Bought a house in October 2020 with about 1.1 acres. Had never even been on a ride on before. Found this channel and all of the information has been incredible. I purchased this exact tractor; 2021 S240. Your video made me very confident in the purchase and all relevant maintenance. This channel needs to get more publicity because its much more well done than any of the others including John Deere's own videos. Great work.
I have question about fuel. Can I put Ethanol free gasoline? I use it on most of my equipment, but I want to be sure if it ok for this tractor. Thank you
Your in depth videos make me more confident in John Deere and getting this mower. Very well done videos that cover all my questions more effectively than any dealer I’ve been to.
Been using the mower for a year. Going strong, enjoy using it. I did finally get and install the bagger. Bagger instructions were not very good but I figured it out. Highly recommend this mower.
I just bought one of these machines after having another John Deere for 18 years. The controls were different, and your video help helped us substantially. Thanks.
Just ordered an s240. Tired of working on my Troy bike pony that was my grandpa’s. Thank you for doing these videos! They were so helpful when deciding
Just put my order in for a S240 with 42 inch deck at my local dealer! I appreciate the videos very informative and helped me with my decision of what to purchase! Keep up the good work Brent 👍 PS if I need additional attachments down the road I will check your site out!
Another fantastic video. I am going to purchase this mower after watching your very thorough video. I’m so glad I found your channel. My favorite part of watching this is that when I go to purchase, I am already prepared with the features of this mower. Fantastic job
Just wanted to thank you for all your video reviews of the 100 and 200 series models. I was originally considering an S160 until I saw your videos and then decided that the S170 would be a better choice for me. Unfortunately no one in my area up here in Maine had ANY in stock including the local John Deere dealer. They did however have an S180 yesterday so today I stopped in to check it out only to find that it had sold. That's when I first heard of the S240. With the Kawasaki engine, the 48 inch deck (the 54 was more than I wanted anyway) and the other general upgrades with this model I made the deal. Your videos were a great introduction to the John Deere lawn tractor world and a huge help in my selection process to finally purchase the right one. Thank you!
Brent, you are the best. Thank you so much for the insightful and thorough review. You articulated everything in an easy to understand manner, which I really appreciate. I purchased the S240 42 inch deck from Ag-Pro last week and it was delivered this morning. In Georgia, there were only 2 remaining, so I was relieved that I was able to get my hands on one. Looking forward to my first cut with it tomorrow!
What a GREAT VIDEO!! I learned so much from you guys! And Brett is a wonderful speaker, not one Uh, or Um . That means he really knows his Schlick!! Keep up the great work!!!👍👍🙏🏼❤️
After 20 years of good service my Sabre with a Briggs Intek has given it’s all. Ordered the S240 due to Kawasaki and upgraded trans. Wish the trans was serviceable though.
@@davidboyd7494 technically you can service a k46. You'll have to remove the shifter and brake connectors and then remove the transmission. There's a filter kit you can buy along with fresh fluid. Theres a fill cap that must be removed from the top of the transmission to drain and fill it. Once its drained flip it bottom up and remove the pan on the bottom. Theres a couple magnets thatll need cleaned off and a paper filter to change. Clean the mating surfaces of the pan and transmission well and apply a high quality rtv sealant and bolt back the pieces. Fill with fluid and before reinstalling the fill cap rotate the input drive shaft for a minute in each direction to purge any air. Check fluid level again. It should be 3/4" from the top. Reinstall fill cap and transmission. In roughly 2 hours you can service the unserviceable.
I have an old L120 I was looking to replace. I initially thought I wanted the S130 but after watching this video I have decided to go with the S240. The main reasons for me: better engine and oil change (EZ oil change just not for me), 3 year warranty, separate throttle and choke, separate position for lights on only when needed. Thanks for educating me on this model. My mower will be purchased from my local dealer but was "sold" by Western Equipment! Any chance of getting some decals for the sides of my hood? :-)
I am so glad I could help you with this decision. If you can email me at brent@west-equip.com I will see what I can so on getting you some decals. Thank you and thanks for watching!
Hi there! First of all, thank you very much for this video! I just bought a S240 second hand, but I’m having a hard time to find out which Bagger Kit I should buy for this model. I’ve seen one model that comes with a different chute, but it’s over 1200 dollars. Do you know which bagger kit would work with this 48-inch deck? Thank you!
Thank you sir for this informative video. This has helped me become confident in purchasing this model and I will say once I got my tractor I felt comfortable since I watched this video. I love my grass and I was tired of push mowing for hours. I was looking into the electric but nothing is better then the legend John Deer. This tractor is more than I expected. I’m definitely a John Deer fan. Thank you for your great videos. If I have questions I will definitely ask you sir.
Just bought one of these today with the 48 inch deck. Unfortunately, the John Deere/AgriVision didn't have any set up. So I couldn't take it home today. Was really wanting to rip through my yard. 😂. But, when it shows, after watching these tutorials, I feel more than able to just jump on and go. Great material! I didn't ask when at the store though. How easy is the deck removal process?
Well hopefully they will get on it soon. It is pretty simple. Here is a good example of how yours should be th-cam.com/video/434Mz3k5FGc/w-d-xo.html. I hope this helps and thanks for watching!
Bought a 2023 s240 with the 42” deck. Spring in the electric clutch busted after 5 hours of use. Dealer took 5 weeks to repair it. Also a warning to anyone looking for a bagger to install yourself: JD changed the deck, so s240 baggers aren’t 1 model fits all. Yellow decks get one model, green ones get a different one. Brent’s video is great…for the yellow decks. Had to follow the IKEA level instructions for the green deck since there aren’t any videos for those installations. You’re almost better off looking at parts, looking at the deck, and figuring it out yourself.
Purchased s240 last year. Purchased rear bagger in September 2021 and it still has not arrived… is your dealership having supply issues with John Deer? My dealer has gotten two in but no more. What’s the problem with JD!?!?
How often do you grease - how many hours? Also, I have an old L130 and looking to upgrade to this mower along with a a mulching deck. You can get this with a 48" mulching deck, correct? Any issues with the mulching deck?
Initially you want to grease after 8 hours and then every 25 hours after that. and there is not an actually mulching deck but there are mulching attachments for the decks and we have really good luck with them.
Excellent review, thank you. Your thoughts S180 or S240 48” for 2 Acres flat property? Also, reliability of the ELS engine. Nervous about the ELS verse the Kawasaki. Thank you in advance!
Thank you and honestly it all depends on your desired cutting width. If you feel as though you need the 54" the S180 is a good choice. The thing I like about the S240 is the deck build on the 48" deck. It is a more high capacity deck even though it isn't as wide as the 54" on the S180. Both are great mowers and I have mowed with both of them. I hope this helps and thanks for watching!
Excellent video and thanks for the links I’ll be ordering S240 48” in the next two weeks from my local dealer. The heavier gauge deck on the 48” than the 42” sold me to go with the 48”. Thanks again for all the info
@@WesternEquipment I noticed in the specs on the S240 previous years j Deere had FS Kawasaki engine in their mower but the 2021 model they went with the FR engine isnt that a step down?
the previous year S240 had the Tuff Torq K46 transaxle, but this year John Deere advertises it as K46 Heavy Duty. Is there a change to this year's K46? Does it have a more sturdy build or a higher torque rating than the previous year? I looked on the John Deere and Tuff Torq websites but they don't say if there's a change in specs.
Hi Brent was wondering if you might be able to help me with something, purchased a 2020 s240 got about 10 hours on the machine and the gas tank gauge does not work , is there a simple fix that I can do myself I am good with wrenches thanks.
So the gas tank is a floating tank that sits on an arm that runs your float gauge. It could be a couple of different things. Either that arm that goes from the gauge to the underside of the tank is broken or your tank may have springs that help hold it in place and one of them may be broken. I wouldn't sat this is a simple fix just because of how much disassembling will have to be done. But those would be the issue cause the gauge not to work. I hope this helps and thanks for watching!
Question. I am comparing this model with a s170. But what gives me pause is why does the s240 have smaller rear wheels and an engine with less horsepower than a s170?
Great Review. Got my S240 earlier this week and love it. Been watching your videos ever since I got it. Two questions though. 1.) Is the bagger system the same for 2020 - 2021 S240's? Your parts store only lists one option for it so I just want to make sure? Thank You.
Great video. Do you think you could do an S220 vs S240 video? I bought the S220, mainly because the dealer had some on order and I needed it quick. I'd love to know what I gave up.
Seat cover should fix you up on the seat and as far as filling the tank a like fo use an extended funnel to avoid the mess. I hope this helps and thanks for watching!
A question: the grease fittings on the spindles , are the bearings sealed or open to except grease ? The older decks on J D ‘s were sealed bearings and the grease never got into the bearings! Same thing on the new ones ?
Yes they are sealed but it is important to make sure you grease your spindles to make sure to keep moisture from building inside and possibly damaging the shaft. Great question and thanks for watching!
I have an L120. Whats the biggest engine i can put on it. My 22 hp briggs is running on 1 cylinder. Or is there something i can pit in it to free up the second cylinder
Just got my S240 with the 42 inch deck and am looking forward to grass cutting season with my 3 lots of land instead of my self propelled Toro. Side discharge is fine for me through the mowing season, and I don't want to drop the money on the mulch kit and blades and would like a mulch plug option for the leaves in the fall with the Accel Deep Mower Deck. Otherwise I will be tempted to use my 22 inch Toro Recycler with the mulch option for all my yard in the fall.
Unfortunately on the Accel Deep deck the mulch control kit is the only option. You might be able to fabricate something as a cover over the opening to accomplish the leaf mulching. Thanks for watching!
Can I get 2021 S240 42inch mulch control system and baggers from your digital store? It dispenses lots of clippings outside. Lawn looks messy after mowing. Any suggestions please.
Unfortunately both of these items are unavailable from John Deere right now due to manufacturing delays. We are hoping this resolves soon. Thanks for watching!
My wife and I are in our early to mid 60’s and looking at buying a new John Deere s240, or x330, 42” deck, Kawasaki engine (locating one has been difficult due to Covid). We have about 1 1/4 acres mostly flat ground with a few trees. Your videos are helpful and informative in making an initial purchase decision, and service afterwards. Thanks, we appreciate it! Wilbur & Loyce, North Florida
@@WesternEquipment just one quick follow up, do you think the x330 would be worth the additional $600 over the s240 for our use? 1 1/4 acre Mowing, Bagging, pulling a cart, fertilize spreader, and possibly thatcher attachment? Thanks again! Wilbur
@@wilburreeves8329 theyve got the same engine and transmission, and even the same tires. The deck lift and height adjustment along with the x330 having a somewhat heavier frame are the most notable differences. I think the x330 has a longer warranty also. I mow about almost 2 acres currently using a honda hrx217 pushmower and cub cadet ltx1040 42" tractor. I have to mow rather slow to achieve a decent cut with it,so I'm looking to upgrade. I think the s240 would suit my needs ok,because I dont have any steep hills or substantial obstacles and seldom tow anything.
Hi Brent. Thanks for your excellent videos. They've helped me to decide on the S240 with a 42" deck. I'd like to find out if you agree with that choice or if the 48" deck would be better. I plan to mulch about 1.5 acres of flat as well as somewhat sloped and rough terrain at a height of around 3.5". A shorter cutting time with the larger deck is not an important consideration. I picked the lighter deck so it's easier to adjust the cutting height and remove it for service, less expensive to add a bagger and to maintain 2 vs 3 blades / spindles, easier to fit the tractor on a 5 ft wide trailer and because it should be more maneuverable on slopes. I'd be grateful if you could answer a few questions. Does the MulchControl kit work equally well on both decks or are the results better on one of them? Would a well maintained 42" stamped deck be as rust resistant as a 10 gauge forged 48" deck? Is there less risk of damaging a blade / spindle on sloped rough terrain with the additional 2 gauge wheels of the 48" deck or more risk due to the greater width? Which deck would you recommend for this lawn? Thanks very much for your help.
All great question. To start, yes, I would go with the 42" deck. The mulch control works well on both models and there is no advantage in rust protection with the thicker steal. there is going to be less risk of damage with the shorter deck and I would definitely recommend the 42" deck for your specific situation. I hope this helps and thanks for watching!
@@WesternEquipment Thanks very much for your time Brent to answer my questions. I really appreciate the help to confirm that an S240 with a 42" deck is a good choice for this lawn. Take care and have a great day!
I wanna do some yard mowing for my neighborhood, they are 1 acre or just a bit more, what would be the model in the s100 or 200 series? Or a good used model? Thanks
Any of the 100 or 200 series models would be great, even in the used models. Main thing you need to decide is what size of deck you need to get in and out of gates if you have that issue. Good question and thanks for watching!
Great review, as always! I picked my 2021 S240 up about a month ago, so far so good. I was concerned about the fuel filter physically touching the engine, so I used a zip tie to pull it closer to the battery by wrapping it around the fuel line and the battery strap. It has done a good job keeping the filter off the engine. Also, any clue when part # BUC11053 will be available? I'd love to get mulching, but I haven't seen the mulch control kit attachment in stock. Thanks again!
That sounds like a good idea! And I wish I could give you an estimated stock date on that kit but I do not know and we have been trying to get info for a while now. There have been tons of inventory issues with most major vendors so we are all hoping this gets resolved quickly. Thank you for watching!
Yes, some earlier model lawn tractors did not have the twin hydrostatic pedals. Let me know if I can help with anything else on this machine is you purchase it and thanks for watching!
Curious on the oil change with the new fr651v that has the 2.2 quart oil capacity. Will the purchase of 2 quarts be enough due to residual oil that may stay in the engine, or should a partial small amount from a third quart be required? Oil change kits are still showing just 2 quarts. Also, this is my first kawasaki engine. Is it normal for them to require topping off the oil alot? Are they oil burners?
Usually 2 quarts does the job and I have not experienced them being oil burners and have not heard that from our service departments either. Good questions and thanks for watching!
Thank you sir. Your very informative videos have helped me to sift through a lot of info very quickly. I have ordered my S240 in 42" deck with a Mulch kit. Very excited and can't wait to get it in
I don't have the mulch kit on mine and I'm noticing that the engine is so powerful that you don't really notice the clippings on the lawn. I wouldn't be concerned unless you are doing it commercially or you are having a party/event and you don't want clippings brought in, which are also greatly reduced due to the Kawasaki engine when compared to my push mowers and previous rider.
Thank you! Yes, it is good for mulching and bagging. Being that it is a smaller deck and processing less material than a larger deck makes it good for both of these applications. Thanks for watching!
Just wondering if you can guess why JD stopped offering the freedom 42 deck? I own a 20 year old LT 160 with the freedom mulching deck, the deck mulches perfectly only had to replace the timing belt once in all the time I owned it. I have a new s240 with the 42 deep cut deck on order from the local JD green store, they said might be in by mid June but they can't say when the mulch kit will be in. I'm still cutting with the LT but the Kohler is burning oil under load almost to the point of "hope the neighbors don't call the EPA on me while I'm cutting" mode.
I honestly do not know why they discontinued the freedom deck. I have heard numerous times how well they work. The mulching kits have been an issue to get for a while now so I am hoping this gets resolved soon. Thanks for watching!
I just got this mower & it’s awesome. To one of your points, when it’s time to replace the fuel filter, I’ll remove the battery to gain much needed space. Have a question regarding the primary deck belt. On you video, with blades engaged, the section of belt going to the far left spindle runs smooth. On mine, kind of flops around a lot. My dealer said it is normal. Any remedies? Thanks.
Glad you are enjoying it! you may need to see if there is some adjustment you can make to one of your idler pulleys to take out the slack. You don't want it too tight but there shouldn't be any flop when running your blades either. I hope this helps and thanks for watching!
The points shown will be the only true lubrication points and the spindles should be done every 8 hours and the front axle should be done every 25 hours. Good questions and thanks for watching!
What I have always liked about my Craftsman is the ability to mow in reverse without making any additional actions. One lever for choke and throttle combined. Start the mower , reposition the start key to a reverse position and mow in in forward reverse anytime. My reverse is with a handle similar to the deck lever and my hand is always on it. Quick and simple. I don’t need two foot pedals nor an extra button for reverse. J-D has too many buttons and levers. That’s not a high end sports car you have there, it’s just a grass cutter.
You've got the same cvt transmission my old cub cadet has. It's good as long as you dont have alot of obstacles when you're mowing,but if you have to change direction alot a hydrostatic tranny allows alot quicker transition. I will agree that I'm not a fan of john Deere's mow in reverse feature,but the s 240s loaded with high quality features and the deck is second to none. The best selling feature is john Deere's impressive customer service after the sale. Craftsman service is no longer available and you'll not find any stocked parts. Independent shops will work on them,but you wont be a priority and you'll be waiting on parts being ordered. I'll stick with john deere or cub cadet when I get a new mower.
The reverse switch is very easy to by-pass, took all of 5 minutes. I had a mower with the handle for forward and reverse and liked it until I got this one, now I much prefer the foot pedals.
buying our first new riding mower in 20 years. My dad and I were surprised. Mowers today are more complicated for no reason, not to mention more expensive. Back then the one we got was 900 bucks and all metal. The S130 we were looking at is $2800 and is half plastic. So many buttons and features that are gonna break in time. That digital gas reader, parking brake button, cruise control?? lol And we asked that too, why is it so complicated to mow in reverse? On the old mower all those buttons and extra pedal were basically in one lever, and mowing in reverse wasn't something you put extra thought into, it's a basic thing. Not sure why it's like this either like you said it's just to cut the grass. But i'm guessing like anything else, it's so they can charge you more and they put all this extra flimsy crap cause they don't want you to have it for years and years. They want it to break so you to run out and buy another.
I got this same 2021 S240 model with a 42” Accel deep. What begging kit is recommended? I have been told I need a special one that isn’t manufactured yet by a JD dealer but I believe they are blowing smoke because everything is back ordered. Thank you!
The one you need is a BUC10907 and from what I see it is still not available. John Deere has been having inventory issues, but we are hoping to see them resolve soon. Sorry for the inconvenience, but thanks for watching!
They have not stopped producing them but there is currently a shortage of parts and materials so building some machines have been difficult for John Deere. Hoping this issue gets resolved soon. Thanks for watching!
Looking at purchasing new lawn tractor! Been looking @ S240 with 48 deck & X350 with 48 deck. I think I noticed there are differences in these 2 decks! Looks to me 48 inch deck on the X350 has easier adjust scalp wheels as well as swivel scalp wheels for easier deck removal? Also is the deck thickness the same on both 48 deck on S240 & the 48 inch deck on the X350?
Yes, you got it! The anti scalping wheels are better for deck removal on the X350 but the gauge of steel on either model is the same. Good questions and thanks for watching!
Hi Brent just passing through and saw this video. Great video very informative.We are the manufacturers of the Kavli Blades and make mower blades for the John Deere. I think you would be very surprised at what these mowers are capable of with our blades.
The retail price as of early 2021 was around $2899 and the transmission is a Tuff Torq K46. Prices may vary depending on location and with 2022 models coming soon. I hope this helped and thanks for watching!
INTERESTING QUESTION FOR "WESTERN EQUIPMENT" ABOUT THE NEW S240; YOU MAY NOT BE ABLE TO ANSWER THIS BUT,... WHY DID JOHN DEERE DUE AWAY WITH ALL THE HEAT VENTS ON BOTH SIDES OF THE ENGINE HOOD EXCEPT FOR ONE SMALL SLOT IN THE TOP CENTER,..? EXCEPT FOR THE FRONT GRILL AREA IT SEEMS LIKE SINCE HEAT RISES,..THERE WOULD BE EVEN MORE HEAT BUILD-UP WITH LESS HEAT VENTING OR DISPERSION ABOVE AND IN THE ENGINE AREA.
I wish I knew the answer to this. John Deere seems to like to change up their styling designs often so I'm assuming this on one of those type of things.
@@WesternEquipment THIS NEW HOOD DESIGN IS IN ITS 2nd YEAR I BELIEVE,... HOPEFULLY THEY KNOW WHAT THEIR DOING,..? I'LL KNOW BETTER MYSELF ABOUT THE HEAT ISSUE WHEN MINE ARRIVES IN A COUPLE OF WEEKS.
It's a good idea to change to the mulching blades because they have a longer cutting surface that will help to mulch the grass finer. Good question and thanks for watching!
There are parts availability issues worldwide. From what I have heard there is just a shortage of raw materials and also a lack of transportation to get parts and materials to manufacturers. I'm hoping it gets resolved soon. Thanks for watching!
hi brent i just bought a new s130 and it was missing a spindle cover would that be under warranty ive already contacted and made case with john deere so im tryin to get that cover its rh spindle cover,and ive heard lot people had that happen to,ok later brent
Sounds like you have gone through the proper channels to get your issue resolved and yes this has been happening a lot and I'm not sure why. Let me know what happens and thanks for watching!
@@WesternEquipment hi brent I got update from john deere case and they sent me a diagram and parts list for the s130 42 deck and said there was no part only a cover over the lh spindle is shown on the diagram and parts list so I guess there was no cover after all but I'm thinking maybe the lh cover will fit the side ok have a good one brent.
hi Brent they corrected my case and now there is a spindle cover for the s130 john deere tractor mower, part number GY21773,it is if your veiwers need one to,for the 42"edge deck,they said will send me one out asap,so hope resolved soon sorry to bother you with my problems but it was just a missing part that i didnt get,ok good videos Brent ill be watching,later brent
Thanks man! The video is great, been looking for a new lawn tractor did a ton of research and decided on the 240, with the 48", the case iron front axel, 10 gauge steel mower and the engine really sold me. Love the capabilities and upgrades from the 100 vs the 240 model. This video really took me over edge to purchase.
Just received my mower from a local dealer with the mulch control kit installed. very nice. QQ on the Bluetooth module (BUC10929), my dealer has attempted to order this part several times, Deere cancels the order even though they show 150 in stock. The dealer speculates Deere is holding onto these for the new units which I find curious because I purchased mine new. Have you had a similar experience?
Yes, we have had issues getting this part and are still waiting on a response as to when it will be fully released. I wish I had more help on this topic. I am wanting to get one to so that I can do a video on it. Hopefully it will be resolved soon. Thanks for watching!
anybody buying one of these check up on the center of the front axle, if they still put a grease zirk there make sure it gets greased frequently. If the bushings don't wear the axle does causing the front tires to tow out horribly causing it to steer very hard. Keep it greased and no problem. I've replaced front axles on several of these 100 series JD mowers. Other then that these are good econo/quality mowers. Former Tech.
Haha, well I have a very small yard in town so I actually used to use a John Deere SB14 until it finally gave up on me. I now use a Honda self propelled HRN216VYA. Once I move and have more area to mow I will get a John Deere zero turn and maybe I'll even show it off in a video! Thanks for watching!
Thanks for your great videos and the way you answer questions! I just used my new 2021 S240 with bagging option and it worked great. I have a question regarding addition of a mulch control unit. Is part BUC10704 the correct part? Also, I read that you can use the mulch control and bagging system simultaneously resulting in partial bagging and partial mulching; is this correct? If so, what blades (bagging or mulching) would be best for this operation? Thanks again!
Yes, that is the correct number for the mulch control kit for a 42" deck. I'm not sure about using them at the same time as I have not seen that combo, but if so then I would use a standard 3-in-1 blade. I hope this helps and thanks for watching!
@@WesternEquipment thanks! But now I'm confused; I just saw that a Deere representative said on the Home Depot site that the correct mulch kit part number is
Just bought a new S240 and a few days after the 1st mow, I found 5 random areas of dead grass in the lawn and after the second mow on Saturday, there are 4 more patches. They look like fuel burns and I’m guessing it’s coming from the mower. Anyone experience this before? I will be calling the JD dealer tomorrow. Thanks
@@WesternEquipment thanks - dealer insisted it’s not the mower so I push mowed this weekend and waiting to see if any new spots appear. If not, I will mow with the JD on Wednesday and then see if any new spots appear. Dealer thinks it’s either stray dogs or rabbits doing the damage so we’ll see.
I had the same thing happen I found it’s where you stop and sit at full throttle it burned the grass. If I stop now I lower the throttle haven’t seen any since
@@cambellschunky704 not yet. I have been researching a while. I sat on a X370 the other day. I must say the seat was really comfortable compared to the one on the S240 and X350.
@@steve9377 The X series is a class above the base S class so I'm not surprised about the comfort. X3 vs X5 may is a model difference as well as the next number. The last number is an engine designation. I am leaning towards a Kawasaki motor. Is there a reason you have not considered a zero turn? I would like one, but my elderly mother may have trouble with those controls.
@@cambellschunky704 I’ve driven a zero turn a few times, I hated it. I’ll choose a steering wheel and pedals every time. Weird thing about the seat is once you get into the X500 series it goes back to the not as comfortable seat. A Kawasaki engine is a requirement for me. I wish John Deere would openly say it has a Briggs or Kawasaki engine instead of trying to mask it under the Cyclonic or iTorque names.
The biggest advantage is the additional frame size and strength. Then there are various smaller advantage such as an upgraded display panel and more attachment options. I hope this helps and thanks for watching!
@@SwapnilBhartiya as of right now the order in features of John Deere mowers go from the series (the ones shown in Lowe’s etc, and goes from s100 to s180) then goes the s series but the s240 which is right in the middle in between the s and x series. The x series have a lot more features to choose from but cost more.
@@manofculture4945 Ditto. S240 has same engine and other features in x350 except may be the steel is a few mm thicker in x350 pls one extra year of warantee. So I am not sure if $1000 is worth given I am just a home users with 17000 sq to cut. In most cases there is huge difference in quality and sustainability but at this point i am a bit confused.
@@manofculture4945 I’m looking to buy a used tractor for my fist season them buying a new one because plowing can be rough to get customers the first year so I just need to see how many people I can get before I have to shell at 1500$ on a lawn tractor
![[Gegagedigedagedago] NEW Help Gegagedigedagedago Nugget escape from Nikocado Avocado Challenge](http://i.ytimg.com/vi/hJWnwRC2Fz8/mqdefault.jpg)
Bought a house in October 2020 with about 1.1 acres. Had never even been on a ride on before. Found this channel and all of the information has been incredible. I purchased this exact tractor; 2021 S240. Your video made me very confident in the purchase and all relevant maintenance. This channel needs to get more publicity because its much more well done than any of the others including John Deere's own videos. Great work.
Awesome! I'm glad I could help you make your decision. Thanks for the comment and thanks for watching!
I have question about fuel. Can I put Ethanol free gasoline? I use it on most of my equipment, but I want to be sure if it ok for this tractor. Thank you
@@jasonsm123 absolutely the best thing to use. Itll run on either, but ethanol is harder on carburetors and rubber parts like fuel lines
I love your responders McDonald’s
S130 2022 8 hours used it has always vibrated when blades are not engaged what could it be
One of the best mower videos I've ever seen. EXCELLENT.
Your in depth videos make me more confident in John Deere and getting this mower. Very well done videos that cover all my questions more effectively than any dealer I’ve been to.
Wow, tanks for the compliment. I'm glad I could help and thanks for watching!
Been using the mower for a year. Going strong, enjoy using it. I did finally get and install the bagger. Bagger instructions were not very good but I figured it out. Highly recommend this mower.
@@FactoryDogs😊
I ordered a 2021 s240 from local John Deere dealer here in Sussex New Brunswick. Should be in later this month. You videos are great thanks!
Awesome! I hope you really enjoy your mower and thanks for watching!
I just bought one of these machines after having another John Deere for 18 years. The controls were different, and your video help helped us substantially. Thanks.
Well I am glad I could help and I hope you are enjoying your mower! Thanks for watching!
I just ordered the s 240 and this video is a great guide for me! Outstanding video! THANKS!
Just ordered an s240. Tired of working on my Troy bike pony that was my grandpa’s. Thank you for doing these videos! They were so helpful when deciding
Well I am glad I can help you make your decision. Thanks for watching!
Thanks for the overview! Helped me decide to order one from my local John Deere dealer today!
Awesome! I hope you enjoy it and I'm glad I could help with your decision. Thanks for watching!
Just purchased mine a month ago. I did a lot of interenets searching. The 48" with mulch kit is such a great combination.
Awesome! I hope you're enjoying your mower and thanks for watching!
I have a 2023 S-240 with a 42” deck being delivered tomorrow. Bagger was delivered by ups today. Hoping I made the right decision.
Just put my order in for a S240 with 42 inch deck at my local dealer! I appreciate the videos very informative and helped me with my decision of what to purchase! Keep up the good work Brent 👍
PS if I need additional attachments down the road I will check your site out!
Awesome, I hope you really like it! Thanks for watching and i hope we can help you with those needs in the future!
How ya liking it?
@@machoman5356 very pleased with it! No complaints whatsoever
Another fantastic video. I am going to purchase this mower after watching your very thorough video. I’m so glad I found your channel.
My favorite part of watching this is that when I go to purchase, I am already prepared with the features of this mower. Fantastic job
I am glad I could help and thanks for watching!
Just wanted to thank you for all your video reviews of the 100 and 200 series models. I was originally considering an S160 until I saw your videos and then decided that the S170 would be a better choice for me. Unfortunately no one in my area up here in Maine had ANY in stock including the local John Deere dealer. They did however have an S180 yesterday so today I stopped in to check it out only to find that it had sold.
That's when I first heard of the S240. With the Kawasaki engine, the 48 inch deck (the 54 was more than I wanted anyway) and the other general upgrades with this model I made the deal.
Your videos were a great introduction to the John Deere lawn tractor world and a huge help in my selection process to finally purchase the right one. Thank you!
I am glad I could help and thanks for watching! So did you already get your S240?
Anyone else think that he looks an awful lot like Al (Richard Karn) from the old Home Improvement TV show?
Excellent video!
Thank you and I'm taking this as a full on compliment haha! Thanks for watching!
Brent, you are the best. Thank you so much for the insightful and thorough review. You articulated everything in an easy to understand manner, which I really appreciate. I purchased the S240 42 inch deck from Ag-Pro last week and it was delivered this morning. In Georgia, there were only 2 remaining, so I was relieved that I was able to get my hands on one. Looking forward to my first cut with it tomorrow!
Thank you so much! Congrats on your new mower and thanks for watching!
What a GREAT VIDEO!! I learned so much from you guys! And Brett is a wonderful speaker, not one Uh, or Um . That means he really knows his Schlick!!
Keep up the great work!!!👍👍🙏🏼❤️
Great video Brent! Lots of great information as always! Love your bloopers outtakes! Thanks for sharing! Have a great and awesome day!
Thanks for always watching our videos Vincent! I'm glad you enjoyed it!
Great video! Just picked up an S240 and it was just what I needed to get going with it.
Thank you and I hope you enjoy it. Thanks for watching!
After 20 years of good service my Sabre with a Briggs Intek has given it’s all. Ordered the S240 due to Kawasaki and upgraded trans. Wish the trans was serviceable though.
I hope you enjoy your new mower and thanks for watching!
Completed my first mow. It could use more power. Is there a turbo kit available for that Kawasaki? Maybe I’ll have to rewire it.
@@davidboyd7494 technically you can service a k46. You'll have to remove the shifter and brake connectors and then remove the transmission. There's a filter kit you can buy along with fresh fluid. Theres a fill cap that must be removed from the top of the transmission to drain and fill it. Once its drained flip it bottom up and remove the pan on the bottom. Theres a couple magnets thatll need cleaned off and a paper filter to change. Clean the mating surfaces of the pan and transmission well and apply a high quality rtv sealant and bolt back the pieces. Fill with fluid and before reinstalling the fill cap rotate the input drive shaft for a minute in each direction to purge any air. Check fluid level again. It should be 3/4" from the top. Reinstall fill cap and transmission. In roughly 2 hours you can service the unserviceable.
I have an old L120 I was looking to replace. I initially thought I wanted the S130 but after watching this video I have decided to go with the S240. The main reasons for me: better engine and oil change (EZ oil change just not for me), 3 year warranty, separate throttle and choke, separate position for lights on only when needed. Thanks for educating me on this model. My mower will be purchased from my local dealer but was "sold" by Western Equipment! Any chance of getting some decals for the sides of my hood? :-)
I am so glad I could help you with this decision. If you can email me at brent@west-equip.com I will see what I can so on getting you some decals. Thank you and thanks for watching!
helpful mention regarding accessibility. I have bad left leg so this was helpful to mention.
Well, I hate to hear that, but I'm glad the mention was useful for you!
Hi there! First of all, thank you very much for this video! I just bought a S240 second hand, but I’m having a hard time to find out which Bagger Kit I should buy for this model. I’ve seen one model that comes with a different chute, but it’s over 1200 dollars. Do you know which bagger kit would work with this 48-inch deck? Thank you!
Thank you sir for this informative video. This has helped me become confident in purchasing this model and I will say once I got my tractor I felt comfortable since I watched this video. I love my grass and I was tired of push mowing for hours. I was looking into the electric but nothing is better then the legend John Deer. This tractor is more than I expected. I’m definitely a John Deer fan. Thank you for your great videos. If I have questions I will definitely ask you sir.
Awesome! I am glad I could help and thanks for watching!
Just bought one of these today with the 48 inch deck. Unfortunately, the John Deere/AgriVision didn't have any set up. So I couldn't take it home today. Was really wanting to rip through my yard. 😂. But, when it shows, after watching these tutorials, I feel more than able to just jump on and go.
Great material!
I didn't ask when at the store though. How easy is the deck removal process?
Well hopefully they will get on it soon. It is pretty simple. Here is a good example of how yours should be th-cam.com/video/434Mz3k5FGc/w-d-xo.html. I hope this helps and thanks for watching!
Bought a 2023 s240 with the 42” deck. Spring in the electric clutch busted after 5 hours of use. Dealer took 5 weeks to repair it. Also a warning to anyone looking for a bagger to install yourself: JD changed the deck, so s240 baggers aren’t 1 model fits all. Yellow decks get one model, green ones get a different one. Brent’s video is great…for the yellow decks. Had to follow the IKEA level instructions for the green deck since there aren’t any videos for those installations. You’re almost better off looking at parts, looking at the deck, and figuring it out yourself.
Purchased s240 last year. Purchased rear bagger in September 2021 and it still has not arrived… is your dealership having supply issues with John Deer? My dealer has gotten two in but no more. What’s the problem with JD!?!?
Yes, unfortunately parts availability is still an issue. Hoping this gets resolved soon. Thanks for watching!
How often do you grease - how many hours? Also, I have an old L130 and looking to upgrade to this mower along with a a mulching deck. You can get this with a 48" mulching deck, correct? Any issues with the mulching deck?
Initially you want to grease after 8 hours and then every 25 hours after that. and there is not an actually mulching deck but there are mulching attachments for the decks and we have really good luck with them.
I’m just curious why I should buy this over the S170 with the bigger tires which I have a very rough yard, so that would make things a little easier
Excellent review, thank you. Your thoughts S180 or S240 48” for 2 Acres flat property? Also, reliability of the ELS engine. Nervous about the ELS verse the Kawasaki. Thank you in advance!
Thank you and honestly it all depends on your desired cutting width. If you feel as though you need the 54" the S180 is a good choice. The thing I like about the S240 is the deck build on the 48" deck. It is a more high capacity deck even though it isn't as wide as the 54" on the S180. Both are great mowers and I have mowed with both of them. I hope this helps and thanks for watching!
Excellent video and thanks for the links I’ll be ordering S240 48” in the next two weeks from my local dealer. The heavier gauge deck on the 48” than the 42” sold me to go with the 48”. Thanks again for all the info
Thank you and I'm glad I could help. Thanks for watching!
@@WesternEquipment I noticed in the specs on the S240 previous years j Deere had FS Kawasaki engine in their mower but the 2021 model they went with the FR engine isnt that a step down?
@@gordo4559 it is...they did it on some x3xx series also. Its pretty disappointing. I was going to get an x370 but now ill probably just get the s240.
RIO switch and seat safety switch "duct tape bypass mod" are my first modifications made on my last 3 john deere mowers 🤷♂️
Got to do what you got to do. Thanks for watching!
the previous year S240 had the Tuff Torq K46 transaxle, but this year John Deere advertises it as K46 Heavy Duty. Is there a change to this year's K46? Does it have a more sturdy build or a higher torque rating than the previous year? I looked on the John Deere and Tuff Torq websites but they don't say if there's a change in specs.
I don't think there were any real changes from what I have seen and read. Great question and thanks for watching!
@@WesternEquipment ok thanks
Hi Brent was wondering if you might be able to help me with something, purchased a 2020 s240 got about 10 hours on the machine and the gas tank gauge does not work , is there a simple fix that I can do myself I am good with wrenches thanks.
So the gas tank is a floating tank that sits on an arm that runs your float gauge. It could be a couple of different things. Either that arm that goes from the gauge to the underside of the tank is broken or your tank may have springs that help hold it in place and one of them may be broken. I wouldn't sat this is a simple fix just because of how much disassembling will have to be done. But those would be the issue cause the gauge not to work. I hope this helps and thanks for watching!
I've got an S240 on order. Pretty excited, not gonna lie.
Awesome! I hope you enjoy it! Thanks for watching!
Question. I am comparing this model with a s170. But what gives me pause is why does the s240 have smaller rear wheels and an engine with less horsepower than a s170?
Well the S170 is meant to be in the upper class of the 100 series mowers so there for it gets higher horse power and some larger back tires.
Great Review. Got my S240 earlier this week and love it. Been watching your videos ever since I got it. Two questions though.
1.) Is the bagger system the same for 2020 - 2021 S240's? Your parts store only lists one option for it so I just want to make sure?
Thank You.
Yes, except there are some upgrades to the 2021 version. Thanks for watching!
I've been looking at a s100 for my son, he wants to mow yards would u recommend the s100 or bigger?
If he is just starting out mowing smaller yards then i think this would be a perfect starter mower. Thanks for watching!
washout port- why use it only once a year or so? I see other people mentioning using the port after every cut especially if grass not perfectly dry
You could do this as often as you want. I would just suggest making sure it dries out underneath so you are night fighting rust.
Brent do you know overall length with the bagger on the back? Thanks great job with all the videos no one compares to the detail you bring!
When I measured one of these last it was close to 89". I hope this helps and thanks for watching!
Great video. Do you think you could do an S220 vs S240 video? I bought the S220, mainly because the dealer had some on order and I needed it quick. I'd love to know what I gave up.
I am hoping to do a video over the S220 soon. Still waiting on some to arrive. Stay tuned and thanks for watching!
My yellow seat is basically falling apart.. other than that I love it.
Plus it’s very hard to gas up.. any suggestions? Thanks
Seat cover should fix you up on the seat and as far as filling the tank a like fo use an extended funnel to avoid the mess. I hope this helps and thanks for watching!
I understand wheels have bushings, not bearings? If so, are bushings replaceable & is this an expensive repair?
Yes this is true and no it is not an expensive repair. And it is very simple to do. Great question and thanks for watching!
A question: the grease fittings on the spindles , are the bearings sealed or open to except grease ? The older decks on J D ‘s were sealed bearings and the grease never got into the bearings! Same thing on the new ones ?
Yes they are sealed but it is important to make sure you grease your spindles to make sure to keep moisture from building inside and possibly damaging the shaft. Great question and thanks for watching!
I have an L120. Whats the biggest engine i can put on it. My 22 hp briggs is running on 1 cylinder. Or is there something i can pit in it to free up the second cylinder
I would suggest staying with the size that originally came on the machine. Thanks for watching!
Great explanation of how to operate mower.
Thank you and thanks for watching!
Just got my S240 with the 42 inch deck and am looking forward to grass cutting season with my 3 lots of land instead of my self propelled Toro. Side discharge is fine for me through the mowing season, and I don't want to drop the money on the mulch kit and blades and would like a mulch plug option for the leaves in the fall with the Accel Deep Mower Deck. Otherwise I will be tempted to use my 22 inch Toro Recycler with the mulch option for all my yard in the fall.
Unfortunately on the Accel Deep deck the mulch control kit is the only option. You might be able to fabricate something as a cover over the opening to accomplish the leaf mulching. Thanks for watching!
I have the mulch kit on my S240 42". I think it was about $300. Works well and worth the money.
Can I get 2021 S240 42inch
mulch control system and baggers from your digital store? It dispenses lots of clippings outside. Lawn looks messy after mowing. Any suggestions please.
Unfortunately both of these items are unavailable from John Deere right now due to manufacturing delays. We are hoping this resolves soon. Thanks for watching!
@@WesternEquipment please respond the thread when it’s available.Thanks
Excellent video, thanks! I'm waiting for my 42" to be delivered; bagging system seems to be holding it up. Cheers!
Thank you and congrats on your new mower! I hope you like it and thanks for watching!
My wife and I are in our early to mid 60’s and looking at buying a new John Deere s240, or x330, 42” deck, Kawasaki engine (locating one has been difficult due to Covid). We have about 1 1/4 acres mostly flat ground with a few trees. Your videos are helpful and informative in making an initial purchase decision, and service afterwards. Thanks, we appreciate it! Wilbur & Loyce, North Florida
Thank you so much and I am glad I could help. Hopefully you all can find one soon and thanks for watching!
@@WesternEquipment just one quick follow up, do you think the x330 would be worth the additional $600 over the s240 for our use? 1 1/4 acre Mowing, Bagging, pulling a cart, fertilize spreader, and possibly thatcher attachment? Thanks again! Wilbur
@@wilburreeves8329 theyve got the same engine and transmission, and even the same tires. The deck lift and height adjustment along with the x330 having a somewhat heavier frame are the most notable differences. I think the x330 has a longer warranty also. I mow about almost 2 acres currently using a honda hrx217 pushmower and cub cadet ltx1040 42" tractor. I have to mow rather slow to achieve a decent cut with it,so I'm looking to upgrade. I think the s240 would suit my needs ok,because I dont have any steep hills or substantial obstacles and seldom tow anything.
Hi Brent. Thanks for your excellent videos. They've helped me to decide on the S240 with a 42" deck. I'd like to find out if you agree with that choice or if the 48" deck would be better.
I plan to mulch about 1.5 acres of flat as well as somewhat sloped and rough terrain at a height of around 3.5". A shorter cutting time with the larger deck is not an important consideration. I picked the lighter deck so it's easier to adjust the cutting height and remove it for service, less expensive to add a bagger and to maintain 2 vs 3 blades / spindles, easier to fit the tractor on a 5 ft wide trailer and because it should be more maneuverable on slopes.
I'd be grateful if you could answer a few questions.
Does the MulchControl kit work equally well on both decks or are the results better on one of them?
Would a well maintained 42" stamped deck be as rust resistant as a 10 gauge forged 48" deck?
Is there less risk of damaging a blade / spindle on sloped rough terrain with the additional 2 gauge wheels of the 48" deck or more risk due to the greater width?
Which deck would you recommend for this lawn?
Thanks very much for your help.
All great question. To start, yes, I would go with the 42" deck. The mulch control works well on both models and there is no advantage in rust protection with the thicker steal. there is going to be less risk of damage with the shorter deck and I would definitely recommend the 42" deck for your specific situation. I hope this helps and thanks for watching!
@@WesternEquipment Thanks very much for your time Brent to answer my questions. I really appreciate the help to confirm that an S240 with a 42" deck is a good choice for this lawn. Take care and have a great day!
I wanna do some yard mowing for my neighborhood, they are 1 acre or just a bit more, what would be the model in the s100 or 200 series? Or a good used model? Thanks
Any of the 100 or 200 series models would be great, even in the used models. Main thing you need to decide is what size of deck you need to get in and out of gates if you have that issue. Good question and thanks for watching!
seat slide works better when there's no weight on it! Found that out myself the same way, LOL.
HAHA right! Seat slides don't like the big boys sometimes but i bet some WD-40 would fix that right up. Thanks for watching!
What type of gasoline do the s100 mower use
Great video. I’m looking to purchase this mower in the spring. When does John Deere release the info for the 2022’s?
Thank you and the info is already available to dealers so I would assume it is coming soon to the public. Thanks for watching!
Great review, as always! I picked my 2021 S240 up about a month ago, so far so good. I was concerned about the fuel filter physically touching the engine, so I used a zip tie to pull it closer to the battery by wrapping it around the fuel line and the battery strap. It has done a good job keeping the filter off the engine. Also, any clue when part # BUC11053 will be available? I'd love to get mulching, but I haven't seen the mulch control kit attachment in stock. Thanks again!
That sounds like a good idea! And I wish I could give you an estimated stock date on that kit but I do not know and we have been trying to get info for a while now. There have been tons of inventory issues with most major vendors so we are all hoping this gets resolved quickly. Thank you for watching!
Looking at a used one but it does not have the side by side pedals on the right like this one. Were earlier versions different?
Yes, some earlier model lawn tractors did not have the twin hydrostatic pedals. Let me know if I can help with anything else on this machine is you purchase it and thanks for watching!
Curious on the oil change with the new fr651v that has the 2.2 quart oil capacity. Will the purchase of 2 quarts be enough due to residual oil that may stay in the engine, or should a partial small amount from a third quart be required? Oil change kits are still showing just 2 quarts. Also, this is my first kawasaki engine. Is it normal for them to require topping off the oil alot? Are they oil burners?
Usually 2 quarts does the job and I have not experienced them being oil burners and have not heard that from our service departments either. Good questions and thanks for watching!
@@WesternEquipment Thanks for replying.
Thank you sir. Your very informative videos have helped me to sift through a lot of info very quickly. I have ordered my S240 in 42" deck with a Mulch kit. Very excited and can't wait to get it in
Awesome! Thanks for watching and i hope you enjoy your new mower!
Are you sure the lights are halogen and not incandescent bulbs?
They are incandescent, I misspoke here. Good catch and thanks for watching!
Great video. Very informative. Can you make a video on how to install the mulching kit? Thanks.
Thank you and yes this is on the list. Thanks for watching!
Your videos are great, we just ordered a 240 with a 42 inch accell deep deck, is the 42 a good cutting deck, does it mulch well, bag well?
I don't have the mulch kit on mine and I'm noticing that the engine is so powerful that you don't really notice the clippings on the lawn. I wouldn't be concerned unless you are doing it commercially or you are having a party/event and you don't want clippings brought in, which are also greatly reduced due to the Kawasaki engine when compared to my push mowers and previous rider.
Thank you! Yes, it is good for mulching and bagging. Being that it is a smaller deck and processing less material than a larger deck makes it good for both of these applications. Thanks for watching!
Just wondering if you can guess why JD stopped offering the freedom 42 deck? I own a 20 year old LT 160 with the freedom mulching deck, the deck mulches perfectly only had to replace the timing belt once in all the time I owned it. I have a new s240 with the 42 deep cut deck on order from the local JD green store, they said might be in by mid June but they can't say when the mulch kit will be in. I'm still cutting with the LT but the Kohler is burning oil under load almost to the point of "hope the neighbors don't call the EPA on me while I'm cutting" mode.
I honestly do not know why they discontinued the freedom deck. I have heard numerous times how well they work. The mulching kits have been an issue to get for a while now so I am hoping this gets resolved soon. Thanks for watching!
@@WesternEquipment The price of progress I guess, thanks for your reply.
I just got this mower & it’s awesome. To one of your points, when it’s time to replace the fuel filter, I’ll remove the battery to gain much needed space. Have a question regarding the primary deck belt. On you video, with blades engaged, the section of belt going to the far left spindle runs smooth. On mine, kind of flops around a lot. My dealer said it is normal. Any remedies? Thanks.
Glad you are enjoying it! you may need to see if there is some adjustment you can make to one of your idler pulleys to take out the slack. You don't want it too tight but there shouldn't be any flop when running your blades either. I hope this helps and thanks for watching!
Are there any other spots I should be greasing? And how often should I be greasing them?
Thanks in advance!
The points shown will be the only true lubrication points and the spindles should be done every 8 hours and the front axle should be done every 25 hours. Good questions and thanks for watching!
My pop pop bought a 2018 one of these with a 17 horse Kowasaki to replace the LA110 he gave to me it's an AMAZING TRACTOR 😁😁
Nice! Thanks for watching!
Do you have a review of this lawn tractor with the 42" deck?
Unfortunately I do not at this time. Hopefully in the near future. Thanks for watching!
Thank you really appreciate the detailed information provided, very informative and helpful
Thank you and thanks for watching!
What I have always liked about my Craftsman is the ability to mow in reverse without making any additional actions. One lever for choke and throttle combined. Start the mower , reposition the start key to a reverse position and mow in in forward reverse anytime. My reverse is with a handle similar to the deck lever and my hand is always on it. Quick and simple. I don’t need two foot pedals nor an extra button for reverse. J-D has too many buttons and levers. That’s not a high end sports car you have there, it’s just a grass cutter.
Well thank you for the feedback and I appreciate hearing other peoples opinions. Thanks for watching!
You've got the same cvt transmission my old cub cadet has. It's good as long as you dont have alot of obstacles when you're mowing,but if you have to change direction alot a hydrostatic tranny allows alot quicker transition. I will agree that I'm not a fan of john Deere's mow in reverse feature,but the s 240s loaded with high quality features and the deck is second to none. The best selling feature is john Deere's impressive customer service after the sale. Craftsman service is no longer available and you'll not find any stocked parts. Independent shops will work on them,but you wont be a priority and you'll be waiting on parts being ordered. I'll stick with john deere or cub cadet when I get a new mower.
The reverse switch is very easy to by-pass, took all of 5 minutes. I had a mower with the handle for forward and reverse and liked it until I got this one, now I much prefer the foot pedals.
@@redbone5363 yeah,I bypassed mine on my cub cadet too.
buying our first new riding mower in 20 years. My dad and I were surprised. Mowers today are more complicated for no reason, not to mention more expensive. Back then the one we got was 900 bucks and all metal. The S130 we were looking at is $2800 and is half plastic. So many buttons and features that are gonna break in time. That digital gas reader, parking brake button, cruise control?? lol And we asked that too, why is it so complicated to mow in reverse? On the old mower all those buttons and extra pedal were basically in one lever, and mowing in reverse wasn't something you put extra thought into, it's a basic thing.
Not sure why it's like this either like you said it's just to cut the grass. But i'm guessing like anything else, it's so they can charge you more and they put all this extra flimsy crap cause they don't want you to have it for years and years. They want it to break so you to run out and buy another.
I got this same 2021 S240 model with a 42” Accel deep. What begging kit is recommended? I have been told I need a special one that isn’t manufactured yet by a JD dealer but I believe they are blowing smoke because everything is back ordered. Thank you!
The one you need is a BUC10907 and from what I see it is still not available. John Deere has been having inventory issues, but we are hoping to see them resolve soon. Sorry for the inconvenience, but thanks for watching!
No baggers avail in MN 😞
Hi. Thanks for the informative video. Has JD stop S240 42 inch deck riding mower? I tried to buy now but no availability in our state. Thanks
They have not stopped producing them but there is currently a shortage of parts and materials so building some machines have been difficult for John Deere. Hoping this issue gets resolved soon. Thanks for watching!
Can I buy this product in south Korea? john deere products are not officially imported.
That is a good question. I would have to look into that. Thanks for watching!
Looking at purchasing new lawn tractor! Been looking @ S240 with 48 deck & X350 with 48 deck. I think I noticed there are differences in these 2 decks! Looks to me 48 inch deck on the X350 has easier adjust scalp wheels as well as swivel scalp wheels for easier deck removal? Also is the deck thickness the same on both 48 deck on S240 & the 48 inch deck on the X350?
Yes, you got it! The anti scalping wheels are better for deck removal on the X350 but the gauge of steel on either model is the same. Good questions and thanks for watching!
@@WesternEquipment so could you get John Deere to put the x350 48” deck on the s240 that way you could have the upgraded deck but on a s240?
Do you know why California does not allow the 48” deck?
I don’t. I actually haven’t heard of this. I will see what I can find. Thanks for watching!
So, in total, there are 6 grease points, 3 spindles, and 3 front for the front axle?
Correct! Thanks for watching!
Hi Brent just passing through and saw this video. Great video very informative.We are the manufacturers of the Kavli Blades and make mower blades for the John Deere. I think you would be very surprised at what these mowers are capable of with our blades.
Thank you and yes i think that would be interesting to see! I will have to look more into this. Thanks for watching!
If you need test blade users, or are selling, I’m willing to try them on my x384
Doing a video on the lawn sweeper soon?Would help me decide whether or not to pick one up.
I will try to get a demo out on it as soon as we have enough grass to mow! Thanks for watching!
What's the Retail price for the 48 " Deck . What type transmission?
The retail price as of early 2021 was around $2899 and the transmission is a Tuff Torq K46. Prices may vary depending on location and with 2022 models coming soon. I hope this helped and thanks for watching!
Hey Brent can you get those fender flares for the S100? I really like the look and extra protection to the body.
They do not show to be compatible for the S100.
@@WesternEquipment Thanks it looks like they are just for the X700 series correct?
Great video! I too am waiting for mine to come into my local dealer!
Hopefully they will start rolling in soon. Thank you and thanks for watching!
INTERESTING QUESTION FOR "WESTERN EQUIPMENT" ABOUT THE NEW S240; YOU MAY NOT BE ABLE TO ANSWER THIS BUT,... WHY DID JOHN DEERE DUE AWAY WITH ALL THE HEAT VENTS ON BOTH SIDES OF THE ENGINE HOOD EXCEPT FOR ONE SMALL SLOT IN THE TOP CENTER,..? EXCEPT FOR THE FRONT GRILL AREA IT SEEMS LIKE SINCE HEAT RISES,..THERE WOULD BE EVEN MORE HEAT BUILD-UP WITH LESS HEAT VENTING OR DISPERSION ABOVE AND IN THE ENGINE AREA.
I wish I knew the answer to this. John Deere seems to like to change up their styling designs often so I'm assuming this on one of those type of things.
@@WesternEquipment THIS NEW HOOD DESIGN IS IN ITS 2nd YEAR I BELIEVE,... HOPEFULLY THEY KNOW WHAT THEIR DOING,..? I'LL KNOW BETTER MYSELF ABOUT THE HEAT ISSUE WHEN MINE ARRIVES IN A COUPLE OF WEEKS.
if you want to use a mulching kit do you need to change blades on a 240 48" deck ?
It's a good idea to change to the mulching blades because they have a longer cutting surface that will help to mulch the grass finer. Good question and thanks for watching!
@@WesternEquipment what would the part number be for the blades?
LOL...you sold me on this one :) great detailed review
Thank you and thanks for watching!
Can you speak to the mulcher kit delay/recall for the new 2021 S240 42inch deck - thank you!
There are parts availability issues worldwide. From what I have heard there is just a shortage of raw materials and also a lack of transportation to get parts and materials to manufacturers. I'm hoping it gets resolved soon. Thanks for watching!
My local dealer says production has been shotty for the S220 at the factory. That's why there's none around.
hi brent i just bought a new s130 and it was missing a spindle cover would that be under warranty ive already contacted and made case with john deere so im tryin to get that cover its rh spindle cover,and ive heard lot people had that happen to,ok later brent
Sounds like you have gone through the proper channels to get your issue resolved and yes this has been happening a lot and I'm not sure why. Let me know what happens and thanks for watching!
@@WesternEquipment hi brent I got update from john deere case and they sent me a diagram and parts list for the s130 42 deck and said there was no part only a cover over the lh spindle is shown on the diagram and parts list so I guess there was no cover after all but I'm thinking maybe the lh cover will fit the side ok have a good one brent.
hi Brent they corrected my case and now there is a spindle cover for the s130 john deere tractor mower, part number GY21773,it is if your veiwers need one to,for the 42"edge deck,they said will send me one out asap,so hope resolved soon sorry to bother you with my problems but it was just a missing part that i didnt get,ok good videos Brent ill be watching,later brent
How often should I be greasing all these points, maybe a rough estimate?
The deck spindles should be done every 8 hours and the front axle should be don every 25 hours. Good question and thanks for watching!
Thanks man! The video is great, been looking for a new lawn tractor did a ton of research and decided on the 240, with the 48", the case iron front axel, 10 gauge steel mower and the engine really sold me. Love the capabilities and upgrades from the 100 vs the 240 model.
This video really took me over edge to purchase.
Well I am glad I could help you with your decision and thanks for watching!
Just received my mower from a local dealer with the mulch control kit installed. very nice. QQ on the Bluetooth module (BUC10929), my dealer has attempted to order this part several times, Deere cancels the order even though they show 150 in stock. The dealer speculates Deere is holding onto these for the new units which I find curious because I purchased mine new. Have you had a similar experience?
Yes, we have had issues getting this part and are still waiting on a response as to when it will be fully released. I wish I had more help on this topic. I am wanting to get one to so that I can do a video on it. Hopefully it will be resolved soon. Thanks for watching!
@@WesternEquipment curious if you've had any luck since we first broached the topic a few weeks ago
Does anyone know if the tall wheels from the E/S170-180 will fit on this? They look so much better.
This is a good question. I would have to do some research. Thanks for watching!
anybody buying one of these check up on the center of the front axle, if they still put a grease zirk there make sure it gets greased frequently. If the bushings don't wear the axle does causing the front tires to tow out horribly causing it to steer very hard. Keep it greased and no problem. I've replaced front axles on several of these 100 series JD mowers. Other then that these are good econo/quality mowers. Former Tech.
This is very true! I should have mentioned this in the video.
The real question is what mower do you use😳
Haha, well I have a very small yard in town so I actually used to use a John Deere SB14 until it finally gave up on me. I now use a Honda self propelled HRN216VYA. Once I move and have more area to mow I will get a John Deere zero turn and maybe I'll even show it off in a video! Thanks for watching!
Thanks for your great videos and the way you answer questions! I just used my new 2021 S240 with bagging option and it worked great. I have a question regarding addition of a mulch control unit. Is part BUC10704 the correct part? Also, I read that you can use the mulch control and bagging system simultaneously resulting in partial bagging and partial mulching; is this correct? If so, what blades (bagging or mulching) would be best for this operation? Thanks again!
Yes, that is the correct number for the mulch control kit for a 42" deck. I'm not sure about using them at the same time as I have not seen that combo, but if so then I would use a standard 3-in-1 blade. I hope this helps and thanks for watching!
@@WesternEquipment thanks! But now I'm confused; I just saw that a Deere representative said on the Home Depot site that the correct mulch kit part number is
BUC11053
@@WesternEquipment is the mulch kit (BUC11053) available yet? If not, any idea when? Thank you!
Hoping to get myself into one of these in the next year or so..
They are pretty sweet!
Hey Brent could you do a deck-leveling video on the Z700 series Zero turn? Thanks.
I will get it on the list! Thanks for watching!
Just bought a new S240 and a few days after the 1st mow, I found 5 random areas of dead grass in the lawn and after the second mow on Saturday, there are 4 more patches. They look like fuel burns and I’m guessing it’s coming from the mower. Anyone experience this before? I will be calling the JD dealer tomorrow. Thanks
This is interesting, I will be following this thread. Thanks for watching!
@@WesternEquipment thanks - dealer insisted it’s not the mower so I push mowed this weekend and waiting to see if any new spots appear. If not, I will mow with the JD on Wednesday and then see if any new spots appear. Dealer thinks it’s either stray dogs or rabbits doing the damage so we’ll see.
I had the same thing happen I found it’s where you stop and sit at full throttle it burned the grass. If I stop now I lower the throttle haven’t seen any since
Do u have a video of 2022 s240 48 or is it same as 2021
They are very similar.
Great video! What would be the advantage of going from a S240-42" to a X350-42"? They seem to have the same FR651V engine and K46 transmission.
Did you make a decision on one? May I ask why? I'm in the market for a new mower. Thanks.
@@cambellschunky704 not yet. I have been researching a while. I sat on a X370 the other day. I must say the seat was really comfortable compared to the one on the S240 and X350.
@@steve9377 The X series is a class above the base S class so I'm not surprised about the comfort. X3 vs X5 may is a model difference as well as the next number. The last number is an engine designation.
I am leaning towards a Kawasaki motor.
Is there a reason you have not considered a zero turn? I would like one, but my elderly mother may have trouble with those controls.
@@cambellschunky704 I’ve driven a zero turn a few times, I hated it. I’ll choose a steering wheel and pedals every time. Weird thing about the seat is once you get into the X500 series it goes back to the not as comfortable seat. A Kawasaki engine is a requirement for me. I wish John Deere would openly say it has a Briggs or Kawasaki engine instead of trying to mask it under the Cyclonic or iTorque names.
The biggest advantage is the additional frame size and strength. Then there are various smaller advantage such as an upgraded display panel and more attachment options. I hope this helps and thanks for watching!
Awesome. Thanks. New one just arrived.
I hope you enjoy it!
Still debating between S240 vs X350 (42") as both have same engine, so what is that price difference?
It looks like there is about an $800 difference. Could be more, could be less depending on where you shop. I hope this helps and thanks for watching!
@@WesternEquipment sorry I meant why is the price difference and not what. I have around 16000 sq ft to mow with some slope.
@@SwapnilBhartiya as of right now the order in features of John Deere mowers go from the series (the ones shown in Lowe’s etc, and goes from s100 to s180) then goes the s series but the s240 which is right in the middle in between the s and x series. The x series have a lot more features to choose from but cost more.
@@manofculture4945 Ditto. S240 has same engine and other features in x350 except may be the steel is a few mm thicker in x350 pls one extra year of warantee. So I am not sure if $1000 is worth given I am just a home users with 17000 sq to cut. In most cases there is huge difference in quality and sustainability but at this point i am a bit confused.
@@SwapnilBhartiya yes I would go for the s240 there are barely any differences apart from the hood design
How is it compared to the Xseries
This is sort of like and X series in a 100 series body if that makes sense.
I’m 14 I want to start a small landscaping Business and have no money but I want to start in the winter what is the cheapes John deer do you have
The cheapest model will be the S100 and it would be a great starter mower. Good luck buddy and thanks for watching!
@@WesternEquipment do you have a price on that
@@Clemson-rc2yq go to the Lowe’s or Home Depot website or go to a John Deere dealer
@@manofculture4945 I’m looking to buy a used tractor for my fist season them buying a new one because plowing can be rough to get customers the first year so I just need to see how many people I can get before I have to shell at 1500$ on a lawn tractor
@UCKDDKNCB2eZNpm1wITwbnqw I work on small engine so I know my stuff I would like to find one with the plow or snowblower but that is very hard