Chevy Silverado P0449 Evap Vent Solenoid Replacement. Don't Use A Lighter !!
ฝัง
- เผยแพร่เมื่อ 14 ก.พ. 2022
- I have to replace an Evap system vent solenoid on this 07 Silverado. Here's some Do's & Dont's when performing this repair.
#wrenchingwithkenny #keepwrenching #chevytrucks #gmctrucks #gmcsierra #chevysilverado #oreillyautoparts #advanceautoparts #autozone #ventsolenoid #emissions #checkenginelight #ls #suburban #yukon #yukondenali #avalanche #wesselmotorworks #snapontools #snapon #fuel #p0449 #vacuumlines #vacuumleak - ยานยนต์และพาหนะ
![ฉันจะ "แพรี่" ให้หมด - ผู้แข็งแกร่งที่สุดในโลกอยากจะเป็นนักผจญภัยให้ได้ - ตอนที่ 04 [ซับไทย]](http://i.ytimg.com/vi/PvmuP8y9IPk/mqdefault.jpg)
![มองหน้ากันไม่ติด (Awkward) - โอ๊ต ปราโมทย์ FEAT. MAIYARAP [Official MV]](http://i.ytimg.com/vi/4b02SY_r6Gw/mqdefault.jpg)
Just went through this with my 15 Silverado, the dreaded P0449 code. Also, on my dash it was telling me to tighten gas cap. First thing I did was tighten gas cap, cleared the code and rechecked. 0449 code is back. Inspected hoses at filler neck. Sure enough a critter chewed on the plastic vent filter hose. Replaced that, cleared code and rescanned, code is back. Checked the EVAP solenoid and a wire had corroded not allowing current to the solenoid. Ordered a EVAP solenoid with wiring harness from Amazon for $30 would have been $70 from auto parts store, my solenoid was probably good, but since I'm into it best to just install a new one. Installed new solenoid / harness and again cleared the code. Fingers crossed, and rescanned. NO CODES. Hope this helps someone having the same issue.
Best video yet ...been clicking for 2 hours ... none have included the breather filter off to the side either. When i looked on Amazon for parts and seen that ..i was like ugh wtf is that now? And bam your video told me. 👍
I love the way you handled the mounting bracket for the solenoid valve. Well Done Sir!
keep up the awesome work
I enjoyed your video and was all set to tackle the job in my 04 Silverado with 4.3 V6, but unfortunately it was a different animal altogether. I had to search for the valve and it was to the outside of the frame rail on the V6 and you could just about get one hand up in there. The hose came off easy as it has a clip on the V6. Hardly any room to work on this version, and found a little help by removing the hold down bracket first. Again, thanks for your post, and hope this helps anyone working on a V6., have not found any V6 specific info on line.
Very helpfull much appreciated thank u
Can you make a video on how to use a test light and how you can ruin something. Humbly asking. Keep the great content coming
Yes !! Absolutely !! That may be a good one for me to make this weekend !! I will let you know when I post it !! Appreciate your input !!
Hi, how did the truck act to determine you needed a new solenoid. I'm getting a heavy gas odor by the back door and it acts like it doesn't want to take fuel from the pump
@@spikecamden9860I don't have the gas odor but I definitely have the slow fill at the pump issue. It'll take $1 worth and then back up amd click off and it'll do that several times before I can do a full, uninterrupted filling....
Thanks for the video.
You are welcome! I hope it helped. Thanks for watching & keep wrenching 🔧
ممنون مسترvra... kod... lrik
Where did you get the evap vent solinoid part at and do you need a new hose for the part
How did the other hose get attached? Was it with heat?
Are the filters for the GMC in the same area?
What's the name of the hose that had the crack in it?
The one I'm working on looks nothing like this, there's no hoses like that either, but the plug looks the same, I'm concerned. It also came with some sort of vent filter that is separate, that has a hose similar to yours. Could I be taking out something different?... *Edit, I have a breather just like yours, but still concerned about the solenoid canister
Heater hose works great too
What type of filter is that?
Heck yah. Did you just use regular fuel line to suffice?
How many foot of hose was needed ?
Greetings I love your videos but Does the hose with mini filter . Has to be in the front ? Under the cab because the one I ordered comes wit the mini hose and mini filter already connected
Its the preferred location. If you mount it towards the back, It will pick up more dirt than if mounted forward up by the trans under the cab. Hope this helps
thanks i have an 07 classic i have to do the same .. also do you know if they have fuel filters i cant find it underneath where it usually at ... and the filter on top of the trans was it diffucutl to get to thanks im working from the ground and im a DIY
My 04 sierra ony has the one in the tank I think they started doing that half way through the 04 I bought one that said would fit couldn't find it after i Google I learned it didn't have one
anyone know the gm part number of the evap vent solenoid
Is this the same for a 2008
I hear the whole assembly is 50 with hoses..I will check my houses before I order.Thanks
That long hose going from the small canister to the small box filter , can I zip tie that to the filler neck of the gas tank so I can access it easier ? When the transmission shop rebuilt my trans they zip tied it to the very top of my transmission I can barely reach it. And does it have to be a exact length ? I'm thinking of cutting the old one off and running a new piece of 5/8 heater hose. Thank you for your time.
That was part of an update that GM came out with . That spot on top of the trans tends to be the driest . I wouldn't see any reason you couldn't do what you're saying . And that hose length can be whatever . It doesn't matter.
Thanks for watching !!
@@WrenchingWithKenny Thanks for taking the time to respond. I'll give it a go. I know on some GMC's it's up under the gas cap area. Take care and thanks again.
@@John_D2 no problem . Let me know how you make out !
@@WrenchingWithKenny Will do !
When you do a smoke test and the smoke comes out from the filter side that goes on top of the transmission does that mean that the canisters is no good
No, it means the vacuum hose that goes to the solenoid on the intake manifold has a crack or break
I'm having a slow fill at the pump issue and i wonder if thats the cause of the code im getting. It'll take $1 worth and then back up and click off and it'll do that several times before I can do a full, uninterrupted filling....any ideas?
Sounds like the hose to the gas tank is crimped bent just enough to allow the gas through. Kenny did a video talking about this already.
I've got a 2013 Silverado. I can't seem to put my eyes on this part. Do I have to drop the tank?
Should have to drop the tank driver side right on the inside of frame after tank 👍🏻 hope that helped I just changed mine I have a 2010 but I didn’t know it came with a other filter!
boiling water?
I am very frustrated, my solenoid keeps failing. I have replaced this twice and need another one. Is this a parts quality issue or is there a practical reason why these keep failing?
Change the canister too. Or atleast clean it out.
They say you can fill the tank too much and it will fail
Wjt size heater hose and clamps
I believe it was 5/8
HOW DO YOU TAKE THE CONNECTOR OFF
The tube connecter gets pinched on the end to collapse it and release it . Try to get in there with compressed air and some WD40 . Sometimes you have to get inside the end with two 90 degree pics or small screwdrivers to pry the locking edges up
Can anyone tell me the part number and other info for the hose that's attached to the canister? th-cam.com/video/pwf9TN1gt8c/w-d-xo.html
where are you located? I'm currently having this same issue. if you don't mind me asking, how much do you charge for changing that?
I am in Shallotte NC. if you want to email me , I can discuss it further
@@WrenchingWithKenny I actually changed it myself. I called around and cheapest quote I got was $445. Took me an hour and a half but I got it done. Thanks.
I stuck my brother witha test light, and ruined him.
Put on a new hose - that one is cracked way too much - rather dangerous - suggestion
He was serious when he said lighter but he must have realized your dealing with gas and tried to renig... It's ok to make a mistake and tell people to blow themselves up.
if he was serious- he would have deleted the entire joke !