I’m mostly into older jdm cars but recently purchased a 97xlt extended cab 6 cylinder only though . Came with a snugtop to match. Been following along with your rig build and your truck is dope man. The 9inch lift you added so nice man. Keep up the cool videos🤙🏽
I love your videos. They are super helpful. I have a 06 f150 2wd and after watching this I may actually go for the spindle lift over a 2.5 level. Was it easy to fit 35s with the spindle lift? Did you have any rubbing or have to do any trimming?
If You Add a 3 inch Spacer On The Coil Springs Would It Make Your Truck Higher Than It Is Or Would It Just Reinforce The Suspension Since You Already Lifted The Truck With The Spindles ?
You mentioned the spindle lift opens the gap of the upper and lower arms .... that’s not how it works it only relocates the the spindle . Otherwise it would mess with the ifs Alignment... some vehicles can have more lift or less from a spindle lift all depends on the factory locations of the spindle on the factory spindle ... like vids keep them coming
So the kit came with rear struts as well. Did you put blocks in the rear? Or does it kind of level it without the blocks? Are the rear struts okay to put in without putting in the rear blocks?
I’m putting the same lift on my 2002 Ford F-150 2WD and I’m having trouble removing the stock spindles. I’m beating the hell out of it to try getting it out. Any recommendations? 8:45
Very cool and can’t wait to do this too my truck. So are these just stock springs on your truck? My current setup is cut springs and lowered, very sick of this rough ride and setup. I see the 3” lift kit on the rough country website but they only offer the 2” leveling kit springs? Should I purchase these over stock or?
That ford is lookin good Excited to see the upcoming wheel setup You should get new headlights and grille soon that would make it menacingly clean 🤘🏻🤘🏻
@@maxz4065 I did the lift and everything else while I was down there. took about 5 hours with a knowledgeable friend and lots of tools. I fell in love with the truck all over again. new tires and took her in for an alignment. like riding brand new
@@ernievilla6840 not bad at all or at least not very noticeable I also check the tires once a month or so to keep them at proper pressure. She is still on the road and drives great.
Ford sounds good. I have the exact setup on my truck that is similar to it. But Baby Squat sounds better. Man that is a good looking truck and she fits her looks
How did you find what to torque everything to? Or could you just tell me what torque you used? I've looked online and get a bunch of different answers and would just like to know what you used for all the bolts
After the 3” spindle lift and the bigger tires, did you have to regear your rear axle? I’m wanting to put the same lift, put 33” tires on, but I’m worried that my 3.55 axle can’t handle the tires.
Do you know what color the bottom half of your 2 tone is? Mine is red with that silver and I need to color match the upper piece on my bumper, and I’m sure both silver 2 tones are the same
You would think it's better to use leverage to take off the cap on the wheel and he whips out a half inch flat head💀 anyway you're videos are great I've been watching for about a year now after I got my first truck
I have a truck relatively simaliar to your f150. Mine is also 2wd. And everyone else in my family basically has a bigger/4wd truck. And it irritates me. So I'm gonna have to get my P.o.s a lift kit just to make myself feel better.😂😥
Hey brother what type of lift kit did you used , have the same truck and want to lift 3 inch , so would you tell what branch did u have on yours thanks
@@lmfscrew I was gonna keep back stock and put some 305 70 16 Toyo ATs 2 inch spacers on back. If it's going to casue problems later on I'll spend the extra it's on sell $422 right now with shocks not bad
I’m mostly into older jdm cars but recently purchased a 97xlt extended cab 6 cylinder only though . Came with a snugtop to match. Been following along with your rig build and your truck is dope man. The 9inch lift you added so nice man. Keep up the cool videos🤙🏽
I love this video... You honestly did an awesome job... !!! That truck looks absolutely good...
2018 still the loudest and best sounding 👌🏽
I’ve got 3.5” spindles, 1.5” lift coils, 2” rear lift blocks and 3” body lift sitting on 35s on my 98 2wd. I love it.
Did you have to change anything? Like upper control arms or ball joints?
Got tge same
I love your videos. They are super helpful. I have a 06 f150 2wd and after watching this I may actually go for the spindle lift over a 2.5 level. Was it easy to fit 35s with the spindle lift? Did you have any rubbing or have to do any trimming?
looks good! Larry is coming around pretty quick
If You Add a 3 inch Spacer On The Coil Springs Would It Make Your Truck Higher Than It Is Or Would It Just Reinforce The Suspension Since You Already Lifted The Truck With The Spindles ?
I just bought 3 inch lift spindles for my 97 single cab flareside f-150. I’m excited as hell to put em on
i am about to put a 3in spindle lift with 2in lift coil springs on my 01 2wd gmc sierra... may get drop shackles too
Enjoyed your content!!!
- Your Newest subscriber
Grapps and no cats💪🏻
Makes mo sense
Ford pre-runner! Ground clearance helps in big snow even when you don't have 4wd. I know...believe dat.
Dude 22inch chrome slide would look sooooo beautiful on ths truck
Nice I'm thinking bout lifting mines! Thanks for the Install videos save more money and watch and learn! Awesome like the way f150 sounds!
I can smell drop shackles coming 👌🏻
How much was it?
Did you get a aftermarket longer? Control arm for your truck. Larry.
You mentioned the spindle lift opens the gap of the upper and lower arms .... that’s not how it works it only relocates the the spindle . Otherwise it would mess with the ifs Alignment... some vehicles can have more lift or less from a spindle lift all depends on the factory locations of the spindle on the factory spindle ... like vids keep them coming
I just got one and lovin it. Solid truck. You still got a good lookin truck
Bed line or something similar on the whole truck would be dope. Whatever you do can’t wait to see the build👌🏽
Hell yeah that’s hard , I’m deff installing one on my mine !
You put on them blocks too or just shocks and spindles ?
So the kit came with rear struts as well. Did you put blocks in the rear? Or does it kind of level it without the blocks? Are the rear struts okay to put in without putting in the rear blocks?
I’m putting the same lift on my 2002 Ford F-150 2WD and I’m having trouble removing the stock spindles. I’m beating the hell out of it to try getting it out. Any recommendations? 8:45
Wheels+tires
restore those headlights
tint
New headlights and wheels and tires an tow mirrors 👍💯
Very cool and can’t wait to do this too my truck. So are these just stock springs on your truck?
My current setup is cut springs and lowered, very sick of this rough ride and setup. I see the 3” lift kit on the rough country website but they only offer the 2” leveling kit springs? Should I purchase these over stock or?
Why is the stock tail lights on baby squat ?
Hi I just found you Video
And got cuestión
On back disc not have to have the cap for grease??
That ford is lookin good
Excited to see the upcoming wheel setup
You should get new headlights and grille soon that would make it menacingly clean 🤘🏻🤘🏻
Hey bud I found a 5.5in spindle lift from spindlesource what would I have to change other then the spindles?
where is the dust shield that was removed? did you reinstall?
I’m about to do complete brakes suspension and steering all around on my 99 f150 4.6 2wd
Im in the same boat with same engine.
I just need to pull the trigger already and get my kit.
@@maxz4065 I did the lift and everything else while I was down there. took about 5 hours with a knowledgeable friend and lots of tools. I fell in love with the truck all over again. new tires and took her in for an alignment. like riding brand new
@@Elon_Trump any pics
@@Elon_Trump how did effect your gas mileage?
@@ernievilla6840 not bad at all or at least not very noticeable I also check the tires once a month or so to keep them at proper pressure. She is still on the road and drives great.
Ford sounds good. I have the exact setup on my truck that is similar to it. But Baby Squat sounds better. Man that is a good looking truck and she fits her looks
Since you added the spindle lift your front sticks out more then the back.
I currently have 2” loaded struts could I add a 3” spindle?
did you spin and torque the rotor properly to seat the bearing? doesn't look like you did from the video.
I just bought mine I’m waiting in the mail
Can't wait to see what you do to this one, looking forward to the crazy transformation lol
How did you find what to torque everything to? Or could you just tell me what torque you used? I've looked online and get a bunch of different answers and would just like to know what you used for all the bolts
I like the teal green color truck
How much was this lift I have the same Ford
After the 3” spindle lift and the bigger tires, did you have to regear your rear axle? I’m wanting to put the same lift, put 33” tires on, but I’m worried that my 3.55 axle can’t handle the tires.
Did you put any blocks in the rear or is the rear completely stock? I really want to do this but I have a completely stock 2001 F150!
Just installed this on my 03 and now I’m having a rubbing sound which sounds like my abs sensor is squealing. Any issue with this for you?
hey what's the rim order number for 'ol larry.? I want the same but can't find them,thanks
Did u put on the blocks in the back or did u leave it the same
So do I need to do anything to the bed of the truck also or the splindle just lifts up everything? I have the same truck.
Let that tire rub and beat the box for koonce #longlivekoonce 🙏🏾❤️
Just found your channel love watching the Larry episodes. How far out did this spindle lift move the tires out from the body?
Do you know what color the bottom half of your 2 tone is? Mine is red with that silver and I need to color match the upper piece on my bumper, and I’m sure both silver 2 tones are the same
Can I run F-150 parts on an expedition (same year range and both 2wd)
Always enjoy your content. Thanks, sir!
I just lift my 03 Silverado 3inch the same way looks great
Larry looking good leaning like that needs to be lower in the back tho love the video's keep up the great content 🤙🇺🇸
Is there a spindle for a 2018 Chevrolet Silverado 2WD that doesn’t require new rims
Did you use the rear shocks that came with the new kit ? I want to buy the same kit but only want to install the front
I got 98 2wd same lift but a 3 inch body lift also clears 20x12 and 33s
Hey ask the shock absorbers are the same size new as used. Excuse me
Did you not install the blocks in the back?
Where can I buy that kit !!?? Thanks for the vid!!!
Did you install the rear blocks or left the rear stock?
where did you get the parts?
I have a 2011 duramax and think I like your 1500 more then my d max. How does it feel power wise to compared to the d max?
I have no complaints with the power, id test drive some. Def not as much torque as you might be used too though.
Did u have ABS sensor rubbing slightly
on spline after. I notified mine doing it, trying to figur out what to do
Im about to do the spindle lift do i have to get another kind of larger shocks? Cause i just had all mine changed out 2 months ago
Did you have to shave off the lower Control Arms for the lift spindles to fit?
No
You live in bama same man
You would think it's better to use leverage to take off the cap on the wheel and he whips out a half inch flat head💀 anyway you're videos are great I've been watching for about a year now after I got my first truck
I have a truck relatively simaliar to your f150. Mine is also 2wd. And everyone else in my family basically has a bigger/4wd truck. And it irritates me. So I'm gonna have to get my P.o.s a lift kit just to make myself feel better.😂😥
What is the best lift for a ‘01 f150 lariat ? That isn’t super expensive
How big of a wheel spacers did you end up putting in the rear
Drop shackles offset and graps😻
could I run a 5 inch rough country lift for a four-wheel-drive on my 2000 model F150 but I have a 2w
How long have u had larry and how many videos have u made with it?
Just did this lift but when i hit around 70 its get pretty bumpy. Any thoughts?
What year is Larry?
Hey brother what type of lift kit did you used , have the same truck and want to lift 3 inch , so would you tell what branch did u have on yours thanks
@imfscew do you have to get new shocks when you install any spindle lift?
Nice truck,how much lift in the back
But this was a helpful video. Thank you👍
Cant wait to see it with new rims and tires !!
We’re did u buy kit from
I got a 2000 long bed f150 2wd single cab 55k miles. Do I NEED the shocks from rough country or can I just get spindles and it be alright. Thanks
With the low miles you probably don't have to, but the rc ones are longer and made for the spindle lift.
@@lmfscrew I was gonna keep back stock and put some 305 70 16 Toyo ATs 2 inch spacers on back. If it's going to casue problems later on I'll spend the extra it's on sell $422 right now with shocks not bad
Lift a 2WD ??? whats the matter....speed bumps at the WalMart too high ??
So question I already have strut spacers 3 inch can I buy spindles to and install them to or will that cause problems
The Pizza Man I have that setup it works fine and looks great
does it need a steering stabilizer
Do you have to get a alliment after
What size tires were on it I this video?
New headlights taillights and wheels and tires👌🏻
Looks great man!
No block install ? 😮
What do you recommend for a 2000 f150 4x4 lift?
Clear headlights and Mud Grapps.... just some ideas
thought that hammer would hit me
Will this work on a 1991 F150
Looks great. Gonna attack this over the weekend
Where did you get your taillights on your Silverado?
Can you make a vid on what your all gonna do to the truck.
Could you fit a 2.5” leveling kit with the spindle lift without lower control arm relocation?
Yes i have seen people do it i dont recommend it though unless you are used to driving with stiff front suspension.
I enjoyed this informative video. Thank you