It’s very close to the motor, but since the bracket wraps around the tubular frame, you should have some play to get everything roughed in before tightening the bolts.
The Can-Am Audio Roof requires the 400 Watt amplifier to drive the subwoofer, otherwise you would only have around 25 Watts from the source unit driving the sub. In the outdoor environment using that low of power would not create the level of bass you'll need to hear it properly. You can find more information on the subwoofer and amplifier for the Can-Am Audio Roof here: rockfordfosgate.com/products/system/utv-audio/2020-can-am-maverick-x3/
is the power wire at 9:13 already in the canam itself or is it in the kit because i have the connecter the power wire but im not sure where to connect it
Yes, this is the Can-Am ACCESSORY TURN-ON wire. If you're having problems locating it, have one person stand in front of the Can-Am. Have the 2nd person inside the UTV lift up on the dash. The 1st person in front should be able to see the red wire and identify its location.
The BLUE wire from the main amplifier wiring harness connects to the BLUE wire from the PMX source unit harness. You'll see the BLUE wire at 8:14 on the main power harness and at 9:04.
Yes, at timecode 10:44 in the above video, Greg explains "Start with the Driver Panel and reattach the SmartLok harness. Be sure to push in the red locking pin. The reattach the headlight [switch] and any accessory switches you have." We suggest to take a photo with your mobile device to help with any reconnection of harnesses.
I just installed this system. Everything plug and play, i have one issue. My volume is really low. I turn the volume knob to 40 and its sounds like if it was like a 8 instead. Can it be an issue with the reciver?
So it sounds like the output is very, very low. Be sure the RCA’s are fully inserted at the back of the radio. You also want to double check ALL connections at the amp. Be sure EVERY wire is fully seated in the Molex connectors. We have seen a couple installs where 1 wire pulled out of the input or output molex. Did you make any adjustments to the amplifier controls? You may want to verify the PRESET = ON.
You're upgrading from M1 series speakers on an 800W amplifier to M2 series speakers on a 1,500W amplifier. You can find more details on the models included with stage-4 & stage-5 at: rockfordfosgate.com/products/details/x317-stg4/
The STG4 kit requires the subwoofer to be plugged into the REAR outputs of the amplifier. If you're having trouble, please contact our support specialists at 1-800-669-9899 Mon-Fri 8am-5pm for real-time troubleshooting assistance.
This is an extremely rare situation. We've had our dealer network accumulate hundreds of installations without issue. Many Can-Am dealers do this as part of service since the power steering on this car is sensitive, so UTVs that don’t have an audio system installed can still benefit from this reset. We have the documentation for the reset available here: rftech.custhelp.com/app/answers/detail/a_id/1374/kw/can-am
Hi Edith, the X317-STG4 is equipped with the PMX-RGB, an LED controller. We have a walk-thru on adjusting your Color Optix™ lights here: th-cam.com/video/k2wr5si8J7Q/w-d-xo.html
It's hard to find, and it isn't accessible by looking up under the dash. Have someone inside the vehicle pull up on the dash panel while you stand in front of the vehicle and look in with a flashlight. You'll see a red wire attached to the top of the subframe.
This STG4 kit requires the subwoofer to be plugged into the REAR outputs of the amplifier. If you're having trouble, please contact our support agents at 1-800-669-9899 Mon-Fri 8am-5pm for real-time troubleshooting assistance.
Is the amp suppose to fit tight. Mine seems to be hitting the steering wheel motor.
It’s very close to the motor, but since the bracket wraps around the tubular frame, you should have some play to get everything roughed in before tightening the bolts.
Kinda off topic, I have the audio roof and was wondering can I connect a sub to this without adding a amp? Thanks
The Can-Am Audio Roof requires the 400 Watt amplifier to drive the subwoofer, otherwise you would only have around 25 Watts from the source unit driving the sub. In the outdoor environment using that low of power would not create the level of bass you'll need to hear it properly. You can find more information on the subwoofer and amplifier for the Can-Am Audio Roof here: rockfordfosgate.com/products/system/utv-audio/2020-can-am-maverick-x3/
Can you mount the seats in the lower position with the subwoofer?
Yes, Absolutely! Our subwoofer enclosures allow full vertical travel of the seat for proper adjustment.
@@rockfordfosgate can you make a separate video on how this is done? It doesn’t seem possible with the included brackets
@@michaelcutrona2009 Take out the front seat bolts, put it in the lower position on the frame, then replace the bolts.
is the power wire at 9:13 already in the canam itself or is it in the kit because i have the connecter the power wire but im not sure where to connect it
Yes, this is the Can-Am ACCESSORY TURN-ON wire. If you're having problems locating it, have one person stand in front of the Can-Am. Have the 2nd person inside the UTV lift up on the dash. The 1st person in front should be able to see the red wire and identify its location.
How do I locate the power wire under the center dash? Thank you
The BLUE wire from the main amplifier wiring harness connects to the BLUE wire from the PMX source unit harness. You'll see the BLUE wire at 8:14 on the main power harness and at 9:04.
We are almost done!!! Lol just need to figure out the blue remote wire
Installing mine now. What do y’all do with the power outlet that’s going to be behind the pmx unit?? Ty
On our demo vehicles we don't use them, but technically, you can create an extension -to- panel mount USB charger for the dash.
I’m assuming you reconnect the smart lock connections back in the same way you disconnected it?
Yes, at timecode 10:44 in the above video, Greg explains "Start with the Driver Panel and reattach the SmartLok harness. Be sure to push in the red locking pin. The reattach the headlight [switch] and any accessory switches you have." We suggest to take a photo with your mobile device to help with any reconnection of harnesses.
@@rockfordfosgate thank you I appreciate it.
I just installed this system. Everything plug and play, i have one issue. My volume is really low. I turn the volume knob to 40 and its sounds like if it was like a 8 instead. Can it be an issue with the reciver?
So it sounds like the output is very, very low. Be sure the RCA’s are fully inserted at the back of the radio. You also want to double check ALL connections at the amp. Be sure EVERY wire is fully seated in the Molex connectors. We have seen a couple installs where 1 wire pulled out of the input or output molex.
Did you make any adjustments to the amplifier controls? You may want to verify the PRESET = ON.
Is it compatible with can am x3 2023 RS TURBO RR four seater max?
The kit is compatible with the 2022 Maverick X3 MAX rs Tubro RR 72, so it will fit the 2023 model too.
@@rockfordfosgate awesome appreciate the reply!
What’s the difference between stage 4 and 5
You're upgrading from M1 series speakers on an 800W amplifier to M2 series speakers on a 1,500W amplifier. You can find more details on the models included with stage-4 & stage-5 at: rockfordfosgate.com/products/details/x317-stg4/
My subwoofer it’s working I already tried to connect and disconnect but nothing
The STG4 kit requires the subwoofer to be plugged into the REAR outputs of the amplifier. If you're having trouble, please contact our support specialists at 1-800-669-9899 Mon-Fri 8am-5pm for real-time troubleshooting assistance.
Did you guys get that dynamic steering issue fix or figured out?
This is an extremely rare situation. We've had our dealer network accumulate hundreds of installations without issue. Many Can-Am dealers do this as part of service since the power steering on this car is sensitive, so UTVs that don’t have an audio system installed can still benefit from this reset. We have the documentation for the reset available here: rftech.custhelp.com/app/answers/detail/a_id/1374/kw/can-am
@@rockfordfosgate
Right on I'm waiting on my x3 max Ds turbo and want that stage 4 system in mines!!!
How do you turn the lights on the speakers?
Hi Edith, the X317-STG4 is equipped with the PMX-RGB, an LED controller. We have a walk-thru on adjusting your Color Optix™ lights here: th-cam.com/video/k2wr5si8J7Q/w-d-xo.html
How do I find the power wire at 9:13?
It's hard to find, and it isn't accessible by looking up under the dash. Have someone inside the vehicle pull up on the dash panel while you stand in front of the vehicle and look in with a flashlight. You'll see a red wire attached to the top of the subframe.
PRODUCT DETAILS
rockfordfosgate.com/products/details/x317-stg4/
My subwoofer is not working. I dont know the issue
Did you ever figure it out? Im having issues wiring up the amo
@@davidq4489 I just unplugged the wires for all the speakers and plugged them back. It works now.
This STG4 kit requires the subwoofer to be plugged into the REAR outputs of the amplifier. If you're having trouble, please contact our support agents at 1-800-669-9899 Mon-Fri 8am-5pm for real-time troubleshooting assistance.
You guys completely skipped how to wire up the 12 pin connector
Installation of the 12-pin harness from the dash to the PMX source unit is shown here: th-cam.com/video/p_M6fXq7WdU/w-d-xo.html