Nicely done. A great mod getting away from those terrible old-style terminals. I was shouting at you about the colour layout during the build but you didn't hear me. In my 50 years working with audio and video I've always known the negative terminals to be "inboard" of the positive terminals (unless the terminals are stacked vertically). I've subscribed. Edit:- Just noticed on your rewiring video the Parasound component looks the other way around!
This is a really cool idea. I hate those old push pin connectors. It would be interesting to do something similar with the hardwired power cord as well. Though I suspect it would require modding the power supply and isn't worth the effort.
Like minds think alike, been on my mind for years, just never got the chance to do it. I would have marked everything before cutting and drilling the aluminum. Makes it easier to clamp without damage to the sides of the piece you are using. Just my two cents. Old carpenter and hifi nut.
I like this and will probably do it on an older stereo system I found at an estate sale. One question, from older connections/connectors to the new one, did you notice any improvements with the sound quality?
Depends which brand cables and terminals you use and to some extent, how much you spend.. However, to reach that point you must be a proven elite and gifted audiophile
While this is a good idea, there are some points that compromise the new connectors. Firstly, they are screwed together. A one piece leading copper lead with a surface treating and no nuts to tighten, will perform better. Both mechanically and sonically. In this case, I would probably have undone the soldering flange and the nut and tossed them away. Then I would have drilled a hole through the rod and soldered into that. I just changed the terminal on my 30 year old Copland amp, and that, I can guarantee you, was a sonic improvement. What it does is a better connection, also to the gauge of the wire. If you can imagine the this wire from before, only touching a many decade old clip, which is also dirty, the connection is just bad. The current have very little and dirty surface area to move through. Next point, which is also valid on almost all modern cables and connectors of today, is the idea of pinching strands of wire with screws, thinking it makes a good connection. Well, it does not. If you have say 200 thin strands in the wire, the contact point between them are minimal. Therefore you need to solder your cables in both ends. Also using proper flux to clean the contact area(-s) and secure proper clean soldering, as well as actually using the MUCH bigger area for the current. Very few, including companies do this. But that is the proper way. Kind regards.
Nice getting rid of those nasty vintage post connectors! Just one comment - did you vacuum out the filings from the case? It's the only thing that struck me as undesirable in this upgrade. All the best, Rob in Switzerland.
While this is a good idea, there are some points that compromise the new connectors. Firstly, they are screwed together. A one piece leading copper lead with a surface treating and no nuts to tighten, will perform better. Both mechanically and sonically. Next is the brass that yours are probably made of, which have a terrible conducting property. Get copper mixed with tellurium which hardens the copper, and only loose 2-3% conductivity relativer to pure copper. Silver on the outside enhanced this again. In this case, I would probably have undone the soldering flange and the nut and tossed them away. Then I would have drilled a hole through the rod and soldered into that. I just changed the terminal on my 30 year old Copland amp, and that, I can guarantee you, was a sonic improvement. Less mud in the sound - a cleaner sound with a little more detail.. Not much, but there. What it does is a better connection, also to the gauge of the wire. If you can imagine the this wire from before, only touching a many decade old clip, which is also dirty, the connection is just bad. The current have very little and dirty surface area to move through. Next point, which is also valid on almost all modern cables and connectors of today, is the idea of pinching strands of wire with screws, thinking it makes a good connection. Well, it does not. it's just as bad as bare strands clipped into the old style flipping plate connector. You may be remembering black strands, black connector etc, from the old days. Well, that's what is happening. Same with the modern connection, if NOT done properly. If you have say 200 thin strands in the wire, the contact point between them are minimal. Therefore you need to solder your cables in both ends. Also using proper flux to clean the contact area(-s) and secure proper clean soldering, as well as actually using the MUCH bigger area for the current. Further, any area exposed to air, should be covered in say an acid free silicone sealant, to prevent future corrosion. Many modern connectors, also expensive ones, are not well executed, with lots of small parts assembly, open for bad future connection, corrosion, loosing up and what not. Also, take a look at the quality of a current leading alloy or metal. Brass is often used, and is bad. Copper is better, Silver is the best. Silver plated copper with a bit of beryllium is very good. All these big clear plastic parts are good for turning knobs as in not carrying current, but bad for not being able to be surface treat the current leading metal beneath, which will then corrode. So, take a good look at stuff and do it properly. Very few, including companies do this. But that is the proper way. Kind regards.
No changing the bind posts will not improve the sound quality it just makes connecting wires and cables much easier especially if you have multiple cables or speakers you want to test out
Good job. Looks clean and up to date.
Cool upgrade. Looks good!
Nice job. I remember those old connectors-still hate them.
Nicely done. A great mod getting away from those terrible old-style terminals. I was shouting at you about the colour layout during the build but you didn't hear me. In my 50 years working with audio and video I've always known the negative terminals to be "inboard" of the positive terminals (unless the terminals are stacked vertically).
I've subscribed.
Edit:- Just noticed on your rewiring video the Parasound component looks the other way around!
This is a really cool idea. I hate those old push pin connectors. It would be interesting to do something similar with the hardwired power cord as well. Though I suspect it would require modding the power supply and isn't worth the effort.
in most case it would be simple because the ground wire in a power cable is just connected to the chassis ground
Thank you for this.
no problem Thanks for watching!
Like minds think alike, been on my mind for years, just never got the chance to do it.
I would have marked everything before cutting and drilling the aluminum. Makes it easier to clamp without damage to the sides of the piece you are using. Just my two cents.
Old carpenter and hifi nut.
Awesome vid. Thanks!
You have kitty!! I love kitty #likedvideo
I like this and will probably do it on an older stereo system I found at an estate sale. One question, from older connections/connectors to the new one, did you notice any improvements with the sound quality?
No you wont notice any difference in sound quality just the ability to use any type of speaker wire or cable and easily swap out for others
@@The.Home.Cinema.Engineer OK, thank you.
Depends which brand cables and terminals you use and to some extent, how much you spend..
However, to reach that point you must be a proven elite and gifted audiophile
While this is a good idea, there are some points that compromise the new connectors. Firstly, they are screwed together. A one piece leading copper lead with a surface treating and no nuts to tighten, will perform better. Both mechanically and sonically. In this case, I would probably have undone the soldering flange and the nut and tossed them away. Then I would have drilled a hole through the rod and soldered into that. I just changed the terminal on my 30 year old Copland amp, and that, I can guarantee you, was a sonic improvement. What it does is a better connection, also to the gauge of the wire. If you can imagine the this wire from before, only touching a many decade old clip, which is also dirty, the connection is just bad. The current have very little and dirty surface area to move through.
Next point, which is also valid on almost all modern cables and connectors of today, is the idea of pinching strands of wire with screws, thinking it makes a good connection. Well, it does not. If you have say 200 thin strands in the wire, the contact point between them are minimal. Therefore you need to solder your cables in both ends. Also using proper flux to clean the contact area(-s) and secure proper clean soldering, as well as actually using the MUCH bigger area for the current.
Very few, including companies do this. But that is the proper way.
Kind regards.
Nice getting rid of those nasty vintage post connectors! Just one comment - did you vacuum out the filings from the case? It's the only thing that struck me as undesirable in this upgrade. All the best, Rob in Switzerland.
yes I was sure to vacuum the filings. thanks for watching!
You can buy banana plugs with about an inch of Braided speaker wire sticking out of them that you put into the old spring clips
yes an ok fix to a permanent problem with those old style speaker clips
While this is a good idea, there are some points that compromise the new connectors. Firstly, they are screwed together. A one piece leading copper lead with a surface treating and no nuts to tighten, will perform better. Both mechanically and sonically.
Next is the brass that yours are probably made of, which have a terrible conducting property. Get copper mixed with tellurium which hardens the copper, and only loose 2-3% conductivity relativer to pure copper. Silver on the outside enhanced this again.
In this case, I would probably have undone the soldering flange and the nut and tossed them away. Then I would have drilled a hole through the rod and soldered into that. I just changed the terminal on my 30 year old Copland amp, and that, I can guarantee you, was a sonic improvement. Less mud in the sound - a cleaner sound with a little more detail.. Not much, but there. What it does is a better connection, also to the gauge of the wire. If you can imagine the this wire from before, only touching a many decade old clip, which is also dirty, the connection is just bad. The current have very little and dirty surface area to move through.
Next point, which is also valid on almost all modern cables and connectors of today, is the idea of pinching strands of wire with screws, thinking it makes a good connection. Well, it does not. it's just as bad as bare strands clipped into the old style flipping plate connector. You may be remembering black strands, black connector etc, from the old days. Well, that's what is happening. Same with the modern connection, if NOT done properly.
If you have say 200 thin strands in the wire, the contact point between them are minimal. Therefore you need to solder your cables in both ends. Also using proper flux to clean the contact area(-s) and secure proper clean soldering, as well as actually using the MUCH bigger area for the current.
Further, any area exposed to air, should be covered in say an acid free silicone sealant, to prevent future corrosion.
Many modern connectors, also expensive ones, are not well executed, with lots of small parts assembly, open for bad future connection, corrosion, loosing up and what not. Also, take a look at the quality of a current leading alloy or metal. Brass is often used, and is bad. Copper is better, Silver is the best. Silver plated copper with a bit of beryllium is very good. All these big clear plastic parts are good for turning knobs as in not carrying current, but bad for not being able to be surface treat the current leading metal beneath, which will then corrode.
So, take a good look at stuff and do it properly.
Very few, including companies do this. But that is the proper way.
Kind regards.
May I ask which speakers you are using? :)
@@vloc88 they are the KEF iQ90
Wire Farrels
You must hear a better quality of sound or detail or space do you not?
No changing the bind posts will not improve the sound quality it just makes connecting wires and cables much easier especially if you have multiple cables or speakers you want to test out