Thanks! :D
Hi max I'm your big fan . I'm doing electrical projects like you . Nice to meet you . I'm from sri lanka
Hello, thanks for commenting!
Nice to communicate with you too ☺
I'll check your channel out ✌
You channel is actually a gem bro ❤
I appreciate that!
Comments are finally back. Amazing 🔥🔥
Yeah! Thanks for your support, KSP!
Great job,can you use small brushless motor instead of the brushed ones ?
Hi there. Thank you! No, brushless motors cannot be used with this type of drone.
Hey this is great and very informative for us beginners. Just one question though... What if you're buying the remote control and receiver circuit board individually? How do you sync them together?
Hi there. Thanks! You cannot easily sync a different factory remote and foreign receiver together as they're most likely programmed to operate on different channels and bands on a certain frequency.
@@MaxImagination Thanks for the reply. That's what I was thinking but just wanted to double check to make sure. Problem is, it seems that they are hard to find selling together, at least on eBay. So I had to check Ali Baba to find what I needed (remote + receiver). And sure enough, I think I was able find what I needed. Thanks again :)
so i was looking for the cable raceway and I couldn’t find it anywhere, do you know what kind it is?
Hi there. Thanks for watching. Here's a link to a cable raceway kit I recommend that contains the correct sections of track you can slice from to get a sturdy frame for your drone: amzn.to/3AEP9CY
Cheers,
Max
Nice video 🇧🇩🇧🇩🇧🇩🇧🇩🇧🇩
Hey Max, love your videos and I was looking to build a similar version of this drone but do you know what is the range of the drone, greetings from Croatia!
Hey! Thank you! It's range is around 50-100 meters.
Can u make like a TH-cam short on how to make a case for the controller because I got it but the controller comes without a case
Cool, You ever have any problems with over discharge on those batteries
Not that I've experienced. The circuit board regulates that and cuts off power for flight when the battery gets too low. However, it is up to you to unplug the battery to prevent over discharge from the light load of the blinking LEDs.
Good job 👍How many trust can get using one motor and what is the weight of this drone?
Thanks for your comment! It weighs 25 grams.
Great DIY! BTW Where to buy or get the remote?
Hi and thanks! The remote is currently unavailable in the market.
can u put camera on it, small one like 26gb
Hi there. Lightweight cameras such as 2-megapixel micro action cams may work. Anything heavier than 10 grams will restrict the drone from taking off into the air.
Do you have any info on what protocol that the receiver uses
I do not, unfortunately. You may have to dig deeper online.
Good I am from srilanka
I hope you respond cause im in need
so i bought eachine transmiter and a different eachine receiver and the both dont receive and transmit so what shall i do ?
or i should bind them?
plz help
Hi,
First, please tell me the Transmitter and receiver models you bought.
@@MaxImagination ok here are they
Eachine E50S RC Quadcopter Spare Parts Receiver Board
Eachine E57 RC Quadcopter Spare Parts Transmitter
Hey very good DIY i have just one questions how do you connect the controller to the receiver
Hi and thank you. The controller automatically pairs to the receiver after powering both.
@@MaxImagination okay thank you very much
Hi buddy!! Can we use the Radio controller made by you and how to give connection to the receiver that you made.Its and Emergency buddy Pls explain me❤
Hi there. I would have to show you how it needs to be done, I cannot explain that here in the comments... It is possible, though!
@@MaxImagination Ok Buddy.Please Make a video about that
I have a question can you also install an fpv camera on this drone??
Hi, yes you can. Though it may require you to get a different receiver of a more professional sort, that can support an FPV camera and system.
@@MaxImagination thank you
@@multigek2276 No problem! :)
What soldering tool do you use?
I use the soldering iron from a kit similar to this one, my brand though is 'Anbes'
www.amazon.com/Soldering-Iron-Kit-Temperature-Desoldering/dp/B07S61WT16/ref=sr_1_3?dchild=1&keywords=anbes+soldering+iron+kit&qid=1630107939&sr=8-3
Hey! I know its been a while since this video was uploaded, but i have a question. Im making an autonomous variation of your drone design, using a XIAO ESP32S3 Sense microcontroller, an mpu6050, and drv8833 motor drivers, I have 320 mAh lipo battery, and am using a tri copter design with 3 motors instead of 4, but for some reason, it stalls after running for a little bit at high speeds, do you have any idea why this is?
Hi there! Such issue sounds like something coming from the motor driver's end. You may have picked a motor driver too weak for the higher currents the motors reach when at full throttle. You will definitely need to check that first. Cheers.
Where can you see that same flight controller also the electric wire cover
Check it out via the purchase link below.
What of the remote control and battery
From where can i get the transmitter?
At the moment, it is hard to acquire this exact transmitter. It is unavailable in online stores. I will one day focus on making an Arduino based drone that anyone can get the parts for. Cheers.
@@MaxImagination thanks for replying
Btw can you make a receiver and transmitter based on infrared light emitting diodes and IR receivers??
How would u add a camera to this drone
A 2MP camera underneath with a lightweight battery should do.
Where can i buy this recirver. I am unable to open the link in the description
Hi,
Sorry about that!
It has become pretty difficult to find any online stored that sell such receiver and transmitter pair up until now. I found the exact pair for a decent price.
Purchase link:
www.rc-helicopter-spare-parts-online.com/jjrc-h36-e010-quadcopter-spare-parts-pcb-board-transmitter-p-11736.html
Hope that helps!
Cheers,
Max
@@MaxImagination thank you
👍.what motor you used for this. Is that 716 moter
6mm coreless motor
Thanks for this video, however some links (the one for the transmitter) seems to be broken. Could you please check them and update it. Thanks!
Hi, thanks for letting me know! I'll update the links soon!
@@MaxImagination Awesome! Thanks
It will be connected to controller or we have to connect it
You need a controller remotely connected to it via Radio Frequency, yes. No pairing needed, powering on the two devices simply does it.
Hi max i have loved this invention and i want to build to but i have a different transmitter and reciver it is squared shape pls help me do this
Pls i need help to make it and can we use 300 mah 3.7 volt lipo battery ?
I have a rectangle transmiter too
Hi. Thanks for watching! You could build yourself a drone with such receiver and battery. However, you'd probably need to scale up the frame in size (a bit) as well as the coreless motors.
Yes, you could.
Thanks thank you very much
Wow I like your all creation..
Thanks so much! Take care 😊✌
Bro max, can use bt5636cyrl receiver
Hi there. Never heard of it. I'll check it out.
Do You know the specifications of the receiver so I can get a transmitter for it?
It uses the "JR-NH010R" receiver board.
P.S. You can purchase the transmitter and receiver for it via the link in the video description.
I did some research but couldn’t find anything about the receiver
Do You have any info about the protocol it uses?
do we need to program the drone or not
Hi, if you're using the transmitter and receiver like the ones in the video, you don't have to, no.
What is the total weight of the drone? I will make one
~25 grams. Have fun making!
can we attach a camara with it
Hi, yes you can, but as any other little camera would probably outweigh the drone, we'd need to attach one with a small camera sensor which has a really simple function of just filming to a Micro SD card. Then I believe such a setup would work.
Cheers!
How do I know which part is front and back or left and right
The LEDs onboard the Receiver indicate direction. Blue = front, Red = back.
Thank you
What about the controller? Does any work?
Hi. Not just any controller works. You need to purchase or find a drone's receiver and transmitter pair that are programmed to work with one another.
Is there any motor speed controller
No as it's a part of the receiver board.
Max bro can I use 614 coreless motor with 3.7 380 mah battery And finally ask you my doubts comments are back 🎉🎉
Hi there, thanks for watching.
Yes you may use a 614 or even 612 type coreless motor with a 380mAh battery, sure :)
Yes, my comment section is back under all of my videos, finally TH-cam unblocked them
@@MaxImagination I am so happy bro 😊
@@CaptainDiesel873 :D
Great job bro.can my son get some classes from you?
Hi there! Thanks for your comment. Currently, I don't do classes, but in the future I may put together a course :)
Thanks. My son is waiting anxiously
how can I get a colorless motor
From Amazon: amzn.to/44BVGf1
Sadly i cant find the transmitter only a spare part of the transmitter
Apparently, they are out of stock on these transmitters at the moment, sorry! 😕
Hello, I am in India. The transmitter and receiver are unavailable here. Can you you please suggest any alternatives?
Hi there! I'd be unable to give you Amazon links to the parts you're missing, but I've found some purchase links from Banggood - Transmitter: www.banggood.com/Eachine-E017-Mini-RC-Drone-Quadcopter-Spare-Parts-Remote-Controller-Transmitter-p-1979012.html?cur_warehouse=CN&rmmds=buy
Receiver: www.banggood.com/Eachine-E017-Mini-RC-Drone-Quadcopter-Spare-Parts-Receiver-Board-p-1981798.html?rmmds=detail-left-hotproducts&cur_warehouse=CN&trace_id=bcd61680659630822
Cheers.
@@MaxImagination so, i have to do something to pair the transmitter and receiver? If yes, how?
How long will it take to come
Sorry, what did you mean?
Put the fpv camera
Name of the receiver you used
It does not have a "name", only a model number by which you will not find it online anymore. You can acquire these receiver boards online. This one came from a broken Eachine E010 drone.
Bro can I connect a camera on it
Yup, I think you can, as long as it's lightweight.
hi bro where can i get the pen pipe
😀
From one of your old ink pens 🤓
Or, you may purchase a new pen and use its plastic casing.
@@MaxImagination thanks bro i am the one who is browsing from kalpana and ia m aaharshan i am her son
Bro Max, I'ts such a pleasure to meet you. I'm your fan and I am from Srilanka.
I really want to make this product. So I checked out the link you gave in the description. Unfortunately they are Douglas I cant effort to buy it. Can you give a link for srilanka please?
Hi, Kalpana. Many thanks for following along with my journey!
Unfortunately due to the unavailability, you can no longer purchase the transmitter nor receiver/flight controller boards to make this drone, making it a harder project to complete. Sorry for the inconvenience!
Thanks for letting me know, but do you know any other store to buy these stuff?
And can we be friends
what if I have no receiver but have a transmitter?
Then you need to get a receiver.
What is your reseivers name?
"JR-NH010R" is my receiver board's name.
How much does it weigh?
Not sure, sorry! Currently I don't have a hobby scale to know its weight :/
Hello max do you do electrical engineering in school
I study it on my own online :)
How to make a remote
alternate link for transmitter
Don't have one at the moment, sorry about that!
I'd assume this transmitter and receiver pair are no longer being manufactured, therefore less and less sellers are out there for selling those.
Hello max please can buy this drone
Hello! I do not sell my projects. You can find other factory-made drones similar to this on online stores.
What about remote how to make remote ?????
I do not have a tutorial on the remote, sorry! The controller is currently unavailable to be purchased.
Max can you please send me the PCB and the control
I cannot do that for you. However, you can purchase the controller online.
what is the price only for these things
transmitter
receiver
motor
propelors
Hi,
The price may vary nowadays.
Transmitter - ~$10
Receiver - ~$12
Motors x4 - $6-8
Propellers - $2
What about software
No software config needed.
Bhai mobile ka camera 📷 to banana batao
Bro link not geting
Hi, there are links pasted in the description below my video, please check them out.
I wanted to make one but the materials needed are too expensive. I wish I could make something that's affordable hahahahaa
It is not so easy nor cheap to get drone parts to build one yourself. It takes a good investment to get something one can enjoy flying. Cheers.
I am your subscriber from india , can you pls send a cheap controller and receiver buying link pls , cuz your link won't be working
Pls it's dealer should be belong to india
Hi. I haven't been able to find a link to a controller and receiver pair that are made for this type of drone other than on where I linked already.
I suggest you do your own research online in your own country's online stores.
How much please ❤❤❤
Depending from the region you are in, price can vary from $15-45 US dollars to build one.
It's costing me 36 dollars which is a lot considering that I get 3 dollars monthly allowance. Lol
Max please 🙏 help I have a science project
the build is awesome but make sure you don't show your body to us 😅😅😉😉
Thanks for your comment. How was I showing my body?
can I pleas😢 have it
No, but you can try replicating it by making it!