B18 Swap Parts List and Guide || Engine Swap Parts List

แชร์
ฝัง
  • เผยแพร่เมื่อ 5 ต.ค. 2024
  • B18 Swap Parts List and Guide || Engine Swap Parts List is compiled to help anyone with a Civic engine swap or and honda engine swap that they are looking to complete. I'm not drag racing, but I will say this thing rips due to being lightweight and Honda should have put the B18 swap into all honda civic hatchback of this era. Truly changes the whole character of the car and the fitment is spot on.
    "Project Civic" Parts listed below w/ option numbers. This applies for B18C, B16a, B16B, B18a, B20, etc
    Hit SUBSCRIBE and turn on Notifications for new videos! - goo.gl/LLojcS
    Time to run through all of the parts I used to swap a OBDIIa B18C engine from an Acura Integra GSR into a OBDIIa Civic DX hatchback.
    Subscribe to Follow My Build! - goo.gl/hi9yB2
    Hondapartshero harness - goo.gl/fguxyK
    Civic SI T Bracket - goo.gl/iTB1WY
    B20 CRV 2 post Bracket Mount
    Or goo.gl/JHzdTK
    Civic DX Transmission bracket and mount
    Civic DX Clutch hard line on engine and transmission bracket mount
    Or Engine Mount Kit - goo.gl/dBcEKc
    Integra GSR upper/lower Radiator Hoses - goo.gl/79lKgj
    Integra GSR heater hose - goo.gl/uXiRwA
    Yonaka exhaust - goo.gl/t8sW0u
    This guide was hopefully thorough enough for all performing a civic swap with an OBD2 start. I am planning to create the honda engine swap guide for other Honda civic chassis and OBD1, 2 cars. The wiring is really all that changes. To complete this build, the honda civic swap cost is actually very low for anyone looking for a fun budget civic project car.
    "Project Civic" Hatchback Build Episodes:
    Episode 1: goo.gl/2ZWgT1
    Episode 2: goo.gl/Uk23aC
    Episode 3: goo.gl/knN406
    Episode 4: goo.gl/JsGwAv
    Episode 5: goo.gl/9S1XFn
    Episode 6: goo.gl/D3Bxfy
    Episode 7: goo.gl/Trz5xc
    Episode 8: goo.gl/26iosP
    Episode 9: goo.gl/u00iAI
    How To Compression Test: goo.gl/kqVwdi
    Swap Integra Seats into a Civic EK: goo.gl/HvuZ2r
    B18C Swap Parts || Civic Hatch How To : goo.gl/7eahQe
    Honda B18C Engine Swap Update and Pulls: goo.gl/21PGD5
    Flipping Car Parts On Ebay And Craigslist: goo.gl/9VQpoN
    Welcome to Stauffer Garage! I am beginning an EK civic project car build and will be documenting the entire process vlog style along with tutorials and updates. I have picked up an Integra GSR for cheap and will be pulling the B18C and all other components that will fit and putting them onto my Civic. Goals for this car are to make it daily but it will be primarily a track day weapon! Boost might come into play along with other mayhem! Not a drift car build, but this will certainly be closer to a race car build when all is said and done for this little hatchback
    Be sure to subscribe to follow along with this build and the other projects that come along!
    Business Inquiries: thestauffergarage@gmail.com #stauffergarage
    #carcleaning #cardetailing #powerwashing #maddetailing #ammonyc #thedetailgeek #detailgeek #wddetailing #autodetailing #disasterdetail #detailing #interiorcarcleaning #carcleaning #interiordetail #filthycardetailing

ความคิดเห็น • 222

  • @pandamike209
    @pandamike209 6 ปีที่แล้ว +48

    throttle cable on big thing u forgot

    • @StaufferGarage
      @StaufferGarage  6 ปีที่แล้ว +14

      Yes you are correct thanks for adding

    • @ap3xguardian121
      @ap3xguardian121 4 ปีที่แล้ว

      yes i used an itr throttle cable with my swap

    • @keapeer6669
      @keapeer6669 3 ปีที่แล้ว

      Is this for every b-series swap? Sorry I’m a noob also this this go with any b series swap?

  • @CeeJaay300
    @CeeJaay300 8 ปีที่แล้ว +43

    yes do a obd1 - 2 swap talk

    • @bradlyfan
      @bradlyfan 6 ปีที่แล้ว +3

      crisJv I did it once want my advice?

    • @jrentas3239
      @jrentas3239 5 ปีที่แล้ว

      Agreed

    • @linglingz3322
      @linglingz3322 5 ปีที่แล้ว

      Yes

    • @olivermoes-okun2468
      @olivermoes-okun2468 4 ปีที่แล้ว

      @@bradlyfan I have b18b1 from 97 Integra and putting in my 00 civic dx hatchback. what ecu should I use? I have d16y7 harness on and a obd2 to obd1 harness so I can convert to obd1 if that's better

  • @youtang
    @youtang 6 ปีที่แล้ว +6

    Hey I just remembered that your videos really helped me out with my GSR swap. Your videos were the most well put together in regards to the B18C swap. Thanks to your videos and some really well written forum write ups, I was able to start up on the first crank. The only CEL was there for not having the first o2 sensor plugged in...the exhaust manifold on the 94-99 GSRs are too short and the flanges are postioned differently. Anyways, thanks again!

  • @cheeseburguhgaming9581
    @cheeseburguhgaming9581 2 ปีที่แล้ว +1

    yeah i was debating to engine swap my car too but i was like forget it ecu getting vtec chipped or getting a s2000 hondata t brakets and all these other things i rather just throw some arp head studs ungraded cams and turbo the car clean the engine grime and have a turbo exhaust adaptor to bolted on to my exhaust axle back and muffler

  • @buildhumbly7905
    @buildhumbly7905 7 ปีที่แล้ว +5

    Brother thank you! I've been wanting to do a gsr swap on my ek so this is gonna help a ton! 👍🏼

    • @StaufferGarage
      @StaufferGarage  7 ปีที่แล้ว

      Happy to help! Let me know if you have any questions!

  • @missle5026
    @missle5026 8 ปีที่แล้ว +1

    Thank you for the vid I have a 2000 civic Dx hatch that I plan on doing a b18c swap on and this vid helped a lot!

  • @TheWorteldrie
    @TheWorteldrie 7 ปีที่แล้ว +3

    Ive got an LS swapped 97 civic EX and it runs good but the check engine light is on (which I'm not freaking out about) and I'm sure I did something wrong lol. Vtec wiring harness to non vtec motor. Lots of plugs left hanging..

  • @SAViOR13100
    @SAViOR13100 8 ปีที่แล้ว +2

    Interesting that you used the d16 radiator, mine seems to be too small for my hoses.

    • @SAViOR13100
      @SAViOR13100 8 ปีที่แล้ว

      As far as the bungs that come out of the radiator itself

    • @StaufferGarage
      @StaufferGarage  8 ปีที่แล้ว +2

      +REAMS 2 I reused the d16 clamps on the gsr hoses and it sealed great and haven't had any issues at all

    • @SAViOR13100
      @SAViOR13100 8 ปีที่แล้ว +1

      Stauffer Garage I see I see. I just feel like getting a new one since my d16 overheated too many times so I figure get a fresh one

    • @StaufferGarage
      @StaufferGarage  8 ปีที่แล้ว +1

      +REAMS 2 mine was less than a year old and I didn't want to just toss it. If you are in need of a new one pick one up!

  • @killer1cam606
    @killer1cam606 4 ปีที่แล้ว

    Shift linkage b series you'll need that too

  • @cruzperez9452
    @cruzperez9452 4 ปีที่แล้ว +1

    What about for a 1999 Honda Civic EX with a D16Y8? Do I need anything more or less?

  • @levonlyons
    @levonlyons 2 ปีที่แล้ว

    I know I'm old but I still want to do a Jdm engine switch I need to get all the cash to make this come to my life goal its either this or a luxury built car

  • @djsonicc
    @djsonicc 6 ปีที่แล้ว +1

    Tons of information. I don't understand why people are disliking?

  • @ej8mods160
    @ej8mods160 2 ปีที่แล้ว

    Thanks you so much for the detail video your the best 👍🏻

  • @jimboi7616
    @jimboi7616 8 ปีที่แล้ว +2

    Interested for a vid on a jdm gsr b18c into an ek. I have researched this online and have a good grasp on how to do it, but I would like to have your input as well. Btw, Keep the build vids coming dude! 👍🏽

    • @StaufferGarage
      @StaufferGarage  8 ปีที่แล้ว +1

      +Jim Boi thabks a lot! I can look into it but know the biggest difference is in the crank position sensor on the front. You need to bypass or switch the oil pump to a hadn't version and add the sensor

  • @tubejim101
    @tubejim101 7 ปีที่แล้ว +1

    Thank you for making this video.

  • @chulohernandez8521
    @chulohernandez8521 5 ปีที่แล้ว +1

    Im going wit a B18b1 in my 98 dx but it isn’t vtec and the dx obvio none vtec can i also use that harness or would have to just find the harness and I also have a ex harness fully un cut Lmk

  • @monstahtron
    @monstahtron 7 ปีที่แล้ว +1

    very informative video saving this for whenever my d16 blows lol

    • @StaufferGarage
      @StaufferGarage  7 ปีที่แล้ว +1

      Lol, I couldn't wait for mine to do that! Wasn't going to happen for a long time!

    • @codcade
      @codcade 2 ปีที่แล้ว

      Same lol, just got a free hatch lol,
      Has a d16y7 and it’s got 287k and just eats oil lol

  • @nilbog3641
    @nilbog3641 3 ปีที่แล้ว +1

    Any recommendations for an ef hatch

  • @jimhiscott2918
    @jimhiscott2918 2 ปีที่แล้ว

    Ditch obd2. Always go obd1

  • @kodyking3090
    @kodyking3090 3 หลายเดือนก่อน

    All that work and extra parts for a 290hp motor?

  • @samueltaladay8890
    @samueltaladay8890 3 ปีที่แล้ว

    I have a 2003 Civic 4 door 5 speed. Need more power and need help

  • @SamyyCJR
    @SamyyCJR 10 หลายเดือนก่อน

    what parts would have to be different in order for this to work with an EG 1992 hatchback ?

  • @3030rey
    @3030rey 5 ปีที่แล้ว

    Something more can change on plugs, like idle plugs alternator plugs ignition plugs ?

  • @dkinley334
    @dkinley334 3 ปีที่แล้ว

    My dream is to b18 swap my ek sedan but dang it seems like such a job

  • @salvadordelgado4983
    @salvadordelgado4983 ปีที่แล้ว +1

    Hey man, i recently bought a 76 cvcc and my motor is no good, been thinking about doing an b18c swap but i have absolutely no knowledge of swapping engines, is there any tips or specific websites that i can look at ??

    • @StaufferGarage
      @StaufferGarage  ปีที่แล้ว

      Honda-tech has everything you’ll need from diagrams to step by step posts

  • @see012392
    @see012392 10 หลายเดือนก่อน

    did you keep the powering steering? what did you use for the power steering backet if you did?

  • @frankmanzur5904
    @frankmanzur5904 5 ปีที่แล้ว

    I have I 96 civic with a 97 b18c jdm and jdm p72 motor in it but body is trash ,so and im going to strip everthing from that car to a 2000 civic coupe automatic whats the best harness to get on a budget

  • @peterboyles5376
    @peterboyles5376 7 ปีที่แล้ว +1

    Thanks for the video and I have a 1999 Honda Civic ex with a D16y8 VTEC and can I just use the harness from the D16Y8 to the B18C

    • @StaufferGarage
      @StaufferGarage  7 ปีที่แล้ว

      Essentially yes, if it already has vtec. The only thing missing would be the wiring for the dual runner manifold on the B18C

  • @loganhoward4599
    @loganhoward4599 3 ปีที่แล้ว

    Sorry so why do you need the d16 harness? I'm buying a package that includes the entire wiring loom for a b18c so i should just use that right ?

  • @1BadRAMLimited
    @1BadRAMLimited 2 ปีที่แล้ว

    Thanks

  • @mrsemifixit
    @mrsemifixit 3 ปีที่แล้ว

    Can you just swap stock ECUs or need something else?

  • @ivtecudont241
    @ivtecudont241 7 ปีที่แล้ว

    Thanks for the informative video .. and yay looks like I'm pretty set for my swap this week 😁

    • @StaufferGarage
      @StaufferGarage  7 ปีที่แล้ว

      How'd the swap go?

    • @ivtecudont241
      @ivtecudont241 7 ปีที่แล้ว

      Stauffer Garage going to be dropping the y7 and installing everything on Friday, it's going to be a long day but everything SHOULD go as planned .. I'm excited

    • @StaufferGarage
      @StaufferGarage  7 ปีที่แล้ว

      +ivtecudont241 You'll encounter a few things but its straight forward to be honest

    • @ivtecudont241
      @ivtecudont241 7 ปีที่แล้ว

      Stauffer Garage I'm sure , nothing goes correctly as planned ... now because I'm dropping in a jdm b20 block(GSR head) it has no ckf so I gotta do the ckf bypass trick .. technet.ff-squad.com/ckftrick.htm
      I still need the upper radiator hose and I think I might get the thermostat as per your recommendation ..(I'm doing the timing belt water pump etc etc as well)

    • @ivtecudont241
      @ivtecudont241 7 ปีที่แล้ว

      Stauffer Garage remember you said I'd run into something ? I did.... my b20 did have a dented oil pan and the oil pickup was bent ... (had a junk GSR block laying around so I was gonna use that for some donor parts) so yeah I dropped the oil pan after I drained the oil from the b20V andddd metal sediments galore ... metal shavings galore ... that little time that the car had running with the damaged oil pick up wreaked havoc on the bearings ... because it's a low mileage jdm block the crank is good but the bearings took the hit .... gonna junk the block or save it and build that but for now gonna get a high compression b20 block and throw my vtec head over .. on that

  • @khyrone5193
    @khyrone5193 4 ปีที่แล้ว

    Wondering if the B18C engine is a good engine swap for a Peugeot 205 GTI

  • @rickarchibald1369
    @rickarchibald1369 2 ปีที่แล้ว

    This really helped!

  • @speedybede4639
    @speedybede4639 3 ปีที่แล้ว

    Okay so, I’m planning to do a B18C2 Swap on my 1st gen CRX si(1985)… after some research I realize that OBD-1 was introduced to the us market in ‘92. Will this cause me trouble if I’m OBD-0 on my ECU?

  • @dreamer2355
    @dreamer2355 8 ปีที่แล้ว +3

    It would have been nice if you covered the exhaust setups too such as if anything is plug and play or if welding needed to be completed. :)

    • @StaufferGarage
      @StaufferGarage  8 ปีที่แล้ว +2

      +AutoTechDale thanks for the suggestion! Will do in the next review and do a full walk around of the civic and discuss

    • @dreamer2355
      @dreamer2355 8 ปีที่แล้ว

      Stauffer Garage That sounds great. Its very hard to find the correct information out there on what to do with your exhaust after a swap seeing as the B series manifolds are different lengths

  • @justinmangubat7764
    @justinmangubat7764 5 ปีที่แล้ว

    I have a 1996 B18C1 engine and I'm hoping to put it in my 1991 Civic Si. What parts should I be getting? Any tips aswell? Thanks!!

  • @JamesJonahJameson-MM
    @JamesJonahJameson-MM 2 ปีที่แล้ว

    Did you ever make a video for OBD1 to OBS2 swaps? I live in CA and I’m beginning to collect parts for a 1999 B18C5 that will go into my 1992 Honda Civic CX non Vtech hatch. I will be buying the ATK remanufactured B18C5 engine. 4 month waiting list.

  • @h23beltran24
    @h23beltran24 8 ปีที่แล้ว

    yes do a obd1

  • @anthonyorozco452
    @anthonyorozco452 5 ปีที่แล้ว

    please make a video with obd2 for a swap obd1

  • @marcialgarcia112
    @marcialgarcia112 4 ปีที่แล้ว

    What about the trasmission torque mount ? I got the 99 ek hatch but the stock mount doesnt work looks too big.

  • @WexfordGamingNetwork
    @WexfordGamingNetwork 4 ปีที่แล้ว

    I have a dc1 integra. (1.6L non VTEC) , what exactly do i need? Or any tips? As obviously the chassis etc is the same as the dc2 , so its just the Loom , ecu , mounts , and?..

  • @aaronpitts2762
    @aaronpitts2762 8 หลายเดือนก่อน

    Hi, will this apply to the eg6 civic?

  • @ThePrelude1999
    @ThePrelude1999 3 ปีที่แล้ว

    I'm thinking about doing an engine swap a b series maybe b16c or b18b1 engine in my civic butts it's a 2000 civic ex Is it possible?

  • @bigt_money615
    @bigt_money615 5 ปีที่แล้ว

    im guessing that all this applies to a 96 EJ

  • @DamonPlayss
    @DamonPlayss 2 ปีที่แล้ว

    Would this work for a LX sedan ?? I have a 97 and I’m looking to b18 swap mine as well

  • @EddieSwaggy
    @EddieSwaggy 2 ปีที่แล้ว

    Hey man thanks for the video! I just did a b18c swap as well and i'm having fuel issue did you have to change your fuel pump?

    • @bootzmckenzington
      @bootzmckenzington 2 ปีที่แล้ว

      Having the same issue. Mine is running lean . Looking into gsr fuel pump. Might be your issue to

  • @michaelwilliams6922
    @michaelwilliams6922 5 ปีที่แล้ว

    Can't you just take out the d series harness and put in the b series harness and get the right b series ecu

  • @3030rey
    @3030rey 5 ปีที่แล้ว

    What change if I want to to do swap but my civic is obd2b what change if the b18c dc2 is obd2a I can do the jumper on the ecu to run obd2a or p28

  • @adrianreyes330
    @adrianreyes330 7 ปีที่แล้ว +1

    I have a 1998 civic dx, what engine series do you recommend swapping it with? I want to swap it with a b18 or b20

    • @StaufferGarage
      @StaufferGarage  7 ปีที่แล้ว +2

      B18C all the way. Its the highest displacement B-series with vtec and they will run forever and take abuse.

  • @louiselorenzo9458
    @louiselorenzo9458 3 ปีที่แล้ว

    What is the motor on the brake for that?

  • @leviorourke7498
    @leviorourke7498 4 ปีที่แล้ว

    Will this parts list be accurate for the 1990 ef civic si I have

  • @stevensweets805
    @stevensweets805 6 ปีที่แล้ว

    Hello sir, I have trouble with the connecting the wiring harness, please show how you did it. I have a p3x ecu currently installed. It only has 2 plugs while the p72 I have has 3 please help

    • @stevensweets805
      @stevensweets805 6 ปีที่แล้ว

      Also, did you swap distributors because my GSR plug is different from the D14s distributor

  • @benmontgomery5608
    @benmontgomery5608 4 ปีที่แล้ว

    Can you do a b swap to a 2002 4 dr ex civic

  • @marcialgarcia112
    @marcialgarcia112 4 ปีที่แล้ว

    Help please i am having problems with my 96 gsr swap into my 99 ek hatch,
    The ecu coneccion on the ecu its different from my ek civic,
    I bought a obd2b-obd2a jumper harnes but still cant fit 😥

  • @luisramos2737
    @luisramos2737 7 ปีที่แล้ว

    Nice videos...Did you upgrade your fuel pump? I have the same setup but it seems like my stock fuel pump is not flowing enough fuel. I'm thinking of upgrading to 255 walbro fuel pump. Let me know ur opinion thanks

    • @StaufferGarage
      @StaufferGarage  7 ปีที่แล้ว

      No, and I would doubt that you would need an upgraded pump unless your pump is going bad. The stock pump can flow plenty of fuel and if anything you could upgrade your fuel pressure regulator and adjust that pressure to flow more through your injectors first if you truly have the same setup as me.

  • @christophersmokeyday622
    @christophersmokeyday622 3 ปีที่แล้ว

    I just bought a b18b1 and trans with “stage 3 clutch” for $200 bucks. It was previously in a 97 ek civic. How can I tell if it is the correct obd for my 2000 civic? I have a stock d16y8 ex sedan

    • @christophersmokeyday622
      @christophersmokeyday622 3 ปีที่แล้ว

      I’m only 19 and I’m new to all of this stuff. quarantine has me bored so I want to start learning new stuff. bought all the tools I need! just need to learn it all now lol

  • @Fukushuu-u7z
    @Fukushuu-u7z 4 ปีที่แล้ว

    What throttle cable do I use?!?

  • @chriscole9621
    @chriscole9621 3 ปีที่แล้ว

    What else do I need to do a d16 auto to a b series manual?

  • @jcreary100
    @jcreary100 6 ปีที่แล้ว

    i have a 1999 honda civic lx d16y7 tubo, i would like to swap in a b16a sir ek9 and i would like to keep it obd2 for emissions purpose, what do you recommend. any help would be thankful.

  • @VietTranHB
    @VietTranHB 7 ปีที่แล้ว

    Can we passed on Smog check ? I heard that we can make swapped engine legally whenever the emissions pass the government's requirements

    • @StaufferGarage
      @StaufferGarage  7 ปีที่แล้ว +1

      Yes if you retain all the charcoal canisters and swap everything over from a GSR front clip.

  • @alexmartinez-vj3eq
    @alexmartinez-vj3eq 4 ปีที่แล้ว

    Is d16y5 harness plug and play on b18b1

  • @tubejim101
    @tubejim101 5 ปีที่แล้ว

    How can I bolt in the power steering pump? b18c1 going into 98 EX Civic. Have the gsr brackets, and pump, but the high pressure hose does not hook up. Thinking I need a ps pump from a 99 SI??

    • @StaufferGarage
      @StaufferGarage  5 ปีที่แล้ว

      No you can reuse the Civic pump. Just need a bracket from the CRV B20. Check on Honda-tech and search for the exact one. I was able to reuse the entire Civic PS system.

  • @marcialgarcia112
    @marcialgarcia112 4 ปีที่แล้ว

    So If i got the to b20 crv post mounts i shouldnt need to buy any adicional mounts right ¿
    Its a 99 ek.

  • @quinceyclements2244
    @quinceyclements2244 4 ปีที่แล้ว

    Will these parts work on my 98 EJ

  • @cosmicfiber4
    @cosmicfiber4 5 ปีที่แล้ว +1

    I’m going with a B18C1 into 96 del sol. Anybody done this? anybody know of anything additional craziness special for del sol?
    Also, is anything special needed for gauges/tachometer? Like a different tachometer, do engines have different redlines and what not?

    • @fourside4237
      @fourside4237 2 ปีที่แล้ว

      Hey dude this is late but did you ever figure this out?

    • @TheRichardOlson
      @TheRichardOlson ปีที่แล้ว

      Same, im stuck on the rear t bracket atm

  • @luisaguilar-kh1se
    @luisaguilar-kh1se 6 ปีที่แล้ว

    Please make the obd1 into obd2 please

  • @Georgio_619
    @Georgio_619 4 ปีที่แล้ว

    How easy is it for a del sol b16a3

  • @tubejim101
    @tubejim101 7 ปีที่แล้ว +1

    Is the B20 CRV 2 post Bracket Mount, an OEM part? Having trouble finding the OEM part number.

    • @StaufferGarage
      @StaufferGarage  7 ปีที่แล้ว +4

      I think this is it: 1910-P3F-000
      I grab mine out of the junkyard from a CRV.
      www.bernardiparts.com/Honda/Parts-List.aspx go to like a 98 crv ex 5 spd under the engine:cylinder block/oil pan section

    • @tubejim101
      @tubejim101 7 ปีที่แล้ว +1

      Thank you.

    • @danielstephens4420
      @danielstephens4420 5 ปีที่แล้ว

      This is wrong ! Crv post is too tall.Make motor sit slanted down about 2 inches on one side.You want the 99-00 si post mount.

  • @marseanf3039
    @marseanf3039 4 ปีที่แล้ว

    For the ac what belt do you use?

  • @seavick7001
    @seavick7001 7 ปีที่แล้ว

    Yeah I have a obd1 gsr and have an ek as well need help asap

    • @StaufferGarage
      @StaufferGarage  7 ปีที่แล้ว +1

      will look into this and try to throw a tutorial together!

  • @prashanthperananthasivam3416
    @prashanthperananthasivam3416 6 ปีที่แล้ว

    I have a non vtec 00 ek obd2b but have a obd1 97 gsr what harness do i use

  • @chrisasaurus
    @chrisasaurus 5 ปีที่แล้ว

    B swap on a 79' cvcc Honda

  • @nichigd6863
    @nichigd6863 ปีที่แล้ว

    If I have an integra ls 1998 does it slide in or do I need any other parts ?

    • @StaufferGarage
      @StaufferGarage  ปีที่แล้ว

      You will have it easier but there are some parts that will be needed that you can get out of the oem honda parts bin

  • @luisramos2737
    @luisramos2737 7 ปีที่แล้ว

    Hi James

  • @keithbegley888
    @keithbegley888 7 ปีที่แล้ว

    Is it the same with the coupe, are the engine bays different hatch vs coupe?

    • @StaufferGarage
      @StaufferGarage  7 ปีที่แล้ว +1

      Nope! Even the 4doors are all the same front end :)

  • @fullcoverage5305
    @fullcoverage5305 6 ปีที่แล้ว

    Putting a 94gsr in my 00gsr. What will I need for the conversion? Since I would be going from obd2 to obd1? Or should I keep everything obd2 by switching everything over to the new motor

    • @danielstephens4420
      @danielstephens4420 5 ปีที่แล้ว

      Or just screw adding the oil pump,ckf senor and new timing gear....and just do the ckf wiring bypass.It works 100% I've done it on at least 10 swap.

  • @reddragonx8799
    @reddragonx8799 6 ปีที่แล้ว

    I'm trying to swap my engine to a B18 I have a 2000 Honda DX what parts do I need to be able to swap my engine with a B18?

    • @StaufferGarage
      @StaufferGarage  6 ปีที่แล้ว

      I would re listen to this video and what year is the motor?

  • @Joliva124
    @Joliva124 ปีที่แล้ว

    What about for the power steering I'm doing a swap and I have a d16y8 and if there someone that can help me what to do get an idea I would appreciate it!

    • @cheesus9744
      @cheesus9744 ปีที่แล้ว

      I’ve heard you need a em1 si p/s pump and your stock obd2 ek power steering lines

  • @livinglargeandfree8322
    @livinglargeandfree8322 7 ปีที่แล้ว

    I'm gonna do this in my 98 crv

    • @StaufferGarage
      @StaufferGarage  7 ปีที่แล้ว +2

      YES!!! That is something I want to do and boost it! Sleeper!

    • @livinglargeandfree8322
      @livinglargeandfree8322 7 ปีที่แล้ว

      that's what I was thinking...but mine is also lifted.

  • @henryfilip4325
    @henryfilip4325 5 ปีที่แล้ว

    Does anyone know if this is the same for doing a b18 swap into an ep1 chassis?

  • @josephquintana1970
    @josephquintana1970 5 ปีที่แล้ว

    What’s the difference between b18c and b18c5? Do both of type r engine apply to this video or they slightly different

    • @brrbrr474
      @brrbrr474 10 หลายเดือนก่อน

      4 years later im doing my first civic swap with a b18c i did some research and figured out the b18c is the jdm verison and the c5 is the usdm verison. the only difference comes with the match transmissions. the final drive is shorter on the jdm verison.

  • @101009pm
    @101009pm 6 ปีที่แล้ว

    I noticed you swapped into a non vtec chasis civic. How did you get your iacv to work? Did you reuse your old throttle body?

    • @StaufferGarage
      @StaufferGarage  6 ปีที่แล้ว +1

      In the harness I recommended it includes wiring for the IACV that you run back to the ecm

    • @danielstephens4420
      @danielstephens4420 5 ปีที่แล้ว

      Or just use your harness and search 3 wire iacv to 2 wire online.You just depin one wire and depin and relocate one wire on your harness ecu plug.Takes 5 minutes.

  • @radrepairs3134
    @radrepairs3134 ปีที่แล้ว

    having trouble with the gsi tranny shift linkages, it not shifting into 3 or 4. any suggestions?

    • @StaufferGarage
      @StaufferGarage  ปีที่แล้ว

      Can it shift in the other gears no problem?

    • @radrepairs3134
      @radrepairs3134 ปีที่แล้ว

      @Stauffer Garage its damaged internally, Thanks for the reply mate, really appreciated.

  • @markozettl6541
    @markozettl6541 7 ปีที่แล้ว

    hi, im interested about a swap b18 vti on my currently d14a4 97 civic hatch...is that possible and what I need to prepare to have to install that swap? Best reguards (Y)

    • @StaufferGarage
      @StaufferGarage  7 ปีที่แล้ว

      Probably the same parts I have listed. The only differences will be around the wiring depending on the emissions level the car and motor are at.

  • @Cardmonger
    @Cardmonger 7 ปีที่แล้ว

    If i had an ls. And say i wantes to just do a gsr swap. Would al i need be the engine, ecu, and the gsr wire harness? Or do i need pig tails also?

    • @StaufferGarage
      @StaufferGarage  7 ปีที่แล้ว

      Engine Ecu and reuse the LS harness, you would just need to add the harness I have linked in the description box for vtec, dual intake manifold and crank sensor.

  • @bull7618
    @bull7618 7 ปีที่แล้ว

    What if it's a d14 ek series civic? know anything about wiring for a conversion in that case?

    • @StaufferGarage
      @StaufferGarage  7 ปีที่แล้ว

      It should be pretty much the same and just add in the harness I suggested in this video for Vtec and dual runner manifold found on the GSR B18C engine

  • @loveheraye408
    @loveheraye408 6 ปีที่แล้ว

    I’m swapping a obd2a b18b1 into my obd2b 00 ex civic will it be plug n play? Or will I have wiring issues

    • @StaufferGarage
      @StaufferGarage  6 ปีที่แล้ว

      You will have to do a couple wire changes I believe. Search on Honda-tech.com

  • @EdithSanchez-qe4hz
    @EdithSanchez-qe4hz 6 ปีที่แล้ว

    Whats the best swap for 91 acura integra

    • @youtang
      @youtang 6 ปีที่แล้ว

      If you're lucky, you find a B17. Or, try looking into building a LSvtec.

  • @datbenzdoe5157
    @datbenzdoe5157 7 ปีที่แล้ว

    So I have a da9 and I just got a obd2 gsr and am about to do the swap as far as I've read it's basically a direct swap besides the dual runner intake manifold which I already bought a skunk2 manifold and 70mm throttle body and I need a p28 or p30 ecu so I need to wire the vtec but I got a vtec wire kit and I believe that's it correct? Thanks.

  • @blix8787
    @blix8787 7 ปีที่แล้ว

    question. so when you put the b20 ac bracket did you use the b20 pulley or did you use the d16 pulley. reason why I went to my local junkyard and they only had one crv that had the bracket taken off already but it was missing the pulley. today being Thursday I have to wait till the weekend to see if I can swap it over but I would like some reassurement

    • @StaufferGarage
      @StaufferGarage  7 ปีที่แล้ว +1

      Actually they should be identical, at least it was for me! the one on the B20 bracket had bad bearings and I swapped on the D16 one and been running no issues. Visually they looked identical so I ran with it.

    • @blix8787
      @blix8787 7 ปีที่แล้ว

      Stauffer Garage awesome. thank you very much. I'll do the same. Also keep up the videos I gotta say I found your videos better informed than those from Honda street garage.

    • @StaufferGarage
      @StaufferGarage  7 ปีที่แล้ว +1

      Glad to hear and glad you are enjoying my content! Always open to suggestions and fyi tonight new video will be out! First episode of the Summer detailing series!

    • @blix8787
      @blix8787 7 ปีที่แล้ว

      Stauffer Garage awesome I'll check it out as soon as I get out of work.

  • @cjnunez8426
    @cjnunez8426 7 ปีที่แล้ว

    about how much would i spend to do this set up on my 99 ex and put a 99 gsr? im not a mecanic im not sure how much it will cost? thats what im trying to figure out thanks.

    • @StaufferGarage
      @StaufferGarage  7 ปีที่แล้ว

      Would you do the labor yourself? Free!!!! Check out on Craiglist for a 99 and you'll be surprised how cheap you can get GSRs these days

    • @youtang
      @youtang 6 ปีที่แล้ว

      I did the swap for about $2,300. I did all the work myself so I saved a ton of money. I was able to get an Exedy clutch and Hasport mounts. Also budget in some custom exhaust work. This was my first B series swap and I was able to get it running on the first crank. I almost teared up, but my wife was watching me.

  • @zakattack4274
    @zakattack4274 7 ปีที่แล้ว

    I need some help I guess I'm doing it the hard way b18a1 into a 99 civic ex I have the 93 Acura integra the complete car that the b18 is coming out of

    • @StaufferGarage
      @StaufferGarage  7 ปีที่แล้ว

      It should still be fairly straightforward. You are using a b series engine and might just need to get the mounts I mention to make it fit.

    • @zakattack4274
      @zakattack4274 7 ปีที่แล้ว

      Got one more question the axles I've heard that the 93 axles will fit do you know?

    • @StaufferGarage
      @StaufferGarage  7 ปีที่แล้ว

      Im not sure on that one, Id search on hondatech. I can say for sure that the 94-01 axles will fit into the civic spindles and fit.

  • @that_Tim_guy_
    @that_Tim_guy_ 7 ปีที่แล้ว

    can you explain the difference between the Si post mount vs a CRV post mount? I have used the CRV post mount the same as you but my T Bracket has trouble fitting correctly, I've been told it was bc of the CRV post mount but I don't know if that's the case. Any ideas?

    • @StaufferGarage
      @StaufferGarage  7 ปีที่แล้ว

      +Tim Lowery do you have the civic si t bracket? The si post mount should also be identical because it allows you to use the pancake type mount used on civics. Where as the integra mount is similar to the tranny side where its a large circle mounted horizontal.

    • @that_Tim_guy_
      @that_Tim_guy_ 7 ปีที่แล้ว

      +Stauffer Garage yeah, every mount lines up seemingly correct except the rear bracket, the Si T Bracket, it's like the mount and motor are too close and the T Bracket is very difficult to get in place

    • @StaufferGarage
      @StaufferGarage  7 ปีที่แล้ว

      Did you get it to fit?

    • @that_Tim_guy_
      @that_Tim_guy_ 7 ปีที่แล้ว

      Haven't gotten to try again due to work schedule and weather but as of right now we havent..

    • @that_Tim_guy_
      @that_Tim_guy_ 7 ปีที่แล้ว

      Working on this later today, is there another form of contacting you? I'd like to work out this t bracket mystery bc it's quite frustrating. But I'd like to discuss this without searching for the video each time lol please respond!!

  • @EdithSanchez-qe4hz
    @EdithSanchez-qe4hz 6 ปีที่แล้ว

    What about 1991 da. Acura integra

    • @StaufferGarage
      @StaufferGarage  6 ปีที่แล้ว

      Depends on your budget and time! What power goals do you have?

  • @edwinadalidalvarenga7792
    @edwinadalidalvarenga7792 5 ปีที่แล้ว

    I have a 96 b20b engine on my 99 civic ex could I use this method?

    • @edwinadalidalvarenga7792
      @edwinadalidalvarenga7792 5 ปีที่แล้ว

      For a b18c

    • @StaufferGarage
      @StaufferGarage  5 ปีที่แล้ว

      Yeah it should be pretty close. Only thing different I can think of is if you do or don't have vtec and the GSR intake manifold

  • @hectorrentas6838
    @hectorrentas6838 6 ปีที่แล้ว

    I have a question could you help me please I’m doing a b20 engine on my civic ek 99 what wiring harness do I use and ecu

    • @StaufferGarage
      @StaufferGarage  6 ปีที่แล้ว +1

      OBD2B would be the easiest since that is what is already in the car

    • @danielstephens4420
      @danielstephens4420 5 ปีที่แล้ว +1

      You can't use the integra ls obd2b ecu because of the immobilizer.You need an obd2b to obd2a jumper harness ($35 amazon) to use the 96-98 integra ls ecu.Best option is run a obd2b to 0bd1 jumper.Then buy a socketed chipped obd1 ecu with a crv b20 base map loaded into it.Then have it dynoed and chipped again perfect.It will run ok on the ls integra ecu but it will be lean on start up and some lean spots in the rpm range.

  • @jasonlyle3818
    @jasonlyle3818 6 ปีที่แล้ว

    I have a 95 civic dx and I was wondering what gsr b18s are obd1???

    • @jasonlyle3818
      @jasonlyle3818 6 ปีที่แล้ว

      like what years???

    • @ZFA1738
      @ZFA1738 5 ปีที่แล้ว

      Bookie Anderson 90-95

  • @LK-nu6mg
    @LK-nu6mg 8 ปีที่แล้ว

    I'm thinking of swapping a b series motor into an ek but the ek has an auto tranny. so will I have any problems if I try to install a manual transmission inside?

    • @StaufferGarage
      @StaufferGarage  7 ปีที่แล้ว +1

      You'll just need the pedal box (gas, brake, clutch) from an integra or civic, the clutch master cylinder, manual ECM (should be with your swap), and the clutch master to slave cylinder line.

    • @LK-nu6mg
      @LK-nu6mg 7 ปีที่แล้ว +1

      Stauffer Garage Thank you!

  • @nickmartinez4932
    @nickmartinez4932 8 ปีที่แล้ว

    Can you use stock ek tq mount/brackets, i am also wanting to keep the oem look thanks in advance (using b20b ) .

    • @StaufferGarage
      @StaufferGarage  8 ปีที่แล้ว

      Absolutely, I used GSR torque mounts and all OEM honda mounts.

    • @nickmartinez4932
      @nickmartinez4932 8 ปีที่แล้ว

      Stauffer Garage so use stock tq mount bracket ? With oem rubber mount

    • @StaufferGarage
      @StaufferGarage  8 ปีที่แล้ว

      yes sir.

    • @nickmartinez4932
      @nickmartinez4932 8 ปีที่แล้ว +1

      Stauffer Garage thank you so much look forward to next upload

    • @StaufferGarage
      @StaufferGarage  8 ปีที่แล้ว

      Hopefully have one out by Sunday!