I just founded recently your channel, while am involving in a huge project in power telecom industry within one of the scope is to upgrading the firmware of Deep sea to a version up 7.5. Thanks, this video'll help. From DR Congo/Africa
Technical question: I have here a generator with apm303 controller. If the gen is started with the breaker off the engine runs as it should. If the gen is started with the breaker on the engine starts but shuts down because it sees no voltage and Hertz. Could the problem be in the cable after the breaker?
Hello sir. you give me an very important information about the firmware I have a request : in troubleshoot, in this case we need to update the DEEPSEA firmware Version ? Please can I have an explanation?
One of your subscribers, I work in a generator company in Bangladesh as a service engineer, the company name is Cross World, there will be a generator business in the future, at the rate electricity is developing, I don't think there will be a generator business. What is your opinion on this matter? In one word, there will be a generator business, or not
Generator is good business if you think itle be gone it take longer coz engine can be modified to become clean and renewable so for me its still a good business for a long run
i have a question sir,,,,i have a deep sea controller 6120 ,,,,keeps bringing this"memory corruption refer to manual" error while i fixed it by updating firmware,Could it be receiving some other signals??
HI FRIEND HOW ARE YOU CAN YOU PLEASE EXPLAIN ME I HAVE A MODULE MKII 8610 IT HASE HA BOOTLOADER ERROR CAN YOU PLESE TELL ME HOW CAN I SOLVE THIS PROBLEM THANKS
salam sir i am generator operator i have problem with my dse module a message is occurring when i connect the pc to the dse 4520 module the error is (scada information is not available for this module a software upgrade is required) tell me the solution plz
Dear sir, I have a problem. DSE 7310 panel showing "Memory corruption, Refer to manual, AC comms fault". Can the fault disappear if i update the firmware? Please advise me.
@@benzblogsVlogs Hello sir, after update firmware, found a problem. I can not insert configuration. Module request a module pin no(4 digit).. How could i get module pin no(4 digit)?please answer to me sir.
@@benzblogsVlogsi can't write configuration.Module request pin code.I think supplier control the pin code.I have been insert possible 4 digit code.That is not working.How do you think sir for that problem?
Engineer pls i have auto start controller model : 7320 version 7.0.7 (not DSE °) problem with analogique input ( not present 7.0.7 ) help me please update firmware
@@mohamedbayoudh1395 no if you have update sofeware dse configurat if you did config it will update automatically your module to the latest that the new now in dse
![โอ้เธอช่าง... - บี้เดอะสกา ft. ต๋อง เทวัญ (Prod. by ป๋าเพชร) [Official MV]](http://i.ytimg.com/vi/zbWhiLFmVL0/mqdefault.jpg)
Greetings from Bulgaria!
I am a generator service technician.
I have learned more from you than from my manager.
Be healthy!💯
Thank you so much bless u
@@benzblogsVlogs Good morning sir
How i can change old and obsolete module, for exemple DSE 5320 to new one dse 7320
I just founded recently your channel, while am involving in a huge project in power telecom industry within one of the scope is to upgrading the firmware of Deep sea to a version up 7.5. Thanks, this video'll help. From DR Congo/Africa
Welcome thank for the trust pls like share thank you
Sir after updating, we found out an alarm Input E appeared.
How can we clear that ?
Nice one idol salamat sa mga video mo.godblees idol
Ganon din sayo lodi
Watching here lods, Salamat sa pagbahagi, bagong kaibigan kabayan, sana madalaw mo din ang bhay ko.Salamat 🌻.
No prob
Give me link
Nice partner
Thank lods
Technical question: I have here a generator with apm303 controller. If the gen is started with the breaker off the engine runs as it should. If the gen is started with the breaker on the engine starts but shuts down because it sees no voltage and Hertz. Could the problem be in the cable after the breaker?
Check multimeter if really no volatge output make sure voltage sensing is prpoperly provide voltage in the module or ither fuse only busted
I Benz, this for the videos, I am having an issue with my 8610 mkII.. ( Memory corruption).. Do you have an idea on what to do?
Just update firmware
Thank you Benz.. the update solved the issue..
Hello sir.
you give me an very important information about the firmware
I have a request : in troubleshoot, in this case we need to update the DEEPSEA firmware Version ?
Please can I have an explanation?
If you update ahoudl same module same module example mk1 or mk2 version is varry depend on your update u want
Very grateful ! ) Very necessary information for me! Like ! 😊👍💪
Bless u sir
Good morning sir
How i can change old and obsolete module, for exemple DSE 5320 to new one dse 7320
Im
Not try yet but if u can do update the firmware to become 7320
But im
Not yet try this
One of your subscribers, I work in a generator company in Bangladesh as a service engineer, the company name is Cross World, there will be a generator business in the future, at the rate electricity is developing, I don't think there will be a generator business. What is your opinion on this matter? In one word, there will be a generator business, or not
Generator is good business if you think itle be gone it take longer coz engine can be modified to become clean and renewable so for me its still a good business for a long run
@@benzblogsVlogs thanks for good opinion
i have a question sir,,,,i have a deep sea controller 6120 ,,,,keeps bringing this"memory corruption refer to manual" error while i fixed it by updating firmware,Could it be receiving some other signals??
Just update firmware after that it fix your problem
Thanks you bro
Welcome sir
HI FRIEND HOW ARE YOU CAN YOU PLEASE EXPLAIN ME I HAVE A MODULE MKII 8610 IT HASE HA BOOTLOADER ERROR CAN YOU PLESE TELL ME HOW CAN I SOLVE THIS PROBLEM
THANKS
Meaning during the configuration ither unfortunately off the supply or remove the usb that why its happen
But still have a solution on this just update firmware that it
salam sir
i am generator operator i have problem with my dse module a message is occurring when i connect the pc to the dse 4520 module the error is (scada information is not available for this module a software upgrade is required) tell me the solution plz
Just update the firmware to the lataste but before doing that make sure you save the file
Dear sir,
I have a problem. DSE 7310 panel showing "Memory corruption, Refer to manual, AC comms fault". Can the fault disappear if i update the firmware? Please advise me.
Just update firmware problem solve
@@benzblogsVlogs Thanks for your reply & advise sir.
@@benzblogsVlogs Hello sir, after update firmware, found a problem. I can not insert configuration. Module request a module pin no(4 digit).. How could i get module pin no(4 digit)?please answer to me sir.
@@YeMinMyat-r9j try 0000 or 1234 should no password unless if previous config did the password change
@@benzblogsVlogsi can't write configuration.Module request pin code.I think supplier control the pin code.I have been insert possible 4 digit code.That is not working.How do you think sir for that problem?
my update stopped at 71 and shows the device is inoperable?
Just try again do not move or distruct in this process it happen modul will be damage and its become unreparable
Engineer pls
i have auto start controller model : 7320 version 7.0.7 (not DSE °)
problem with analogique input ( not present 7.0.7 )
help me please update firmware
Analog input meaning this connection for your sensor
no found in software 7.0.7 7320 @@benzblogsVlogs
@@mohamedbayoudh1395 no if you have update sofeware dse configurat if you did config it will update automatically your module to the latest that the new now in dse
thank you very much@@benzblogsVlogs
so firmware is copie (chinoi) not original dse
no update