I just wanna say thanks for all your videos! Yesterday my Ps5 controller started to stick drift and I ended up switching out the potentiometer from a working donor board. I used all the tips and tricks i learned from your channel and the controller is now fixed. I have tried to do that in the past and messed up badly. Thanks to your channel, I was able to get back to gaming. I also saved the world from complaints by getting rid of the messy solder. It is now better than factory!
I have been in the electronic repair business since the early 90's repairing mainly TV's, VCR's and so on, I still repair LED TV's today, your soldering skills and diagnostics skills are insane, LOVE you videos, from Melbourne in Australia... keep up the great work.
Alex you mentioned a viewer talking about using IPA on the ultrasonic machine, let me tell you something it works awesome, yes you are correct it's flammable so use at your own risk.
I get up at 5:00 am central time for my coffee fix and Northridge fix and never disappointed! Wouldn't mind to see some of big boss teardowns and reassembling. Thanks 😊
We used to use Closed cycle IPA UltraSonic cleaning baths with a refrigerated top condensing fume capture at a Military PCB production factory back in the mid 1980's. we could clean boards upto 50cm wide. They are nice bits of kit, but are expensive, so not suitable for a small business.
Thank you for sharing your knowledge. But, Alex. The A3* chip you changed should be a mosfet driver/controller. The one you looked up is a dual LDO linear regulator.
The chip is actually a NCP81151MNTBG, but he is right about both A3H & A37 being the same chip; the first two digits are the product code, the third one is the date code
@@frenkie0902 That's just the outer case covering the chip. It helps to dissipate heat and protects the chip fom UV light and physical damage. The chip itself is most likely fine
It's fair. You fixed it and there was an underlying problem. Took a week to show. It's not feasible for you to test every device for 2 weeks. It all works out, nice job 👍
Yea man u seem legit my ps5 been doin good so far but recently had a hdmi problem were it came on but was saying no signal on tv I messed with it a bit it came bk on eventually worried its early signs of my hdmi connectors going out nice to see u in Cali as I am Atwell will be sure to hit u if need to fix my stuff
Good job. Glad you're not getting a lot of repeat repairs under warranty, it kind of proves your methodology works. Which is reassuring for all the component level repair people out here (myself included).
how do electronic components short out ? why does it short out ? what cause it short out ? a big fan of you watching every single video you upload . pls mention my question in the video or just reply to my comment . love your content because i like your personality .
@NorthridgeFix Its not enough for the laptop to be on, you need to stress test for 15 mins to make sure that chip doesnt blow out again when under heavy load.
I just noticed that after 12:50 the audio and video are way off. You are talking about the PDF of the documentation of that chip you replaced while you were showing that the laptop was working. And your intro played while you were still talking about it. Also the timeline on YT ended but still kept going so for the last like 20 seconds there is just a black screen. I don't think as it's my YT bugging out as it persisted after a page refresh. It isn't video-breaking but could you please fix this? Other than that I really like what you do and I still find it amazing how quickly you can fix devices with your knowledge!
"The customer paid for expedited service when he brought it in so we're still going to give him expedited service to re-do his laptop." Puts a rush on a warranty. Not something you see very often. That right there is quality customer service. You're the man Alex.
I just wanna say thanks for all your videos! Your soldering skills and diagnostics skills are incredible. I think about to change my business, but I have to watch more vids of you. ;-)
kind of epic, i had a acer aspire motherboard with the very same issue. thought, it took me a darn 4-5 weeks to shove my face to the controller chip. Good work, nice that you knew of the issue. i didn't
I think big boss's job is REALLY amazing, it takes a lot of patience to dissemble an reassemble electronic devices. If you you wanna verify this, try to teardown a laptop...or a smartphone... BIG UP BIG BOSS !
I've experienced the same/similar on digital commercial tape drives in the 80s in manufacturing in Monrovia, CA. Usually the output power devices will blow and replacement of the output transistors of the preamp will resolve the issue. In a few cases, uncommon, the pre-stage drivers of this preamp to these output transistors on this same board will also blow. The tape drives are soaked for 2 weeks, drives will usually fail well within this soak environmental test. Most common are the power transistors of the power amp, a separate circuit board with a huge heatsink. The TO3 transistors will blow probably because of an imbalance. Sometimes this will damage the output of the preamp board. Virtually all failures are power related for power supplies, controls, sensors and tape drives. Seldom does a logic (chip) fail (probably less than 1% of all failures) because back in the day things were comparatively conservative. Today chips and near components do fail, consumer goods, because they are basically overdriven or overclocked. It was a time when virtually any schematic, pictorial diagram or perhaps theory of operation could be had for any product. The days when Heathkit and others like it were still around.
While it is not best practice it's actually a very common thing among smokeing culture to clean different bowl pieces etc with ever clear in an untrasonic cleaner and it does magic even being flammable
Another great video, Wish I was local I am currently in Philippines but i have a MSI ge72mvr 7rg the motherboard popped a mosfet as well. Love your videos Merry Christmas and GOD bless
Keep us updated, if it comes back again please. By the way, I've asked many times the title of the outro tune, if you don't want to say, could you at least extend one of your videos to include the full track?
Well crap.. I recently got an Asus laptop but it's a ProArt. At least Alex is getting alot of business from failed Asus laptops and with any luck he will have enough experience with them to find a surefire way to fix many of them. But I have a feeling it's sadly a case of cheap components causing the failures or even worse flaws in the motherboard. The parts shortage is a good excuse for companies as well I suppose..
i would absolutely advice against using IPA in an ultrasonic cleaner. this is used in a very controlled environment and not for the common person. it is a highly effective way for cleaning but it is very dangerous.. stay away from it if you do not know what you are doing. do not do this at home.
Alex you are sooo right on Weller getting extremely overpriced. Yes, Weller stuff ist still the professionals "wet dream" kind of tool, but as its so overpriced and not affordable - people should try to get better value/money relation from other manufacturers.
why does it feel like Asus is slipping in the laptop department. I had a friend who brought me his Asus ROG Zephyrus S15 GX502GV and it was running so hot, temps are at 100°C+ on load. All pads have melted and on one side of the VRM, the pads are not even making contact. A good set of high end pads and TIM lowered that by 20°C.
It always makes me wonder, how are you sure that there isn't a solder bridge under a chip when you squeeze it out at last heating? Is the surface tension enough to make them break apart under the chip? If the blobs flow out then there must be more than enough under to cause bridging. I'm always scared of making a short in this way, but I'm curious of your methods and pardon my ignorance if it was already answered in other videos :) I love seeing your skills and how happy you are when stuff is fixed!
there are chips with a large soldering point (ground) in the middle, where this must be done, other chips with many small connections must not be pressed under any circumstances.
This video is just the answer to the question of a certain commentator, why you should replace the mosfets in pairs and the driver. They should be replaced so that laptops do not return for a complaint.
I have a question. I can see the use for a zero ohm resistor when you need to hop over another trace on the board, but what is a zero ohm resistor's purpose when not hopping over another trace?
Some mosfets may require a bit more gate driver resistance to dampen risetime and ringing. Usually not more than a couple of ohms. I guess they leave them in to keep the flexibility of changing parts, just in case.
My Asus G731G just broke, two months after the warranty expires. It just popped and went dark. I will never buy Asus laptop again. Never. This was last problem. In two years, there has been plenty of other problems.
What is the white almost like a light salt crust on some Parts of this board, similar as you see on a sailboat after being at sea for a short trip and getting sprayed by waves?? Ps thanks for the interesting video's that show your work
Chip makers take the purest silicon crystals and make them work by introducing intentional defects. It's amazing they work at all but even more amazing is what has been driving the development all these years ... our desire to play games. Thanks for all your videos Alex. You are a true Jedi Knight with a soldering iron
Absolutely unrecommended to use ipa in an ultrasonic. Some people do it (Kingpin from EVGA for example), but even he doesn't recommend that you follow his lead, it is dangerous.
Hi! This is from Google: "Zero ohm resistors are the perfect remedy to 'magically' route a single layer board. Rather than making holes and turning the PCB into a double-layer structure, you can route a trace between the pads of a zero ohm resistor. These resistors are then assembled along with other components during the manufacturing process."
You didn't add "boss of all bosses", at the end, after you said "thank you big boss"!! Or was this video maybe made BEFORE you had started saying both phrases together? 🤔
do not dry the ipa with a dry stick, u will leave fibers all over. After cleaning with ipa, u can blow the remaining ipa away with hot air (100 C). It will look better.
well that's because there is still some flux residue left behind and it becomes sticky. if you keep on cleaning 2-3 times the spot there will be no fibers left. but i understand there is not a problem if just a little flux is left over, even from the factory sometimes it has on laptop motherboards (near solder jumpers etc)
Im just so scared.. I just started working on laptop for work from home and the motherboard just got . Oh god.. This is so scary.. So unexpecting.. How am i going to work.. I've given for servicing and i dont even have extended warranty
Hi there.. I am one of your subscriber always watching from PHILIPPINES 🇵🇭🇵🇭😊😊BTW merry Christmas to you and to your family .. If you don't mind how can I message you personally coz I have to ask questions personally
How is an ultrasonic machine meant to ignite IPA? It only uses vibration and sound waves to cause cavitation. The only risk is the formation of vapour but used in a well ventilated area it's fine.
Ultrasonic machines has heaters that can be set to specific temperatures. Not only vibrations. Inhaling fumes is a health hazard in addition to IPA being flammable. Cleaning solution exist that does a similar or better job without the risks.
@NorthridgeFix but it's electrically isolated from the liquid to prevent short circuit so there's no risk of a spark and doesn't get close to the temperature required for IPA to auto-ignite, which is 399⁰C.
Search google and take it from there. Just because someone used IPA and nothing happened doesn't make it right, like a 90 year old smoker who tells you smoking did not harm him does not make cigarettes safe.
asus are known to fail they are constructed out of low grade parts ive had several tablets that stopped working & ive realised its cheaper to buy a new one than it is to repair & all parts are interchangeable
I noticed a blue silicone work pad at the @13:04 time mark in the video ..... That one is bigger than the one in the web store..... I have the one that's in the web store .....But I can't find the larger ones ...... Are they available here ???
The world is full of haters, they will comment about the 7nd h between the friendship XD 🤪 I don't have a clue what you are doing, but is just a pleasure watching u work ! keep up the good work ( beeter than factory) ! peace ✌️
that ending is out of sync, maybe youtube uploading/processing acting weird
TH-cam messed it up as always when I tried to post edit in TH-cam editor. Video is still processing after 10 hours. I contacted TH-cam to fix
@@NorthridgeFix thanks boss
@@NorthridgeFix : Wait, wasn't that the asus laptop with the liquid metal spillage? If so, it might return again.
Looks like TH-cam fixed it.
I just wanna say thanks for all your videos! Yesterday my Ps5 controller started to stick drift and I ended up switching out the potentiometer from a working donor board. I used all the tips and tricks i learned from your channel and the controller is now fixed. I have tried to do that in the past and messed up badly. Thanks to your channel, I was able to get back to gaming. I also saved the world from complaints by getting rid of the messy solder. It is now better than factory!
Its refreshing to see a business honor their warranty than make up some bs excuses. I respect this channel even more
Nice to see great customer service and stand behind their work !!
The ultrasonic and IPA, is actually a way to clean some aircraft parts. I work as an airforce tech and we do it often
Yep warms up quick too - with no heater
what is ipa a beer?
@@aljosakrojac9085 haha, well it is, but we're talking isopropyl alcohol
What aircraft parts would you clean in an ultrasonic cleaner with IPA?
I have been in the electronic repair business since the early 90's repairing mainly TV's, VCR's and so on, I still repair LED TV's today, your soldering skills and diagnostics skills are insane, LOVE you videos, from Melbourne in Australia... keep up the great work.
Alex you mentioned a viewer talking about using IPA on the ultrasonic machine, let me tell you something it works awesome, yes you are correct it's flammable so use at your own risk.
I get up at 5:00 am central time for my coffee fix and Northridge fix and never disappointed! Wouldn't mind to see some of big boss teardowns and reassembling. Thanks 😊
5:00am no thanks😵😵😵😂😂
Good job, Alex. Great to see you stand by your warranty, even when the unexpected (repair return) happens.
We used to use Closed cycle IPA UltraSonic cleaning baths with a refrigerated top condensing fume capture at a Military PCB production factory back in the mid 1980's. we could clean boards upto 50cm wide. They are nice bits of kit, but are expensive, so not suitable for a small business.
Alex, it nice to see you stand behind your work and give him expedited service.👍👍👍
Thank you for sharing your knowledge. But, Alex. The A3* chip you changed should be a mosfet driver/controller. The one you looked up is a dual LDO linear regulator.
It's the same chip, call it whatever you want
The chip is actually a NCP81151MNTBG, but he is right about both A3H & A37 being the same chip; the first two digits are the product code, the third one is the date code
@@NorthridgeFix I am a bit woried because A3H chip was little bit damaged on top left
@@frenkie0902 That's just the outer case covering the chip. It helps to dissipate heat and protects the chip fom UV light and physical damage. The chip itself is most likely fine
Yes, you are right. I discovered the same thing.
It's fair. You fixed it and there was an underlying problem. Took a week to show. It's not feasible for you to test every device for 2 weeks. It all works out, nice job 👍
Yea man u seem legit my ps5 been doin good so far but recently had a hdmi problem were it came on but was saying no signal on tv I messed with it a bit it came bk on eventually worried its early signs of my hdmi connectors going out nice to see u in Cali as I am Atwell will be sure to hit u if need to fix my stuff
Now that's service, Another fantastic fix. If i lived in the US i would ONLY go to this shop for repairs! :)
Alex: we fixed that board.
Asus: I'm back bro.
Good job. Glad you're not getting a lot of repeat repairs under warranty, it kind of proves your methodology works. Which is reassuring for all the component level repair people out here (myself included).
how do electronic components short out ? why does it short out ? what cause it short out ? a big fan of you watching every single video you upload . pls mention my question in the video or just reply to my comment . love your content because i like your personality .
@NorthridgeFix Its not enough for the laptop to be on, you need to stress test for 15 mins to make sure that chip doesnt blow out again when under heavy load.
I just noticed that after 12:50 the audio and video are way off. You are talking about the PDF of the documentation of that chip you replaced while you were showing that the laptop was working. And your intro played while you were still talking about it. Also the timeline on YT ended but still kept going so for the last like 20 seconds there is just a black screen. I don't think as it's my YT bugging out as it persisted after a page refresh. It isn't video-breaking but could you please fix this? Other than that I really like what you do and I still find it amazing how quickly you can fix devices with your knowledge!
Check pinned comment
"The customer paid for expedited service when he brought it in so we're still going to give him expedited service to re-do his laptop." Puts a rush on a warranty. Not something you see very often. That right there is quality customer service. You're the man Alex.
I just wanna say thanks for all your videos! Your soldering skills and diagnostics skills are incredible. I think about to change my business, but I have to watch more vids of you. ;-)
We want more videos in a day from you... 😊
Respect the man who fixes the impossible. Love the videos.
Great job bro 🎉
But for more safety you can ask the customer to bring charger also and check, could be faulty charger
kind of epic, i had a acer aspire motherboard with the very same issue. thought, it took me a darn 4-5 weeks to shove my face to the controller chip. Good work, nice that you knew of the issue. i didn't
I think big boss's job is REALLY amazing, it takes a lot of patience to dissemble an reassemble electronic devices.
If you you wanna verify this, try to teardown a laptop...or a smartphone...
BIG UP BIG BOSS !
I've experienced the same/similar on digital commercial tape drives in the 80s in manufacturing in Monrovia, CA. Usually the output power devices will blow and replacement of the output transistors of the preamp will resolve the issue. In a few cases, uncommon, the pre-stage drivers of this preamp to these output transistors on this same board will also blow. The tape drives are soaked for 2 weeks, drives will usually fail well within this soak environmental test. Most common are the power transistors of the power amp, a separate circuit board with a huge heatsink. The TO3 transistors will blow probably because of an imbalance. Sometimes this will damage the output of the preamp board.
Virtually all failures are power related for power supplies, controls, sensors and tape drives. Seldom does a logic (chip) fail (probably less than 1% of all failures) because back in the day things were comparatively conservative. Today chips and near components do fail, consumer goods, because they are basically overdriven or overclocked.
It was a time when virtually any schematic, pictorial diagram or perhaps theory of operation could be had for any product. The days when Heathkit and others like it were still around.
I'm going to have to learn how to look up IC numbers and find the associated data sheets.
I'm actually STUPID interested in the difference between A3T, A3H, and A37. like how are you not at least going to tell us where to look it up? lmao
I'm feeling scared to buy an Asus laptop after watching there are lots of motherboard issues.
You should be. Forget laptops. Get a desktop.
I have an Asus laptop and I do not recommend it at all. Everything about it is bad
Almost all their devices have had issues. I remember the previous zenfones getting bootlocked for no reason.
Not practical or economical to fix a desktop motherboard.
My asus laptop monitor died in 2 years
The A37 and A3H are likely OnSemi NCP81151 MOSFET drivers. The "A3" is the real marking the last letter is month of production, so it doesn't matter.
While it is not best practice it's actually a very common thing among smokeing culture to clean different bowl pieces etc with ever clear in an untrasonic cleaner and it does magic even being flammable
Another great video, Wish I was local I am currently in Philippines but i have a MSI ge72mvr 7rg the motherboard popped a mosfet as well. Love your videos Merry Christmas and GOD bless
Keep us updated, if it comes back again please. By the way, I've asked many times the title of the outro tune, if you don't want to say, could you at least extend one of your videos to include the full track?
Well crap.. I recently got an Asus laptop but it's a ProArt. At least Alex is getting alot of business from failed Asus laptops and with any luck he will have enough experience with them to find a surefire way to fix many of them. But I have a feeling it's sadly a case of cheap components causing the failures or even worse flaws in the motherboard. The parts shortage is a good excuse for companies as well I suppose..
Amazing and interesting work. Great video, thx. Happy xmas to all of you in the shop. Have nice holidays with your family. Greets
I have used an Antex $20 soldering iron for about 10 years. Rarely needs tip changing.
Keep up the great work happy new year 🎉
Ultrasonic in IPA and even acetone is common in some industries. Just don't use heaters. Not unsafe. That said I don't ultrasonic populated boards.
You're the man wish the best for you and your family.
I use IPA in my ultrasonic cleaner all the time to clean resin 3d prints, it's what works best. I don't use the heating function though.
Great viewing thankyou.
It's always good to put all repaired PC on stress test maybe for 1 hour, before shipping to customer.
Keep us posted on this job
Man, ASUS really cheaps out on power management. Almost got an ASUS laptop in April but decided to pay a bit more for Sager. Thank freaking god...
i would absolutely advice against using IPA in an ultrasonic cleaner. this is used in a very controlled environment and not for the common person. it is a highly effective way for cleaning but it is very dangerous.. stay away from it if you do not know what you are doing. do not do this at home.
Uve got a new sub here.. Like ur vids.. Keep it up👍
Alex you are sooo right on Weller getting extremely overpriced.
Yes, Weller stuff ist still the professionals "wet dream" kind of tool, but as its so overpriced and not affordable - people should try to get better value/money relation from other manufacturers.
I'm sure there are a lot of pros also watching these videos though. I just don't think they're the majority, is what I mean.
why does it feel like Asus is slipping in the laptop department. I had a friend who brought me his Asus ROG Zephyrus S15 GX502GV and it was running so hot, temps are at 100°C+ on load. All pads have melted and on one side of the VRM, the pads are not even making contact. A good set of high end pads and TIM lowered that by 20°C.
It always makes me wonder, how are you sure that there isn't a solder bridge under a chip when you squeeze it out at last heating? Is the surface tension enough to make them break apart under the chip? If the blobs flow out then there must be more than enough under to cause bridging. I'm always scared of making a short in this way, but I'm curious of your methods and pardon my ignorance if it was already answered in other videos :) I love seeing your skills and how happy you are when stuff is fixed!
there are chips with a large soldering point (ground) in the middle, where this must be done, other chips with many small connections must not be pressed under any circumstances.
I can't help but wonder too
Alex said in recent video, that enough amount of flux will effectively protect from shorts underneath.
@@digitalk68 yeah flux is your friend that always helping you
i understand your english so easily
Thank you Alex ❤
This video is just the answer to the question of a certain commentator, why you should replace the mosfets in pairs and the driver. They should be replaced so that laptops do not return for a complaint.
I have a question. I can see the use for a zero ohm resistor when you need to hop over another trace on the board, but what is a zero ohm resistor's purpose when not hopping over another trace?
Could possibily be used as a fuse
Some mosfets may require a bit more gate driver resistance to dampen risetime and ringing. Usually not more than a couple of ohms. I guess they leave them in to keep the flexibility of changing parts, just in case.
i hope you the best buddy keep it up .
My Asus G731G just broke, two months after the warranty expires. It just popped and went dark. I will never buy Asus laptop again. Never. This was last problem. In two years, there has been plenty of other problems.
Btw have you thought on buying a ultrassonic machine for cleaning boards?
What is the white almost like a light salt crust on some
Parts of this board, similar as you see on a sailboat after being at sea for a short trip and getting sprayed by waves?? Ps thanks for the interesting video's that show your work
The video finish like 40 secs before the audio... weird thing. Still a good useful video thank you.
معلم يعطيك العافية ، سؤال سريع: محطة اللحام الصينية اللي بتستخدمها بتنصح فيها مقارنة بالHakko 951؟ تقريباً نفس السعر.
2:47 Phenomenal service right there.
Chip makers take the purest silicon crystals and make them work by introducing intentional defects. It's amazing they work at all but even more amazing is what has been driving the development all these years ... our desire to play games. Thanks for all your videos Alex. You are a true Jedi Knight with a soldering iron
Be the Force with him for ever...😀😀😀
A pure ingredient does not a cake make. Or a chip, for that matter.
That board view at 4:00 shows a lot of "muck" over the board. Do you clean such boards, as the dirt could cause short-circuits and strange behaviour.
Absolutely unrecommended to use ipa in an ultrasonic. Some people do it (Kingpin from EVGA for example), but even he doesn't recommend that you follow his lead, it is dangerous.
Common sense is such a rare commodity. I thank God that my father was very hard on me and showed me common sense every minute of every day.
Great video.... Like always.. 👍
very honest re do under warranty
saving the world from complaints, one video at a time
You just don’t run the ultrasonic w/ heat when using alcohol. It’s a very common practice.
Hi, what is the purpose of the zero ohm resistors in this instance?
Hi! This is from Google:
"Zero ohm resistors are the perfect remedy to 'magically' route a single layer board. Rather than making holes and turning the PCB into a double-layer structure, you can route a trace between the pads of a zero ohm resistor. These resistors are then assembled along with other components during the manufacturing process."
They are used as "jumpers" to route traces over other traces on the same layer
@@Exarhadsgfds yeah but i dont see a trace going under the resistor so i thought maybe there is another reason
Came back for same problem.
So where do you get your donor boards from? Do you buy them? Leftovers from no fixes?
You didn't add "boss of all bosses", at the end, after you said "thank you big boss"!!
Or was this video maybe made BEFORE you had started saying both phrases together? 🤔
do not dry the ipa with a dry stick, u will leave fibers all over. After cleaning with ipa, u can blow the remaining ipa away with hot air (100 C). It will look better.
well that's because there is still some flux residue left behind and it becomes sticky. if you keep on cleaning 2-3 times the spot there will be no fibers left. but i understand there is not a problem if just a little flux is left over, even from the factory sometimes it has on laptop motherboards (near solder jumpers etc)
good customer care full marks
Im just so scared.. I just started working on laptop for work from home and the motherboard just got . Oh god.. This is so scary.. So unexpecting.. How am i going to work.. I've given for servicing and i dont even have extended warranty
Does the T3B soldering station come with soldering tweezers or are they available?
any upcoming episodes on the house hunt?
T3D is incompatible with hot tweezers. so it does not really compare with the Weller, right?
Hi there.. I am one of your subscriber always watching from PHILIPPINES 🇵🇭🇵🇭😊😊BTW merry Christmas to you and to your family .. If you don't mind how can I message you personally coz I have to ask questions personally
How is an ultrasonic machine meant to ignite IPA? It only uses vibration and sound waves to cause cavitation. The only risk is the formation of vapour but used in a well ventilated area it's fine.
Ultrasonic machines has heaters that can be set to specific temperatures. Not only vibrations. Inhaling fumes is a health hazard in addition to IPA being flammable. Cleaning solution exist that does a similar or better job without the risks.
@NorthridgeFix but it's electrically isolated from the liquid to prevent short circuit so there's no risk of a spark and doesn't get close to the temperature required for IPA to auto-ignite, which is 399⁰C.
Search google and take it from there. Just because someone used IPA and nothing happened doesn't make it right, like a 90 year old smoker who tells you smoking did not harm him does not make cigarettes safe.
asus are known to fail they are constructed out of low grade parts ive had several tablets that stopped working & ive realised its cheaper to buy a new one than it is to repair & all parts are interchangeable
That laptop was filthy, you don't clean the laptops as part of your service? I always return anything I work on completely clean.
Maybe a stupid question, but why do they use zero ohm resistors? It is a renowned company like Asus, so you'd not expect these or?
I like this guy , he’s good at what he does . Can you hire me ? Maybe I can sweep the floors or something
Was i? About the ultra Sonic?
Hope not, cuz to remove vaseline from motherboards after NL2 OC on motherboards works very good.
Some things are just not worth working on and Asus laptops is one of them things In life
I noticed a blue silicone work pad at the @13:04 time mark in the video ..... That one is bigger than the one in the web store..... I have the one that's in the web store .....But I can't find the larger ones ...... Are they available here ???
I think asking "why?" would have prevented the rework.
ultrasonic with ipa works just fine
imagine if big boss had an assembling channel also, super cool
Right to repair in action. Of course you'll need several years of experience and the right equipment, but it is still possible.
It's a shame that a company that makes such amazing computer hardware fails in terms of component durability.
If you haven't noticed, there is a HUGE component shortage on the market. Beggars can't be choosers.
nice repair
Great double check, next time you can check 10 minutes on power mode.
Considering you have replaced the chip a few times already, you sure do leave next to no damage even under microscope !
i like your point of view ;)
Superb😊
The world is full of haters, they will comment about the 7nd h between the friendship XD 🤪 I don't have a clue what you are doing, but is just a pleasure watching u work ! keep up the good work ( beeter than factory) ! peace ✌️
Good job !
Do you repair circuit boards for GTO gate operators?