Grom Power Commander V Autotune Installation Video PART 1 - Great Low Prices
ฝัง
- เผยแพร่เมื่อ 6 ก.พ. 2025
- Please be sure to watch our UPDATED WBC2 INSTALL VIDEO: • WATCH THIS VIDEO Honda...
→ CHECK OUT our website : www.hardracing....
Installing a Dyno Jet Power Commander V & Autotune on Honda Grom Project Bike.
UPDATE:
We have found it works much better to Run the Red POWER Wire to the FI Fuse next to the battery...... , instead of tapping off the Tail Light.
It's a better power source for the Autotune, & WBC2.
See photo here: www.hardracing....
Also, make sure you Ground BOTH BLACK Wires on the WBC2.
Great Low Prices
→ Subscribe : www.youtube.com...
→ Please take a second to leave a comment before you head off.
→ Facebook: / hardracingllc
→ Twitter: / hardracing_com
→ Instagram: / hardracing
.
#HardRacing #GromPCV #GromPowerCommander #GromPowerCommanderV #GromDJPCV #GromWBC #GromWBC2 #GromWideBand
UPDATE:
We have found it works much better to Run the Red POWER Wire to the FI Fuse next to the battery...... , instead of tapping off the Tail Light.
It's a better power source for the Autotune, & WBC2.
See photo here: www.hondagrom.net/forums/attachments/11521d1402683027-dynojet-pcv-wideband-2-newb-guide-wb2_power.jpg
@Hudson Nasir Excellent.
Also, make sure you Ground BOTH BLACK Wires on the WBC2.
Hello, if I go with the finbro ported super head with the flat head piston, and bigger throttle body intake and manifold set up with custom exhaust CAN I ONLY USE THE PCV BY ITSELF? OR I NEED TO BUY THE AUTO TUNE AS WELL? THANKS!
The power commander is plug and play but what specific map did it have? U didn’t elaborate on the specific default map the unit had before installing it, can you elaborate more on this, did u download it specifically from Dyno site or do you guys sell the Dyno unit preloaded for a 2017 Grom with high air flow k&n filter intake M4 full exhaust? Thx!
What is a good starting point (set up ) for the accelerator pump function ; rpm, % fuel added, throttle % open etc ?
Is it possible to just run in the WB O2 sensor into the stock spot on the engine?
Where is the best place to put the PCV box on the SF series with ABS after relocating the tip sensor?
hey great video, btw i had problems with my autotune, it keep blinking after the engine running and it shows afr 9,99 i also had the problems of installing both black and red wire, black to negative side of terminal right, but i can't seem to find brake light wire, any idea where too plug the posi lock? it so tight space at rear, ninja 300 here, cheers
I have 17 Grom with the PCV and autotune. Do I need to disconnect stock o2 sensor? Just cut the wire and leave the sensor in? Please advise
Can you just put the power and ground in the powercomander
Hi you didn’t specify if the Dyno commander comes preloaded with default mapping for the bike you installed it on or did you have to download from site before hand ? I want to buy for my 2017 Grom which has a high air flow K&N filter and M4 full exhaust will you guys preload it with the mapping for my specific needs so I can simply install it right out the box from HR?
Yes we offer Custom maps that a customer can request after the place their order with our company for the PCV.
@@HardRacingPerformanc cool I will call the order in then and specify my standard needs, save me the trouble downloading app and mapping the unit thx!
Do you also need to use the ZFI with this, to get the best performance?
after install power commander and auto tune is need to go to the computer to set up if I only put commander and auto tune and don't tune up in computer the bike will run ? the auto tune will do the job for me?
Yes, It is recommended to follow the instructions and setup the PCV with the software. But you don't have to if you don't want to.
The bike will still run.
The pcv can use in msx 125 2013 the computer is the same?
I just bought a 2017 Honda Grom. I removed the snorkels, replaced the stock air filter with a K&N air filter, added the velocity stack, and added a full zoom exhaust. Do you think I need a PCV? If I did get it, would I just have to pull it out of the package, plug it in and ride away?
It will definitely, help the bike run more efficient A/F Ratio..... add a little more power, and improve acceleration.
so once I buy it, do i just install it and it's done, or do i have to program it somehow to my setup?
If you watch our videos it will explain everything.
Hi.Can you tell me if I should be remove the factory o2 sensor or should I keep both?
Regards from Italy.
Great video.
I have a question about the autotune. I currently have the Yoshimura and airpod filter map installed on my Power Commander after installing a 181 kit (along with: Upgraded cam chain tensioner, Koso throttle body, air intake, fuel injector, chimera/k&n filter, oil pump, and oil cooler), but it bogs down when it passes a high rpm (~6k)
So once I install an auto tune do I have to make any adjustments to the current map or is it just plug and play?
Thanks.
Great video. I have a question about the auto tune. I currently have the yoshimura and AirPod filter map installed on my power commander after installing a 181 bbk (along with upgraded cam chain tensioner, koso throttle body, air intake, fuel injector, chimera/k&n filter, oil pump, and oil cooler) but it starts to bog down once it hits ~6k rpm.
So once I install an auto tune do I have to make any adjustments to the map or does the auto tune take care of everything (Plug and play type of thing)?
Thanks!
SO do you have to cut a hole in the exhuast to fit the new o2 sensor?
Correct.
The only way to mount the O2 sensor on your exhaust, is to drill a hole and have your local welder, or muffler shop weld it on.
They usually only charge like $25-$30
Great video.. besides been a power commander V can I know the especific numer or how can i get the same one?
not sure what you mean ?
Would it be best to get rid of the stock o2 sensor like how you did with using the WB2?
You can. We replaced ours with a plug.
Is there any specific location the O2 sensor bung needs to be welded on the exhaust?
Most customers install it within 6-10 Inches of the exhaust port.
Very important that it's angled upward at least 15^ so no condensation gets in the plug.
I want to get the pcv...but I don't see a map for my setup...mnnthbx exhaust and intake...I see they have yosh full and pod filter would that be good to go?Because the pcv is a million times easier than the bazzaz to install
+Ronald Campos
No worries.
Upon customer request... we can preload the map before shipping it to you.
That way it's plug-n-play.
Awesome!!! So it woukd be a map for the mnnthbx exhaust and intake then?
Did this wake up the bike I might be ordering one soon, you guys have the best prices. Do you have maps for the air box mod and mnnthbx exhaust?
HUGE Wakeup. Specially when we switched from Autotune, to the DJ WBC2.
Sent you an email on maps.
I have the yashimura full exhaust on my 2017 honda grom and no other mods, will the PCV only have any performance effect and will it worth the money ?
Libertiner, yes the PCV will help improve the performance of your bike.
I just purchased the PCV and the auto tune for my 06 R1 (haven't installed it yet... still need to find a way to weld the O2 sensor since i don't have a welder) is this going to give me a good increase and is the auto tune going to build a map that gives me best/max performance?
oh yea. It definitely, helps make the bike run better... smoother.. more efficient.
So it basically creates a map itself to give the bike the best performance?
ryan carter Exactly.
As shown in the Video above...... once you set the parameters....... then it will do the rest
Can I run the power commander v in the newer model grom? I can only find it advertised for the 2014-2015 model
You mean the Grom SF ?
+HardRacing yeah that's it. it's a 2016 model sold in Australia
Would this work on honda Pcx PgmFi scooter? I run 170 Takegawa with 150 head, 250rr cam , 35mm tb, pod and exhaust...
Plugs are same as grom...
Unfortunately, it will not.
Sorry
Brian, we sent you a reply.
Thanks man. Appreciate the help! Keep the videos coming ✋
how come after i installed pcv and auto tuner, my brand new battery keeps dying?
are these still for sale as it wont let my buy it from your website keeps on saying This site is not secure
In stock and on sale.
If you hare having issue ordering online, you can also just call in the phone order.
hi i am from the UK
Please send us an email directly to our sales dept.
They will get you taken care of.
How can I installe the O2 sensor in the yoshimura RS2
You just drill a hole and weld the bung on there.
Hey there Hard Racing team i wanted to know if i would need to change the spark plug after installing a cold air intake, a full exhaust system (Two Brothers) and the Power Commander V and what ECU resets should i do after all that?
You can if you like. go down 1 temp rating on the plug.
I want buy the commander,auto tune and lcd display but in your website can not send to my to my place why? Macao (CHINA)
please send us email, we will get you PCV.
Is there anyone in SoCal that can help me do this?
may I ask why install any mods on a grom?
Because it's dirt slow without mods.
Is the Autotune necessary if I am just changing exhaust and air intake? Is it easy to change the fuel/air ratio with just the power commader on its own?
You can just purchase and use the PCV alone, if you prefer.
Many Grom owners have done the same.
I couldn’t see 🤷🏻♂️
it's there.